| 1 |
/* SPDX-License-Identifier: GPL-2.0 */ |
| 2 |
#ifndef __ASM_SH_SMC37C93X_H |
| 3 |
#define __ASM_SH_SMC37C93X_H |
| 4 |
|
| 5 |
/* |
| 6 |
* linux/include/asm-sh/smc37c93x.h |
| 7 |
* |
| 8 |
* Copyright (C) 2000 Kazumoto Kojima |
| 9 |
* |
| 10 |
* SMSC 37C93x Super IO Chip support |
| 11 |
*/ |
| 12 |
|
| 13 |
/* Default base I/O address */ |
| 14 |
#define FDC_PRIMARY_BASE 0x3f0 |
| 15 |
#define IDE1_PRIMARY_BASE 0x1f0 |
| 16 |
#define IDE1_SECONDARY_BASE 0x170 |
| 17 |
#define PARPORT_PRIMARY_BASE 0x378 |
| 18 |
#define COM1_PRIMARY_BASE 0x2f8 |
| 19 |
#define COM2_PRIMARY_BASE 0x3f8 |
| 20 |
#define RTC_PRIMARY_BASE 0x070 |
| 21 |
#define KBC_PRIMARY_BASE 0x060 |
| 22 |
#define AUXIO_PRIMARY_BASE 0x000 /* XXX */ |
| 23 |
|
| 24 |
/* Logical device number */ |
| 25 |
#define LDN_FDC 0 |
| 26 |
#define LDN_IDE1 1 |
| 27 |
#define LDN_IDE2 2 |
| 28 |
#define LDN_PARPORT 3 |
| 29 |
#define LDN_COM1 4 |
| 30 |
#define LDN_COM2 5 |
| 31 |
#define LDN_RTC 6 |
| 32 |
#define LDN_KBC 7 |
| 33 |
#define LDN_AUXIO 8 |
| 34 |
|
| 35 |
/* Configuration port and key */ |
| 36 |
#define CONFIG_PORT 0x3f0 |
| 37 |
#define INDEX_PORT CONFIG_PORT |
| 38 |
#define DATA_PORT 0x3f1 |
| 39 |
#define CONFIG_ENTER 0x55 |
| 40 |
#define CONFIG_EXIT 0xaa |
| 41 |
|
| 42 |
/* Configuration index */ |
| 43 |
#define CURRENT_LDN_INDEX 0x07 |
| 44 |
#define POWER_CONTROL_INDEX 0x22 |
| 45 |
#define ACTIVATE_INDEX 0x30 |
| 46 |
#define IO_BASE_HI_INDEX 0x60 |
| 47 |
#define IO_BASE_LO_INDEX 0x61 |
| 48 |
#define IRQ_SELECT_INDEX 0x70 |
| 49 |
#define DMA_SELECT_INDEX 0x74 |
| 50 |
|
| 51 |
#define GPIO46_INDEX 0xc6 |
| 52 |
#define GPIO47_INDEX 0xc7 |
| 53 |
|
| 54 |
/* UART stuff. Only for debugging. */ |
| 55 |
/* UART Register */ |
| 56 |
|
| 57 |
#define UART_RBR 0x0 /* Receiver Buffer Register (Read Only) */ |
| 58 |
#define UART_THR 0x0 /* Transmitter Holding Register (Write Only) */ |
| 59 |
#define UART_IER 0x2 /* Interrupt Enable Register */ |
| 60 |
#define UART_IIR 0x4 /* Interrupt Ident Register (Read Only) */ |
| 61 |
#define UART_FCR 0x4 /* FIFO Control Register (Write Only) */ |
| 62 |
#define UART_LCR 0x6 /* Line Control Register */ |
| 63 |
#define UART_MCR 0x8 /* MODEM Control Register */ |
| 64 |
#define UART_LSR 0xa /* Line Status Register */ |
| 65 |
#define UART_MSR 0xc /* MODEM Status Register */ |
| 66 |
#define UART_SCR 0xe /* Scratch Register */ |
| 67 |
#define UART_DLL 0x0 /* Divisor Latch (LS) */ |
| 68 |
#define UART_DLM 0x2 /* Divisor Latch (MS) */ |
| 69 |
|
| 70 |
#ifndef __ASSEMBLER__ |
| 71 |
typedef struct uart_reg { |
| 72 |
volatile __u16 rbr; |
| 73 |
volatile __u16 ier; |
| 74 |
volatile __u16 iir; |
| 75 |
volatile __u16 lcr; |
| 76 |
volatile __u16 mcr; |
| 77 |
volatile __u16 lsr; |
| 78 |
volatile __u16 msr; |
| 79 |
volatile __u16 scr; |
| 80 |
} uart_reg; |
| 81 |
#endif /* ! __ASSEMBLER__ */ |
| 82 |
|
| 83 |
/* Alias for Write Only Register */ |
| 84 |
|
| 85 |
#define thr rbr |
| 86 |
#define tcr iir |
| 87 |
|
| 88 |
/* Alias for Divisor Latch Register */ |
| 89 |
|
| 90 |
#define dll rbr |
| 91 |
#define dlm ier |
| 92 |
