| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* Janz MODULbus VMOD-ICAN3 CAN Interface Driver |
| 4 |
* |
| 5 |
* Copyright (c) 2010 Ira W. Snyder <[email protected]> |
| 6 |
*/ |
| 7 |
|
| 8 |
#include <linux/kernel.h> |
| 9 |
#include <linux/module.h> |
| 10 |
#include <linux/interrupt.h> |
| 11 |
#include <linux/delay.h> |
| 12 |
#include <linux/ethtool.h> |
| 13 |
#include <linux/platform_device.h> |
| 14 |
|
| 15 |
#include <linux/netdevice.h> |
| 16 |
#include <linux/can.h> |
| 17 |
#include <linux/can/dev.h> |
| 18 |
#include <linux/can/skb.h> |
| 19 |
#include <linux/can/error.h> |
| 20 |
|
| 21 |
#include <linux/mfd/janz.h> |
| 22 |
#include <asm/io.h> |
| 23 |
|
| 24 |
/* the DPM has 64k of memory, organized into 256x 256 byte pages */ |
| 25 |
#define DPM_NUM_PAGES 256 |
| 26 |
#define DPM_PAGE_SIZE 256 |
| 27 |
#define DPM_PAGE_ADDR(p) ((p) * DPM_PAGE_SIZE) |
| 28 |
|
| 29 |
/* JANZ ICAN3 "old-style" host interface queue page numbers */ |
| 30 |
#define QUEUE_OLD_CONTROL 0 |
| 31 |
#define QUEUE_OLD_RB0 1 |
| 32 |
#define QUEUE_OLD_RB1 2 |
| 33 |
#define QUEUE_OLD_WB0 3 |
| 34 |
#define QUEUE_OLD_WB1 4 |
| 35 |
|
| 36 |
/* Janz ICAN3 "old-style" host interface control registers */ |
| 37 |
#define MSYNC_PEER 0x00 /* ICAN only */ |
| 38 |
#define MSYNC_LOCL 0x01 /* host only */ |
| 39 |
#define TARGET_RUNNING 0x02 |
| 40 |
#define FIRMWARE_STAMP 0x60 /* big endian firmware stamp */ |
| 41 |
|
| 42 |
#define MSYNC_RB0 0x01 |
| 43 |
#define MSYNC_RB1 0x02 |
| 44 |
#define MSYNC_RBLW 0x04 |
| 45 |
#define MSYNC_RB_MASK (MSYNC_RB0 | MSYNC_RB1) |
| 46 |
|
| 47 |
#define MSYNC_WB0 0x10 |
| 48 |
#define MSYNC_WB1 0x20 |
| 49 |
#define MSYNC_WBLW 0x40 |
| 50 |
#define MSYNC_WB_MASK (MSYNC_WB0 | MSYNC_WB1) |
| 51 |
|
| 52 |
/* Janz ICAN3 "new-style" host interface queue page numbers */ |
| 53 |
#define QUEUE_TOHOST 5 |
| 54 |
#define QUEUE_FROMHOST_MID 6 |
| 55 |
#define QUEUE_FROMHOST_HIGH 7 |
| 56 |
#define QUEUE_FROMHOST_LOW 8 |
| 57 |
|
| 58 |
/* The first free page in the DPM is #9 */ |
| 59 |
#define DPM_FREE_START 9 |
| 60 |
|
| 61 |
/* Janz ICAN3 "new-style" and "fast" host interface descriptor flags */ |
| 62 |
#define DESC_VALID 0x80 |
| 63 |
#define DESC_WRAP 0x40 |
| 64 |
#define DESC_INTERRUPT 0x20 |
| 65 |
#define DESC_IVALID 0x10 |
| 66 |
#define DESC_LEN(len) (len) |
| 67 |
|
| 68 |
/* Janz ICAN3 Firmware Messages */ |
| 69 |
#define MSG_CONNECTI 0x02 |
| 70 |
#define MSG_DISCONNECT 0x03 |
| 71 |
#define MSG_IDVERS 0x04 |
| 72 |
#define MSG_MSGLOST 0x05 |
| 73 |
#define MSG_NEWHOSTIF 0x08 |
| 74 |
#define MSG_INQUIRY 0x0a |
| 75 |
#define MSG_SETAFILMASK 0x10 |
| 76 |
#define MSG_INITFDPMQUEUE 0x11 |
| 77 |
#define MSG_HWCONF 0x12 |
| 78 |
#define MSG_FMSGLOST 0x15 |
| 79 |
#define MSG_CEVTIND 0x37 |
| 80 |
#define MSG_CBTRREQ 0x41 |
| 81 |
#define MSG_COFFREQ 0x42 |
| 82 |
#define MSG_CONREQ 0x43 |
| 83 |
#define MSG_CCONFREQ 0x47 |
| 84 |
#define MSG_NMTS 0xb0 |
| 85 |
#define MSG_LMTS 0xb4 |
| 86 |
|
| 87 |
/* |
| 88 |
* Janz ICAN3 CAN Inquiry Message Types |
| 89 |
* |
| 90 |
* NOTE: there appears to be a firmware bug here. You must send |
| 91 |
* NOTE: INQUIRY_STATUS and expect to receive an INQUIRY_EXTENDED |
| 92 |
* NOTE: response. The controller never responds to a message with |
| 93 |
* NOTE: the INQUIRY_EXTENDED subspec :( |
| 94 |
*/ |
| 95 |
#define INQUIRY_STATUS 0x00 |
| 96 |
#define INQUIRY_TERMINATION 0x01 |
| 97 |
#define INQUIRY_EXTENDED 0x04 |
| 98 |
|
| 99 |
/* Janz ICAN3 CAN Set Acceptance Filter Mask Message Types */ |
| 100 |
#define SETAFILMASK_REJECT 0x00 |
| 101 |
#define SETAFILMASK_FASTIF 0x02 |
| 102 |
|
| 103 |
/* Janz ICAN3 CAN Hardware Configuration Message Types */ |
| 104 |
#define HWCONF_TERMINATE_ON 0x01 |
| 105 |
#define HWCONF_TERMINATE_OFF 0x00 |
| 106 |
|
| 107 |
/* Janz ICAN3 CAN Event Indication Message Types */ |
| 108 |
#define CEVTIND_EI 0x01 |
| 109 |
#define CEVTIND_DOI 0x02 |
| 110 |
#define CEVTIND_LOST 0x04 |
| 111 |
#define CEVTIND_FULL 0x08 |
| 112 |
#define CEVTIND_BEI 0x10 |
| 113 |
|
| 114 |
#define CEVTIND_CHIP_SJA1000 0x02 |
| 115 |
|
| 116 |
#define ICAN3_BUSERR_QUOTA_MAX 255 |
| 117 |
|
| 118 |
/* Janz ICAN3 CAN Frame Conversion */ |
| 119 |
#define ICAN3_SNGL 0x02 |
| 120 |
#define ICAN3_ECHO 0x10 |
| 121 |
#define ICAN3_EFF_RTR 0x40 |
| 122 |
#define ICAN3_SFF_RTR 0x10 |
| 123 |
#define ICAN3_EFF 0x80 |
| 124 |
|
| 125 |
#define ICAN3_CAN_TYPE_MASK 0x0f |
| 126 |
#define ICAN3_CAN_TYPE_SFF 0x00 |
| 127 |
#define ICAN3_CAN_TYPE_EFF 0x01 |
| 128 |
|
| 129 |
#define ICAN3_CAN_DLC_MASK 0x0f |
| 130 |
|
| 131 |
/* Janz ICAN3 NMTS subtypes */ |
| 132 |
#define NMTS_CREATE_NODE_REQ 0x0 |
| 133 |
#define NMTS_SLAVE_STATE_IND 0x8 |
| 134 |
#define NMTS_SLAVE_EVENT_IND 0x9 |
| 135 |
|
| 136 |
/* Janz ICAN3 LMTS subtypes */ |
| 137 |
#define LMTS_BUSON_REQ 0x0 |
| 138 |
#define LMTS_BUSOFF_REQ 0x1 |
| 139 |
#define LMTS_CAN_CONF_REQ 0x2 |
| 140 |
|
| 141 |
/* Janz ICAN3 NMTS Event indications */ |
| 142 |
#define NE_LOCAL_OCCURRED 0x3 |
| 143 |
#define NE_LOCAL_RESOLVED 0x2 |
| 144 |
#define NE_REMOTE_OCCURRED 0xc |
| 145 |
#define NE_REMOTE_RESOLVED 0x8 |
| 146 |
|
| 147 |
/* |
| 148 |
* SJA1000 Status and Error Register Definitions |
| 149 |
* |
| 150 |
* Copied from drivers/net/can/sja1000/sja1000.h |
| 151 |
*/ |
| 152 |
|
| 153 |
/* status register content */ |
| 154 |
#define SR_BS 0x80 |
| 155 |
#define SR_ES 0x40 |
| 156 |
#define SR_TS 0x20 |
| 157 |
#define SR_RS 0x10 |
| 158 |
#define SR_TCS 0x08 |
| 159 |
#define SR_TBS 0x04 |
| 160 |
#define SR_DOS 0x02 |
| 161 |
#define SR_RBS 0x01 |
| 162 |
|
| 163 |
#define SR_CRIT (SR_BS|SR_ES) |
| 164 |
|
| 165 |
/* ECC register */ |
| 166 |
#define ECC_SEG 0x1F |
| 167 |
#define ECC_DIR 0x20 |
| 168 |
#define ECC_ERR 6 |
| 169 |
#define ECC_BIT 0x00 |
| 170 |
#define ECC_FORM 0x40 |
| 171 |
#define ECC_STUFF 0x80 |
| 172 |
#define ECC_MASK 0xc0 |
| 173 |
|
| 174 |
/* Number of buffers for use in the "new-style" host interface */ |
| 175 |
#define ICAN3_NEW_BUFFERS 16 |
| 176 |
|
| 177 |
/* Number of buffers for use in the "fast" host interface */ |
| 178 |
#define ICAN3_TX_BUFFERS 512 |
| 179 |
#define ICAN3_RX_BUFFERS 1024 |
| 180 |
|
| 181 |
/* SJA1000 Clock Input */ |
| 182 |
#define ICAN3_CAN_CLOCK 8000000 |
| 183 |
|
| 184 |
/* Janz ICAN3 firmware types */ |
| 185 |
enum ican3_fwtype { |
| 186 |
ICAN3_FWTYPE_ICANOS, |
| 187 |
ICAN3_FWTYPE_CAL_CANOPEN, |
| 188 |
}; |
| 189 |
|
| 190 |
/* Driver Name */ |
| 191 |
#define DRV_NAME "janz-ican3" |
| 192 |
|
| 193 |
/* DPM Control Registers -- starts at offset 0x100 in the MODULbus registers */ |
| 194 |
struct ican3_dpm_control { |
| 195 |
/* window address register */ |
| 196 |
u8 window_address; |
| 197 |
u8 unused1; |
| 198 |
|
| 199 |
/* |
| 200 |
* Read access: clear interrupt from microcontroller |
| 201 |
* Write access: send interrupt to microcontroller |
| 202 |
*/ |
| 203 |
u8 interrupt; |
| 204 |
u8 unused2; |
| 205 |
|
| 206 |
/* write-only: reset all hardware on the module */ |
| 207 |
u8 hwreset; |
| 208 |
u8 unused3; |
| 209 |
|
| 210 |
/* write-only: generate an interrupt to the TPU */ |
| 211 |
u8 tpuinterrupt; |
| 212 |
}; |
| 213 |
|
| 214 |
struct ican3_dev { |
| 215 |
|
| 216 |
/* must be the first member */ |
| 217 |
struct can_priv can; |
| 218 |
|
| 219 |
/* CAN network device */ |
| 220 |
struct net_device *ndev; |
| 221 |
struct napi_struct napi; |
| 222 |
|
| 223 |
/* module number */ |
| 224 |
unsigned int num; |
| 225 |
|
| 226 |
/* base address of registers and IRQ */ |
| 227 |
struct janz_cmodio_onboard_regs __iomem *ctrl; |
| 228 |
struct ican3_dpm_control __iomem *dpmctrl; |
| 229 |
void __iomem *dpm; |
| 230 |
int irq; |
| 231 |
|
| 232 |
/* CAN bus termination status */ |
| 233 |
struct completion termination_comp; |
| 234 |
bool termination_enabled; |
| 235 |
|
| 236 |
/* CAN bus error status registers */ |
| 237 |
struct completion buserror_comp; |
| 238 |
struct can_berr_counter bec; |
| 239 |
|
| 240 |
/* firmware type */ |
| 241 |
enum ican3_fwtype fwtype; |
| 242 |
char fwinfo[32]; |
| 243 |
|
| 244 |
/* old and new style host interface */ |
| 245 |
unsigned int iftype; |
| 246 |
|
| 247 |
/* queue for echo packets */ |
| 248 |
struct sk_buff_head echoq; |
| 249 |
|
| 250 |
/* |
| 251 |
* Any function which changes the current DPM page must hold this |
| 252 |
* lock while it is performing data accesses. This ensures that the |
| 253 |
* function will not be preempted and end up reading data from a |
| 254 |
* different DPM page than it expects. |
| 255 |
*/ |
| 256 |
spinlock_t lock; |
| 257 |
|
| 258 |
/* new host interface */ |
| 259 |
unsigned int rx_int; |
| 260 |
unsigned int rx_num; |
| 261 |
unsigned int tx_num; |
| 262 |
|
| 263 |
/* fast host interface */ |
| 264 |
