| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* Xilinx CAN device driver |
| 3 |
* |
| 4 |
* Copyright (C) 2012 - 2022 Xilinx, Inc. |
| 5 |
* Copyright (C) 2009 PetaLogix. All rights reserved. |
| 6 |
* Copyright (C) 2017 - 2018 Sandvik Mining and Construction Oy |
| 7 |
* |
| 8 |
* Description: |
| 9 |
* This driver is developed for AXI CAN IP, AXI CANFD IP, CANPS and CANFD PS Controller. |
| 10 |
*/ |
| 11 |
|
| 12 |
#include <linux/bitfield.h> |
| 13 |
#include <linux/clk.h> |
| 14 |
#include <linux/errno.h> |
| 15 |
#include <linux/ethtool.h> |
| 16 |
#include <linux/init.h> |
| 17 |
#include <linux/interrupt.h> |
| 18 |
#include <linux/io.h> |
| 19 |
#include <linux/kernel.h> |
| 20 |
#include <linux/module.h> |
| 21 |
#include <linux/netdevice.h> |
| 22 |
#include <linux/of.h> |
| 23 |
#include <linux/platform_device.h> |
| 24 |
#include <linux/property.h> |
| 25 |
#include <linux/skbuff.h> |
| 26 |
#include <linux/spinlock.h> |
| 27 |
#include <linux/string.h> |
| 28 |
#include <linux/types.h> |
| 29 |
#include <linux/can/dev.h> |
| 30 |
#include <linux/can/error.h> |
| 31 |
#include <linux/phy/phy.h> |
| 32 |
#include <linux/pm_runtime.h> |
| 33 |
#include <linux/reset.h> |
| 34 |
#include <linux/u64_stats_sync.h> |
| 35 |
|
| 36 |
#define DRIVER_NAME "xilinx_can" |
| 37 |
|
| 38 |
/* CAN registers set */ |
| 39 |
enum xcan_reg { |
| 40 |
XCAN_SRR_OFFSET = 0x00, /* Software reset */ |
| 41 |
XCAN_MSR_OFFSET = 0x04, /* Mode select */ |
| 42 |
XCAN_BRPR_OFFSET = 0x08, /* Baud rate prescaler */ |
| 43 |
XCAN_BTR_OFFSET = 0x0C, /* Bit timing */ |
| 44 |
XCAN_ECR_OFFSET = 0x10, /* Error counter */ |
| 45 |
XCAN_ESR_OFFSET = 0x14, /* Error status */ |
| 46 |
XCAN_SR_OFFSET = 0x18, /* Status */ |
| 47 |
XCAN_ISR_OFFSET = 0x1C, /* Interrupt status */ |
| 48 |
XCAN_IER_OFFSET = 0x20, /* Interrupt enable */ |
| 49 |
XCAN_ICR_OFFSET = 0x24, /* Interrupt clear */ |
| 50 |
|
| 51 |
/* not on CAN FD cores */ |
| 52 |
XCAN_TXFIFO_OFFSET = 0x30, /* TX FIFO base */ |
| 53 |
XCAN_RXFIFO_OFFSET = 0x50, /* RX FIFO base */ |
| 54 |
XCAN_AFR_OFFSET = 0x60, /* Acceptance Filter */ |
| 55 |
|
| 56 |
/* only on CAN FD cores */ |
| 57 |
XCAN_F_BRPR_OFFSET = 0x088, /* Data Phase Baud Rate |
| 58 |
* Prescaler |
| 59 |
*/ |
| 60 |
XCAN_F_BTR_OFFSET = 0x08C, /* Data Phase Bit Timing */ |
| 61 |
XCAN_TRR_OFFSET = 0x0090, /* TX Buffer Ready Request */ |
| 62 |
|
| 63 |
/* only on AXI CAN cores */ |
| 64 |
XCAN_ECC_CFG_OFFSET = 0xC8, /* ECC Configuration */ |
| 65 |
XCAN_TXTLFIFO_ECC_OFFSET = 0xCC, /* TXTL FIFO ECC error counter */ |
| 66 |
XCAN_TXOLFIFO_ECC_OFFSET = 0xD0, /* TXOL FIFO ECC error counter */ |
| 67 |
XCAN_RXFIFO_ECC_OFFSET = 0xD4, /* RX FIFO ECC error counter */ |
| 68 |
|
| 69 |
XCAN_AFR_EXT_OFFSET = 0x00E0, /* Acceptance Filter */ |
| 70 |
XCAN_FSR_OFFSET = 0x00E8, /* RX FIFO Status */ |
| 71 |
XCAN_TXMSG_BASE_OFFSET = 0x0100, /* TX Message Space */ |
| 72 |
XCAN_RXMSG_BASE_OFFSET = 0x1100, /* RX Message Space */ |
| 73 |
XCAN_RXMSG_2_BASE_OFFSET = 0x2100, /* RX Message Space */ |
| 74 |
XCAN_AFR_2_MASK_OFFSET = 0x0A00, /* Acceptance Filter MASK */ |
| 75 |
XCAN_AFR_2_ID_OFFSET = 0x0A04, /* Acceptance Filter ID */ |
| 76 |
}; |
| 77 |
|
| 78 |
#define XCAN_FRAME_ID_OFFSET(frame_base) ((frame_base) + 0x00) |
| 79 |
#define XCAN_FRAME_DLC_OFFSET(frame_base) ((frame_base) + 0x04) |
| 80 |
#define XCAN_FRAME_DW1_OFFSET(frame_base) ((frame_base) + 0x08) |
| 81 |
#define XCAN_FRAME_DW2_OFFSET(frame_base) ((frame_base) + 0x0C) |
| 82 |
#define XCANFD_FRAME_DW_OFFSET(frame_base) ((frame_base) + 0x08) |
| 83 |
|
| 84 |
#define XCAN_CANFD_FRAME_SIZE 0x48 |
| 85 |
#define XCAN_TXMSG_FRAME_OFFSET(n) (XCAN_TXMSG_BASE_OFFSET + \ |
| 86 |
XCAN_CANFD_FRAME_SIZE * (n)) |
| 87 |
#define XCAN_RXMSG_FRAME_OFFSET(n) (XCAN_RXMSG_BASE_OFFSET + \ |
| 88 |
XCAN_CANFD_FRAME_SIZE * (n)) |
| 89 |
#define XCAN_RXMSG_2_FRAME_OFFSET(n) (XCAN_RXMSG_2_BASE_OFFSET + \ |
| 90 |
XCAN_CANFD_FRAME_SIZE * (n)) |
| 91 |
|
| 92 |
/* the single TX mailbox used by this driver on CAN FD HW */ |
| 93 |
#define XCAN_TX_MAILBOX_IDX 0 |
| 94 |
|
| 95 |
/* CAN register bit masks - XCAN_<REG>_<BIT>_MASK */ |
| 96 |
#define XCAN_SRR_CEN_MASK 0x00000002 /* CAN enable */ |
| 97 |
#define XCAN_SRR_RESET_MASK 0x00000001 /* Soft Reset the CAN core */ |
| 98 |
#define XCAN_MSR_LBACK_MASK 0x00000002 /* Loop back mode select */ |
| 99 |
#define XCAN_MSR_SLEEP_MASK 0x00000001 /* Sleep mode select */ |
| 100 |
#define XCAN_BRPR_BRP_MASK 0x000000FF /* Baud rate prescaler */ |
| 101 |
#define XCAN_BRPR_TDCO_MASK GENMASK(12, 8) /* TDCO */ |
| 102 |
#define XCAN_2_BRPR_TDCO_MASK GENMASK(13, 8) /* TDCO for CANFD 2.0 */ |
| 103 |
#define XCAN_BTR_SJW_MASK 0x00000180 /* Synchronous jump width */ |
| 104 |
#define XCAN_BTR_TS2_MASK 0x00000070 /* Time segment 2 */ |
| 105 |
#define XCAN_BTR_TS1_MASK 0x0000000F /* Time segment 1 */ |
| 106 |
#define XCAN_BTR_SJW_MASK_CANFD 0x000F0000 /* Synchronous jump width */ |
| 107 |
#define XCAN_BTR_TS2_MASK_CANFD 0x00000F00 /* Time segment 2 */ |
| 108 |
#define XCAN_BTR_TS1_MASK_CANFD 0x0000003F /* Time segment 1 */ |
| 109 |
#define XCAN_ECR_REC_MASK 0x0000FF00 /* Receive error counter */ |
| 110 |
#define XCAN_ECR_TEC_MASK 0x000000FF /* Transmit error counter */ |
| 111 |
#define XCAN_ESR_ACKER_MASK 0x00000010 /* ACK error */ |
| 112 |
#define XCAN_ESR_BERR_MASK 0x00000008 /* Bit error */ |
| 113 |
#define XCAN_ESR_STER_MASK 0x00000004 /* Stuff error */ |
| 114 |
#define XCAN_ESR_FMER_MASK 0x00000002 /* Form error */ |
| 115 |
#define XCAN_ESR_CRCER_MASK 0x00000001 /* CRC error */ |
| 116 |
#define XCAN_SR_TDCV_MASK GENMASK(22, 16) /* TDCV Value */ |
| 117 |
#define XCAN_SR_TXFLL_MASK 0x00000400 /* TX FIFO is full */ |
| 118 |
#define XCAN_SR_ESTAT_MASK 0x00000180 /* Error status */ |
| 119 |
#define XCAN_SR_ERRWRN_MASK 0x00000040 /* Error warning */ |
| 120 |
#define XCAN_SR_NORMAL_MASK 0x00000008 /* Normal mode */ |
| 121 |
#define XCAN_SR_LBACK_MASK 0x00000002 /* Loop back mode */ |
| 122 |
#define XCAN_SR_CONFIG_MASK 0x00000001 /* Configuration mode */ |
| 123 |
#define XCAN_IXR_RXMNF_MASK 0x00020000 /* RX match not finished */ |
| 124 |
#define XCAN_IXR_TXFEMP_MASK 0x00004000 /* TX FIFO Empty */ |
| 125 |
#define XCAN_IXR_WKUP_MASK 0x00000800 /* Wake up interrupt */ |
| 126 |
#define XCAN_IXR_SLP_MASK 0x00000400 /* Sleep interrupt */ |
| 127 |
#define XCAN_IXR_BSOFF_MASK 0x00000200 /* Bus off interrupt */ |
| 128 |
#define XCAN_IXR_ERROR_MASK 0x00000100 /* Error interrupt */ |
| 129 |
#define XCAN_IXR_RXNEMP_MASK 0x00000080 /* RX FIFO NotEmpty intr */ |
| 130 |
#define XCAN_IXR_RXOFLW_MASK 0x00000040 /* RX FIFO Overflow intr */ |
| 131 |
#define XCAN_IXR_RXOK_MASK 0x00000010 /* Message received intr */ |
| 132 |
#define XCAN_IXR_TXFLL_MASK 0x00000004 /* Tx FIFO Full intr */ |
| 133 |
#define XCAN_IXR_TXOK_MASK 0x00000002 /* TX successful intr */ |
| 134 |
#define XCAN_IXR_ARBLST_MASK 0x00000001 /* Arbitration lost intr */ |
| 135 |
#define XCAN_IXR_E2BERX_MASK BIT(23) /* RX FIFO two bit ECC error */ |
| 136 |
#define XCAN_IXR_E1BERX_MASK BIT(22) /* RX FIFO one bit ECC error */ |
| 137 |
#define XCAN_IXR_E2BETXOL_MASK BIT(21) /* TXOL FIFO two bit ECC error */ |
| 138 |
#define XCAN_IXR_E1BETXOL_MASK BIT(20) /* TXOL FIFO One bit ECC error */ |
| 139 |
#define XCAN_IXR_E2BETXTL_MASK BIT(19) /* TXTL FIFO Two bit ECC error */ |
| 140 |
#define XCAN_IXR_E1BETXTL_MASK BIT(18) /* TXTL FIFO One bit ECC error */ |
| 141 |
#define XCAN_IXR_ECC_MASK (XCAN_IXR_E2BERX_MASK | \ |
| 142 |
XCAN_IXR_E1BERX_MASK | \ |
| 143 |
XCAN_IXR_E2BETXOL_MASK | \ |
| 144 |
XCAN_IXR_E1BETXOL_MASK | \ |
| 145 |
XCAN_IXR_E2BETXTL_MASK | \ |
| 146 |
XCAN_IXR_E1BETXTL_MASK) |
| 147 |
#define XCAN_IDR_ID1_MASK 0xFFE00000 /* Standard msg identifier */ |
| 148 |
#define XCAN_IDR_SRR_MASK 0x00100000 /* Substitute remote TXreq */ |
| 149 |
#define XCAN_IDR_IDE_MASK 0x00080000 /* Identifier extension */ |
| 150 |
#define XCAN_IDR_ID2_MASK 0x0007FFFE /* Extended message ident */ |
| 151 |
#define XCAN_IDR_RTR_MASK 0x00000001 /* Remote TX request */ |
| 152 |
#define XCAN_DLCR_DLC_MASK 0xF0000000 /* Data length code */ |
| 153 |
#define XCAN_FSR_FL_MASK 0x00003F00 /* RX Fill Level */ |
| 154 |
#define XCAN_2_FSR_FL_MASK 0x00007F00 /* RX Fill Level */ |
| 155 |
#define XCAN_FSR_IRI_MASK 0x00000080 /* RX Increment Read Index */ |
| 156 |
#define XCAN_FSR_RI_MASK 0x0000001F /* RX Read Index */ |
| 157 |
#define XCAN_2_FSR_RI_MASK 0x0000003F /* RX Read Index */ |
| 158 |
#define XCAN_DLCR_EDL_MASK 0x08000000 /* EDL Mask in DLC */ |
| 159 |
#define XCAN_DLCR_BRS_MASK 0x04000000 /* BRS Mask in DLC */ |
| 160 |
#define XCAN_ECC_CFG_REECRX_MASK BIT(2) /* Reset RX FIFO ECC error counters */ |
| 161 |
#define XCAN_ECC_CFG_REECTXOL_MASK BIT(1) /* Reset TXOL FIFO ECC error counters */ |
| 162 |
#define XCAN_ECC_CFG_REECTXTL_MASK BIT(0) /* Reset TXTL FIFO ECC error counters */ |
| 163 |
#define XCAN_ECC_1BIT_CNT_MASK GENMASK(15, 0) /* FIFO ECC 1bit count mask */ |
| 164 |
#define XCAN_ECC_2BIT_CNT_MASK GENMASK(31, 16) /* FIFO ECC 2bit count mask */ |
| 165 |
|
| 166 |
/* CAN register bit shift - XCAN_<REG>_<BIT>_SHIFT */ |
| 167 |
#define XCAN_BRPR_TDC_ENABLE BIT(16) /* Transmitter Delay Compensation (TDC) Enable */ |
| 168 |
#define XCAN_BTR_SJW_SHIFT 7 /* Synchronous jump width */ |
| 169 |
#define XCAN_BTR_TS2_SHIFT 4 /* Time segment 2 */ |
| 170 |
#define XCAN_BTR_SJW_SHIFT_CANFD 16 /* Synchronous jump width */ |
| 171 |
#define XCAN_BTR_TS2_SHIFT_CANFD 8 /* Time segment 2 */ |
| 172 |
#define XCAN_IDR_ID1_SHIFT 21 /* Standard Messg Identifier */ |
| 173 |
#define XCAN_IDR_ID2_SHIFT 1 /* Extended Message Identifier */ |
| 174 |
#define XCAN_DLCR_DLC_SHIFT 28 /* Data length code */ |
| 175 |
#define XCAN_ESR_REC_SHIFT 8 /* Rx Error Count */ |
| 176 |
|
| 177 |
/* CAN frame length constants */ |
| 178 |
#define XCAN_FRAME_MAX_DATA_LEN 8 |
| 179 |
#define XCANFD_DW_BYTES 4 |
| 180 |
#define XCAN_TIMEOUT (1 * HZ) |
| 181 |
|
| 182 |
/* TX-FIFO-empty interrupt available */ |
| 183 |
#define XCAN_FLAG_TXFEMP 0x0001 |
| 184 |
/* RX Match Not Finished interrupt available */ |
| 185 |
#define XCAN_FLAG_RXMNF 0x0002 |
| 186 |