unsigned int fastrx_start; |
| 265 |
unsigned int fastrx_num; |
| 266 |
unsigned int fasttx_start; |
| 267 |
unsigned int fasttx_num; |
| 268 |
|
| 269 |
/* first free DPM page */ |
| 270 |
unsigned int free_page; |
| 271 |
}; |
| 272 |
|
| 273 |
struct ican3_msg { |
| 274 |
u8 control; |
| 275 |
u8 spec; |
| 276 |
__le16 len; |
| 277 |
u8 data[252]; |
| 278 |
}; |
| 279 |
|
| 280 |
struct ican3_new_desc { |
| 281 |
u8 control; |
| 282 |
u8 pointer; |
| 283 |
}; |
| 284 |
|
| 285 |
struct ican3_fast_desc { |
| 286 |
u8 control; |
| 287 |
u8 command; |
| 288 |
u8 data[14]; |
| 289 |
}; |
| 290 |
|
| 291 |
/* write to the window basic address register */ |
| 292 |
static inline void ican3_set_page(struct ican3_dev *mod, unsigned int page) |
| 293 |
{ |
| 294 |
BUG_ON(page >= DPM_NUM_PAGES); |
| 295 |
iowrite8(page, &mod->dpmctrl->window_address); |
| 296 |
} |
| 297 |
|
| 298 |
/* |
| 299 |
* ICAN3 "old-style" host interface |
| 300 |
*/ |
| 301 |
|
| 302 |
/* |
| 303 |
* Receive a message from the ICAN3 "old-style" firmware interface |
| 304 |
* |
| 305 |
* LOCKING: must hold mod->lock |
| 306 |
* |
| 307 |
* returns 0 on success, -ENOMEM when no message exists |
| 308 |
*/ |
| 309 |
static int ican3_old_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) |
| 310 |
{ |
| 311 |
unsigned int mbox, mbox_page; |
| 312 |
u8 locl, peer, xord; |
| 313 |
|
| 314 |
/* get the MSYNC registers */ |
| 315 |
ican3_set_page(mod, QUEUE_OLD_CONTROL); |
| 316 |
peer = ioread8(mod->dpm + MSYNC_PEER); |
| 317 |
locl = ioread8(mod->dpm + MSYNC_LOCL); |
| 318 |
xord = locl ^ peer; |
| 319 |
|
| 320 |
if ((xord & MSYNC_RB_MASK) == 0x00) { |
| 321 |
netdev_dbg(mod->ndev, "no mbox for reading\n"); |
| 322 |
return -ENOMEM; |
| 323 |
} |
| 324 |
|
| 325 |
/* find the first free mbox to read */ |
| 326 |
if ((xord & MSYNC_RB_MASK) == MSYNC_RB_MASK) |
| 327 |
mbox = (xord & MSYNC_RBLW) ? MSYNC_RB0 : MSYNC_RB1; |
| 328 |
else |
| 329 |
mbox = (xord & MSYNC_RB0) ? MSYNC_RB0 : MSYNC_RB1; |
| 330 |
|
| 331 |
/* copy the message */ |
| 332 |
mbox_page = (mbox == MSYNC_RB0) ? QUEUE_OLD_RB0 : QUEUE_OLD_RB1; |
| 333 |
ican3_set_page(mod, mbox_page); |
| 334 |
memcpy_fromio(msg, mod->dpm, sizeof(*msg)); |
| 335 |
|
| 336 |
/* |
| 337 |
* notify the firmware that the read buffer is available |
| 338 |
* for it to fill again |
| 339 |
*/ |
| 340 |
locl ^= mbox; |
| 341 |
|
| 342 |
ican3_set_page(mod, QUEUE_OLD_CONTROL); |
| 343 |
iowrite8(locl, mod->dpm + MSYNC_LOCL); |
| 344 |
return 0; |
| 345 |
} |
| 346 |
|
| 347 |
/* |
| 348 |
* Send a message through the "old-style" firmware interface |
| 349 |
* |
| 350 |
* LOCKING: must hold mod->lock |
| 351 |
* |
| 352 |
* returns 0 on success, -ENOMEM when no free space exists |
| 353 |
*/ |
| 354 |
static int ican3_old_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) |
| 355 |
{ |
| 356 |
unsigned int mbox, mbox_page; |
| 357 |
u8 locl, peer, xord; |
| 358 |
|
| 359 |
/* get the MSYNC registers */ |
| 360 |
ican3_set_page(mod, QUEUE_OLD_CONTROL); |
| 361 |
peer = ioread8(mod->dpm + MSYNC_PEER); |
| 362 |
locl = ioread8(mod->dpm + MSYNC_LOCL); |
| 363 |
xord = locl ^ peer; |
| 364 |
|
| 365 |
if ((xord & MSYNC_WB_MASK) == MSYNC_WB_MASK) { |
| 366 |
netdev_err(mod->ndev, "no mbox for writing\n"); |
| 367 |
return -ENOMEM; |
| 368 |
} |
| 369 |
|
| 370 |
/* calculate a free mbox to use */ |
| 371 |
mbox = (xord & MSYNC_WB0) ? MSYNC_WB1 : MSYNC_WB0; |
| 372 |
|
| 373 |
/* copy the message to the DPM */ |
| 374 |
mbox_page = (mbox == MSYNC_WB0) ? QUEUE_OLD_WB0 : QUEUE_OLD_WB1; |
| 375 |
ican3_set_page(mod, mbox_page); |
| 376 |
memcpy_toio(mod->dpm, msg, sizeof(*msg)); |
| 377 |
|
| 378 |
locl ^= mbox; |
| 379 |
if (mbox == MSYNC_WB1) |
| 380 |
locl |= MSYNC_WBLW; |
| 381 |
|
| 382 |
ican3_set_page(mod, QUEUE_OLD_CONTROL); |
| 383 |
iowrite8(locl, mod->dpm + MSYNC_LOCL); |
| 384 |
return 0; |
| 385 |
} |
| 386 |
|
| 387 |
/* |
| 388 |
* ICAN3 "new-style" Host Interface Setup |
| 389 |
*/ |
| 390 |
|
| 391 |
static void ican3_init_new_host_interface(struct ican3_dev *mod) |
| 392 |
{ |
| 393 |
struct ican3_new_desc desc; |
| 394 |
unsigned long flags; |
| 395 |
void __iomem *dst; |
| 396 |
int i; |
| 397 |
|
| 398 |
spin_lock_irqsave(&mod->lock, flags); |
| 399 |
|
| 400 |
/* setup the internal datastructures for RX */ |
| 401 |
mod->rx_num = 0; |
| 402 |
mod->rx_int = 0; |
| 403 |
|
| 404 |
/* tohost queue descriptors are in page 5 */ |
| 405 |
ican3_set_page(mod, QUEUE_TOHOST); |
| 406 |
dst = mod->dpm; |
| 407 |
|
| 408 |
/* initialize the tohost (rx) queue descriptors: pages 9-24 */ |
| 409 |
for (i = 0; i < ICAN3_NEW_BUFFERS; i++) { |
| 410 |
desc.control = DESC_INTERRUPT | DESC_LEN(1); /* I L=1 */ |
| 411 |
desc.pointer = mod->free_page; |
| 412 |
|
| 413 |
/* set wrap flag on last buffer */ |
| 414 |
if (i == ICAN3_NEW_BUFFERS - 1) |
| 415 |
desc.control |= DESC_WRAP; |
| 416 |
|
| 417 |
memcpy_toio(dst, &desc, sizeof(desc)); |
| 418 |
dst += sizeof(desc); |
| 419 |
mod->free_page++; |
| 420 |
} |
| 421 |
|
| 422 |
/* fromhost (tx) mid queue descriptors are in page 6 */ |
| 423 |
ican3_set_page(mod, QUEUE_FROMHOST_MID); |
| 424 |
dst = mod->dpm; |
| 425 |
|
| 426 |
/* setup the internal datastructures for TX */ |
| 427 |
mod->tx_num = 0; |
| 428 |
|
| 429 |
/* initialize the fromhost mid queue descriptors: pages 25-40 */ |
| 430 |
for (i = 0; i < ICAN3_NEW_BUFFERS; i++) { |
| 431 |
desc.control = DESC_VALID | DESC_LEN(1); /* V L=1 */ |
| 432 |
desc.pointer = mod->free_page; |
| 433 |
|
| 434 |
/* set wrap flag on last buffer */ |
| 435 |
if (i == ICAN3_NEW_BUFFERS - 1) |
| 436 |
desc.control |= DESC_WRAP; |
| 437 |
|
| 438 |
memcpy_toio(dst, &desc, sizeof(desc)); |
| 439 |
dst += sizeof(desc); |
| 440 |
mod->free_page++; |
| 441 |
} |
| 442 |
|
| 443 |
/* fromhost hi queue descriptors are in page 7 */ |
| 444 |
ican3_set_page(mod, QUEUE_FROMHOST_HIGH); |
| 445 |
dst = mod->dpm; |
| 446 |
|
| 447 |
/* initialize only a single buffer in the fromhost hi queue (unused) */ |
| 448 |
desc.control = DESC_VALID | DESC_WRAP | DESC_LEN(1); /* VW L=1 */ |
| 449 |
desc.pointer = mod->free_page; |
| 450 |
memcpy_toio(dst, &desc, sizeof(desc)); |
| 451 |
mod->free_page++; |
| 452 |
|
| 453 |
/* fromhost low queue descriptors are in page 8 */ |
| 454 |
ican3_set_page(mod, QUEUE_FROMHOST_LOW); |
| 455 |
dst = mod->dpm; |
| 456 |
|
| 457 |
/* initialize only a single buffer in the fromhost low queue (unused) */ |
| 458 |
desc.control = DESC_VALID | DESC_WRAP | DESC_LEN(1); /* VW L=1 */ |
| 459 |
desc.pointer = mod->free_page; |
| 460 |
memcpy_toio(dst, &desc, sizeof(desc)); |
| 461 |
mod->free_page++; |
| 462 |
|
| 463 |
spin_unlock_irqrestore(&mod->lock, flags); |
| 464 |
} |
| 465 |
|
| 466 |
/* |
| 467 |
* ICAN3 Fast Host Interface Setup |
| 468 |
*/ |
| 469 |
|
| 470 |
static void ican3_init_fast_host_interface(struct ican3_dev *mod) |
| 471 |
{ |
| 472 |
struct ican3_fast_desc desc; |
| 473 |
unsigned long flags; |
| 474 |
unsigned int addr; |
| 475 |
void __iomem *dst; |
| 476 |
int i; |
| 477 |
|
| 478 |
spin_lock_irqsave(&mod->lock, flags); |
| 479 |
|
| 480 |
/* save the start recv page */ |
| 481 |
mod->fastrx_start = mod->free_page; |
| 482 |
mod->fastrx_num = 0; |
| 483 |
|
| 484 |
/* build a single fast tohost queue descriptor */ |
| 485 |
memset(&desc, 0, sizeof(desc)); |
| 486 |
desc.control = 0x00; |
| 487 |
desc.command = 1; |
| 488 |
|
| 489 |
/* build the tohost queue descriptor ring in memory */ |
| 490 |
addr = 0; |
| 491 |
for (i = 0; i < ICAN3_RX_BUFFERS; i++) { |
| 492 |
|
| 493 |
/* set the wrap bit on the last buffer */ |
| 494 |
if (i == ICAN3_RX_BUFFERS - 1) |
| 495 |
desc.control |= DESC_WRAP; |
| 496 |
|
| 497 |
/* switch to the correct page */ |
| 498 |
ican3_set_page(mod, mod->free_page); |
| 499 |
|
| 500 |
/* copy the descriptor to the DPM */ |
| 501 |
dst = mod->dpm + addr; |
| 502 |
memcpy_toio(dst, &desc, sizeof(desc)); |
| 503 |
addr += sizeof(desc); |
| 504 |
|
| 505 |
/* move to the next page if necessary */ |
| 506 |
if (addr >= DPM_PAGE_SIZE) { |
| 507 |
addr = 0; |
| 508 |
mod->free_page++; |
| 509 |
} |
| 510 |
} |
| 511 |
|
| 512 |
/* make sure we page-align the next queue */ |
| 513 |
if (addr != 0) |
| 514 |
mod->free_page++; |
| 515 |
|
| 516 |
/* save the start xmit page */ |
| 517 |
mod->fasttx_start = mod->free_page; |
| 518 |
mod->fasttx_num = 0; |
| 519 |
|
| 520 |
/* build a single fast fromhost queue descriptor */ |
| 521 |
memset(&desc, 0, sizeof(desc)); |
| 522 |
desc.control = DESC_VALID; |
| 523 |
desc.command = 1; |
| 524 |
|
| 525 |
/* build the fromhost queue descriptor ring in memory */ |
| 526 |
addr = 0; |
| 527 |
for (i = 0; i < ICAN3_TX_BUFFERS; i++) { |
| 528 |
|
| 529 |
/* set the wrap bit on the last buffer */ |
| 530 |
if (i == ICAN3_TX_BUFFERS - 1) |