/* Extended acceptance filters with control at 0xE0 */ |
| 187 |
#define XCAN_FLAG_EXT_FILTERS 0x0004 |
| 188 |
/* TX mailboxes instead of TX FIFO */ |
| 189 |
#define XCAN_FLAG_TX_MAILBOXES 0x0008 |
| 190 |
/* RX FIFO with each buffer in separate registers at 0x1100 |
| 191 |
* instead of the regular FIFO at 0x50 |
| 192 |
*/ |
| 193 |
#define XCAN_FLAG_RX_FIFO_MULTI 0x0010 |
| 194 |
#define XCAN_FLAG_CANFD_2 0x0020 |
| 195 |
|
| 196 |
enum xcan_ip_type { |
| 197 |
XAXI_CAN = 0, |
| 198 |
XZYNQ_CANPS, |
| 199 |
XAXI_CANFD, |
| 200 |
XAXI_CANFD_2_0, |
| 201 |
}; |
| 202 |
|
| 203 |
struct xcan_devtype_data { |
| 204 |
enum xcan_ip_type cantype; |
| 205 |
unsigned int flags; |
| 206 |
const struct can_bittiming_const *bittiming_const; |
| 207 |
const char *bus_clk_name; |
| 208 |
unsigned int btr_ts2_shift; |
| 209 |
unsigned int btr_sjw_shift; |
| 210 |
}; |
| 211 |
|
| 212 |
/** |
| 213 |
* struct xcan_priv - This definition define CAN driver instance |
| 214 |
* @can: CAN private data structure. |
| 215 |
* @tx_lock: Lock for synchronizing TX interrupt handling |
| 216 |
* @tx_head: Tx CAN packets ready to send on the queue |
| 217 |
* @tx_tail: Tx CAN packets successfully sended on the queue |
| 218 |
* @tx_max: Maximum number packets the driver can send |
| 219 |
* @napi: NAPI structure |
| 220 |
* @read_reg: For reading data from CAN registers |
| 221 |
* @write_reg: For writing data to CAN registers |
| 222 |
* @dev: Network device data structure |
| 223 |
* @reg_base: Ioremapped address to registers |
| 224 |
* @irq_flags: For request_irq() |
| 225 |
* @bus_clk: Pointer to struct clk |
| 226 |
* @can_clk: Pointer to struct clk |
| 227 |
* @devtype: Device type specific constants |
| 228 |
* @transceiver: Optional pointer to associated CAN transceiver |
| 229 |
* @rstc: Pointer to reset control |
| 230 |
* @ecc_enable: ECC enable flag |
| 231 |
* @syncp: synchronization for ECC error stats |
| 232 |
* @ecc_rx_2_bit_errors: RXFIFO 2bit ECC count |
| 233 |
* @ecc_rx_1_bit_errors: RXFIFO 1bit ECC count |
| 234 |
* @ecc_txol_2_bit_errors: TXOLFIFO 2bit ECC count |
| 235 |
* @ecc_txol_1_bit_errors: TXOLFIFO 1bit ECC count |
| 236 |
* @ecc_txtl_2_bit_errors: TXTLFIFO 2bit ECC count |
| 237 |
* @ecc_txtl_1_bit_errors: TXTLFIFO 1bit ECC count |
| 238 |
*/ |
| 239 |
struct xcan_priv { |
| 240 |
struct can_priv can; |
| 241 |
spinlock_t tx_lock; /* Lock for synchronizing TX interrupt handling */ |
| 242 |
unsigned int tx_head; |
| 243 |
unsigned int tx_tail; |
| 244 |
unsigned int tx_max; |
| 245 |
struct napi_struct napi; |
| 246 |
u32 (*read_reg)(const struct xcan_priv *priv, enum xcan_reg reg); |
| 247 |
void (*write_reg)(const struct xcan_priv *priv, enum xcan_reg reg, |
| 248 |
u32 val); |
| 249 |
struct device *dev; |
| 250 |
void __iomem *reg_base; |
| 251 |
unsigned long irq_flags; |
| 252 |
struct clk *bus_clk; |
| 253 |
struct clk *can_clk; |
| 254 |
struct xcan_devtype_data devtype; |
| 255 |
struct phy *transceiver; |
| 256 |
struct reset_control *rstc; |
| 257 |
bool ecc_enable; |
| 258 |
struct u64_stats_sync syncp; |
| 259 |
u64_stats_t ecc_rx_2_bit_errors; |
| 260 |
u64_stats_t ecc_rx_1_bit_errors; |
| 261 |
u64_stats_t ecc_txol_2_bit_errors; |
| 262 |
u64_stats_t ecc_txol_1_bit_errors; |
| 263 |
u64_stats_t ecc_txtl_2_bit_errors; |
| 264 |
u64_stats_t ecc_txtl_1_bit_errors; |
| 265 |
}; |
| 266 |
|
| 267 |
/* CAN Bittiming constants as per Xilinx CAN specs */ |
| 268 |
static const struct can_bittiming_const xcan_bittiming_const = { |
| 269 |
.name = DRIVER_NAME, |
| 270 |
.tseg1_min = 1, |
| 271 |
.tseg1_max = 16, |
| 272 |
.tseg2_min = 1, |
| 273 |
.tseg2_max = 8, |
| 274 |
.sjw_max = 4, |
| 275 |
.brp_min = 1, |
| 276 |
.brp_max = 256, |
| 277 |
.brp_inc = 1, |
| 278 |
}; |
| 279 |
|
| 280 |
/* AXI CANFD Arbitration Bittiming constants as per AXI CANFD 1.0 spec */ |
| 281 |
static const struct can_bittiming_const xcan_bittiming_const_canfd = { |
| 282 |
.name = DRIVER_NAME, |
| 283 |
.tseg1_min = 1, |
| 284 |
.tseg1_max = 64, |
| 285 |
.tseg2_min = 1, |
| 286 |
.tseg2_max = 16, |
| 287 |
.sjw_max = 16, |
| 288 |
.brp_min = 1, |
| 289 |
.brp_max = 256, |
| 290 |
.brp_inc = 1, |
| 291 |
}; |
| 292 |
|
| 293 |
/* AXI CANFD Data Bittiming constants as per AXI CANFD 1.0 specs */ |
| 294 |
static const struct can_bittiming_const xcan_data_bittiming_const_canfd = { |
| 295 |
.name = DRIVER_NAME, |
| 296 |
.tseg1_min = 1, |
| 297 |
.tseg1_max = 16, |
| 298 |
.tseg2_min = 1, |
| 299 |
.tseg2_max = 8, |
| 300 |
.sjw_max = 8, |
| 301 |
.brp_min = 1, |
| 302 |
.brp_max = 256, |
| 303 |
.brp_inc = 1, |
| 304 |
}; |
| 305 |
|
| 306 |
/* AXI CANFD 2.0 Arbitration Bittiming constants as per AXI CANFD 2.0 spec */ |
| 307 |
static const struct can_bittiming_const xcan_bittiming_const_canfd2 = { |
| 308 |
.name = DRIVER_NAME, |
| 309 |
.tseg1_min = 1, |
| 310 |
.tseg1_max = 256, |
| 311 |
.tseg2_min = 1, |
| 312 |
.tseg2_max = 128, |
| 313 |
.sjw_max = 128, |
| 314 |
.brp_min = 1, |
| 315 |
.brp_max = 256, |
| 316 |
.brp_inc = 1, |
| 317 |
}; |
| 318 |
|
| 319 |
/* AXI CANFD 2.0 Data Bittiming constants as per AXI CANFD 2.0 spec */ |
| 320 |
static const struct can_bittiming_const xcan_data_bittiming_const_canfd2 = { |
| 321 |
.name = DRIVER_NAME, |
| 322 |
.tseg1_min = 1, |
| 323 |
.tseg1_max = 32, |
| 324 |
.tseg2_min = 1, |
| 325 |
.tseg2_max = 16, |
| 326 |
.sjw_max = 16, |
| 327 |
.brp_min = 1, |
| 328 |
.brp_max = 256, |
| 329 |
.brp_inc = 1, |
| 330 |
}; |
| 331 |
|
| 332 |
/* Transmission Delay Compensation constants for CANFD 1.0 */ |
| 333 |
static const struct can_tdc_const xcan_tdc_const_canfd = { |
| 334 |
.tdcv_min = 0, |
| 335 |
.tdcv_max = 0, /* Manual mode not supported. */ |
| 336 |
.tdco_min = 0, |
| 337 |
.tdco_max = 32, |
| 338 |
.tdcf_min = 0, /* Filter window not supported */ |
| 339 |
.tdcf_max = 0, |
| 340 |
}; |
| 341 |
|
| 342 |
/* Transmission Delay Compensation constants for CANFD 2.0 */ |
| 343 |
static const struct can_tdc_const xcan_tdc_const_canfd2 = { |
| 344 |
.tdcv_min = 0, |
| 345 |
.tdcv_max = 0, /* Manual mode not supported. */ |
| 346 |
.tdco_min = 0, |
| 347 |
.tdco_max = 64, |
| 348 |
.tdcf_min = 0, /* Filter window not supported */ |
| 349 |
.tdcf_max = 0, |
| 350 |
}; |
| 351 |
|
| 352 |
enum xcan_stats_type { |
| 353 |
XCAN_ECC_RX_2_BIT_ERRORS, |
| 354 |
XCAN_ECC_RX_1_BIT_ERRORS, |
| 355 |
XCAN_ECC_TXOL_2_BIT_ERRORS, |
| 356 |
XCAN_ECC_TXOL_1_BIT_ERRORS, |
| 357 |
XCAN_ECC_TXTL_2_BIT_ERRORS, |
| 358 |
XCAN_ECC_TXTL_1_BIT_ERRORS, |
| 359 |
}; |
| 360 |
|
| 361 |
static const char xcan_priv_flags_strings[][ETH_GSTRING_LEN] = { |
| 362 |
[XCAN_ECC_RX_2_BIT_ERRORS] = "ecc_rx_2_bit_errors", |
| 363 |
[XCAN_ECC_RX_1_BIT_ERRORS] = "ecc_rx_1_bit_errors", |
| 364 |
[XCAN_ECC_TXOL_2_BIT_ERRORS] = "ecc_txol_2_bit_errors", |
| 365 |
[XCAN_ECC_TXOL_1_BIT_ERRORS] = "ecc_txol_1_bit_errors", |
| 366 |
[XCAN_ECC_TXTL_2_BIT_ERRORS] = "ecc_txtl_2_bit_errors", |
| 367 |
[XCAN_ECC_TXTL_1_BIT_ERRORS] = "ecc_txtl_1_bit_errors", |
| 368 |
}; |
| 369 |
|
| 370 |
/** |
| 371 |
* xcan_write_reg_le - Write a value to the device register little endian |
| 372 |
* @priv: Driver private data structure |
| 373 |
* @reg: Register offset |
| 374 |
* @val: Value to write at the Register offset |
| 375 |
* |
| 376 |
* Write data to the paricular CAN register |
| 377 |
*/ |
| 378 |
static void xcan_write_reg_le(const struct xcan_priv *priv, enum xcan_reg reg, |
| 379 |
u32 val) |
| 380 |
{ |
| 381 |
iowrite32(val, priv->reg_base + reg); |
| 382 |
} |
| 383 |
|
| 384 |
/** |
| 385 |
* xcan_read_reg_le - Read a value from the device register little endian |
| 386 |
* @priv: Driver private data structure |
| 387 |
* @reg: Register offset |
| 388 |
* |
| 389 |
* Read data from the particular CAN register |
| 390 |
* Return: value read from the CAN register |
| 391 |
*/ |
| 392 |
static u32 xcan_read_reg_le(const struct xcan_priv *priv, enum xcan_reg reg) |
| 393 |
{ |
| 394 |
return ioread32(priv->reg_base + reg); |
| 395 |
} |
| 396 |
|
| 397 |
/** |
| 398 |
* xcan_write_reg_be - Write a value to the device register big endian |
| 399 |
* @priv: Driver private data structure |
| 400 |
* @reg: Register offset |
| 401 |
* @val: Value to write at the Register offset |
| 402 |
* |
| 403 |
* Write data to the paricular CAN register |
| 404 |
*/ |
| 405 |
static void xcan_write_reg_be(const struct xcan_priv *priv, enum xcan_reg reg, |
| 406 |
u32 val) |
| 407 |
{ |
| 408 |
iowrite32be(val, priv->reg_base + reg); |
| 409 |
} |
| 410 |
|
| 411 |
/** |
| 412 |
* xcan_read_reg_be - Read a value from the device register big endian |
| 413 |
* @priv: Driver private data structure |
| 414 |
* @reg: Register offset |
| 415 |
* |
| 416 |
* Read data from the particular CAN register |
| 417 |
* Return: value read from the CAN register |
| 418 |
*/ |
| 419 |
static u32 xcan_read_reg_be(const struct xcan_priv *priv, enum xcan_reg reg) |
| 420 |
{ |
| 421 |
return ioread32be(priv->reg_base + reg); |
| 422 |
} |
| 423 |
|
| 424 |
/** |
| 425 |
* xcan_rx_int_mask - Get the mask for the receive interrupt |
| 426 |
* @priv: Driver private data structure |
| 427 |
* |
| 428 |
* Return: The receive interrupt mask used by the driver on this HW |
| 429 |
*/ |
| 430 |
static u32 xcan_rx_int_mask(const struct xcan_priv *priv) |
| 431 |
{ |
| 432 |
/* RXNEMP is better suited for our use case as it cannot be cleared |
| 433 |
* while the FIFO is non-empty, but CAN FD HW does not have it |
| 434 |
*/ |
| 435 |
if (priv->devtype.flags & XCAN_FLAG_RX_FIFO_MULTI) |
| 436 |
return XCAN_IXR_RXOK_MASK; |
| 437 |
else |
| 438 |
return XCAN_IXR_RXNEMP_MASK; |
| 439 |
} |
| 440 |
|
| 441 |
/** |
| 442 |
* set_reset_mode - Resets the CAN device mode |
| 443 |
* @ndev: Pointer to net_device structure |
| 444 |
* |
| 445 |
* This is the driver reset mode routine.The driver |
| 446 |
* enters into configuration mode. |
| 447 |
* |
| 448 |
* Return: 0 on success and failure value on error |
| 449 |
*/ |
| 450 |
static int set_reset_mode(struct net_device *ndev) |
| 451 |
{ |
| 452 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 453 |
unsigned long timeout; |
| 454 |
|
| 455 |
priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK); |
| 456 |
|
| 457 |
timeout = jiffies + XCAN_TIMEOUT; |
| 458 |
while (!(priv->read_reg(priv, XCAN_SR_OFFSET) & XCAN_SR_CONFIG_MASK)) { |
| 459 |
if (time_after(jiffies, timeout)) { |
| 460 |
netdev_warn(ndev, "timed out for config mode\n"); |
| 461 |
return -ETIMEDOUT; |
| 462 |
} |
| 463 |
usleep_range(500, 10000); |
| 464 |
} |
| 465 |
|
| 466 |
/* reset clears FIFOs */ |
| 467 |
priv->tx_head = 0; |
| 468 |
priv->tx_tail = 0; |
| 469 |
|
| 470 |
return 0; |
| 471 |
} |
| 472 |
|
| 473 |
/** |
| 474 |
* xcan_set_bittiming - CAN set bit timing routine |
| 475 |
* @ndev: Pointer to net_device structure |
| 476 |
* |
| 477 |
* This is the driver set bittiming routine. |
| 478 |
* Return: 0 on success and failure value on error |
| 479 |
*/ |
| 480 |
static int xcan_set_bittiming(struct net_device *ndev) |
| 481 |
{ |
| 482 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 483 |
struct can_bittiming *bt = &priv->can.bittiming; |
| 484 |
struct can_bittiming *dbt = &priv->can.fd.data_bittiming; |
| 485 |
u32 btr0, btr1; |
| 486 |
u32 is_config_mode; |
| 487 |
|
| 488 |
/* Check whether Xilinx CAN is in configuration mode. |
| 489 |
* It cannot set bit timing if Xilinx CAN is not in configuration mode. |
| 490 |
*/ |
| 491 |
is_config_mode = priv->read_reg(priv, XCAN_SR_OFFSET) & |
| 492 |
XCAN_SR_CONFIG_MASK; |
| 493 |
if (!is_config_mode) { |
| 494 |
netdev_alert(ndev, |
| 495 |
"BUG! Cannot set bittiming - CAN is not in config mode\n"); |
| 496 |
return -EPERM; |
| 497 |
} |
| 498 |
|
| 499 |
/* Setting Baud Rate prescaler value in BRPR Register */ |
| 500 |
btr0 = (bt->brp - 1); |
| 501 |
|
| 502 |
/* Setting Time Segment 1 in BTR Register */ |
| 503 |
btr1 = (bt->prop_seg + bt->phase_seg1 - 1); |
| 504 |
|
| 505 |
/* Setting Time Segment 2 in BTR Register */ |
| 506 |
btr1 |= (bt->phase_seg2 - 1) << priv->devtype.btr_ts2_shift; |
| 507 |
|
| 508 |
/* Setting Synchronous jump width in BTR Register */ |
| 509 |
btr1 |= (bt->sjw - 1) << priv->devtype.btr_sjw_shift; |
| 510 |
|
| 511 |
priv->write_reg(priv, XCAN_BRPR_OFFSET, btr0); |
| 512 |
priv->write_reg(priv, XCAN_BTR_OFFSET, btr1); |
| 513 |
|
| 514 |
if (priv->devtype.cantype == XAXI_CANFD || |
| 515 |
priv->devtype.cantype == XAXI_CANFD_2_0) { |
| 516 |
/* Setting Baud Rate prescaler value in F_BRPR Register */ |
| 517 |
btr0 = dbt->brp - 1; |
| 518 |
if (can_fd_tdc_is_enabled(&priv->can)) { |
| 519 |
if (priv->devtype.cantype == XAXI_CANFD) |
| 520 |
btr0 |= FIELD_PREP(XCAN_BRPR_TDCO_MASK, priv->can.fd.tdc.tdco) | |
| 521 |
XCAN_BRPR_TDC_ENABLE; |
| 522 |
else |
| 523 |
btr0 |= FIELD_PREP(XCAN_2_BRPR_TDCO_MASK, priv->can.fd.tdc.tdco) | |
| 524 |
XCAN_BRPR_TDC_ENABLE; |
| 525 |
} |
| 526 |
|
| 527 |
/* Setting Time Segment 1 in BTR Register */ |
| 528 |
btr1 = dbt->prop_seg + dbt->phase_seg1 - 1; |
| 529 |
|
| 530 |
/* Setting Time Segment 2 in BTR Register */ |
| 531 |
btr1 |= (dbt->phase_seg2 - 1) << priv->devtype.btr_ts2_shift; |
| 532 |
|
| 533 |
/* Setting Synchronous jump width in BTR Register */ |
| 534 |
btr1 |= (dbt->sjw - 1) << priv->devtype.btr_sjw_shift; |
| 535 |
|
| 536 |
priv->write_reg(priv, XCAN_F_BRPR_OFFSET, btr0); |
| 537 |
priv->write_reg(priv, XCAN_F_BTR_OFFSET, btr1); |
| 538 |
} |
| 539 |
|
| 540 |
netdev_dbg(ndev, "BRPR=0x%08x, BTR=0x%08x\n", |
| 541 |
priv->read_reg(priv, XCAN_BRPR_OFFSET), |
| 542 |
priv->read_reg(priv, XCAN_BTR_OFFSET)); |
| 543 |
|
| 544 |
return 0; |
| 545 |
} |
| 546 |
|
| 547 |
/** |
| 548 |
* xcan_chip_start - This the drivers start routine |
| 549 |
* @ndev: Pointer to net_device structure |
| 550 |
* |
| 551 |
* This is the drivers start routine. |
| 552 |
* Based on the State of the CAN device it puts |
| 553 |
* the CAN device into a proper mode. |
| 554 |
* |
| 555 |
* Return: 0 on success and failure value on error |
| 556 |
*/ |
| 557 |
static int xcan_chip_start(struct net_device *ndev) |
| 558 |
{ |
| 559 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 560 |
u32 reg_msr; |
| 561 |
int err; |
| 562 |
u32 ier; |
| 563 |
|
| 564 |
/* Check if it is in reset mode */ |
| 565 |
err = set_reset_mode(ndev); |
| 566 |
if (err < 0) |
| 567 |
return err; |
| 568 |
|
| 569 |
err = xcan_set_bittiming(ndev); |
| 570 |
if (err < 0) |
| 571 |
return err; |
| 572 |
|
| 573 |
/* Enable interrupts |
| 574 |
* |
| 575 |
* We enable the ERROR interrupt even with |
| 576 |
* CAN_CTRLMODE_BERR_REPORTING disabled as there is no |
| 577 |
* dedicated interrupt for a state change to |
| 578 |
* ERROR_WARNING/ERROR_PASSIVE. |
| 579 |
*/ |
| 580 |
ier = XCAN_IXR_TXOK_MASK | XCAN_IXR_BSOFF_MASK | |
| 581 |
XCAN_IXR_WKUP_MASK | XCAN_IXR_SLP_MASK | |
| 582 |
XCAN_IXR_ERROR_MASK | XCAN_IXR_RXOFLW_MASK | |
| 583 |
XCAN_IXR_ARBLST_MASK | xcan_rx_int_mask(priv); |
| 584 |
|
| 585 |
if (priv->ecc_enable) |
| 586 |
ier |= XCAN_IXR_ECC_MASK; |
| 587 |
|
| 588 |
if (priv->devtype.flags & XCAN_FLAG_RXMNF) |
| 589 |
ier |= XCAN_IXR_RXMNF_MASK; |
| 590 |
|
| 591 |
priv->write_reg(priv, XCAN_IER_OFFSET, ier); |
| 592 |
|
| 593 |
/* Check whether it is loopback mode or normal mode */ |
| 594 |
if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK) |
| 595 |
reg_msr = XCAN_MSR_LBACK_MASK; |
| 596 |
else |
| 597 |
reg_msr = 0x0; |
| 598 |
|
| 599 |
/* enable the first extended filter, if any, as cores with extended |
| 600 |
* filtering default to non-receipt if all filters are disabled |
| 601 |
*/ |
| 602 |
if (priv->devtype.flags & XCAN_FLAG_EXT_FILTERS) |
| 603 |
priv->write_reg(priv, XCAN_AFR_EXT_OFFSET, 0x00000001); |
| 604 |
|
| 605 |
priv->write_reg(priv, XCAN_MSR_OFFSET, reg_msr); |
| 606 |
priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_CEN_MASK); |
| 607 |
|
| 608 |
netdev_dbg(ndev, "status:#x%08x\n", |
| 609 |
priv->read_reg(priv, XCAN_SR_OFFSET)); |
| 610 |
|
| 611 |
priv->can.state = CAN_STATE_ERROR_ACTIVE; |
| 612 |
return 0; |
| 613 |
} |
| 614 |
|
| 615 |
/** |
| 616 |
* xcan_do_set_mode - This sets the mode of the driver |
| 617 |
* @ndev: Pointer to net_device structure |
| 618 |
* @mode: Tells the mode of the driver |
| 619 |
* |
| 620 |
* This check the drivers state and calls the corresponding modes to set. |
| 621 |
* |
| 622 |
* Return: 0 on success and failure value on error |
| 623 |
*/ |
| 624 |
static int xcan_do_set_mode(struct net_device *ndev, enum can_mode mode) |
| 625 |
{ |
| 626 |
int ret; |
| 627 |
|
| 628 |
switch (mode) { |
| 629 |
case CAN_MODE_START: |
| 630 |
ret = xcan_chip_start(ndev); |
| 631 |
if (ret < 0) { |
| 632 |
netdev_err(ndev, "xcan_chip_start failed!\n"); |
| 633 |
return ret; |
| 634 |
} |
| 635 |
netif_wake_queue(ndev); |
| 636 |
break; |
| 637 |
default: |
| 638 |
ret = -EOPNOTSUPP; |
| 639 |
break; |
| 640 |
} |
| 641 |
|
| 642 |
return ret; |
| 643 |
} |
| 644 |
|
| 645 |
/** |
| 646 |
* xcan_write_frame - Write a frame to HW |
| 647 |
* @ndev: Pointer to net_device structure |
| 648 |
* @skb: sk_buff pointer that contains data to be Txed |
| 649 |
* @frame_offset: Register offset to write the frame to |
| 650 |
*/ |
| 651 |
static void xcan_write_frame(struct net_device *ndev, struct sk_buff *skb, |
| 652 |
int frame_offset) |
| 653 |
{ |
| 654 |
u32 id, dlc, data[2] = {0, 0}; |
| 655 |
struct canfd_frame *cf = (struct canfd_frame *)skb->data; |
| 656 |
u32 ramoff, dwindex = 0, i; |
| 657 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 658 |
|
| 659 |
/* Watch carefully on the bit sequence */ |
| 660 |
if (cf->can_id & CAN_EFF_FLAG) { |
| 661 |
/* Extended CAN ID format */ |
| 662 |
id = ((cf->can_id & CAN_EFF_MASK) << XCAN_IDR_ID2_SHIFT) & |
| 663 |
XCAN_IDR_ID2_MASK; |
| 664 |
id |= (((cf->can_id & CAN_EFF_MASK) >> |
| 665 |
(CAN_EFF_ID_BITS - CAN_SFF_ID_BITS)) << |
| 666 |
XCAN_IDR_ID1_SHIFT) & XCAN_IDR_ID1_MASK; |
| 667 |
|
| 668 |
/* The substibute remote TX request bit should be "1" |
| 669 |
* for extended frames as in the Xilinx CAN datasheet |
| 670 |
*/ |
| 671 |
id |= XCAN_IDR_IDE_MASK | XCAN_IDR_SRR_MASK; |
| 672 |
|
| 673 |
if (cf->can_id & CAN_RTR_FLAG) |
| 674 |
/* Extended frames remote TX request */ |
| 675 |
id |= XCAN_IDR_RTR_MASK; |
| 676 |
} else { |
| 677 |
/* Standard CAN ID format */ |
| 678 |
id = ((cf->can_id & CAN_SFF_MASK) << XCAN_IDR_ID1_SHIFT) & |
| 679 |
XCAN_IDR_ID1_MASK; |
| 680 |
|
| 681 |
if (cf->can_id & CAN_RTR_FLAG) |
| 682 |
/* Standard frames remote TX request */ |
| 683 |
id |= XCAN_IDR_SRR_MASK; |
| 684 |
} |
| 685 |
|
| 686 |
dlc = can_fd_len2dlc(cf->len) << XCAN_DLCR_DLC_SHIFT; |
| 687 |
if (can_is_canfd_skb(skb)) { |
| 688 |
if (cf->flags & CANFD_BRS) |
| 689 |
dlc |= XCAN_DLCR_BRS_MASK; |
| 690 |
dlc |= XCAN_DLCR_EDL_MASK; |
| 691 |
} |
| 692 |
|
| 693 |
priv->write_reg(priv, XCAN_FRAME_ID_OFFSET(frame_offset), id); |
| 694 |
/* If the CAN frame is RTR frame this write triggers transmission |
| 695 |
* (not on CAN FD) |
| 696 |
*/ |
| 697 |
priv->write_reg(priv, XCAN_FRAME_DLC_OFFSET(frame_offset), dlc); |
| 698 |
if (priv->devtype.cantype == XAXI_CANFD || |
| 699 |
priv->devtype.cantype == XAXI_CANFD_2_0) { |
| 700 |
for (i = 0; i < cf->len; i += 4) { |
| 701 |
ramoff = XCANFD_FRAME_DW_OFFSET(frame_offset) + |
| 702 |
(dwindex * XCANFD_DW_BYTES); |
| 703 |
priv->write_reg(priv, ramoff, |
| 704 |
be32_to_cpup((__be32 *)(cf->data + i))); |
| 705 |
dwindex++; |
| 706 |
} |
| 707 |
} else { |
| 708 |
if (cf->len > 0) |
| 709 |
data[0] = be32_to_cpup((__be32 *)(cf->data + 0)); |
| 710 |
if (cf->len > 4) |
| 711 |
data[1] = be32_to_cpup((__be32 *)(cf->data + 4)); |
| 712 |
|
| 713 |
if (!(cf->can_id & CAN_RTR_FLAG)) { |
| 714 |
priv->write_reg(priv, |
| 715 |
XCAN_FRAME_DW1_OFFSET(frame_offset), |
| 716 |
data[0]); |
| 717 |
/* If the CAN frame is Standard/Extended frame this |
| 718 |
* write triggers transmission (not on CAN FD) |
| 719 |
*/ |
| 720 |
priv->write_reg(priv, |
| 721 |
XCAN_FRAME_DW2_OFFSET(frame_offset), |
| 722 |
data[1]); |
| 723 |
} |
| 724 |
} |
| 725 |
|
| 726 |
if (!(priv->devtype.flags & XCAN_FLAG_TX_MAILBOXES) && |
| 727 |
(priv->devtype.flags & XCAN_FLAG_TXFEMP)) |
| 728 |
can_put_echo_skb(skb, ndev, priv->tx_head % priv->tx_max, 0); |
| 729 |
else |
| 730 |
can_put_echo_skb(skb, ndev, 0, 0); |
| 731 |
|
| 732 |
priv->tx_head++; |