| 531 |
desc.control |= DESC_WRAP; |
| 532 |
|
| 533 |
/* switch to the correct page */ |
| 534 |
ican3_set_page(mod, mod->free_page); |
| 535 |
|
| 536 |
/* copy the descriptor to the DPM */ |
| 537 |
dst = mod->dpm + addr; |
| 538 |
memcpy_toio(dst, &desc, sizeof(desc)); |
| 539 |
addr += sizeof(desc); |
| 540 |
|
| 541 |
/* move to the next page if necessary */ |
| 542 |
if (addr >= DPM_PAGE_SIZE) { |
| 543 |
addr = 0; |
| 544 |
mod->free_page++; |
| 545 |
} |
| 546 |
} |
| 547 |
|
| 548 |
spin_unlock_irqrestore(&mod->lock, flags); |
| 549 |
} |
| 550 |
|
| 551 |
/* |
| 552 |
* ICAN3 "new-style" Host Interface Message Helpers |
| 553 |
*/ |
| 554 |
|
| 555 |
/* |
| 556 |
* LOCKING: must hold mod->lock |
| 557 |
*/ |
| 558 |
static int ican3_new_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) |
| 559 |
{ |
| 560 |
struct ican3_new_desc desc; |
| 561 |
void __iomem *desc_addr = mod->dpm + (mod->tx_num * sizeof(desc)); |
| 562 |
|
| 563 |
/* switch to the fromhost mid queue, and read the buffer descriptor */ |
| 564 |
ican3_set_page(mod, QUEUE_FROMHOST_MID); |
| 565 |
memcpy_fromio(&desc, desc_addr, sizeof(desc)); |
| 566 |
|
| 567 |
if (!(desc.control & DESC_VALID)) { |
| 568 |
netdev_dbg(mod->ndev, "%s: no free buffers\n", __func__); |
| 569 |
return -ENOMEM; |
| 570 |
} |
| 571 |
|
| 572 |
/* switch to the data page, copy the data */ |
| 573 |
ican3_set_page(mod, desc.pointer); |
| 574 |
memcpy_toio(mod->dpm, msg, sizeof(*msg)); |
| 575 |
|
| 576 |
/* switch back to the descriptor, set the valid bit, write it back */ |
| 577 |
ican3_set_page(mod, QUEUE_FROMHOST_MID); |
| 578 |
desc.control ^= DESC_VALID; |
| 579 |
memcpy_toio(desc_addr, &desc, sizeof(desc)); |
| 580 |
|
| 581 |
/* update the tx number */ |
| 582 |
mod->tx_num = (desc.control & DESC_WRAP) ? 0 : (mod->tx_num + 1); |
| 583 |
return 0; |
| 584 |
} |
| 585 |
|
| 586 |
/* |
| 587 |
* LOCKING: must hold mod->lock |
| 588 |
*/ |
| 589 |
static int ican3_new_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) |
| 590 |
{ |
| 591 |
struct ican3_new_desc desc; |
| 592 |
void __iomem *desc_addr = mod->dpm + (mod->rx_num * sizeof(desc)); |
| 593 |
|
| 594 |
/* switch to the tohost queue, and read the buffer descriptor */ |
| 595 |
ican3_set_page(mod, QUEUE_TOHOST); |
| 596 |
memcpy_fromio(&desc, desc_addr, sizeof(desc)); |
| 597 |
|
| 598 |
if (!(desc.control & DESC_VALID)) { |
| 599 |
netdev_dbg(mod->ndev, "%s: no buffers to recv\n", __func__); |
| 600 |
return -ENOMEM; |
| 601 |
} |
| 602 |
|
| 603 |
/* switch to the data page, copy the data */ |
| 604 |
ican3_set_page(mod, desc.pointer); |
| 605 |
memcpy_fromio(msg, mod->dpm, sizeof(*msg)); |
| 606 |
|
| 607 |
/* switch back to the descriptor, toggle the valid bit, write it back */ |
| 608 |
ican3_set_page(mod, QUEUE_TOHOST); |
| 609 |
desc.control ^= DESC_VALID; |
| 610 |
memcpy_toio(desc_addr, &desc, sizeof(desc)); |
| 611 |
|
| 612 |
/* update the rx number */ |
| 613 |
mod->rx_num = (desc.control & DESC_WRAP) ? 0 : (mod->rx_num + 1); |
| 614 |
return 0; |
| 615 |
} |
| 616 |
|
| 617 |
/* |
| 618 |
* Message Send / Recv Helpers |
| 619 |
*/ |
| 620 |
|
| 621 |
static int ican3_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) |
| 622 |
{ |
| 623 |
unsigned long flags; |
| 624 |
int ret; |
| 625 |
|
| 626 |
spin_lock_irqsave(&mod->lock, flags); |
| 627 |
|
| 628 |
if (mod->iftype == 0) |
| 629 |
ret = ican3_old_send_msg(mod, msg); |
| 630 |
else |
| 631 |
ret = ican3_new_send_msg(mod, msg); |
| 632 |
|
| 633 |
spin_unlock_irqrestore(&mod->lock, flags); |
| 634 |
return ret; |
| 635 |
} |
| 636 |
|
| 637 |
static int ican3_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) |
| 638 |
{ |
| 639 |
unsigned long flags; |
| 640 |
int ret; |
| 641 |
|
| 642 |
spin_lock_irqsave(&mod->lock, flags); |
| 643 |
|
| 644 |
if (mod->iftype == 0) |
| 645 |
ret = ican3_old_recv_msg(mod, msg); |
| 646 |
else |
| 647 |
ret = ican3_new_recv_msg(mod, msg); |
| 648 |
|
| 649 |
spin_unlock_irqrestore(&mod->lock, flags); |
| 650 |
return ret; |
| 651 |
} |
| 652 |
|
| 653 |
/* |
| 654 |
* Quick Pre-constructed Messages |
| 655 |
*/ |
| 656 |
|
| 657 |
static int ican3_msg_connect(struct ican3_dev *mod) |
| 658 |
{ |
| 659 |
struct ican3_msg msg; |
| 660 |
|
| 661 |
memset(&msg, 0, sizeof(msg)); |
| 662 |
msg.spec = MSG_CONNECTI; |
| 663 |
msg.len = cpu_to_le16(0); |
| 664 |
|
| 665 |
return ican3_send_msg(mod, &msg); |
| 666 |
} |
| 667 |
|
| 668 |
static int ican3_msg_disconnect(struct ican3_dev *mod) |
| 669 |
{ |
| 670 |
struct ican3_msg msg; |
| 671 |
|
| 672 |
memset(&msg, 0, sizeof(msg)); |
| 673 |
msg.spec = MSG_DISCONNECT; |
| 674 |
msg.len = cpu_to_le16(0); |
| 675 |
|
| 676 |
return ican3_send_msg(mod, &msg); |
| 677 |
} |
| 678 |
|
| 679 |
static int ican3_msg_newhostif(struct ican3_dev *mod) |
| 680 |
{ |
| 681 |
struct ican3_msg msg; |
| 682 |
int ret; |
| 683 |
|
| 684 |
memset(&msg, 0, sizeof(msg)); |
| 685 |
msg.spec = MSG_NEWHOSTIF; |
| 686 |
msg.len = cpu_to_le16(0); |
| 687 |
|
| 688 |
/* If we're not using the old interface, switching seems bogus */ |
| 689 |
WARN_ON(mod->iftype != 0); |
| 690 |
|
| 691 |
ret = ican3_send_msg(mod, &msg); |
| 692 |
if (ret) |
| 693 |
return ret; |
| 694 |
|
| 695 |
/* mark the module as using the new host interface */ |
| 696 |
mod->iftype = 1; |
| 697 |
return 0; |
| 698 |
} |
| 699 |
|
| 700 |
static int ican3_msg_fasthostif(struct ican3_dev *mod) |
| 701 |
{ |
| 702 |
struct ican3_msg msg; |
| 703 |
unsigned int addr; |
| 704 |
|
| 705 |
memset(&msg, 0, sizeof(msg)); |
| 706 |
msg.spec = MSG_INITFDPMQUEUE; |
| 707 |
msg.len = cpu_to_le16(8); |
| 708 |
|
| 709 |
/* write the tohost queue start address */ |
| 710 |
addr = DPM_PAGE_ADDR(mod->fastrx_start); |
| 711 |
msg.data[0] = addr & 0xff; |
| 712 |
msg.data[1] = (addr >> 8) & 0xff; |
| 713 |
msg.data[2] = (addr >> 16) & 0xff; |
| 714 |
msg.data[3] = (addr >> 24) & 0xff; |
| 715 |
|
| 716 |
/* write the fromhost queue start address */ |
| 717 |
addr = DPM_PAGE_ADDR(mod->fasttx_start); |
| 718 |
msg.data[4] = addr & 0xff; |
| 719 |
msg.data[5] = (addr >> 8) & 0xff; |
| 720 |
msg.data[6] = (addr >> 16) & 0xff; |
| 721 |
msg.data[7] = (addr >> 24) & 0xff; |
| 722 |
|
| 723 |
/* If we're not using the new interface yet, we cannot do this */ |
| 724 |
WARN_ON(mod->iftype != 1); |
| 725 |
|
| 726 |
return ican3_send_msg(mod, &msg); |
| 727 |
} |
| 728 |
|
| 729 |
/* |
| 730 |
* Setup the CAN filter to either accept or reject all |
| 731 |
* messages from the CAN bus. |
| 732 |
*/ |
| 733 |
static int ican3_set_id_filter(struct ican3_dev *mod, bool accept) |
| 734 |
{ |
| 735 |
struct ican3_msg msg; |
| 736 |
int ret; |
| 737 |
|
| 738 |
/* Standard Frame Format */ |
| 739 |
memset(&msg, 0, sizeof(msg)); |
| 740 |
msg.spec = MSG_SETAFILMASK; |
| 741 |
msg.len = cpu_to_le16(5); |
| 742 |
msg.data[0] = 0x00; /* IDLo LSB */ |
| 743 |
msg.data[1] = 0x00; /* IDLo MSB */ |
| 744 |
msg.data[2] = 0xff; /* IDHi LSB */ |
| 745 |
msg.data[3] = 0x07; /* IDHi MSB */ |
| 746 |
|
| 747 |
/* accept all frames for fast host if, or reject all frames */ |
| 748 |
msg.data[4] = accept ? SETAFILMASK_FASTIF : SETAFILMASK_REJECT; |
| 749 |
|
| 750 |
ret = ican3_send_msg(mod, &msg); |
| 751 |
if (ret) |
| 752 |
return ret; |
| 753 |
|
| 754 |
/* Extended Frame Format */ |
| 755 |
memset(&msg, 0, sizeof(msg)); |
| 756 |
msg.spec = MSG_SETAFILMASK; |
| 757 |
msg.len = cpu_to_le16(13); |
| 758 |
msg.data[0] = 0; /* MUX = 0 */ |
| 759 |
msg.data[1] = 0x00; /* IDLo LSB */ |
| 760 |
msg.data[2] = 0x00; |
| 761 |
msg.data[3] = 0x00; |
| 762 |
msg.data[4] = 0x20; /* IDLo MSB */ |
| 763 |
msg.data[5] = 0xff; /* IDHi LSB */ |
| 764 |
msg.data[6] = 0xff; |
| 765 |
msg.data[7] = 0xff; |
| 766 |
msg.data[8] = 0x3f; /* IDHi MSB */ |
| 767 |
|
| 768 |
/* accept all frames for fast host if, or reject all frames */ |
| 769 |
msg.data[9] = accept ? SETAFILMASK_FASTIF : SETAFILMASK_REJECT; |
| 770 |
|
| 771 |
return ican3_send_msg(mod, &msg); |
| 772 |
} |
| 773 |
|
| 774 |
/* |
| 775 |
* Bring the CAN bus online or offline |
| 776 |
*/ |
| 777 |
static int ican3_set_bus_state(struct ican3_dev *mod, bool on) |
| 778 |
{ |
| 779 |
struct can_bittiming *bt = &mod->can.bittiming; |
| 780 |
struct ican3_msg msg; |
| 781 |
u8 btr0, btr1; |
| 782 |
int res; |
| 783 |
|
| 784 |
/* This algorithm was stolen from drivers/net/can/sja1000/sja1000.c */ |
| 785 |
/* The bittiming register command for the ICAN3 just sets the bit timing */ |
| 786 |
/* registers on the SJA1000 chip directly */ |
| 787 |
btr0 = ((bt->brp - 1) & 0x3f) | (((bt->sjw - 1) & 0x3) << 6); |
| 788 |
btr1 = ((bt->prop_seg + bt->phase_seg1 - 1) & 0xf) | |
| 789 |
(((bt->phase_seg2 - 1) & 0x7) << 4); |
| 790 |
if (mod->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) |