| 733 |
} |
| 734 |
|
| 735 |
/** |
| 736 |
* xcan_start_xmit_fifo - Starts the transmission (FIFO mode) |
| 737 |
* @skb: sk_buff pointer that contains data to be Txed |
| 738 |
* @ndev: Pointer to net_device structure |
| 739 |
* |
| 740 |
* Return: 0 on success, -ENOSPC if FIFO is full. |
| 741 |
*/ |
| 742 |
static int xcan_start_xmit_fifo(struct sk_buff *skb, struct net_device *ndev) |
| 743 |
{ |
| 744 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 745 |
unsigned long flags; |
| 746 |
|
| 747 |
/* Check if the TX buffer is full */ |
| 748 |
if (unlikely(priv->read_reg(priv, XCAN_SR_OFFSET) & |
| 749 |
XCAN_SR_TXFLL_MASK)) |
| 750 |
return -ENOSPC; |
| 751 |
|
| 752 |
spin_lock_irqsave(&priv->tx_lock, flags); |
| 753 |
|
| 754 |
xcan_write_frame(ndev, skb, XCAN_TXFIFO_OFFSET); |
| 755 |
|
| 756 |
/* Clear TX-FIFO-empty interrupt for xcan_tx_interrupt() */ |
| 757 |
if (priv->tx_max > 1) |
| 758 |
priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_TXFEMP_MASK); |
| 759 |
|
| 760 |
/* Check if the TX buffer is full */ |
| 761 |
if ((priv->tx_head - priv->tx_tail) == priv->tx_max) |
| 762 |
netif_stop_queue(ndev); |
| 763 |
|
| 764 |
spin_unlock_irqrestore(&priv->tx_lock, flags); |
| 765 |
|
| 766 |
return 0; |
| 767 |
} |
| 768 |
|
| 769 |
/** |
| 770 |
* xcan_start_xmit_mailbox - Starts the transmission (mailbox mode) |
| 771 |
* @skb: sk_buff pointer that contains data to be Txed |
| 772 |
* @ndev: Pointer to net_device structure |
| 773 |
* |
| 774 |
* Return: 0 on success, -ENOSPC if there is no space |
| 775 |
*/ |
| 776 |
static int xcan_start_xmit_mailbox(struct sk_buff *skb, struct net_device *ndev) |
| 777 |
{ |
| 778 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 779 |
unsigned long flags; |
| 780 |
|
| 781 |
if (unlikely(priv->read_reg(priv, XCAN_TRR_OFFSET) & |
| 782 |
BIT(XCAN_TX_MAILBOX_IDX))) |
| 783 |
return -ENOSPC; |
| 784 |
|
| 785 |
spin_lock_irqsave(&priv->tx_lock, flags); |
| 786 |
|
| 787 |
xcan_write_frame(ndev, skb, |
| 788 |
XCAN_TXMSG_FRAME_OFFSET(XCAN_TX_MAILBOX_IDX)); |
| 789 |
|
| 790 |
/* Mark buffer as ready for transmit */ |
| 791 |
priv->write_reg(priv, XCAN_TRR_OFFSET, BIT(XCAN_TX_MAILBOX_IDX)); |
| 792 |
|
| 793 |
netif_stop_queue(ndev); |
| 794 |
|
| 795 |
spin_unlock_irqrestore(&priv->tx_lock, flags); |
| 796 |
|
| 797 |
return 0; |
| 798 |
} |
| 799 |
|
| 800 |
/** |
| 801 |
* xcan_start_xmit - Starts the transmission |
| 802 |
* @skb: sk_buff pointer that contains data to be Txed |
| 803 |
* @ndev: Pointer to net_device structure |
| 804 |
* |
| 805 |
* This function is invoked from upper layers to initiate transmission. |
| 806 |
* |
| 807 |
* Return: NETDEV_TX_OK on success and NETDEV_TX_BUSY when the tx queue is full |
| 808 |
*/ |
| 809 |
static netdev_tx_t xcan_start_xmit(struct sk_buff *skb, struct net_device *ndev) |
| 810 |
{ |
| 811 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 812 |
int ret; |
| 813 |
|
| 814 |
if (can_dev_dropped_skb(ndev, skb)) |
| 815 |
return NETDEV_TX_OK; |
| 816 |
|
| 817 |
if (priv->devtype.flags & XCAN_FLAG_TX_MAILBOXES) |
| 818 |
ret = xcan_start_xmit_mailbox(skb, ndev); |
| 819 |
else |
| 820 |
ret = xcan_start_xmit_fifo(skb, ndev); |
| 821 |
|
| 822 |
if (ret < 0) { |
| 823 |
netdev_err(ndev, "BUG!, TX full when queue awake!\n"); |
| 824 |
netif_stop_queue(ndev); |
| 825 |
return NETDEV_TX_BUSY; |
| 826 |
} |
| 827 |
|
| 828 |
return NETDEV_TX_OK; |
| 829 |
} |
| 830 |
|
| 831 |
/** |
| 832 |
* xcan_rx - Is called from CAN isr to complete the received |
| 833 |
* frame processing |
| 834 |
* @ndev: Pointer to net_device structure |
| 835 |
* @frame_base: Register offset to the frame to be read |
| 836 |
* |
| 837 |
* This function is invoked from the CAN isr(poll) to process the Rx frames. It |
| 838 |
* does minimal processing and invokes "netif_receive_skb" to complete further |
| 839 |
* processing. |
| 840 |
* Return: 1 on success and 0 on failure. |
| 841 |
*/ |
| 842 |
static int xcan_rx(struct net_device *ndev, int frame_base) |
| 843 |
{ |
| 844 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 845 |
struct net_device_stats *stats = &ndev->stats; |
| 846 |
struct can_frame *cf; |
| 847 |
struct sk_buff *skb; |
| 848 |
u32 id_xcan, dlc, data[2] = {0, 0}; |
| 849 |
|
| 850 |
skb = alloc_can_skb(ndev, &cf); |
| 851 |
if (unlikely(!skb)) { |
| 852 |
stats->rx_dropped++; |
| 853 |
return 0; |
| 854 |
} |
| 855 |
|
| 856 |
/* Read a frame from Xilinx zynq CANPS */ |
| 857 |
id_xcan = priv->read_reg(priv, XCAN_FRAME_ID_OFFSET(frame_base)); |
| 858 |
dlc = priv->read_reg(priv, XCAN_FRAME_DLC_OFFSET(frame_base)) >> |
| 859 |
XCAN_DLCR_DLC_SHIFT; |
| 860 |
|
| 861 |
/* Change Xilinx CAN data length format to socketCAN data format */ |
| 862 |
cf->len = can_cc_dlc2len(dlc); |
| 863 |
|
| 864 |
/* Change Xilinx CAN ID format to socketCAN ID format */ |
| 865 |
if (id_xcan & XCAN_IDR_IDE_MASK) { |
| 866 |
/* The received frame is an Extended format frame */ |
| 867 |
cf->can_id = (id_xcan & XCAN_IDR_ID1_MASK) >> 3; |
| 868 |
cf->can_id |= (id_xcan & XCAN_IDR_ID2_MASK) >> |
| 869 |
XCAN_IDR_ID2_SHIFT; |
| 870 |
cf->can_id |= CAN_EFF_FLAG; |
| 871 |
if (id_xcan & XCAN_IDR_RTR_MASK) |
| 872 |
cf->can_id |= CAN_RTR_FLAG; |
| 873 |
} else { |
| 874 |
/* The received frame is a standard format frame */ |
| 875 |
cf->can_id = (id_xcan & XCAN_IDR_ID1_MASK) >> |
| 876 |
XCAN_IDR_ID1_SHIFT; |
| 877 |
if (id_xcan & XCAN_IDR_SRR_MASK) |
| 878 |
cf->can_id |= CAN_RTR_FLAG; |
| 879 |
} |
| 880 |
|
| 881 |
/* DW1/DW2 must always be read to remove message from RXFIFO */ |
| 882 |
data[0] = priv->read_reg(priv, XCAN_FRAME_DW1_OFFSET(frame_base)); |
| 883 |
data[1] = priv->read_reg(priv, XCAN_FRAME_DW2_OFFSET(frame_base)); |
| 884 |
|
| 885 |
if (!(cf->can_id & CAN_RTR_FLAG)) { |
| 886 |
/* Change Xilinx CAN data format to socketCAN data format */ |
| 887 |
if (cf->len > 0) |
| 888 |
*(__be32 *)(cf->data) = cpu_to_be32(data[0]); |
| 889 |
if (cf->len > 4) |
| 890 |
*(__be32 *)(cf->data + 4) = cpu_to_be32(data[1]); |
| 891 |
|
| 892 |
stats->rx_bytes += cf->len; |
| 893 |
} |
| 894 |
stats->rx_packets++; |
| 895 |
|
| 896 |
netif_receive_skb(skb); |
| 897 |
|
| 898 |
return 1; |
| 899 |
} |
| 900 |
|
| 901 |
/** |
| 902 |
* xcanfd_rx - Is called from CAN isr to complete the received |
| 903 |
* frame processing |
| 904 |
* @ndev: Pointer to net_device structure |
| 905 |
* @frame_base: Register offset to the frame to be read |
| 906 |
* |
| 907 |
* This function is invoked from the CAN isr(poll) to process the Rx frames. It |
| 908 |
* does minimal processing and invokes "netif_receive_skb" to complete further |
| 909 |
* processing. |
| 910 |
* Return: 1 on success and 0 on failure. |
| 911 |
*/ |
| 912 |
static int xcanfd_rx(struct net_device *ndev, int frame_base) |
| 913 |
{ |
| 914 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 915 |
struct net_device_stats *stats = &ndev->stats; |
| 916 |
struct canfd_frame *cf; |
| 917 |
struct sk_buff *skb; |
| 918 |
u32 id_xcan, dlc, data[2] = {0, 0}, dwindex = 0, i, dw_offset; |
| 919 |
|
| 920 |
id_xcan = priv->read_reg(priv, XCAN_FRAME_ID_OFFSET(frame_base)); |
| 921 |
dlc = priv->read_reg(priv, XCAN_FRAME_DLC_OFFSET(frame_base)); |
| 922 |
if (dlc & XCAN_DLCR_EDL_MASK) |
| 923 |
skb = alloc_canfd_skb(ndev, &cf); |
| 924 |
else |
| 925 |
skb = alloc_can_skb(ndev, (struct can_frame **)&cf); |
| 926 |
|
| 927 |
if (unlikely(!skb)) { |
| 928 |
stats->rx_dropped++; |
| 929 |
return 0; |
| 930 |
} |
| 931 |
|
| 932 |
/* Change Xilinx CANFD data length format to socketCAN data |
| 933 |
* format |
| 934 |
*/ |
| 935 |
if (dlc & XCAN_DLCR_EDL_MASK) |
| 936 |
cf->len = can_fd_dlc2len((dlc & XCAN_DLCR_DLC_MASK) >> |
| 937 |
XCAN_DLCR_DLC_SHIFT); |
| 938 |
else |
| 939 |
cf->len = can_cc_dlc2len((dlc & XCAN_DLCR_DLC_MASK) >> |
| 940 |
XCAN_DLCR_DLC_SHIFT); |
| 941 |
|
| 942 |
/* Change Xilinx CAN ID format to socketCAN ID format */ |
| 943 |
if (id_xcan & XCAN_IDR_IDE_MASK) { |
| 944 |
/* The received frame is an Extended format frame */ |
| 945 |
cf->can_id = (id_xcan & XCAN_IDR_ID1_MASK) >> 3; |
| 946 |
cf->can_id |= (id_xcan & XCAN_IDR_ID2_MASK) >> |
| 947 |
XCAN_IDR_ID2_SHIFT; |
| 948 |
cf->can_id |= CAN_EFF_FLAG; |
| 949 |
if (id_xcan & XCAN_IDR_RTR_MASK) |
| 950 |
cf->can_id |= CAN_RTR_FLAG; |
| 951 |
} else { |
| 952 |
/* The received frame is a standard format frame */ |
| 953 |
cf->can_id = (id_xcan & XCAN_IDR_ID1_MASK) >> |
| 954 |
XCAN_IDR_ID1_SHIFT; |
| 955 |
if (!(dlc & XCAN_DLCR_EDL_MASK) && (id_xcan & |
| 956 |
XCAN_IDR_SRR_MASK)) |
| 957 |
cf->can_id |= CAN_RTR_FLAG; |
| 958 |
} |
| 959 |
|
| 960 |
/* Check the frame received is FD or not*/ |
| 961 |
if (dlc & XCAN_DLCR_EDL_MASK) { |
| 962 |
for (i = 0; i < cf->len; i += 4) { |
| 963 |
dw_offset = XCANFD_FRAME_DW_OFFSET(frame_base) + |
| 964 |
(dwindex * XCANFD_DW_BYTES); |
| 965 |
data[0] = priv->read_reg(priv, dw_offset); |
| 966 |
*(__be32 *)(cf->data + i) = cpu_to_be32(data[0]); |
| 967 |
dwindex++; |
| 968 |
} |
| 969 |
} else { |
| 970 |
for (i = 0; i < cf->len; i += 4) { |
| 971 |
dw_offset = XCANFD_FRAME_DW_OFFSET(frame_base); |
| 972 |
data[0] = priv->read_reg(priv, dw_offset + i); |
| 973 |
*(__be32 *)(cf->data + i) = cpu_to_be32(data[0]); |
| 974 |
} |
| 975 |
} |
| 976 |
|
| 977 |
if (!(cf->can_id & CAN_RTR_FLAG)) |
| 978 |
stats->rx_bytes += cf->len; |
| 979 |
stats->rx_packets++; |
| 980 |
|
| 981 |
netif_receive_skb(skb); |
| 982 |
|
| 983 |
return 1; |
| 984 |
} |
| 985 |
|
| 986 |
/** |
| 987 |
* xcan_current_error_state - Get current error state from HW |
| 988 |
* @ndev: Pointer to net_device structure |
| 989 |
* |
| 990 |
* Checks the current CAN error state from the HW. Note that this |
| 991 |
* only checks for ERROR_PASSIVE and ERROR_WARNING. |
| 992 |
* |
| 993 |
* Return: |
| 994 |
* ERROR_PASSIVE or ERROR_WARNING if either is active, ERROR_ACTIVE |
| 995 |
* otherwise. |
| 996 |
*/ |
| 997 |
static enum can_state xcan_current_error_state(struct net_device *ndev) |
| 998 |
{ |
| 999 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1000 |
u32 status = priv->read_reg(priv, XCAN_SR_OFFSET); |
| 1001 |
|
| 1002 |
if ((status & XCAN_SR_ESTAT_MASK) == XCAN_SR_ESTAT_MASK) |
| 1003 |
return CAN_STATE_ERROR_PASSIVE; |
| 1004 |
else if (status & XCAN_SR_ERRWRN_MASK) |
| 1005 |
return CAN_STATE_ERROR_WARNING; |
| 1006 |
else |
| 1007 |
return CAN_STATE_ERROR_ACTIVE; |
| 1008 |
} |
| 1009 |
|
| 1010 |
/** |
| 1011 |
* xcan_set_error_state - Set new CAN error state |
| 1012 |
* @ndev: Pointer to net_device structure |
| 1013 |
* @new_state: The new CAN state to be set |
| 1014 |
* @cf: Error frame to be populated or NULL |
| 1015 |
* |
| 1016 |
* Set new CAN error state for the device, updating statistics and |
| 1017 |
* populating the error frame if given. |
| 1018 |
*/ |
| 1019 |
static void xcan_set_error_state(struct net_device *ndev, |
| 1020 |
enum can_state new_state, |
| 1021 |
struct can_frame *cf) |
| 1022 |
{ |
| 1023 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1024 |
u32 ecr = priv->read_reg(priv, XCAN_ECR_OFFSET); |
| 1025 |
u32 txerr = ecr & XCAN_ECR_TEC_MASK; |
| 1026 |
u32 rxerr = (ecr & XCAN_ECR_REC_MASK) >> XCAN_ESR_REC_SHIFT; |
| 1027 |
enum can_state tx_state = txerr >= rxerr ? new_state : 0; |
| 1028 |
enum can_state rx_state = txerr <= rxerr ? new_state : 0; |
| 1029 |
|
| 1030 |
/* non-ERROR states are handled elsewhere */ |
| 1031 |
if (WARN_ON(new_state > CAN_STATE_ERROR_PASSIVE)) |
| 1032 |
return; |
| 1033 |
|
| 1034 |
can_change_state(ndev, cf, tx_state, rx_state); |
| 1035 |
|
| 1036 |
if (cf) { |
| 1037 |
cf->can_id |= CAN_ERR_CNT; |
| 1038 |
cf->data[6] = txerr; |
| 1039 |
cf->data[7] = rxerr; |
| 1040 |
} |
| 1041 |
} |
| 1042 |
|
| 1043 |
/** |
| 1044 |
* xcan_update_error_state_after_rxtx - Update CAN error state after RX/TX |
| 1045 |
* @ndev: Pointer to net_device structure |
| 1046 |
* |
| 1047 |
* If the device is in a ERROR-WARNING or ERROR-PASSIVE state, check if |
| 1048 |
* the performed RX/TX has caused it to drop to a lesser state and set |
| 1049 |
* the interface state accordingly. |
| 1050 |
*/ |
| 1051 |
static void xcan_update_error_state_after_rxtx(struct net_device *ndev) |
| 1052 |
{ |
| 1053 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1054 |
enum can_state old_state = priv->can.state; |
| 1055 |
enum can_state new_state; |
| 1056 |
|
| 1057 |
/* changing error state due to successful frame RX/TX can only |
| 1058 |
* occur from these states |
| 1059 |
*/ |
| 1060 |
if (old_state != CAN_STATE_ERROR_WARNING && |
| 1061 |
old_state != CAN_STATE_ERROR_PASSIVE) |
| 1062 |
return; |
| 1063 |
|
| 1064 |
new_state = xcan_current_error_state(ndev); |
| 1065 |
|
| 1066 |
if (new_state != old_state) { |
| 1067 |
struct sk_buff *skb; |
| 1068 |
struct can_frame *cf; |
| 1069 |
|
| 1070 |
skb = alloc_can_err_skb(ndev, &cf); |
| 1071 |
|
| 1072 |
xcan_set_error_state(ndev, new_state, skb ? cf : NULL); |
| 1073 |
|
| 1074 |
if (skb) |
| 1075 |
netif_rx(skb); |
| 1076 |
} |
| 1077 |
} |
| 1078 |
|
| 1079 |
/** |
| 1080 |
* xcan_err_interrupt - error frame Isr |
| 1081 |
* @ndev: net_device pointer |
| 1082 |
* @isr: interrupt status register value |
| 1083 |
* |
| 1084 |
* This is the CAN error interrupt and it will |
| 1085 |
* check the type of error and forward the error |
| 1086 |
* frame to upper layers. |
| 1087 |
*/ |
| 1088 |
static void xcan_err_interrupt(struct net_device *ndev, u32 isr) |
| 1089 |
{ |
| 1090 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1091 |
struct net_device_stats *stats = &ndev->stats; |
| 1092 |
struct can_frame cf = { }; |
| 1093 |
u32 err_status; |
| 1094 |
|
| 1095 |
err_status = priv->read_reg(priv, XCAN_ESR_OFFSET); |
| 1096 |
priv->write_reg(priv, XCAN_ESR_OFFSET, err_status); |
| 1097 |
|
| 1098 |
if (isr & XCAN_IXR_BSOFF_MASK) { |
| 1099 |
priv->can.state = CAN_STATE_BUS_OFF; |
| 1100 |
priv->can.can_stats.bus_off++; |
| 1101 |
/* Leave device in Config Mode in bus-off state */ |
| 1102 |
priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_RESET_MASK); |
| 1103 |
can_bus_off(ndev); |
| 1104 |
cf.can_id |= CAN_ERR_BUSOFF; |
| 1105 |
} else { |
| 1106 |
enum can_state new_state = xcan_current_error_state(ndev); |
| 1107 |
|
| 1108 |
if (new_state != priv->can.state) |
| 1109 |
xcan_set_error_state(ndev, new_state, &cf); |
| 1110 |
} |
| 1111 |
|
| 1112 |
/* Check for Arbitration lost interrupt */ |
| 1113 |
if (isr & XCAN_IXR_ARBLST_MASK) { |
| 1114 |
priv->can.can_stats.arbitration_lost++; |
| 1115 |
cf.can_id |= CAN_ERR_LOSTARB; |
| 1116 |
cf.data[0] = CAN_ERR_LOSTARB_UNSPEC; |
| 1117 |
} |
| 1118 |
|
| 1119 |
/* Check for RX FIFO Overflow interrupt */ |
| 1120 |
if (isr & XCAN_IXR_RXOFLW_MASK) { |
| 1121 |
stats->rx_over_errors++; |
| 1122 |
stats->rx_errors++; |
| 1123 |
cf.can_id |= CAN_ERR_CRTL; |
| 1124 |
cf.data[1] |= CAN_ERR_CRTL_RX_OVERFLOW; |
| 1125 |
} |
| 1126 |
|
| 1127 |
/* Check for RX Match Not Finished interrupt */ |
| 1128 |
if (isr & XCAN_IXR_RXMNF_MASK) { |
| 1129 |
stats->rx_dropped++; |
| 1130 |
stats->rx_errors++; |
| 1131 |
netdev_err(ndev, "RX match not finished, frame discarded\n"); |
| 1132 |
cf.can_id |= CAN_ERR_CRTL; |
| 1133 |
cf.data[1] |= CAN_ERR_CRTL_UNSPEC; |
| 1134 |
} |
| 1135 |
|
| 1136 |
/* Check for error interrupt */ |
| 1137 |
if (isr & XCAN_IXR_ERROR_MASK) { |
| 1138 |
bool berr_reporting = false; |
| 1139 |
|
| 1140 |
if (priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING) { |
| 1141 |
berr_reporting = true; |
| 1142 |
cf.can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; |
| 1143 |
} |
| 1144 |
|
| 1145 |
/* Check for Ack error interrupt */ |
| 1146 |
if (err_status & XCAN_ESR_ACKER_MASK) { |
| 1147 |
stats->tx_errors++; |
| 1148 |
if (berr_reporting) { |
| 1149 |
cf.can_id |= CAN_ERR_ACK; |
| 1150 |
cf.data[3] = CAN_ERR_PROT_LOC_ACK; |
| 1151 |
} |
| 1152 |
} |
| 1153 |
|
| 1154 |
/* Check for Bit error interrupt */ |
| 1155 |
if (err_status & XCAN_ESR_BERR_MASK) { |
| 1156 |
stats->tx_errors++; |
| 1157 |
if (berr_reporting) { |
| 1158 |
cf.can_id |= CAN_ERR_PROT; |
| 1159 |
cf.data[2] = CAN_ERR_PROT_BIT; |
| 1160 |
} |
| 1161 |
} |
| 1162 |
|
| 1163 |
/* Check for Stuff error interrupt */ |
| 1164 |
if (err_status & XCAN_ESR_STER_MASK) { |
| 1165 |
stats->rx_errors++; |
| 1166 |
if (berr_reporting) { |
| 1167 |
cf.can_id |= CAN_ERR_PROT; |
| 1168 |
cf.data[2] = CAN_ERR_PROT_STUFF; |
| 1169 |
} |
| 1170 |
} |
| 1171 |
|
| 1172 |
/* Check for Form error interrupt */ |
| 1173 |
if (err_status & XCAN_ESR_FMER_MASK) { |
| 1174 |
stats->rx_errors++; |
| 1175 |
if (berr_reporting) { |
| 1176 |
cf.can_id |= CAN_ERR_PROT; |
| 1177 |
cf.data[2] = CAN_ERR_PROT_FORM; |
| 1178 |
} |
| 1179 |
} |
| 1180 |
|
| 1181 |
/* Check for CRC error interrupt */ |
| 1182 |
if (err_status & XCAN_ESR_CRCER_MASK) { |
| 1183 |
stats->rx_errors++; |
| 1184 |
if (berr_reporting) { |
| 1185 |
cf.can_id |= CAN_ERR_PROT; |
| 1186 |
cf.data[3] = CAN_ERR_PROT_LOC_CRC_SEQ; |
| 1187 |
} |
| 1188 |
} |
| 1189 |
priv->can.can_stats.bus_error++; |
| 1190 |
} |
| 1191 |
|
| 1192 |
if (priv->ecc_enable && isr & XCAN_IXR_ECC_MASK) { |
| 1193 |
u32 reg_rx_ecc, reg_txol_ecc, reg_txtl_ecc; |
| 1194 |
|
| 1195 |
reg_rx_ecc = priv->read_reg(priv, XCAN_RXFIFO_ECC_OFFSET); |
| 1196 |
reg_txol_ecc = priv->read_reg(priv, XCAN_TXOLFIFO_ECC_OFFSET); |
| 1197 |
reg_txtl_ecc = priv->read_reg(priv, XCAN_TXTLFIFO_ECC_OFFSET); |
| 1198 |
|
| 1199 |
/* The counter reaches its maximum at 0xffff and does not overflow. |
| 1200 |
* Accept the small race window between reading and resetting ECC counters. |
| 1201 |
*/ |
| 1202 |
priv->write_reg(priv, XCAN_ECC_CFG_OFFSET, XCAN_ECC_CFG_REECRX_MASK | |
| 1203 |
XCAN_ECC_CFG_REECTXOL_MASK | XCAN_ECC_CFG_REECTXTL_MASK); |
| 1204 |
|
| 1205 |
u64_stats_update_begin(&priv->syncp); |
| 1206 |
|
| 1207 |
if (isr & XCAN_IXR_E2BERX_MASK) { |
| 1208 |
u64_stats_add(&priv->ecc_rx_2_bit_errors, |
| 1209 |
FIELD_GET(XCAN_ECC_2BIT_CNT_MASK, reg_rx_ecc)); |
| 1210 |
} |
| 1211 |
|
| 1212 |
if (isr & XCAN_IXR_E1BERX_MASK) { |
| 1213 |
u64_stats_add(&priv->ecc_rx_1_bit_errors, |
| 1214 |
FIELD_GET(XCAN_ECC_1BIT_CNT_MASK, reg_rx_ecc)); |
| 1215 |
} |
| 1216 |
|
| 1217 |
if (isr & XCAN_IXR_E2BETXOL_MASK) { |
| 1218 |
u64_stats_add(&priv->ecc_txol_2_bit_errors, |
| 1219 |
FIELD_GET(XCAN_ECC_2BIT_CNT_MASK, reg_txol_ecc)); |
| 1220 |
} |
| 1221 |
|
| 1222 |
if (isr & XCAN_IXR_E1BETXOL_MASK) { |
| 1223 |
u64_stats_add(&priv->ecc_txol_1_bit_errors, |
| 1224 |
FIELD_GET(XCAN_ECC_1BIT_CNT_MASK, reg_txol_ecc)); |
| 1225 |
} |
| 1226 |
|
| 1227 |
if (isr & XCAN_IXR_E2BETXTL_MASK) { |
| 1228 |
u64_stats_add(&priv->ecc_txtl_2_bit_errors, |
| 1229 |
FIELD_GET(XCAN_ECC_2BIT_CNT_MASK, reg_txtl_ecc)); |
| 1230 |
} |
| 1231 |
|
| 1232 |
if (isr & XCAN_IXR_E1BETXTL_MASK) { |
| 1233 |
u64_stats_add(&priv->ecc_txtl_1_bit_errors, |
| 1234 |
FIELD_GET(XCAN_ECC_1BIT_CNT_MASK, reg_txtl_ecc)); |
| 1235 |
} |
| 1236 |
|
| 1237 |
u64_stats_update_end(&priv->syncp); |
| 1238 |
} |
| 1239 |
|
| 1240 |
if (cf.can_id) { |
| 1241 |
struct can_frame *skb_cf; |
| 1242 |
struct sk_buff *skb = alloc_can_err_skb(ndev, &skb_cf); |
| 1243 |
|
| 1244 |
if (skb) { |
| 1245 |
skb_cf->can_id |= cf.can_id; |
| 1246 |
memcpy(skb_cf->data, cf.data, CAN_ERR_DLC); |
| 1247 |
netif_rx(skb); |
| 1248 |
} |
| 1249 |
} |
| 1250 |
|
| 1251 |
netdev_dbg(ndev, "%s: error status register:0x%x\n", |
| 1252 |
__func__, priv->read_reg(priv, XCAN_ESR_OFFSET)); |
| 1253 |
} |
| 1254 |
|
| 1255 |
/** |
| 1256 |
* xcan_state_interrupt - It will check the state of the CAN device |
| 1257 |
* @ndev: net_device pointer |
| 1258 |
* @isr: interrupt status register value |
| 1259 |
* |
| 1260 |
* This will checks the state of the CAN device |
| 1261 |
* and puts the device into appropriate state. |
| 1262 |
*/ |
| 1263 |
static void xcan_state_interrupt(struct net_device *ndev, u32 isr) |
| 1264 |
{ |
| 1265 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1266 |
|
| 1267 |
/* Check for Sleep interrupt if set put CAN device in sleep state */ |
| 1268 |
if (isr & XCAN_IXR_SLP_MASK) |
| 1269 |
priv->can.state = CAN_STATE_SLEEPING; |
| 1270 |
|
| 1271 |
/* Check for Wake up interrupt if set put CAN device in Active state */ |
| 1272 |
if (isr & XCAN_IXR_WKUP_MASK) |
| 1273 |
priv->can.state = CAN_STATE_ERROR_ACTIVE; |
| 1274 |
} |
| 1275 |
|