| 791 |
btr1 |= 0x80; |
| 792 |
|
| 793 |
if (mod->fwtype == ICAN3_FWTYPE_ICANOS) { |
| 794 |
if (on) { |
| 795 |
/* set bittiming */ |
| 796 |
memset(&msg, 0, sizeof(msg)); |
| 797 |
msg.spec = MSG_CBTRREQ; |
| 798 |
msg.len = cpu_to_le16(4); |
| 799 |
msg.data[0] = 0x00; |
| 800 |
msg.data[1] = 0x00; |
| 801 |
msg.data[2] = btr0; |
| 802 |
msg.data[3] = btr1; |
| 803 |
|
| 804 |
res = ican3_send_msg(mod, &msg); |
| 805 |
if (res) |
| 806 |
return res; |
| 807 |
} |
| 808 |
|
| 809 |
/* can-on/off request */ |
| 810 |
memset(&msg, 0, sizeof(msg)); |
| 811 |
msg.spec = on ? MSG_CONREQ : MSG_COFFREQ; |
| 812 |
msg.len = cpu_to_le16(0); |
| 813 |
|
| 814 |
return ican3_send_msg(mod, &msg); |
| 815 |
|
| 816 |
} else if (mod->fwtype == ICAN3_FWTYPE_CAL_CANOPEN) { |
| 817 |
/* bittiming + can-on/off request */ |
| 818 |
memset(&msg, 0, sizeof(msg)); |
| 819 |
msg.spec = MSG_LMTS; |
| 820 |
if (on) { |
| 821 |
msg.len = cpu_to_le16(4); |
| 822 |
msg.data[0] = LMTS_BUSON_REQ; |
| 823 |
msg.data[1] = 0; |
| 824 |
msg.data[2] = btr0; |
| 825 |
msg.data[3] = btr1; |
| 826 |
} else { |
| 827 |
msg.len = cpu_to_le16(2); |
| 828 |
msg.data[0] = LMTS_BUSOFF_REQ; |
| 829 |
msg.data[1] = 0; |
| 830 |
} |
| 831 |
res = ican3_send_msg(mod, &msg); |
| 832 |
if (res) |
| 833 |
return res; |
| 834 |
|
| 835 |
if (on) { |
| 836 |
/* create NMT Slave Node for error processing |
| 837 |
* class 2 (with error capability, see CiA/DS203-1) |
| 838 |
* id 1 |
| 839 |
* name locnod1 (must be exactly 7 bytes) |
| 840 |
*/ |
| 841 |
memset(&msg, 0, sizeof(msg)); |
| 842 |
msg.spec = MSG_NMTS; |
| 843 |
msg.len = cpu_to_le16(11); |
| 844 |
msg.data[0] = NMTS_CREATE_NODE_REQ; |
| 845 |
msg.data[1] = 0; |
| 846 |
msg.data[2] = 2; /* node class */ |
| 847 |
msg.data[3] = 1; /* node id */ |
| 848 |
strcpy(msg.data + 4, "locnod1"); /* node name */ |
| 849 |
return ican3_send_msg(mod, &msg); |
| 850 |
} |
| 851 |
return 0; |
| 852 |
} |
| 853 |
return -ENOTSUPP; |
| 854 |
} |
| 855 |
|
| 856 |
static int ican3_set_termination(struct ican3_dev *mod, bool on) |
| 857 |
{ |
| 858 |
struct ican3_msg msg; |
| 859 |
|
| 860 |
memset(&msg, 0, sizeof(msg)); |
| 861 |
msg.spec = MSG_HWCONF; |
| 862 |
msg.len = cpu_to_le16(2); |
| 863 |
msg.data[0] = 0x00; |
| 864 |
msg.data[1] = on ? HWCONF_TERMINATE_ON : HWCONF_TERMINATE_OFF; |
| 865 |
|
| 866 |
return ican3_send_msg(mod, &msg); |
| 867 |
} |
| 868 |
|
| 869 |
static int ican3_send_inquiry(struct ican3_dev *mod, u8 subspec) |
| 870 |
{ |
| 871 |
struct ican3_msg msg; |
| 872 |
|
| 873 |
memset(&msg, 0, sizeof(msg)); |
| 874 |
msg.spec = MSG_INQUIRY; |
| 875 |
msg.len = cpu_to_le16(2); |
| 876 |
msg.data[0] = subspec; |
| 877 |
msg.data[1] = 0x00; |
| 878 |
|
| 879 |
return ican3_send_msg(mod, &msg); |
| 880 |
} |
| 881 |
|
| 882 |
static int ican3_set_buserror(struct ican3_dev *mod, u8 quota) |
| 883 |
{ |
| 884 |
struct ican3_msg msg; |
| 885 |
|
| 886 |
if (mod->fwtype == ICAN3_FWTYPE_ICANOS) { |
| 887 |
memset(&msg, 0, sizeof(msg)); |
| 888 |
msg.spec = MSG_CCONFREQ; |
| 889 |
msg.len = cpu_to_le16(2); |
| 890 |
msg.data[0] = 0x00; |
| 891 |
msg.data[1] = quota; |
| 892 |
} else if (mod->fwtype == ICAN3_FWTYPE_CAL_CANOPEN) { |
| 893 |
memset(&msg, 0, sizeof(msg)); |
| 894 |
msg.spec = MSG_LMTS; |
| 895 |
msg.len = cpu_to_le16(4); |
| 896 |
msg.data[0] = LMTS_CAN_CONF_REQ; |
| 897 |
msg.data[1] = 0x00; |
| 898 |
msg.data[2] = 0x00; |
| 899 |
msg.data[3] = quota; |
| 900 |
} else { |
| 901 |
return -ENOTSUPP; |
| 902 |
} |
| 903 |
return ican3_send_msg(mod, &msg); |
| 904 |
} |
| 905 |
|
| 906 |
/* |
| 907 |
* ICAN3 to Linux CAN Frame Conversion |
| 908 |
*/ |
| 909 |
|
| 910 |
static void ican3_to_can_frame(struct ican3_dev *mod, |
| 911 |
struct ican3_fast_desc *desc, |
| 912 |
struct can_frame *cf) |
| 913 |
{ |
| 914 |
if ((desc->command & ICAN3_CAN_TYPE_MASK) == ICAN3_CAN_TYPE_SFF) { |
| 915 |
if (desc->data[1] & ICAN3_SFF_RTR) |
| 916 |
cf->can_id |= CAN_RTR_FLAG; |
| 917 |
|
| 918 |
cf->can_id |= desc->data[0] << 3; |
| 919 |
cf->can_id |= (desc->data[1] & 0xe0) >> 5; |
| 920 |
cf->len = can_cc_dlc2len(desc->data[1] & ICAN3_CAN_DLC_MASK); |
| 921 |
memcpy(cf->data, &desc->data[2], cf->len); |
| 922 |
} else { |
| 923 |
cf->len = can_cc_dlc2len(desc->data[0] & ICAN3_CAN_DLC_MASK); |
| 924 |
if (desc->data[0] & ICAN3_EFF_RTR) |
| 925 |
cf->can_id |= CAN_RTR_FLAG; |
| 926 |
|
| 927 |
if (desc->data[0] & ICAN3_EFF) { |
| 928 |
cf->can_id |= CAN_EFF_FLAG; |
| 929 |
cf->can_id |= desc->data[2] << 21; /* 28-21 */ |
| 930 |
cf->can_id |= desc->data[3] << 13; /* 20-13 */ |
| 931 |
cf->can_id |= desc->data[4] << 5; /* 12-5 */ |
| 932 |
cf->can_id |= (desc->data[5] & 0xf8) >> 3; |
| 933 |
} else { |
| 934 |
cf->can_id |= desc->data[2] << 3; /* 10-3 */ |
| 935 |
cf->can_id |= desc->data[3] >> 5; /* 2-0 */ |
| 936 |
} |
| 937 |
|
| 938 |
memcpy(cf->data, &desc->data[6], cf->len); |
| 939 |
} |
| 940 |
} |
| 941 |
|
| 942 |
static void can_frame_to_ican3(struct ican3_dev *mod, |
| 943 |
struct can_frame *cf, |
| 944 |
struct ican3_fast_desc *desc) |
| 945 |
{ |
| 946 |
/* clear out any stale data in the descriptor */ |
| 947 |
memset(desc->data, 0, sizeof(desc->data)); |
| 948 |
|
| 949 |
/* we always use the extended format, with the ECHO flag set */ |
| 950 |
desc->command = ICAN3_CAN_TYPE_EFF; |
| 951 |
desc->data[0] |= cf->len; |
| 952 |
desc->data[1] |= ICAN3_ECHO; |
| 953 |
|
| 954 |
/* support single transmission (no retries) mode */ |
| 955 |
if (mod->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT) |
| 956 |
desc->data[1] |= ICAN3_SNGL; |
| 957 |
|
| 958 |
if (cf->can_id & CAN_RTR_FLAG) |
| 959 |
desc->data[0] |= ICAN3_EFF_RTR; |
| 960 |
|
| 961 |
/* pack the id into the correct places */ |
| 962 |
if (cf->can_id & CAN_EFF_FLAG) { |
| 963 |
desc->data[0] |= ICAN3_EFF; |
| 964 |
desc->data[2] = (cf->can_id & 0x1fe00000) >> 21; /* 28-21 */ |
| 965 |
desc->data[3] = (cf->can_id & 0x001fe000) >> 13; /* 20-13 */ |
| 966 |
desc->data[4] = (cf->can_id & 0x00001fe0) >> 5; /* 12-5 */ |
| 967 |
desc->data[5] = (cf->can_id & 0x0000001f) << 3; /* 4-0 */ |
| 968 |
} else { |
| 969 |
desc->data[2] = (cf->can_id & 0x7F8) >> 3; /* bits 10-3 */ |
| 970 |
desc->data[3] = (cf->can_id & 0x007) << 5; /* bits 2-0 */ |
| 971 |
} |
| 972 |
|
| 973 |
/* copy the data bits into the descriptor */ |
| 974 |
memcpy(&desc->data[6], cf->data, cf->len); |
| 975 |
} |
| 976 |
|
| 977 |
/* |
| 978 |
* Interrupt Handling |
| 979 |
*/ |
| 980 |
|
| 981 |
/* |
| 982 |
* Handle an ID + Version message response from the firmware. We never generate |
| 983 |
* this message in production code, but it is very useful when debugging to be |
| 984 |
* able to display this message. |
| 985 |
*/ |
| 986 |
static void ican3_handle_idvers(struct ican3_dev *mod, struct ican3_msg *msg) |
| 987 |
{ |
| 988 |
netdev_dbg(mod->ndev, "IDVERS response: %s\n", msg->data); |
| 989 |
} |
| 990 |
|
| 991 |
static void ican3_handle_msglost(struct ican3_dev *mod, struct ican3_msg *msg) |
| 992 |
{ |
| 993 |
struct net_device *dev = mod->ndev; |
| 994 |
struct net_device_stats *stats = &dev->stats; |
| 995 |
struct can_frame *cf; |
| 996 |
struct sk_buff *skb; |
| 997 |
|
| 998 |
/* |
| 999 |
* Report that communication messages with the microcontroller firmware |
| 1000 |
* are being lost. These are never CAN frames, so we do not generate an |
| 1001 |
* error frame for userspace |
| 1002 |
*/ |
| 1003 |
if (msg->spec == MSG_MSGLOST) { |
| 1004 |
netdev_err(mod->ndev, "lost %d control messages\n", msg->data[0]); |
| 1005 |
return; |
| 1006 |
} |
| 1007 |
|
| 1008 |
/* |
| 1009 |
* Oops, this indicates that we have lost messages in the fast queue, |
| 1010 |
* which are exclusively CAN messages. Our driver isn't reading CAN |
| 1011 |
* frames fast enough. |
| 1012 |
* |
| 1013 |
* We'll pretend that the SJA1000 told us that it ran out of buffer |
| 1014 |
* space, because there is not a better message for this. |
| 1015 |
*/ |
| 1016 |
skb = alloc_can_err_skb(dev, &cf); |
| 1017 |
if (skb) { |
| 1018 |
cf->can_id |= CAN_ERR_CRTL; |
| 1019 |
cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; |
| 1020 |
stats->rx_over_errors++; |
| 1021 |
stats->rx_errors++; |
| 1022 |
netif_rx(skb); |
| 1023 |
} |
| 1024 |
} |
| 1025 |
|
| 1026 |
/* |
| 1027 |
* Handle CAN Event Indication Messages from the firmware |
| 1028 |
* |
| 1029 |
* The ICAN3 firmware provides the values of some SJA1000 registers when it |
| 1030 |
* generates this message. The code below is largely copied from the |
| 1031 |
* drivers/net/can/sja1000/sja1000.c file, and adapted as necessary |
| 1032 |
*/ |
| 1033 |
static int ican3_handle_cevtind(struct ican3_dev *mod, struct ican3_msg *msg) |
| 1034 |
{ |
| 1035 |
struct net_device *dev = mod->ndev; |
| 1036 |
struct net_device_stats *stats = &dev->stats; |