| 1276 |
/** |
| 1277 |
* xcan_rx_fifo_get_next_frame - Get register offset of next RX frame |
| 1278 |
* @priv: Driver private data structure |
| 1279 |
* |
| 1280 |
* Return: Register offset of the next frame in RX FIFO. |
| 1281 |
*/ |
| 1282 |
static int xcan_rx_fifo_get_next_frame(struct xcan_priv *priv) |
| 1283 |
{ |
| 1284 |
int offset; |
| 1285 |
|
| 1286 |
if (priv->devtype.flags & XCAN_FLAG_RX_FIFO_MULTI) { |
| 1287 |
u32 fsr, mask; |
| 1288 |
|
| 1289 |
/* clear RXOK before the is-empty check so that any newly |
| 1290 |
* received frame will reassert it without a race |
| 1291 |
*/ |
| 1292 |
priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_RXOK_MASK); |
| 1293 |
|
| 1294 |
fsr = priv->read_reg(priv, XCAN_FSR_OFFSET); |
| 1295 |
|
| 1296 |
/* check if RX FIFO is empty */ |
| 1297 |
if (priv->devtype.flags & XCAN_FLAG_CANFD_2) |
| 1298 |
mask = XCAN_2_FSR_FL_MASK; |
| 1299 |
else |
| 1300 |
mask = XCAN_FSR_FL_MASK; |
| 1301 |
|
| 1302 |
if (!(fsr & mask)) |
| 1303 |
return -ENOENT; |
| 1304 |
|
| 1305 |
if (priv->devtype.flags & XCAN_FLAG_CANFD_2) |
| 1306 |
offset = |
| 1307 |
XCAN_RXMSG_2_FRAME_OFFSET(fsr & XCAN_2_FSR_RI_MASK); |
| 1308 |
else |
| 1309 |
offset = |
| 1310 |
XCAN_RXMSG_FRAME_OFFSET(fsr & XCAN_FSR_RI_MASK); |
| 1311 |
|
| 1312 |
} else { |
| 1313 |
/* check if RX FIFO is empty */ |
| 1314 |
if (!(priv->read_reg(priv, XCAN_ISR_OFFSET) & |
| 1315 |
XCAN_IXR_RXNEMP_MASK)) |
| 1316 |
return -ENOENT; |
| 1317 |
|
| 1318 |
/* frames are read from a static offset */ |
| 1319 |
offset = XCAN_RXFIFO_OFFSET; |
| 1320 |
} |
| 1321 |
|
| 1322 |
return offset; |
| 1323 |
} |
| 1324 |
|
| 1325 |
/** |
| 1326 |
* xcan_rx_poll - Poll routine for rx packets (NAPI) |
| 1327 |
* @napi: napi structure pointer |
| 1328 |
* @quota: Max number of rx packets to be processed. |
| 1329 |
* |
| 1330 |
* This is the poll routine for rx part. |
| 1331 |
* It will process the packets maximux quota value. |
| 1332 |
* |
| 1333 |
* Return: number of packets received |
| 1334 |
*/ |
| 1335 |
static int xcan_rx_poll(struct napi_struct *napi, int quota) |
| 1336 |
{ |
| 1337 |
struct net_device *ndev = napi->dev; |
| 1338 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1339 |
u32 ier; |
| 1340 |
int work_done = 0; |
| 1341 |
int frame_offset; |
| 1342 |
|
| 1343 |
while ((frame_offset = xcan_rx_fifo_get_next_frame(priv)) >= 0 && |
| 1344 |
(work_done < quota)) { |
| 1345 |
if (xcan_rx_int_mask(priv) & XCAN_IXR_RXOK_MASK) |
| 1346 |
work_done += xcanfd_rx(ndev, frame_offset); |
| 1347 |
else |
| 1348 |
work_done += xcan_rx(ndev, frame_offset); |
| 1349 |
|
| 1350 |
if (priv->devtype.flags & XCAN_FLAG_RX_FIFO_MULTI) |
| 1351 |
/* increment read index */ |
| 1352 |
priv->write_reg(priv, XCAN_FSR_OFFSET, |
| 1353 |
XCAN_FSR_IRI_MASK); |
| 1354 |
else |
| 1355 |
/* clear rx-not-empty (will actually clear only if |
| 1356 |
* empty) |
| 1357 |
*/ |
| 1358 |
priv->write_reg(priv, XCAN_ICR_OFFSET, |
| 1359 |
XCAN_IXR_RXNEMP_MASK); |
| 1360 |
} |
| 1361 |
|
| 1362 |
if (work_done) |
| 1363 |
xcan_update_error_state_after_rxtx(ndev); |
| 1364 |
|
| 1365 |
if (work_done < quota) { |
| 1366 |
if (napi_complete_done(napi, work_done)) { |
| 1367 |
ier = priv->read_reg(priv, XCAN_IER_OFFSET); |
| 1368 |
ier |= xcan_rx_int_mask(priv); |
| 1369 |
priv->write_reg(priv, XCAN_IER_OFFSET, ier); |
| 1370 |
} |
| 1371 |
} |
| 1372 |
return work_done; |
| 1373 |
} |
| 1374 |
|
| 1375 |
/** |
| 1376 |
* xcan_tx_interrupt - Tx Done Isr |
| 1377 |
* @ndev: net_device pointer |
| 1378 |
* @isr: Interrupt status register value |
| 1379 |
*/ |
| 1380 |
static void xcan_tx_interrupt(struct net_device *ndev, u32 isr) |
| 1381 |
{ |
| 1382 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1383 |
struct net_device_stats *stats = &ndev->stats; |
| 1384 |
unsigned int frames_in_fifo; |
| 1385 |
int frames_sent = 1; /* TXOK => at least 1 frame was sent */ |
| 1386 |
unsigned long flags; |
| 1387 |
int retries = 0; |
| 1388 |
|
| 1389 |
/* Synchronize with xmit as we need to know the exact number |
| 1390 |
* of frames in the FIFO to stay in sync due to the TXFEMP |
| 1391 |
* handling. |
| 1392 |
* This also prevents a race between netif_wake_queue() and |
| 1393 |
* netif_stop_queue(). |
| 1394 |
*/ |
| 1395 |
spin_lock_irqsave(&priv->tx_lock, flags); |
| 1396 |
|
| 1397 |
frames_in_fifo = priv->tx_head - priv->tx_tail; |
| 1398 |
|
| 1399 |
if (WARN_ON_ONCE(frames_in_fifo == 0)) { |
| 1400 |
/* clear TXOK anyway to avoid getting back here */ |
| 1401 |
priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_TXOK_MASK); |
| 1402 |
spin_unlock_irqrestore(&priv->tx_lock, flags); |
| 1403 |
return; |
| 1404 |
} |
| 1405 |
|
| 1406 |
/* Check if 2 frames were sent (TXOK only means that at least 1 |
| 1407 |
* frame was sent). |
| 1408 |
*/ |
| 1409 |
if (frames_in_fifo > 1) { |
| 1410 |
WARN_ON(frames_in_fifo > priv->tx_max); |
| 1411 |
|
| 1412 |
/* Synchronize TXOK and isr so that after the loop: |
| 1413 |
* (1) isr variable is up-to-date at least up to TXOK clear |
| 1414 |
* time. This avoids us clearing a TXOK of a second frame |
| 1415 |
* but not noticing that the FIFO is now empty and thus |
| 1416 |
* marking only a single frame as sent. |
| 1417 |
* (2) No TXOK is left. Having one could mean leaving a |
| 1418 |
* stray TXOK as we might process the associated frame |
| 1419 |
* via TXFEMP handling as we read TXFEMP *after* TXOK |
| 1420 |
* clear to satisfy (1). |
| 1421 |
*/ |
| 1422 |
while ((isr & XCAN_IXR_TXOK_MASK) && |
| 1423 |
!WARN_ON(++retries == 100)) { |
| 1424 |
priv->write_reg(priv, XCAN_ICR_OFFSET, |
| 1425 |
XCAN_IXR_TXOK_MASK); |
| 1426 |
isr = priv->read_reg(priv, XCAN_ISR_OFFSET); |
| 1427 |
} |
| 1428 |
|
| 1429 |
if (isr & XCAN_IXR_TXFEMP_MASK) { |
| 1430 |
/* nothing in FIFO anymore */ |
| 1431 |
frames_sent = frames_in_fifo; |
| 1432 |
} |
| 1433 |
} else { |
| 1434 |
/* single frame in fifo, just clear TXOK */ |
| 1435 |
priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_TXOK_MASK); |
| 1436 |
} |
| 1437 |
|
| 1438 |
while (frames_sent--) { |
| 1439 |
stats->tx_bytes += can_get_echo_skb(ndev, priv->tx_tail % |
| 1440 |
priv->tx_max, NULL); |
| 1441 |
priv->tx_tail++; |
| 1442 |
stats->tx_packets++; |
| 1443 |
} |
| 1444 |
|
| 1445 |
netif_wake_queue(ndev); |
| 1446 |
|
| 1447 |
spin_unlock_irqrestore(&priv->tx_lock, flags); |
| 1448 |
|
| 1449 |
xcan_update_error_state_after_rxtx(ndev); |
| 1450 |
} |
| 1451 |
|
| 1452 |
/** |
| 1453 |
* xcan_interrupt - CAN Isr |
| 1454 |
* @irq: irq number |
| 1455 |
* @dev_id: device id pointer |
| 1456 |
* |
| 1457 |
* This is the xilinx CAN Isr. It checks for the type of interrupt |
| 1458 |
* and invokes the corresponding ISR. |
| 1459 |
* |
| 1460 |
* Return: |
| 1461 |
* IRQ_NONE - If CAN device is in sleep mode, IRQ_HANDLED otherwise |
| 1462 |
*/ |
| 1463 |
static irqreturn_t xcan_interrupt(int irq, void *dev_id) |
| 1464 |
{ |
| 1465 |
struct net_device *ndev = (struct net_device *)dev_id; |
| 1466 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1467 |
u32 isr_errors, mask; |
| 1468 |
u32 isr, ier; |
| 1469 |
u32 rx_int_mask = xcan_rx_int_mask(priv); |
| 1470 |
|
| 1471 |
/* Get the interrupt status from Xilinx CAN */ |
| 1472 |
isr = priv->read_reg(priv, XCAN_ISR_OFFSET); |
| 1473 |
if (!isr) |
| 1474 |
return IRQ_NONE; |
| 1475 |
|
| 1476 |
/* Check for the type of interrupt and Processing it */ |
| 1477 |
if (isr & (XCAN_IXR_SLP_MASK | XCAN_IXR_WKUP_MASK)) { |
| 1478 |
priv->write_reg(priv, XCAN_ICR_OFFSET, (XCAN_IXR_SLP_MASK | |
| 1479 |
XCAN_IXR_WKUP_MASK)); |
| 1480 |
xcan_state_interrupt(ndev, isr); |
| 1481 |
} |
| 1482 |
|
| 1483 |
/* Check for Tx interrupt and Processing it */ |
| 1484 |
if (isr & XCAN_IXR_TXOK_MASK) |
| 1485 |
xcan_tx_interrupt(ndev, isr); |
| 1486 |
|
| 1487 |
mask = XCAN_IXR_ERROR_MASK | XCAN_IXR_RXOFLW_MASK | |
| 1488 |
XCAN_IXR_BSOFF_MASK | XCAN_IXR_ARBLST_MASK | |
| 1489 |
XCAN_IXR_RXMNF_MASK; |
| 1490 |
|
| 1491 |
if (priv->ecc_enable) |
| 1492 |
mask |= XCAN_IXR_ECC_MASK; |
| 1493 |
|
| 1494 |
/* Check for the type of error interrupt and Processing it */ |
| 1495 |
isr_errors = isr & mask; |
| 1496 |
if (isr_errors) { |
| 1497 |
priv->write_reg(priv, XCAN_ICR_OFFSET, isr_errors); |
| 1498 |
xcan_err_interrupt(ndev, isr); |
| 1499 |
} |
| 1500 |
|
| 1501 |
/* Check for the type of receive interrupt and Processing it */ |
| 1502 |
if (isr & rx_int_mask) { |
| 1503 |
ier = priv->read_reg(priv, XCAN_IER_OFFSET); |
| 1504 |
ier &= ~rx_int_mask; |
| 1505 |
priv->write_reg(priv, XCAN_IER_OFFSET, ier); |
| 1506 |
napi_schedule(&priv->napi); |
| 1507 |
} |
| 1508 |
return IRQ_HANDLED; |
| 1509 |
} |
| 1510 |
|
| 1511 |
/** |
| 1512 |
* xcan_chip_stop - Driver stop routine |
| 1513 |
* @ndev: Pointer to net_device structure |
| 1514 |
* |
| 1515 |
* This is the drivers stop routine. It will disable the |
| 1516 |
* interrupts and put the device into configuration mode. |
| 1517 |
*/ |
| 1518 |
static void xcan_chip_stop(struct net_device *ndev) |
| 1519 |
{ |
| 1520 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1521 |
int ret; |
| 1522 |
|
| 1523 |
/* Disable interrupts and leave the can in configuration mode */ |
| 1524 |
ret = set_reset_mode(ndev); |
| 1525 |
if (ret < 0) |
| 1526 |
netdev_dbg(ndev, "set_reset_mode() Failed\n"); |
| 1527 |
|
| 1528 |
priv->can.state = CAN_STATE_STOPPED; |
| 1529 |
} |
| 1530 |
|
| 1531 |
/** |
| 1532 |
* xcan_open - Driver open routine |
| 1533 |
* @ndev: Pointer to net_device structure |
| 1534 |
* |
| 1535 |
* This is the driver open routine. |
| 1536 |
* Return: 0 on success and failure value on error |
| 1537 |
*/ |
| 1538 |
static int xcan_open(struct net_device *ndev) |
| 1539 |
{ |
| 1540 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1541 |
int ret; |
| 1542 |
|
| 1543 |
ret = phy_power_on(priv->transceiver); |
| 1544 |
if (ret) |
| 1545 |
return ret; |
| 1546 |
|
| 1547 |
ret = pm_runtime_get_sync(priv->dev); |
| 1548 |
if (ret < 0) { |
| 1549 |
netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n", |
| 1550 |
__func__, ret); |
| 1551 |
goto err; |
| 1552 |
} |
| 1553 |
|
| 1554 |
ret = request_irq(ndev->irq, xcan_interrupt, priv->irq_flags, |
| 1555 |
ndev->name, ndev); |
| 1556 |
if (ret < 0) { |
| 1557 |
netdev_err(ndev, "irq allocation for CAN failed\n"); |
| 1558 |
goto err; |
| 1559 |
} |
| 1560 |
|
| 1561 |
/* Set chip into reset mode */ |
| 1562 |
ret = set_reset_mode(ndev); |
| 1563 |
if (ret < 0) { |
| 1564 |
netdev_err(ndev, "mode resetting failed!\n"); |
| 1565 |
goto err_irq; |
| 1566 |
} |
| 1567 |
|
| 1568 |
/* Common open */ |
| 1569 |
ret = open_candev(ndev); |
| 1570 |
if (ret) |
| 1571 |
goto err_irq; |
| 1572 |
|
| 1573 |
ret = xcan_chip_start(ndev); |
| 1574 |
if (ret < 0) { |
| 1575 |
netdev_err(ndev, "xcan_chip_start failed!\n"); |
| 1576 |
goto err_candev; |
| 1577 |
} |
| 1578 |
|
| 1579 |
napi_enable(&priv->napi); |
| 1580 |
netif_start_queue(ndev); |
| 1581 |
|
| 1582 |
return 0; |
| 1583 |
|
| 1584 |
err_candev: |
| 1585 |
close_candev(ndev); |
| 1586 |
err_irq: |
| 1587 |
free_irq(ndev->irq, ndev); |
| 1588 |
err: |
| 1589 |
pm_runtime_put(priv->dev); |
| 1590 |
phy_power_off(priv->transceiver); |
| 1591 |
|
| 1592 |
return ret; |
| 1593 |
} |
| 1594 |
|
| 1595 |
/** |
| 1596 |
* xcan_close - Driver close routine |
| 1597 |
* @ndev: Pointer to net_device structure |
| 1598 |
* |
| 1599 |
* Return: 0 always |
| 1600 |
*/ |
| 1601 |
static int xcan_close(struct net_device *ndev) |
| 1602 |
{ |
| 1603 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1604 |
|
| 1605 |
netif_stop_queue(ndev); |
| 1606 |
napi_disable(&priv->napi); |
| 1607 |
xcan_chip_stop(ndev); |
| 1608 |
free_irq(ndev->irq, ndev); |
| 1609 |
close_candev(ndev); |
| 1610 |
|
| 1611 |
pm_runtime_put(priv->dev); |
| 1612 |
phy_power_off(priv->transceiver); |
| 1613 |
|
| 1614 |
return 0; |
| 1615 |
} |
| 1616 |
|
| 1617 |
/** |
| 1618 |
* xcan_get_berr_counter - error counter routine |
| 1619 |
* @ndev: Pointer to net_device structure |
| 1620 |
* @bec: Pointer to can_berr_counter structure |
| 1621 |
* |
| 1622 |
* This is the driver error counter routine. |
| 1623 |
* Return: 0 on success and failure value on error |
| 1624 |
*/ |
| 1625 |
static int xcan_get_berr_counter(const struct net_device *ndev, |
| 1626 |
struct can_berr_counter *bec) |
| 1627 |
{ |
| 1628 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1629 |
int ret; |
| 1630 |
|
| 1631 |
ret = pm_runtime_get_sync(priv->dev); |
| 1632 |
if (ret < 0) { |
| 1633 |
netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n", |
| 1634 |
__func__, ret); |
| 1635 |
pm_runtime_put(priv->dev); |
| 1636 |
return ret; |
| 1637 |
} |
| 1638 |
|
| 1639 |
bec->txerr = priv->read_reg(priv, XCAN_ECR_OFFSET) & XCAN_ECR_TEC_MASK; |
| 1640 |
bec->rxerr = ((priv->read_reg(priv, XCAN_ECR_OFFSET) & |
| 1641 |
XCAN_ECR_REC_MASK) >> XCAN_ESR_REC_SHIFT); |
| 1642 |
|
| 1643 |
pm_runtime_put(priv->dev); |
| 1644 |
|
| 1645 |
return 0; |
| 1646 |
} |
| 1647 |
|
| 1648 |
/** |
| 1649 |
* xcan_get_auto_tdcv - Get Transmitter Delay Compensation Value |
| 1650 |
* @ndev: Pointer to net_device structure |
| 1651 |
* @tdcv: Pointer to TDCV value |
| 1652 |
* |
| 1653 |
* Return: 0 on success |
| 1654 |
*/ |
| 1655 |
static int xcan_get_auto_tdcv(const struct net_device *ndev, u32 *tdcv) |
| 1656 |
{ |
| 1657 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1658 |
|
| 1659 |
*tdcv = FIELD_GET(XCAN_SR_TDCV_MASK, priv->read_reg(priv, XCAN_SR_OFFSET)); |
| 1660 |
|
| 1661 |
return 0; |
| 1662 |
} |
| 1663 |
|
| 1664 |
static void xcan_get_strings(struct net_device *ndev, u32 stringset, u8 *buf) |
| 1665 |
{ |
| 1666 |
switch (stringset) { |
| 1667 |
case ETH_SS_STATS: |
| 1668 |
memcpy(buf, &xcan_priv_flags_strings, |
| 1669 |
sizeof(xcan_priv_flags_strings)); |
| 1670 |
} |
| 1671 |
} |
| 1672 |
|
| 1673 |
static int xcan_get_sset_count(struct net_device *netdev, int sset) |
| 1674 |
{ |
| 1675 |
switch (sset) { |
| 1676 |
case ETH_SS_STATS: |
| 1677 |
return ARRAY_SIZE(xcan_priv_flags_strings); |
| 1678 |
default: |
| 1679 |
return -EOPNOTSUPP; |
| 1680 |
} |
| 1681 |
} |
| 1682 |
|
| 1683 |
static void xcan_get_ethtool_stats(struct net_device *ndev, |
| 1684 |
struct ethtool_stats *stats, u64 *data) |
| 1685 |
{ |
| 1686 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1687 |
unsigned int start; |
| 1688 |
|
| 1689 |
do { |
| 1690 |
start = u64_stats_fetch_begin(&priv->syncp); |
| 1691 |
|
| 1692 |
data[XCAN_ECC_RX_2_BIT_ERRORS] = u64_stats_read(&priv->ecc_rx_2_bit_errors); |
| 1693 |
data[XCAN_ECC_RX_1_BIT_ERRORS] = u64_stats_read(&priv->ecc_rx_1_bit_errors); |
| 1694 |
data[XCAN_ECC_TXOL_2_BIT_ERRORS] = u64_stats_read(&priv->ecc_txol_2_bit_errors); |
| 1695 |
data[XCAN_ECC_TXOL_1_BIT_ERRORS] = u64_stats_read(&priv->ecc_txol_1_bit_errors); |
| 1696 |
data[XCAN_ECC_TXTL_2_BIT_ERRORS] = u64_stats_read(&priv->ecc_txtl_2_bit_errors); |
| 1697 |
data[XCAN_ECC_TXTL_1_BIT_ERRORS] = u64_stats_read(&priv->ecc_txtl_1_bit_errors); |
| 1698 |
} while (u64_stats_fetch_retry(&priv->syncp, start)); |
| 1699 |
} |
| 1700 |
|
| 1701 |
static const struct net_device_ops xcan_netdev_ops = { |
| 1702 |
.ndo_open = xcan_open, |
| 1703 |
.ndo_stop = xcan_close, |
| 1704 |
.ndo_start_xmit = xcan_start_xmit, |
| 1705 |
}; |
| 1706 |
|
| 1707 |
static const struct ethtool_ops xcan_ethtool_ops = { |
| 1708 |
.get_ts_info = ethtool_op_get_ts_info, |
| 1709 |
.get_strings = xcan_get_strings, |
| 1710 |
.get_sset_count = xcan_get_sset_count, |
| 1711 |
.get_ethtool_stats = xcan_get_ethtool_stats, |
| 1712 |
}; |
| 1713 |
|
| 1714 |
/** |
| 1715 |
* xcan_suspend - Suspend method for the driver |
| 1716 |
* @dev: Address of the device structure |
| 1717 |
* |
| 1718 |
* Put the driver into low power mode. |
| 1719 |
* Return: 0 on success and failure value on error |
| 1720 |
*/ |
| 1721 |
static int __maybe_unused xcan_suspend(struct device *dev) |
| 1722 |
{ |
| 1723 |
struct net_device *ndev = dev_get_drvdata(dev); |
| 1724 |
|
| 1725 |
if (netif_running(ndev)) { |
| 1726 |
netif_stop_queue(ndev); |
| 1727 |
netif_device_detach(ndev); |
| 1728 |
xcan_chip_stop(ndev); |
| 1729 |
} |
| 1730 |
|
| 1731 |
return pm_runtime_force_suspend(dev); |
| 1732 |
} |
| 1733 |
|
| 1734 |
/** |
| 1735 |
* xcan_resume - Resume from suspend |
| 1736 |
* @dev: Address of the device structure |
| 1737 |
* |
| 1738 |
* Resume operation after suspend. |
| 1739 |
* Return: 0 on success and failure value on error |
| 1740 |
*/ |
| 1741 |
static int __maybe_unused xcan_resume(struct device *dev) |
| 1742 |
{ |
| 1743 |
struct net_device *ndev = dev_get_drvdata(dev); |
| 1744 |
int ret; |
| 1745 |
|
| 1746 |
ret = pm_runtime_force_resume(dev); |
| 1747 |
if (ret) { |
| 1748 |
dev_err(dev, "pm_runtime_force_resume failed on resume\n"); |
| 1749 |
return ret; |
| 1750 |
} |
| 1751 |
|
| 1752 |
if (netif_running(ndev)) { |
| 1753 |
ret = xcan_chip_start(ndev); |
| 1754 |
if (ret) { |
| 1755 |
dev_err(dev, "xcan_chip_start failed on resume\n"); |
| 1756 |
return ret; |
| 1757 |
} |
| 1758 |
|
| 1759 |
netif_device_attach(ndev); |
| 1760 |
netif_start_queue(ndev); |
| 1761 |
} |
| 1762 |
|
| 1763 |
return 0; |
| 1764 |
} |
| 1765 |
|
| 1766 |
/** |
| 1767 |
* xcan_runtime_suspend - Runtime suspend method for the driver |
| 1768 |
* @dev: Address of the device structure |
| 1769 |
* |
| 1770 |
* Put the driver into low power mode. |
| 1771 |
* Return: 0 always |
| 1772 |
*/ |
| 1773 |
static int __maybe_unused xcan_runtime_suspend(struct device *dev) |
| 1774 |
{ |
| 1775 |
struct net_device *ndev = dev_get_drvdata(dev); |
| 1776 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1777 |
|
| 1778 |
clk_disable_unprepare(priv->bus_clk); |
| 1779 |
clk_disable_unprepare(priv->can_clk); |
| 1780 |
|
| 1781 |
return 0; |
| 1782 |
} |
| 1783 |
|
| 1784 |
/** |
| 1785 |
* xcan_runtime_resume - Runtime resume from suspend |
| 1786 |
* @dev: Address of the device structure |
| 1787 |
* |
| 1788 |
* Resume operation after suspend. |
| 1789 |
* Return: 0 on success and failure value on error |
| 1790 |
*/ |
| 1791 |
static int __maybe_unused xcan_runtime_resume(struct device *dev) |
| 1792 |
{ |
| 1793 |
struct net_device *ndev = dev_get_drvdata(dev); |
| 1794 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 1795 |
int ret; |
| 1796 |
|
| 1797 |
ret = clk_prepare_enable(priv->bus_clk); |
| 1798 |
if (ret) { |
| 1799 |
dev_err(dev, "Cannot enable clock.\n"); |
| 1800 |
return ret; |
| 1801 |
} |
| 1802 |
ret = clk_prepare_enable(priv->can_clk); |
| 1803 |
if (ret) { |
| 1804 |
dev_err(dev, "Cannot enable clock.\n"); |
| 1805 |
clk_disable_unprepare(priv->bus_clk); |
| 1806 |
return ret; |
| 1807 |
} |
| 1808 |
|
| 1809 |
return 0; |
| 1810 |
} |
| 1811 |
|
| 1812 |
static const struct dev_pm_ops xcan_dev_pm_ops = { |
| 1813 |
SET_SYSTEM_SLEEP_PM_OPS(xcan_suspend, xcan_resume) |
| 1814 |
SET_RUNTIME_PM_OPS(xcan_runtime_suspend, xcan_runtime_resume, NULL) |
| 1815 |
}; |
| 1816 |
|
| 1817 |
static const struct xcan_devtype_data xcan_zynq_data = { |
| 1818 |
.cantype = XZYNQ_CANPS, |
| 1819 |
.flags = XCAN_FLAG_TXFEMP, |
| 1820 |
.bittiming_const = &xcan_bittiming_const, |
| 1821 |
.btr_ts2_shift = XCAN_BTR_TS2_SHIFT, |
| 1822 |
.btr_sjw_shift = XCAN_BTR_SJW_SHIFT, |
| 1823 |
.bus_clk_name = "pclk", |
| 1824 |
}; |
| 1825 |
|
| 1826 |
static const struct xcan_devtype_data xcan_axi_data = { |
| 1827 |
.cantype = XAXI_CAN, |
| 1828 |
.bittiming_const = &xcan_bittiming_const, |
| 1829 |
.btr_ts2_shift = XCAN_BTR_TS2_SHIFT, |
| 1830 |
.btr_sjw_shift = XCAN_BTR_SJW_SHIFT, |
| 1831 |
.bus_clk_name = "s_axi_aclk", |
| 1832 |
}; |
| 1833 |
|
| 1834 |
static const struct xcan_devtype_data xcan_canfd_data = { |
| 1835 |
.cantype = XAXI_CANFD, |
| 1836 |
.flags = XCAN_FLAG_EXT_FILTERS | |
| 1837 |
XCAN_FLAG_RXMNF | |
| 1838 |
XCAN_FLAG_TX_MAILBOXES | |
| 1839 |
XCAN_FLAG_RX_FIFO_MULTI, |
| 1840 |
.bittiming_const = &xcan_bittiming_const_canfd, |
| 1841 |
.btr_ts2_shift = XCAN_BTR_TS2_SHIFT_CANFD, |
| 1842 |
.btr_sjw_shift = XCAN_BTR_SJW_SHIFT_CANFD, |
| 1843 |
.bus_clk_name = "s_axi_aclk", |
| 1844 |
}; |
| 1845 |
|
| 1846 |
static const struct xcan_devtype_data xcan_canfd2_data = { |
| 1847 |
.cantype = XAXI_CANFD_2_0, |
| 1848 |
.flags = XCAN_FLAG_EXT_FILTERS | |
| 1849 |
XCAN_FLAG_RXMNF | |
| 1850 |
XCAN_FLAG_TX_MAILBOXES | |