| 1037 |
enum can_state state = mod->can.state; |
| 1038 |
u8 isrc, ecc, status, rxerr, txerr; |
| 1039 |
struct can_frame *cf; |
| 1040 |
struct sk_buff *skb; |
| 1041 |
|
| 1042 |
/* we can only handle the SJA1000 part */ |
| 1043 |
if (msg->data[1] != CEVTIND_CHIP_SJA1000) { |
| 1044 |
netdev_err(mod->ndev, "unable to handle errors on non-SJA1000\n"); |
| 1045 |
return -ENODEV; |
| 1046 |
} |
| 1047 |
|
| 1048 |
/* check the message length for sanity */ |
| 1049 |
if (le16_to_cpu(msg->len) < 6) { |
| 1050 |
netdev_err(mod->ndev, "error message too short\n"); |
| 1051 |
return -EINVAL; |
| 1052 |
} |
| 1053 |
|
| 1054 |
isrc = msg->data[0]; |
| 1055 |
ecc = msg->data[2]; |
| 1056 |
status = msg->data[3]; |
| 1057 |
rxerr = msg->data[4]; |
| 1058 |
txerr = msg->data[5]; |
| 1059 |
|
| 1060 |
/* |
| 1061 |
* This hardware lacks any support other than bus error messages to |
| 1062 |
* determine if packet transmission has failed. |
| 1063 |
* |
| 1064 |
* When TX errors happen, one echo skb needs to be dropped from the |
| 1065 |
* front of the queue. |
| 1066 |
* |
| 1067 |
* A small bit of code is duplicated here and below, to avoid error |
| 1068 |
* skb allocation when it will just be freed immediately. |
| 1069 |
*/ |
| 1070 |
if (isrc == CEVTIND_BEI) { |
| 1071 |
int ret; |
| 1072 |
netdev_dbg(mod->ndev, "bus error interrupt\n"); |
| 1073 |
|
| 1074 |
/* TX error */ |
| 1075 |
if (!(ecc & ECC_DIR)) { |
| 1076 |
kfree_skb(skb_dequeue(&mod->echoq)); |
| 1077 |
stats->tx_errors++; |
| 1078 |
} else { |
| 1079 |
stats->rx_errors++; |
| 1080 |
} |
| 1081 |
|
| 1082 |
/* |
| 1083 |
* The controller automatically disables bus-error interrupts |
| 1084 |
* and therefore we must re-enable them. |
| 1085 |
*/ |
| 1086 |
ret = ican3_set_buserror(mod, 1); |
| 1087 |
if (ret) { |
| 1088 |
netdev_err(mod->ndev, "unable to re-enable bus-error\n"); |
| 1089 |
return ret; |
| 1090 |
} |
| 1091 |
|
| 1092 |
/* bus error reporting is off, return immediately */ |
| 1093 |
if (!(mod->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)) |
| 1094 |
return 0; |
| 1095 |
} |
| 1096 |
|
| 1097 |
skb = alloc_can_err_skb(dev, &cf); |
| 1098 |
if (skb == NULL) |
| 1099 |
return -ENOMEM; |
| 1100 |
|
| 1101 |
/* data overrun interrupt */ |
| 1102 |
if (isrc == CEVTIND_DOI || isrc == CEVTIND_LOST) { |
| 1103 |
netdev_dbg(mod->ndev, "data overrun interrupt\n"); |
| 1104 |
cf->can_id |= CAN_ERR_CRTL; |
| 1105 |
cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; |
| 1106 |
stats->rx_over_errors++; |
| 1107 |
stats->rx_errors++; |
| 1108 |
} |
| 1109 |
|
| 1110 |
/* error warning + passive interrupt */ |
| 1111 |
if (isrc == CEVTIND_EI) { |
| 1112 |
netdev_dbg(mod->ndev, "error warning + passive interrupt\n"); |
| 1113 |
if (status & SR_BS) { |
| 1114 |
state = CAN_STATE_BUS_OFF; |
| 1115 |
cf->can_id |= CAN_ERR_BUSOFF; |
| 1116 |
mod->can.can_stats.bus_off++; |
| 1117 |
can_bus_off(dev); |
| 1118 |
} else if (status & SR_ES) { |
| 1119 |
if (rxerr >= 128 || txerr >= 128) |
| 1120 |
state = CAN_STATE_ERROR_PASSIVE; |
| 1121 |
else |
| 1122 |
state = CAN_STATE_ERROR_WARNING; |
| 1123 |
} else { |
| 1124 |
state = CAN_STATE_ERROR_ACTIVE; |
| 1125 |
} |
| 1126 |
} |
| 1127 |
|
| 1128 |
/* bus error interrupt */ |
| 1129 |
if (isrc == CEVTIND_BEI) { |
| 1130 |
mod->can.can_stats.bus_error++; |
| 1131 |
cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR | CAN_ERR_CNT; |
| 1132 |
|
| 1133 |
switch (ecc & ECC_MASK) { |
| 1134 |
case ECC_BIT: |
| 1135 |
cf->data[2] |= CAN_ERR_PROT_BIT; |
| 1136 |
break; |
| 1137 |
case ECC_FORM: |
| 1138 |
cf->data[2] |= CAN_ERR_PROT_FORM; |
| 1139 |
break; |
| 1140 |
case ECC_STUFF: |
| 1141 |
cf->data[2] |= CAN_ERR_PROT_STUFF; |
| 1142 |
break; |
| 1143 |
default: |
| 1144 |
cf->data[3] = ecc & ECC_SEG; |
| 1145 |
break; |
| 1146 |
} |
| 1147 |
|
| 1148 |
if (!(ecc & ECC_DIR)) |
| 1149 |
cf->data[2] |= CAN_ERR_PROT_TX; |
| 1150 |
|
| 1151 |
cf->data[6] = txerr; |
| 1152 |
cf->data[7] = rxerr; |
| 1153 |
} |
| 1154 |
|
| 1155 |
if (state != mod->can.state && (state == CAN_STATE_ERROR_WARNING || |
| 1156 |
state == CAN_STATE_ERROR_PASSIVE)) { |
| 1157 |
cf->can_id |= CAN_ERR_CRTL | CAN_ERR_CNT; |
| 1158 |
if (state == CAN_STATE_ERROR_WARNING) { |
| 1159 |
mod->can.can_stats.error_warning++; |
| 1160 |
cf->data[1] = (txerr > rxerr) ? |
| 1161 |
CAN_ERR_CRTL_TX_WARNING : |
| 1162 |
CAN_ERR_CRTL_RX_WARNING; |
| 1163 |
} else { |
| 1164 |
mod->can.can_stats.error_passive++; |
| 1165 |
cf->data[1] = (txerr > rxerr) ? |
| 1166 |
CAN_ERR_CRTL_TX_PASSIVE : |
| 1167 |
CAN_ERR_CRTL_RX_PASSIVE; |
| 1168 |
} |
| 1169 |
|
| 1170 |
cf->data[6] = txerr; |
| 1171 |
cf->data[7] = rxerr; |
| 1172 |
} |
| 1173 |
|
| 1174 |
mod->can.state = state; |
| 1175 |
netif_rx(skb); |
| 1176 |
return 0; |
| 1177 |
} |
| 1178 |
|
| 1179 |
static void ican3_handle_inquiry(struct ican3_dev *mod, struct ican3_msg *msg) |
| 1180 |
{ |
| 1181 |
switch (msg->data[0]) { |
| 1182 |
case INQUIRY_STATUS: |
| 1183 |
case INQUIRY_EXTENDED: |
| 1184 |
mod->bec.rxerr = msg->data[5]; |
| 1185 |
mod->bec.txerr = msg->data[6]; |
| 1186 |
complete(&mod->buserror_comp); |
| 1187 |
break; |
| 1188 |
case INQUIRY_TERMINATION: |
| 1189 |
mod->termination_enabled = msg->data[6] & HWCONF_TERMINATE_ON; |
| 1190 |
complete(&mod->termination_comp); |
| 1191 |
break; |
| 1192 |
default: |
| 1193 |
netdev_err(mod->ndev, "received an unknown inquiry response\n"); |
| 1194 |
break; |
| 1195 |
} |
| 1196 |
} |
| 1197 |
|
| 1198 |
/* Handle NMTS Slave Event Indication Messages from the firmware */ |
| 1199 |
static void ican3_handle_nmtsind(struct ican3_dev *mod, struct ican3_msg *msg) |
| 1200 |
{ |
| 1201 |
u16 subspec; |
| 1202 |
|
| 1203 |
subspec = msg->data[0] + msg->data[1] * 0x100; |
| 1204 |
if (subspec == NMTS_SLAVE_EVENT_IND) { |
| 1205 |
switch (msg->data[2]) { |
| 1206 |
case NE_LOCAL_OCCURRED: |
| 1207 |
case NE_LOCAL_RESOLVED: |
| 1208 |
/* now follows the same message as Raw ICANOS CEVTIND |
| 1209 |
* shift the data at the same place and call this method |
| 1210 |
*/ |
| 1211 |
le16_add_cpu(&msg->len, -3); |
| 1212 |
memmove(msg->data, msg->data + 3, le16_to_cpu(msg->len)); |
| 1213 |
ican3_handle_cevtind(mod, msg); |
| 1214 |
break; |
| 1215 |
case NE_REMOTE_OCCURRED: |
| 1216 |
case NE_REMOTE_RESOLVED: |
| 1217 |
/* should not occurre, ignore */ |
| 1218 |
break; |
| 1219 |
default: |
| 1220 |
netdev_warn(mod->ndev, "unknown NMTS event indication %x\n", |
| 1221 |
msg->data[2]); |
| 1222 |
break; |
| 1223 |
} |
| 1224 |
} else if (subspec == NMTS_SLAVE_STATE_IND) { |
| 1225 |
/* ignore state indications */ |
| 1226 |
} else { |
| 1227 |
netdev_warn(mod->ndev, "unhandled NMTS indication %x\n", |
| 1228 |
subspec); |
| 1229 |
return; |
| 1230 |
} |
| 1231 |
} |
| 1232 |
|
| 1233 |
static void ican3_handle_unknown_message(struct ican3_dev *mod, |
| 1234 |
struct ican3_msg *msg) |
| 1235 |
{ |
| 1236 |
netdev_warn(mod->ndev, "received unknown message: spec 0x%.2x length %d\n", |
| 1237 |
msg->spec, le16_to_cpu(msg->len)); |
| 1238 |
} |
| 1239 |
|
| 1240 |
/* |
| 1241 |
* Handle a control message from the firmware |
| 1242 |
*/ |
| 1243 |
static void ican3_handle_message(struct ican3_dev *mod, struct ican3_msg *msg) |
| 1244 |
{ |
| 1245 |
netdev_dbg(mod->ndev, "%s: modno %d spec 0x%.2x len %d bytes\n", __func__, |
| 1246 |
mod->num, msg->spec, le16_to_cpu(msg->len)); |
| 1247 |
|
| 1248 |
switch (msg->spec) { |
| 1249 |
case MSG_IDVERS: |
| 1250 |
ican3_handle_idvers(mod, msg); |
| 1251 |
break; |
| 1252 |
case MSG_MSGLOST: |
| 1253 |
case MSG_FMSGLOST: |
| 1254 |
ican3_handle_msglost(mod, msg); |
| 1255 |
break; |
| 1256 |
case MSG_CEVTIND: |
| 1257 |
ican3_handle_cevtind(mod, msg); |
| 1258 |
break; |
| 1259 |
case MSG_INQUIRY: |
| 1260 |
ican3_handle_inquiry(mod, msg); |
| 1261 |
break; |
| 1262 |
case MSG_NMTS: |
| 1263 |
ican3_handle_nmtsind(mod, msg); |
| 1264 |
break; |
| 1265 |
default: |
| 1266 |
ican3_handle_unknown_message(mod, msg); |
| 1267 |
break; |
| 1268 |
} |
| 1269 |
} |
| 1270 |
|
| 1271 |
/* |
| 1272 |
* The ican3 needs to store all echo skbs, and therefore cannot |
| 1273 |
* use the generic infrastructure for this. |
| 1274 |
*/ |
| 1275 |
static void ican3_put_echo_skb(struct ican3_dev *mod, struct sk_buff *skb) |
| 1276 |
{ |
| 1277 |
skb = can_create_echo_skb(skb); |
| 1278 |
if (!skb) |
| 1279 |
return; |
| 1280 |
|
| 1281 |
skb_tx_timestamp(skb); |
| 1282 |
|
| 1283 |
/* save this skb for tx interrupt echo handling */ |
| 1284 |
skb_queue_tail(&mod->echoq, skb); |
| 1285 |
} |
| 1286 |
|
| 1287 |
static unsigned int ican3_get_echo_skb(struct ican3_dev *mod) |
| 1288 |
{ |
| 1289 |
struct sk_buff *skb = skb_dequeue(&mod->echoq); |
| 1290 |
struct can_frame *cf; |
| 1291 |
u8 dlc = 0; |
| 1292 |