| 1851 |
XCAN_FLAG_CANFD_2 | |
| 1852 |
XCAN_FLAG_RX_FIFO_MULTI, |
| 1853 |
.bittiming_const = &xcan_bittiming_const_canfd2, |
| 1854 |
.btr_ts2_shift = XCAN_BTR_TS2_SHIFT_CANFD, |
| 1855 |
.btr_sjw_shift = XCAN_BTR_SJW_SHIFT_CANFD, |
| 1856 |
.bus_clk_name = "s_axi_aclk", |
| 1857 |
}; |
| 1858 |
|
| 1859 |
/* Match table for OF platform binding */ |
| 1860 |
static const struct of_device_id xcan_of_match[] = { |
| 1861 |
{ .compatible = "xlnx,zynq-can-1.0", .data = &xcan_zynq_data }, |
| 1862 |
{ .compatible = "xlnx,axi-can-1.00.a", .data = &xcan_axi_data }, |
| 1863 |
{ .compatible = "xlnx,canfd-1.0", .data = &xcan_canfd_data }, |
| 1864 |
{ .compatible = "xlnx,canfd-2.0", .data = &xcan_canfd2_data }, |
| 1865 |
{ /* end of list */ }, |
| 1866 |
}; |
| 1867 |
MODULE_DEVICE_TABLE(of, xcan_of_match); |
| 1868 |
|
| 1869 |
/** |
| 1870 |
* xcan_probe - Platform registration call |
| 1871 |
* @pdev: Handle to the platform device structure |
| 1872 |
* |
| 1873 |
* This function does all the memory allocation and registration for the CAN |
| 1874 |
* device. |
| 1875 |
* |
| 1876 |
* Return: 0 on success and failure value on error |
| 1877 |
*/ |
| 1878 |
static int xcan_probe(struct platform_device *pdev) |
| 1879 |
{ |
| 1880 |
struct net_device *ndev; |
| 1881 |
struct xcan_priv *priv; |
| 1882 |
struct phy *transceiver; |
| 1883 |
const struct xcan_devtype_data *devtype; |
| 1884 |
void __iomem *addr; |
| 1885 |
int ret; |
| 1886 |
int rx_max, tx_max; |
| 1887 |
u32 hw_tx_max = 0, hw_rx_max = 0; |
| 1888 |
const char *hw_tx_max_property; |
| 1889 |
|
| 1890 |
/* Get the virtual base address for the device */ |
| 1891 |
addr = devm_platform_ioremap_resource(pdev, 0); |
| 1892 |
if (IS_ERR(addr)) { |
| 1893 |
ret = PTR_ERR(addr); |
| 1894 |
goto err; |
| 1895 |
} |
| 1896 |
|
| 1897 |
devtype = device_get_match_data(&pdev->dev); |
| 1898 |
|
| 1899 |
hw_tx_max_property = devtype->flags & XCAN_FLAG_TX_MAILBOXES ? |
| 1900 |
"tx-mailbox-count" : "tx-fifo-depth"; |
| 1901 |
|
| 1902 |
ret = of_property_read_u32(pdev->dev.of_node, hw_tx_max_property, |
| 1903 |
&hw_tx_max); |
| 1904 |
if (ret < 0) { |
| 1905 |
dev_err(&pdev->dev, "missing %s property\n", |
| 1906 |
hw_tx_max_property); |
| 1907 |
goto err; |
| 1908 |
} |
| 1909 |
|
| 1910 |
ret = of_property_read_u32(pdev->dev.of_node, "rx-fifo-depth", |
| 1911 |
&hw_rx_max); |
| 1912 |
if (ret < 0) { |
| 1913 |
dev_err(&pdev->dev, |
| 1914 |
"missing rx-fifo-depth property (mailbox mode is not supported)\n"); |
| 1915 |
goto err; |
| 1916 |
} |
| 1917 |
|
| 1918 |
/* With TX FIFO: |
| 1919 |
* |
| 1920 |
* There is no way to directly figure out how many frames have been |
| 1921 |
* sent when the TXOK interrupt is processed. If TXFEMP |
| 1922 |
* is supported, we can have 2 frames in the FIFO and use TXFEMP |
| 1923 |
* to determine if 1 or 2 frames have been sent. |
| 1924 |
* Theoretically we should be able to use TXFWMEMP to determine up |
| 1925 |
* to 3 frames, but it seems that after putting a second frame in the |
| 1926 |
* FIFO, with watermark at 2 frames, it can happen that TXFWMEMP (less |
| 1927 |
* than 2 frames in FIFO) is set anyway with no TXOK (a frame was |
| 1928 |
* sent), which is not a sensible state - possibly TXFWMEMP is not |
| 1929 |
* completely synchronized with the rest of the bits? |
| 1930 |
* |
| 1931 |
* With TX mailboxes: |
| 1932 |
* |
| 1933 |
* HW sends frames in CAN ID priority order. To preserve FIFO ordering |
| 1934 |
* we submit frames one at a time. |
| 1935 |
*/ |
| 1936 |
if (!(devtype->flags & XCAN_FLAG_TX_MAILBOXES) && |
| 1937 |
(devtype->flags & XCAN_FLAG_TXFEMP)) |
| 1938 |
tx_max = min(hw_tx_max, 2U); |
| 1939 |
else |
| 1940 |
tx_max = 1; |
| 1941 |
|
| 1942 |
rx_max = hw_rx_max; |
| 1943 |
|
| 1944 |
/* Create a CAN device instance */ |
| 1945 |
ndev = alloc_candev(sizeof(struct xcan_priv), tx_max); |
| 1946 |
if (!ndev) |
| 1947 |
return -ENOMEM; |
| 1948 |
|
| 1949 |
priv = netdev_priv(ndev); |
| 1950 |
priv->ecc_enable = of_property_read_bool(pdev->dev.of_node, "xlnx,has-ecc"); |
| 1951 |
priv->dev = &pdev->dev; |
| 1952 |
priv->can.bittiming_const = devtype->bittiming_const; |
| 1953 |
priv->can.do_set_mode = xcan_do_set_mode; |
| 1954 |
priv->can.do_get_berr_counter = xcan_get_berr_counter; |
| 1955 |
priv->can.ctrlmode_supported = CAN_CTRLMODE_LOOPBACK | |
| 1956 |
CAN_CTRLMODE_BERR_REPORTING; |
| 1957 |
priv->rstc = devm_reset_control_get_optional_exclusive(&pdev->dev, NULL); |
| 1958 |
if (IS_ERR(priv->rstc)) { |
| 1959 |
dev_err(&pdev->dev, "Cannot get CAN reset.\n"); |
| 1960 |
ret = PTR_ERR(priv->rstc); |
| 1961 |
goto err_free; |
| 1962 |
} |
| 1963 |
|
| 1964 |
ret = reset_control_reset(priv->rstc); |
| 1965 |
if (ret) |
| 1966 |
goto err_free; |
| 1967 |
|
| 1968 |
if (devtype->cantype == XAXI_CANFD) { |
| 1969 |
priv->can.fd.data_bittiming_const = |
| 1970 |
&xcan_data_bittiming_const_canfd; |
| 1971 |
priv->can.fd.tdc_const = &xcan_tdc_const_canfd; |
| 1972 |
} |
| 1973 |
|
| 1974 |
if (devtype->cantype == XAXI_CANFD_2_0) { |
| 1975 |
priv->can.fd.data_bittiming_const = |
| 1976 |
&xcan_data_bittiming_const_canfd2; |
| 1977 |
priv->can.fd.tdc_const = &xcan_tdc_const_canfd2; |
| 1978 |
} |
| 1979 |
|
| 1980 |
if (devtype->cantype == XAXI_CANFD || |
| 1981 |
devtype->cantype == XAXI_CANFD_2_0) { |
| 1982 |
priv->can.ctrlmode_supported |= CAN_CTRLMODE_FD | |
| 1983 |
CAN_CTRLMODE_TDC_AUTO; |
| 1984 |
priv->can.fd.do_get_auto_tdcv = xcan_get_auto_tdcv; |
| 1985 |
} |
| 1986 |
|
| 1987 |
priv->reg_base = addr; |
| 1988 |
priv->tx_max = tx_max; |
| 1989 |
priv->devtype = *devtype; |
| 1990 |
spin_lock_init(&priv->tx_lock); |
| 1991 |
|
| 1992 |
/* Get IRQ for the device */ |
| 1993 |
ret = platform_get_irq(pdev, 0); |
| 1994 |
if (ret < 0) |
| 1995 |
goto err_reset; |
| 1996 |
|
| 1997 |
ndev->irq = ret; |
| 1998 |
|
| 1999 |
ndev->flags |= IFF_ECHO; /* We support local echo */ |
| 2000 |
|
| 2001 |
platform_set_drvdata(pdev, ndev); |
| 2002 |
SET_NETDEV_DEV(ndev, &pdev->dev); |
| 2003 |
ndev->netdev_ops = &xcan_netdev_ops; |
| 2004 |
ndev->ethtool_ops = &xcan_ethtool_ops; |
| 2005 |
|
| 2006 |
/* Getting the CAN can_clk info */ |
| 2007 |
priv->can_clk = devm_clk_get(&pdev->dev, "can_clk"); |
| 2008 |
if (IS_ERR(priv->can_clk)) { |
| 2009 |
ret = dev_err_probe(&pdev->dev, PTR_ERR(priv->can_clk), |
| 2010 |
"device clock not found\n"); |
| 2011 |
goto err_reset; |
| 2012 |
} |
| 2013 |
|
| 2014 |
priv->bus_clk = devm_clk_get(&pdev->dev, devtype->bus_clk_name); |
| 2015 |
if (IS_ERR(priv->bus_clk)) { |
| 2016 |
ret = dev_err_probe(&pdev->dev, PTR_ERR(priv->bus_clk), |
| 2017 |
"bus clock not found\n"); |
| 2018 |
goto err_reset; |
| 2019 |
} |
| 2020 |
|
| 2021 |
transceiver = devm_phy_optional_get(&pdev->dev, NULL); |
| 2022 |
if (IS_ERR(transceiver)) { |
| 2023 |
ret = PTR_ERR(transceiver); |
| 2024 |
dev_err_probe(&pdev->dev, ret, "failed to get phy\n"); |
| 2025 |
goto err_reset; |
| 2026 |
} |
| 2027 |
priv->transceiver = transceiver; |
| 2028 |
|
| 2029 |
priv->write_reg = xcan_write_reg_le; |
| 2030 |
priv->read_reg = xcan_read_reg_le; |
| 2031 |
|
| 2032 |
pm_runtime_enable(&pdev->dev); |
| 2033 |
ret = pm_runtime_get_sync(&pdev->dev); |
| 2034 |
if (ret < 0) { |
| 2035 |
netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n", |
| 2036 |
__func__, ret); |
| 2037 |
goto err_disableclks; |
| 2038 |
} |
| 2039 |
|
| 2040 |
if (priv->read_reg(priv, XCAN_SR_OFFSET) != XCAN_SR_CONFIG_MASK) { |
| 2041 |
priv->write_reg = xcan_write_reg_be; |
| 2042 |
priv->read_reg = xcan_read_reg_be; |
| 2043 |
} |
| 2044 |
|
| 2045 |
priv->can.clock.freq = clk_get_rate(priv->can_clk); |
| 2046 |
|
| 2047 |
netif_napi_add_weight(ndev, &priv->napi, xcan_rx_poll, rx_max); |
| 2048 |
|
| 2049 |
ret = register_candev(ndev); |
| 2050 |
if (ret) { |
| 2051 |
dev_err(&pdev->dev, "fail to register failed (err=%d)\n", ret); |
| 2052 |
goto err_disableclks; |
| 2053 |
} |
| 2054 |
|
| 2055 |
of_can_transceiver(ndev); |
| 2056 |
pm_runtime_put(&pdev->dev); |
| 2057 |
|
| 2058 |
if (priv->devtype.flags & XCAN_FLAG_CANFD_2) { |
| 2059 |
priv->write_reg(priv, XCAN_AFR_2_ID_OFFSET, 0x00000000); |
| 2060 |
priv->write_reg(priv, XCAN_AFR_2_MASK_OFFSET, 0x00000000); |
| 2061 |
} |
| 2062 |
|
| 2063 |
netdev_dbg(ndev, "reg_base=0x%p irq=%d clock=%d, tx buffers: actual %d, using %d\n", |
| 2064 |
priv->reg_base, ndev->irq, priv->can.clock.freq, |
| 2065 |
hw_tx_max, priv->tx_max); |
| 2066 |
|
| 2067 |
if (priv->ecc_enable) { |
| 2068 |
/* Reset FIFO ECC counters */ |
| 2069 |
priv->write_reg(priv, XCAN_ECC_CFG_OFFSET, XCAN_ECC_CFG_REECRX_MASK | |
| 2070 |
XCAN_ECC_CFG_REECTXOL_MASK | XCAN_ECC_CFG_REECTXTL_MASK); |
| 2071 |
} |
| 2072 |
return 0; |
| 2073 |
|
| 2074 |
err_disableclks: |
| 2075 |
pm_runtime_put(priv->dev); |
| 2076 |
pm_runtime_disable(&pdev->dev); |
| 2077 |
err_reset: |
| 2078 |
reset_control_assert(priv->rstc); |
| 2079 |
err_free: |
| 2080 |
free_candev(ndev); |
| 2081 |
err: |
| 2082 |
return ret; |
| 2083 |
} |
| 2084 |
|
| 2085 |
/** |
| 2086 |
* xcan_remove - Unregister the device after releasing the resources |
| 2087 |
* @pdev: Handle to the platform device structure |
| 2088 |
* |
| 2089 |
* This function frees all the resources allocated to the device. |
| 2090 |
* Return: 0 always |
| 2091 |
*/ |
| 2092 |
static void xcan_remove(struct platform_device *pdev) |
| 2093 |
{ |
| 2094 |
struct net_device *ndev = platform_get_drvdata(pdev); |
| 2095 |
struct xcan_priv *priv = netdev_priv(ndev); |
| 2096 |
|
| 2097 |
unregister_candev(ndev); |
| 2098 |
pm_runtime_disable(&pdev->dev); |
| 2099 |
reset_control_assert(priv->rstc); |
| 2100 |
free_candev(ndev); |
| 2101 |
} |
| 2102 |
|
| 2103 |
static struct platform_driver xcan_driver = { |
| 2104 |
.probe = xcan_probe, |
| 2105 |
.remove = xcan_remove, |
| 2106 |
.driver = { |
| 2107 |
.name = DRIVER_NAME, |
| 2108 |
.pm = &xcan_dev_pm_ops, |
| 2109 |
.of_match_table = xcan_of_match, |
| 2110 |
}, |
| 2111 |
}; |
| 2112 |
|
| 2113 |
module_platform_driver(xcan_driver); |
| 2114 |
|
| 2115 |
MODULE_LICENSE("GPL"); |
| 2116 |
MODULE_AUTHOR("Xilinx Inc"); |
| 2117 |
MODULE_DESCRIPTION("Xilinx CAN interface"); |