|
| 1293 |
/* this should never trigger unless there is a driver bug */ |
| 1294 |
if (!skb) { |
| 1295 |
netdev_err(mod->ndev, "BUG: echo skb not occupied\n"); |
| 1296 |
return 0; |
| 1297 |
} |
| 1298 |
|
| 1299 |
cf = (struct can_frame *)skb->data; |
| 1300 |
if (!(cf->can_id & CAN_RTR_FLAG)) |
| 1301 |
dlc = cf->len; |
| 1302 |
|
| 1303 |
/* check flag whether this packet has to be looped back */ |
| 1304 |
if (skb->pkt_type != PACKET_LOOPBACK) { |
| 1305 |
kfree_skb(skb); |
| 1306 |
return dlc; |
| 1307 |
} |
| 1308 |
|
| 1309 |
skb->protocol = htons(ETH_P_CAN); |
| 1310 |
skb->pkt_type = PACKET_BROADCAST; |
| 1311 |
skb->ip_summed = CHECKSUM_UNNECESSARY; |
| 1312 |
skb->dev = mod->ndev; |
| 1313 |
netif_receive_skb(skb); |
| 1314 |
return dlc; |
| 1315 |
} |
| 1316 |
|
| 1317 |
/* |
| 1318 |
* Compare an skb with an existing echo skb |
| 1319 |
* |
| 1320 |
* This function will be used on devices which have a hardware loopback. |
| 1321 |
* On these devices, this function can be used to compare a received skb |
| 1322 |
* with the saved echo skbs so that the hardware echo skb can be dropped. |
| 1323 |
* |
| 1324 |
* Returns true if the skb's are identical, false otherwise. |
| 1325 |
*/ |
| 1326 |
static bool ican3_echo_skb_matches(struct ican3_dev *mod, struct sk_buff *skb) |
| 1327 |
{ |
| 1328 |
struct can_frame *cf = (struct can_frame *)skb->data; |
| 1329 |
struct sk_buff *echo_skb = skb_peek(&mod->echoq); |
| 1330 |
struct can_frame *echo_cf; |
| 1331 |
|
| 1332 |
if (!echo_skb) |
| 1333 |
return false; |
| 1334 |
|
| 1335 |
echo_cf = (struct can_frame *)echo_skb->data; |
| 1336 |
if (cf->can_id != echo_cf->can_id) |
| 1337 |
return false; |
| 1338 |
|
| 1339 |
if (cf->len != echo_cf->len) |
| 1340 |
return false; |
| 1341 |
|
| 1342 |
return memcmp(cf->data, echo_cf->data, cf->len) == 0; |
| 1343 |
} |
| 1344 |
|
| 1345 |
/* |
| 1346 |
* Check that there is room in the TX ring to transmit another skb |
| 1347 |
* |
| 1348 |
* LOCKING: must hold mod->lock |
| 1349 |
*/ |
| 1350 |
static bool ican3_txok(struct ican3_dev *mod) |
| 1351 |
{ |
| 1352 |
struct ican3_fast_desc __iomem *desc; |
| 1353 |
u8 control; |
| 1354 |
|
| 1355 |
/* check that we have echo queue space */ |
| 1356 |
if (skb_queue_len(&mod->echoq) >= ICAN3_TX_BUFFERS) |
| 1357 |
return false; |
| 1358 |
|
| 1359 |
/* copy the control bits of the descriptor */ |
| 1360 |
ican3_set_page(mod, mod->fasttx_start + (mod->fasttx_num / 16)); |
| 1361 |
desc = mod->dpm + ((mod->fasttx_num % 16) * sizeof(*desc)); |
| 1362 |
control = ioread8(&desc->control); |
| 1363 |
|
| 1364 |
/* if the control bits are not valid, then we have no more space */ |
| 1365 |
if (!(control & DESC_VALID)) |
| 1366 |
return false; |
| 1367 |
|
| 1368 |
return true; |
| 1369 |
} |
| 1370 |
|
| 1371 |
/* |
| 1372 |
* Receive one CAN frame from the hardware |
| 1373 |
* |
| 1374 |
* CONTEXT: must be called from user context |
| 1375 |
*/ |
| 1376 |
static int ican3_recv_skb(struct ican3_dev *mod) |
| 1377 |
{ |
| 1378 |
struct net_device *ndev = mod->ndev; |
| 1379 |
struct net_device_stats *stats = &ndev->stats; |
| 1380 |
struct ican3_fast_desc desc; |
| 1381 |
void __iomem *desc_addr; |
| 1382 |
struct can_frame *cf; |
| 1383 |
struct sk_buff *skb; |
| 1384 |
unsigned long flags; |
| 1385 |
|
| 1386 |
spin_lock_irqsave(&mod->lock, flags); |
| 1387 |
|
| 1388 |
/* copy the whole descriptor */ |
| 1389 |
ican3_set_page(mod, mod->fastrx_start + (mod->fastrx_num / 16)); |
| 1390 |
desc_addr = mod->dpm + ((mod->fastrx_num % 16) * sizeof(desc)); |
| 1391 |
memcpy_fromio(&desc, desc_addr, sizeof(desc)); |
| 1392 |
|
| 1393 |
spin_unlock_irqrestore(&mod->lock, flags); |
| 1394 |
|
| 1395 |
/* check that we actually have a CAN frame */ |
| 1396 |
if (!(desc.control & DESC_VALID)) |
| 1397 |
return -ENOBUFS; |
| 1398 |
|
| 1399 |
/* allocate an skb */ |
| 1400 |
skb = alloc_can_skb(ndev, &cf); |
| 1401 |
if (unlikely(skb == NULL)) { |
| 1402 |
stats->rx_dropped++; |
| 1403 |
goto err_noalloc; |
| 1404 |
} |
| 1405 |
|
| 1406 |
/* convert the ICAN3 frame into Linux CAN format */ |
| 1407 |
ican3_to_can_frame(mod, &desc, cf); |
| 1408 |
|
| 1409 |
/* |
| 1410 |
* If this is an ECHO frame received from the hardware loopback |
| 1411 |
* feature, use the skb saved in the ECHO stack instead. This allows |
| 1412 |
* the Linux CAN core to support CAN_RAW_RECV_OWN_MSGS correctly. |
| 1413 |
* |
| 1414 |
* Since this is a confirmation of a successfully transmitted packet |
| 1415 |
* sent from this host, update the transmit statistics. |
| 1416 |
* |
| 1417 |
* Also, the netdevice queue needs to be allowed to send packets again. |
| 1418 |
*/ |
| 1419 |
if (ican3_echo_skb_matches(mod, skb)) { |
| 1420 |
stats->tx_packets++; |
| 1421 |
stats->tx_bytes += ican3_get_echo_skb(mod); |
| 1422 |
kfree_skb(skb); |
| 1423 |
goto err_noalloc; |
| 1424 |
} |
| 1425 |
|
| 1426 |
/* update statistics, receive the skb */ |
| 1427 |
stats->rx_packets++; |
| 1428 |
if (!(cf->can_id & CAN_RTR_FLAG)) |
| 1429 |
stats->rx_bytes += cf->len; |
| 1430 |
netif_receive_skb(skb); |
| 1431 |
|
| 1432 |
err_noalloc: |
| 1433 |
/* toggle the valid bit and return the descriptor to the ring */ |
| 1434 |
desc.control ^= DESC_VALID; |
| 1435 |
|
| 1436 |
spin_lock_irqsave(&mod->lock, flags); |
| 1437 |
|
| 1438 |
ican3_set_page(mod, mod->fastrx_start + (mod->fastrx_num / 16)); |
| 1439 |
memcpy_toio(desc_addr, &desc, 1); |
| 1440 |
|
| 1441 |
/* update the next buffer pointer */ |
| 1442 |
mod->fastrx_num = (desc.control & DESC_WRAP) ? 0 |
| 1443 |
: (mod->fastrx_num + 1); |
| 1444 |
|
| 1445 |
/* there are still more buffers to process */ |
| 1446 |
spin_unlock_irqrestore(&mod->lock, flags); |
| 1447 |
return 0; |
| 1448 |
} |
| 1449 |
|
| 1450 |
static int ican3_napi(struct napi_struct *napi, int budget) |
| 1451 |
{ |
| 1452 |
struct ican3_dev *mod = container_of(napi, struct ican3_dev, napi); |
| 1453 |
unsigned long flags; |
| 1454 |
int received = 0; |
| 1455 |
int ret; |
| 1456 |
|
| 1457 |
/* process all communication messages */ |
| 1458 |
while (true) { |
| 1459 |
struct ican3_msg msg; |
| 1460 |
ret = ican3_recv_msg(mod, &msg); |
| 1461 |
if (ret) |
| 1462 |
break; |
| 1463 |
|
| 1464 |
ican3_handle_message(mod, &msg); |
| 1465 |
} |
| 1466 |
|
| 1467 |
/* process all CAN frames from the fast interface */ |
| 1468 |
while (received < budget) { |
| 1469 |
ret = ican3_recv_skb(mod); |
| 1470 |
if (ret) |
| 1471 |
break; |
| 1472 |
|
| 1473 |
received++; |
| 1474 |
} |
| 1475 |
|
| 1476 |
/* We have processed all packets that the adapter had, but it |
| 1477 |
* was less than our budget, stop polling */ |
| 1478 |
if (received < budget) |
| 1479 |
napi_complete_done(napi, received); |
| 1480 |
|
| 1481 |
spin_lock_irqsave(&mod->lock, flags); |
| 1482 |
|
| 1483 |
/* Wake up the transmit queue if necessary */ |
| 1484 |
if (netif_queue_stopped(mod->ndev) && ican3_txok(mod)) |
| 1485 |
netif_wake_queue(mod->ndev); |
| 1486 |
|
| 1487 |
spin_unlock_irqrestore(&mod->lock, flags); |
| 1488 |
|
| 1489 |
/* re-enable interrupt generation */ |
| 1490 |
iowrite8(1 << mod->num, &mod->ctrl->int_enable); |
| 1491 |
return received; |
| 1492 |
} |
| 1493 |
|
| 1494 |
static irqreturn_t ican3_irq(int irq, void *dev_id) |
| 1495 |
{ |
| 1496 |
struct ican3_dev *mod = dev_id; |
| 1497 |
u8 stat; |
| 1498 |
|
| 1499 |
/* |
| 1500 |
* The interrupt status register on this device reports interrupts |
| 1501 |
* as zeroes instead of using ones like most other devices |
| 1502 |
*/ |
| 1503 |
stat = ioread8(&mod->ctrl->int_disable) & (1 << mod->num); |
| 1504 |
if (stat == (1 << mod->num)) |
| 1505 |
return IRQ_NONE; |
| 1506 |
|
| 1507 |
/* clear the MODULbus interrupt from the microcontroller */ |
| 1508 |
ioread8(&mod->dpmctrl->interrupt); |
| 1509 |
|
| 1510 |
/* disable interrupt generation, schedule the NAPI poller */ |
| 1511 |
iowrite8(1 << mod->num, &mod->ctrl->int_disable); |
| 1512 |
napi_schedule(&mod->napi); |
| 1513 |
return IRQ_HANDLED; |
| 1514 |
} |
| 1515 |
|
| 1516 |
/* |
| 1517 |
* Firmware reset, startup, and shutdown |
| 1518 |
*/ |
| 1519 |
|
| 1520 |
/* |
| 1521 |
* Reset an ICAN module to its power-on state |
| 1522 |
* |
| 1523 |
* CONTEXT: no network device registered |
| 1524 |
*/ |
| 1525 |
static int ican3_reset_module(struct ican3_dev *mod) |
| 1526 |
{ |
| 1527 |
unsigned long start; |
| 1528 |
u8 runold, runnew; |
| 1529 |
|
| 1530 |
/* disable interrupts so no more work is scheduled */ |
| 1531 |
iowrite8(1 << mod->num, &mod->ctrl->int_disable); |
| 1532 |
|
| 1533 |
/* the first unallocated page in the DPM is #9 */ |
| 1534 |
mod->free_page = DPM_FREE_START; |
| 1535 |
|
| 1536 |
ican3_set_page(mod, QUEUE_OLD_CONTROL); |
| 1537 |
runold = ioread8(mod->dpm + TARGET_RUNNING); |
| 1538 |
|
| 1539 |
/* reset the module */ |
| 1540 |
iowrite8(0x00, &mod->dpmctrl->hwreset); |
| 1541 |
|
| 1542 |
/* wait until the module has finished resetting and is running */ |
| 1543 |
start = jiffies; |
| 1544 |
do { |
| 1545 |
ican3_set_page(mod, QUEUE_OLD_CONTROL); |
| 1546 |
runnew = ioread8(mod->dpm + TARGET_RUNNING); |
| 1547 |
if (runnew == (runold ^ 0xff)) |
| 1548 |
return 0; |
| 1549 |
|
| 1550 |
msleep(10); |
| 1551 |
} while (time_before(jiffies, start + HZ / 2)); |
| 1552 |
|
| 1553 |
netdev_err(mod->ndev, "failed to reset CAN module\n"); |
| 1554 |
return -ETIMEDOUT; |
| 1555 |
} |
| 1556 |
|
| 1557 |
static void ican3_shutdown_module(struct ican3_dev *mod) |
| 1558 |
{ |
| 1559 |
ican3_msg_disconnect(mod); |
| 1560 |
ican3_reset_module(mod); |
| 1561 |
} |
| 1562 |
|
| 1563 |
/* |
| 1564 |
* Startup an ICAN module, bringing it into fast mode |
| 1565 |
*/ |
| 1566 |
static int ican3_startup_module(struct ican3_dev *mod) |
| 1567 |
{ |
| 1568 |
int ret; |
| 1569 |
|
| 1570 |
ret = ican3_reset_module(mod); |
| 1571 |
if (ret) { |
| 1572 |
netdev_err(mod->ndev, "unable to reset module\n"); |
| 1573 |
return ret; |
| 1574 |
} |
| 1575 |
|
| 1576 |
/* detect firmware */ |
| 1577 |
memcpy_fromio(mod->fwinfo, mod->dpm + FIRMWARE_STAMP, sizeof(mod->fwinfo) - 1); |
| 1578 |
if (strncmp(mod->fwinfo, "JANZ-ICAN3", 10)) { |
| 1579 |
netdev_err(mod->ndev, "ICAN3 not detected (found %s)\n", mod->fwinfo); |
| 1580 |
return -ENODEV; |
| 1581 |
} |
| 1582 |
if (strstr(mod->fwinfo, "CAL/CANopen")) |
| 1583 |
mod->fwtype = ICAN3_FWTYPE_CAL_CANOPEN; |
| 1584 |
else |
| 1585 |
mod->fwtype = ICAN3_FWTYPE_ICANOS; |
| 1586 |
|
| 1587 |
/* re-enable interrupts so we can send messages */ |
| 1588 |
iowrite8(1 << mod->num, &mod->ctrl->int_enable); |
| 1589 |
|
| 1590 |
ret = ican3_msg_connect(mod); |
| 1591 |
if (ret) { |
| 1592 |
netdev_err(mod->ndev, "unable to connect to module\n"); |
| 1593 |
return ret; |
| 1594 |
} |
| 1595 |
|
| 1596 |
ican3_init_new_host_interface(mod); |
| 1597 |
ret = ican3_msg_newhostif(mod); |
| 1598 |
if (ret) { |
| 1599 |
netdev_err(mod->ndev, "unable to switch to new-style interface\n"); |
| 1600 |
return ret; |
| 1601 |
} |
| 1602 |
|
| 1603 |
/* default to "termination on" */ |
| 1604 |
ret = ican3_set_termination(mod, true); |
| 1605 |
if (ret) { |
| 1606 |
netdev_err(mod->ndev, "unable to enable termination\n"); |
| 1607 |
return ret; |
| 1608 |
} |
| 1609 |
|
| 1610 |
/* default to "bus errors enabled" */ |
| 1611 |
ret = ican3_set_buserror(mod, 1); |
| 1612 |
if (ret) { |
| 1613 |
netdev_err(mod->ndev, "unable to set bus-error\n"); |
| 1614 |
return ret; |
| 1615 |
} |
| 1616 |
|
| 1617 |
ican3_init_fast_host_interface(mod); |
| 1618 |
ret = ican3_msg_fasthostif(mod); |
| 1619 |
if (ret) { |
| 1620 |
netdev_err(mod->ndev, "unable to switch to fast host interface\n"); |
| 1621 |
return ret; |
| 1622 |
} |
| 1623 |
|
| 1624 |
ret = ican3_set_id_filter(mod, true); |
| 1625 |
if (ret) { |
| 1626 |
netdev_err(mod->ndev, "unable to set acceptance filter\n"); |
| 1627 |
return ret; |
| 1628 |
} |
| 1629 |
|
| 1630 |
return 0; |
| 1631 |
} |
| 1632 |
|
| 1633 |
/* |
| 1634 |
* CAN Network Device |
| 1635 |
*/ |
| 1636 |
|
| 1637 |
static int ican3_open(struct net_device *ndev) |
| 1638 |
{ |
| 1639 |
struct ican3_dev *mod = netdev_priv(ndev); |
| 1640 |
int ret; |
| 1641 |
|
| 1642 |
/* open the CAN layer */ |
| 1643 |
ret = open_candev(ndev); |
| 1644 |
if (ret) { |
| 1645 |
netdev_err(mod->ndev, "unable to start CAN layer\n"); |
| 1646 |
return ret; |
| 1647 |
} |
| 1648 |
|
| 1649 |
/* bring the bus online */ |
| 1650 |
ret = ican3_set_bus_state(mod, true); |
| 1651 |
if (ret) { |
| 1652 |
netdev_err(mod->ndev, "unable to set bus-on\n"); |
| 1653 |
close_candev(ndev); |
| 1654 |
return ret; |
| 1655 |
} |
| 1656 |
|
| 1657 |
/* start up the network device */ |
| 1658 |
mod->can.state = CAN_STATE_ERROR_ACTIVE; |
| 1659 |
netif_start_queue(ndev); |
| 1660 |
|
| 1661 |
return 0; |
| 1662 |
} |
| 1663 |
|
| 1664 |
static int ican3_stop(struct net_device *ndev) |
| 1665 |
{ |
| 1666 |
struct ican3_dev *mod = netdev_priv(ndev); |
| 1667 |
int ret; |
| 1668 |
|
| 1669 |
/* stop the network device xmit routine */ |
| 1670 |
netif_stop_queue(ndev); |
| 1671 |
mod->can.state = CAN_STATE_STOPPED; |
| 1672 |
|
| 1673 |
/* bring the bus offline, stop receiving packets */ |
| 1674 |
ret = ican3_set_bus_state(mod, false); |
| 1675 |
if (ret) { |
| 1676 |
netdev_err(mod->ndev, "unable to set bus-off\n"); |
| 1677 |
return ret; |
| 1678 |
} |
| 1679 |
|
| 1680 |
/* drop all outstanding echo skbs */ |
| 1681 |
skb_queue_purge(&mod->echoq); |
| 1682 |
|
| 1683 |
/* close the CAN layer */ |
| 1684 |
close_candev(ndev); |
| 1685 |
return 0; |
| 1686 |
} |
| 1687 |
|
| 1688 |
static netdev_tx_t ican3_xmit(struct sk_buff *skb, struct net_device *ndev) |
| 1689 |
{ |
| 1690 |
struct ican3_dev *mod = netdev_priv(ndev); |
| 1691 |
struct can_frame *cf = (struct can_frame *)skb->data; |
| 1692 |
struct ican3_fast_desc desc; |
| 1693 |
void __iomem *desc_addr; |
| 1694 |
unsigned long flags; |
| 1695 |
|
| 1696 |
if (can_dev_dropped_skb(ndev, skb)) |
| 1697 |
return NETDEV_TX_OK; |
| 1698 |
|
| 1699 |
spin_lock_irqsave(&mod->lock, flags); |
| 1700 |
|
| 1701 |
/* check that we can actually transmit */ |
| 1702 |
if (!ican3_txok(mod)) { |
| 1703 |
netdev_err(mod->ndev, "BUG: no free descriptors\n"); |
| 1704 |
spin_unlock_irqrestore(&mod->lock, flags); |
| 1705 |
return NETDEV_TX_BUSY; |
| 1706 |
} |
| 1707 |
|
| 1708 |
/* copy the control bits of the descriptor */ |
| 1709 |
ican3_set_page(mod, mod->fasttx_start + (mod->fasttx_num / 16)); |
| 1710 |
desc_addr = mod->dpm + ((mod->fasttx_num % 16) * sizeof(desc)); |
| 1711 |
memset(&desc, 0, sizeof(desc)); |
| 1712 |
memcpy_fromio(&desc, desc_addr, 1); |
| 1713 |
|
| 1714 |
/* convert the Linux CAN frame into ICAN3 format */ |
| 1715 |
can_frame_to_ican3(mod, cf, &desc); |
| 1716 |
|
| 1717 |
/* |
| 1718 |
* This hardware doesn't have TX-done notifications, so we'll try and |
| 1719 |
* emulate it the best we can using ECHO skbs. Add the skb to the ECHO |
| 1720 |
* stack. Upon packet reception, check if the ECHO skb and received |
| 1721 |
* skb match, and use that to wake the queue. |
| 1722 |
*/ |
| 1723 |
ican3_put_echo_skb(mod, skb); |
| 1724 |
|
| 1725 |
/* |
| 1726 |
* the programming manual says that you must set the IVALID bit, then |
| 1727 |
* interrupt, then set the valid bit. Quite weird, but it seems to be |
| 1728 |
* required for this to work |
| 1729 |
*/ |
| 1730 |
desc.control |= DESC_IVALID; |
| 1731 |
memcpy_toio(desc_addr, &desc, sizeof(desc)); |
| 1732 |
|
| 1733 |
/* generate a MODULbus interrupt to the microcontroller */ |
| 1734 |
iowrite8(0x01, &mod->dpmctrl->interrupt); |
| 1735 |
|
| 1736 |
desc.control ^= DESC_VALID; |
| 1737 |
memcpy_toio(desc_addr, &desc, sizeof(desc)); |
| 1738 |
|
| 1739 |
/* update the next buffer pointer */ |
| 1740 |
mod->fasttx_num = (desc.control & DESC_WRAP) ? 0 |
| 1741 |
: (mod->fasttx_num + 1); |
| 1742 |
|
| 1743 |
/* if there is no free descriptor space, stop the transmit queue */ |
| 1744 |
if (!ican3_txok(mod)) |
| 1745 |
netif_stop_queue(ndev); |
| 1746 |
|
| 1747 |
spin_unlock_irqrestore(&mod->lock, flags); |
| 1748 |
return NETDEV_TX_OK; |
| 1749 |
} |
| 1750 |
|
| 1751 |
static const struct net_device_ops ican3_netdev_ops = { |
| 1752 |
.ndo_open = ican3_open, |
| 1753 |
.ndo_stop = ican3_stop, |
| 1754 |
.ndo_start_xmit = ican3_xmit, |
| 1755 |
}; |
| 1756 |
|
| 1757 |
static const struct ethtool_ops ican3_ethtool_ops = { |
| 1758 |
.get_ts_info = ethtool_op_get_ts_info, |
| 1759 |
}; |
| 1760 |
|
| 1761 |
/* |
| 1762 |
* Low-level CAN Device |
| 1763 |
*/ |
| 1764 |
|
| 1765 |
/* This structure was stolen from drivers/net/can/sja1000/sja1000.c */ |
| 1766 |
static const struct can_bittiming_const ican3_bittiming_const = { |
| 1767 |
.name = DRV_NAME, |
| 1768 |
.tseg1_min = 1, |
| 1769 |
.tseg1_max = 16, |
| 1770 |
.tseg2_min = 1, |
| 1771 |
.tseg2_max = 8, |
| 1772 |
.sjw_max = 4, |
| 1773 |
.brp_min = 1, |
| 1774 |
.brp_max = 64, |
| 1775 |
.brp_inc = 1, |
| 1776 |
}; |
| 1777 |
|
| 1778 |
static int ican3_set_mode(struct net_device *ndev, enum can_mode mode) |
| 1779 |
{ |
| 1780 |
struct ican3_dev *mod = netdev_priv(ndev); |
| 1781 |
int ret; |
| 1782 |
|
| 1783 |
if (mode != CAN_MODE_START) |
| 1784 |
return -ENOTSUPP; |
| 1785 |
|
| 1786 |
/* bring the bus online */ |
| 1787 |
ret = ican3_set_bus_state(mod, true); |
| 1788 |
if (ret) { |
| 1789 |
netdev_err(ndev, "unable to set bus-on\n"); |
| 1790 |
return ret; |
| 1791 |
} |
| 1792 |
|
| 1793 |
/* start up the network device */ |
| 1794 |
mod->can.state = CAN_STATE_ERROR_ACTIVE; |
| 1795 |
|
| 1796 |
if (netif_queue_stopped(ndev)) |
| 1797 |
netif_wake_queue(ndev); |
| 1798 |
|
| 1799 |
return 0; |
| 1800 |
} |
| 1801 |
|
| 1802 |
static int ican3_get_berr_counter(const struct net_device *ndev, |
| 1803 |
struct can_berr_counter *bec) |
| 1804 |
{ |
| 1805 |
struct ican3_dev *mod = netdev_priv(ndev); |
| 1806 |
int ret; |
| 1807 |
|
| 1808 |
ret = ican3_send_inquiry(mod, INQUIRY_STATUS); |
| 1809 |
if (ret) |
| 1810 |
return ret; |
| 1811 |
|
| 1812 |
if (!wait_for_completion_timeout(&mod->buserror_comp, HZ)) { |
| 1813 |
netdev_info(mod->ndev, "%s timed out\n", __func__); |
| 1814 |
return -ETIMEDOUT; |
| 1815 |
} |
| 1816 |
|
| 1817 |
bec->rxerr = mod->bec.rxerr; |
| 1818 |
bec->txerr = mod->bec.txerr; |
| 1819 |
return 0; |
| 1820 |
} |
| 1821 |
|
| 1822 |
/* |
| 1823 |
* Sysfs Attributes |
| 1824 |
*/ |
| 1825 |
|
| 1826 |
static ssize_t termination_show(struct device *dev, |
| 1827 |
struct device_attribute *attr, |
| 1828 |
char *buf) |
| 1829 |
{ |
| 1830 |
struct ican3_dev *mod = netdev_priv(to_net_dev(dev)); |
| 1831 |
int ret; |
| 1832 |
|
| 1833 |
ret = ican3_send_inquiry(mod, INQUIRY_TERMINATION); |
| 1834 |
if (ret) |
| 1835 |
return ret; |
| 1836 |
|
| 1837 |
if (!wait_for_completion_timeout(&mod->termination_comp, HZ)) { |
| 1838 |
netdev_info(mod->ndev, "%s timed out\n", __func__); |
| 1839 |
return -ETIMEDOUT; |
| 1840 |
} |
| 1841 |
|
| 1842 |
return sysfs_emit(buf, "%u\n", mod->termination_enabled); |
| 1843 |
} |
| 1844 |
|
| 1845 |
static ssize_t termination_store(struct device *dev, |
| 1846 |
struct device_attribute *attr, |
| 1847 |
const char *buf, size_t count) |
| 1848 |
{ |
| 1849 |
struct ican3_dev *mod = netdev_priv(to_net_dev(dev)); |
| 1850 |
unsigned long enable; |
| 1851 |
int ret; |
| 1852 |
|
| 1853 |
if (kstrtoul(buf, 0, &enable)) |
| 1854 |
return -EINVAL; |
| 1855 |
|
| 1856 |
ret = ican3_set_termination(mod, enable); |
| 1857 |
if (ret) |
| 1858 |
return ret; |
| 1859 |
|
| 1860 |
return count; |
| 1861 |
} |
| 1862 |
|
| 1863 |
static ssize_t fwinfo_show(struct device *dev, |
| 1864 |
struct device_attribute *attr, |
| 1865 |
char *buf) |
| 1866 |
{ |
| 1867 |
struct ican3_dev *mod = netdev_priv(to_net_dev(dev)); |
| 1868 |
|
| 1869 |
return sysfs_emit(buf, "%s\n", mod->fwinfo); |
| 1870 |
} |
| 1871 |
|
| 1872 |
static DEVICE_ATTR_RW(termination); |
| 1873 |
static DEVICE_ATTR_RO(fwinfo); |
| 1874 |
|
| 1875 |
static struct attribute *ican3_sysfs_attrs[] = { |
| 1876 |
&dev_attr_termination.attr, |
| 1877 |
&dev_attr_fwinfo.attr, |
| 1878 |
NULL, |
| 1879 |
}; |
| 1880 |
|
| 1881 |
static const struct attribute_group ican3_sysfs_attr_group = { |
| 1882 |
.attrs = ican3_sysfs_attrs, |
| 1883 |
}; |
| 1884 |
|
| 1885 |
/* |
| 1886 |
* PCI Subsystem |
| 1887 |
*/ |
| 1888 |
|
| 1889 |
static int ican3_probe(struct platform_device *pdev) |
| 1890 |
{ |
| 1891 |
struct janz_platform_data *pdata; |
| 1892 |
struct net_device *ndev; |
| 1893 |
struct ican3_dev *mod; |
| 1894 |
struct resource *res; |
| 1895 |
struct device *dev; |
| 1896 |
int ret; |
| 1897 |
|
| 1898 |
pdata = dev_get_platdata(&pdev->dev); |
| 1899 |
if (!pdata) |
| 1900 |
return -ENXIO; |
| 1901 |
|
| 1902 |
dev_dbg(&pdev->dev, "probe: module number %d\n", pdata->modno); |
| 1903 |
|
| 1904 |
/* save the struct device for printing */ |
| 1905 |
dev = &pdev->dev; |
| 1906 |
|
| 1907 |
/* allocate the CAN device and private data */ |
| 1908 |
ndev = alloc_candev(sizeof(*mod), 0); |
| 1909 |
if (!ndev) { |
| 1910 |
dev_err(dev, "unable to allocate CANdev\n"); |
| 1911 |
ret = -ENOMEM; |
| 1912 |
goto out_return; |
| 1913 |
} |
| 1914 |
|
| 1915 |
platform_set_drvdata(pdev, ndev); |
| 1916 |
mod = netdev_priv(ndev); |
| 1917 |
mod->ndev = ndev; |
| 1918 |
mod->num = pdata->modno; |
| 1919 |
netif_napi_add_weight(ndev, &mod->napi, ican3_napi, ICAN3_RX_BUFFERS); |
| 1920 |
skb_queue_head_init(&mod->echoq); |
| 1921 |
spin_lock_init(&mod->lock); |
| 1922 |
init_completion(&mod->termination_comp); |
| 1923 |
init_completion(&mod->buserror_comp); |
| 1924 |
|
| 1925 |
/* setup device-specific sysfs attributes */ |
| 1926 |
ndev->sysfs_groups[0] = &ican3_sysfs_attr_group; |
| 1927 |
|
| 1928 |
/* the first unallocated page in the DPM is 9 */ |
| 1929 |
mod->free_page = DPM_FREE_START; |
| 1930 |
|
| 1931 |
ndev->netdev_ops = &ican3_netdev_ops; |
| 1932 |
ndev->ethtool_ops = &ican3_ethtool_ops; |
| 1933 |
ndev->flags |= IFF_ECHO; |
| 1934 |
SET_NETDEV_DEV(ndev, &pdev->dev); |
| 1935 |
|
| 1936 |
mod->can.clock.freq = ICAN3_CAN_CLOCK; |
| 1937 |
mod->can.bittiming_const = &ican3_bittiming_const; |
| 1938 |
mod->can.do_set_mode = ican3_set_mode; |
| 1939 |
mod->can.do_get_berr_counter = ican3_get_berr_counter; |
| 1940 |
mod->can.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES |
| 1941 |
| CAN_CTRLMODE_BERR_REPORTING |
| 1942 |
| CAN_CTRLMODE_ONE_SHOT; |
| 1943 |
|
| 1944 |
/* find our IRQ number */ |
| 1945 |
mod->irq = platform_get_irq(pdev, 0); |
| 1946 |
if (mod->irq < 0) { |
| 1947 |
ret = -ENODEV; |
| 1948 |
goto out_free_ndev; |
| 1949 |
} |
| 1950 |
|
| 1951 |
ndev->irq = mod->irq; |
| 1952 |
|
| 1953 |
/* get access to the MODULbus registers for this module */ |
| 1954 |
res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| 1955 |
if (!res) { |
| 1956 |
dev_err(dev, "MODULbus registers not found\n"); |
| 1957 |
ret = -ENODEV; |
| 1958 |
goto out_free_ndev; |
| 1959 |
} |
| 1960 |
|
| 1961 |
mod->dpm = ioremap(res->start, resource_size(res)); |
| 1962 |
if (!mod->dpm) { |
| 1963 |
dev_err(dev, "MODULbus registers not ioremap\n"); |
| 1964 |
ret = -ENOMEM; |
| 1965 |
goto out_free_ndev; |
| 1966 |
} |
| 1967 |
|
| 1968 |
mod->dpmctrl = mod->dpm + DPM_PAGE_SIZE; |
| 1969 |
|
| 1970 |
/* get access to the control registers for this module */ |
| 1971 |
res = platform_get_resource(pdev, IORESOURCE_MEM, 1); |
| 1972 |
if (!res) { |
| 1973 |
dev_err(dev, "CONTROL registers not found\n"); |
| 1974 |
ret = -ENODEV; |
| 1975 |
goto out_iounmap_dpm; |
| 1976 |
} |
| 1977 |
|
| 1978 |
mod->ctrl = ioremap(res->start, resource_size(res)); |
| 1979 |
if (!mod->ctrl) { |
| 1980 |
dev_err(dev, "CONTROL registers not ioremap\n"); |
| 1981 |
ret = -ENOMEM; |
| 1982 |
goto out_iounmap_dpm; |
| 1983 |
} |
| 1984 |
|
| 1985 |
/* disable our IRQ, then hookup the IRQ handler */ |
| 1986 |
iowrite8(1 << mod->num, &mod->ctrl->int_disable); |
| 1987 |
ret = request_irq(mod->irq, ican3_irq, IRQF_SHARED, DRV_NAME, mod); |
| 1988 |
if (ret) { |
| 1989 |
dev_err(dev, "unable to request IRQ\n"); |
| 1990 |
goto out_iounmap_ctrl; |
| 1991 |
} |
| 1992 |
|
| 1993 |
/* reset and initialize the CAN controller into fast mode */ |
| 1994 |
napi_enable(&mod->napi); |
| 1995 |
ret = ican3_startup_module(mod); |
| 1996 |
if (ret) { |
| 1997 |
dev_err(dev, "%s: unable to start CANdev\n", __func__); |
| 1998 |
goto out_free_irq; |
| 1999 |
} |
| 2000 |
|
| 2001 |
/* register with the Linux CAN layer */ |
| 2002 |
ret = register_candev(ndev); |
| 2003 |
if (ret) { |
| 2004 |
dev_err(dev, "%s: unable to register CANdev\n", __func__); |
| 2005 |
goto out_free_irq; |
| 2006 |
} |
| 2007 |
|
| 2008 |
netdev_info(mod->ndev, "module %d: registered CAN device\n", pdata->modno); |
| 2009 |
return 0; |
| 2010 |
|
| 2011 |
out_free_irq: |
| 2012 |
napi_disable(&mod->napi); |
| 2013 |
iowrite8(1 << mod->num, &mod->ctrl->int_disable); |
| 2014 |
free_irq(mod->irq, mod); |
| 2015 |
out_iounmap_ctrl: |
| 2016 |
iounmap(mod->ctrl); |
| 2017 |
out_iounmap_dpm: |
| 2018 |
iounmap(mod->dpm); |
| 2019 |
out_free_ndev: |
| 2020 |
free_candev(ndev); |
| 2021 |
out_return: |
| 2022 |
return ret; |
| 2023 |
} |
| 2024 |
|
| 2025 |
static void ican3_remove(struct platform_device *pdev) |
| 2026 |
{ |
| 2027 |
struct net_device *ndev = platform_get_drvdata(pdev); |
| 2028 |
struct ican3_dev *mod = netdev_priv(ndev); |
| 2029 |
|
| 2030 |
/* unregister the netdevice, stop interrupts */ |
| 2031 |
unregister_netdev(ndev); |
| 2032 |
napi_disable(&mod->napi); |
| 2033 |
iowrite8(1 << mod->num, &mod->ctrl->int_disable); |
| 2034 |
free_irq(mod->irq, mod); |
| 2035 |
|
| 2036 |
/* put the module into reset */ |
| 2037 |
ican3_shutdown_module(mod); |
| 2038 |
|
| 2039 |
/* unmap all registers */ |
| 2040 |
iounmap(mod->ctrl); |
| 2041 |
iounmap(mod->dpm); |
| 2042 |
|
| 2043 |
free_candev(ndev); |
| 2044 |
} |
| 2045 |
|
| 2046 |
static struct platform_driver ican3_driver = { |
| 2047 |
.driver = { |
| 2048 |
.name = DRV_NAME, |
| 2049 |
}, |
| 2050 |
.probe = ican3_probe, |
| 2051 |
.remove = ican3_remove, |
| 2052 |
}; |
| 2053 |
|
| 2054 |
module_platform_driver(ican3_driver); |
| 2055 |
|
| 2056 |
MODULE_AUTHOR("Ira W. Snyder <[email protected]>"); |
| 2057 |
MODULE_DESCRIPTION("Janz MODULbus VMOD-ICAN3 Driver"); |
| 2058 |
MODULE_LICENSE("GPL"); |
| 2059 |
MODULE_ALIAS("platform:janz-ican3"); |