#define fcr iir |
| 93 |
|
| 94 |
/* Interrupt Enable Register */ |
| 95 |
|
| 96 |
#define IER_ERDAI 0x0100 /* Enable Received Data Available Interrupt */ |
| 97 |
#define IER_ETHREI 0x0200 /* Enable Transmitter Holding Register Empty Interrupt */ |
| 98 |
#define IER_ELSI 0x0400 /* Enable Receiver Line Status Interrupt */ |
| 99 |
#define IER_EMSI 0x0800 /* Enable MODEM Status Interrupt */ |
| 100 |
|
| 101 |
/* Interrupt Ident Register */ |
| 102 |
|
| 103 |
#define IIR_IP 0x0100 /* "0" if Interrupt Pending */ |
| 104 |
#define IIR_IIB0 0x0200 /* Interrupt ID Bit 0 */ |
| 105 |
#define IIR_IIB1 0x0400 /* Interrupt ID Bit 1 */ |
| 106 |
#define IIR_IIB2 0x0800 /* Interrupt ID Bit 2 */ |
| 107 |
#define IIR_FIFO 0xc000 /* FIFOs enabled */ |
| 108 |
|
| 109 |
/* FIFO Control Register */ |
| 110 |
|
| 111 |
#define FCR_FEN 0x0100 /* FIFO enable */ |
| 112 |
#define FCR_RFRES 0x0200 /* Receiver FIFO reset */ |
| 113 |
#define FCR_TFRES 0x0400 /* Transmitter FIFO reset */ |
| 114 |
#define FCR_DMA 0x0800 /* DMA mode select */ |
| 115 |
#define FCR_RTL 0x4000 /* Receiver trigger (LSB) */ |
| 116 |
#define FCR_RTM 0x8000 /* Receiver trigger (MSB) */ |
| 117 |
|
| 118 |
/* Line Control Register */ |
| 119 |
|
| 120 |
#define LCR_WLS0 0x0100 /* Word Length Select Bit 0 */ |
| 121 |
#define LCR_WLS1 0x0200 /* Word Length Select Bit 1 */ |
| 122 |
#define LCR_STB 0x0400 /* Number of Stop Bits */ |
| 123 |
#define LCR_PEN 0x0800 /* Parity Enable */ |
| 124 |
#define LCR_EPS 0x1000 /* Even Parity Select */ |
| 125 |
#define LCR_SP 0x2000 /* Stick Parity */ |
| 126 |
#define LCR_SB 0x4000 /* Set Break */ |
| 127 |
#define LCR_DLAB 0x8000 /* Divisor Latch Access Bit */ |
| 128 |
|
| 129 |
/* MODEM Control Register */ |
| 130 |
|
| 131 |
#define MCR_DTR 0x0100 /* Data Terminal Ready */ |
| 132 |
#define MCR_RTS 0x0200 /* Request to Send */ |
| 133 |
#define MCR_OUT1 0x0400 /* Out 1 */ |
| 134 |
#define MCR_IRQEN 0x0800 /* IRQ Enable */ |
| 135 |
#define MCR_LOOP 0x1000 /* Loop */ |
| 136 |
|
| 137 |
/* Line Status Register */ |
| 138 |
|
| 139 |
#define LSR_DR 0x0100 /* Data Ready */ |
| 140 |
#define LSR_OE 0x0200 /* Overrun Error */ |
| 141 |
#define LSR_PE 0x0400 /* Parity Error */ |
| 142 |
#define LSR_FE 0x0800 /* Framing Error */ |
| 143 |
#define LSR_BI 0x1000 /* Break Interrupt */ |
| 144 |
#define LSR_THRE 0x2000 /* Transmitter Holding Register Empty */ |
| 145 |
#define LSR_TEMT 0x4000 /* Transmitter Empty */ |
| 146 |
#define LSR_FIFOE 0x8000 /* Receiver FIFO error */ |
| 147 |
|
| 148 |
/* MODEM Status Register */ |
| 149 |
|
| 150 |
#define MSR_DCTS 0x0100 /* Delta Clear to Send */ |
| 151 |
#define MSR_DDSR 0x0200 /* Delta Data Set Ready */ |
| 152 |
#define MSR_TERI 0x0400 /* Trailing Edge Ring Indicator */ |
| 153 |
#define MSR_DDCD 0x0800 /* Delta Data Carrier Detect */ |
| 154 |
#define MSR_CTS 0x1000 /* Clear to Send */ |
| 155 |
#define MSR_DSR 0x2000 /* Data Set Ready */ |
| 156 |
#define MSR_RI 0x4000 /* Ring Indicator */ |
| 157 |
#define MSR_DCD 0x8000 /* Data Carrier Detect */ |
| 158 |
|
| 159 |
/* Baud Rate Divisor */ |
| 160 |
|
| 161 |
#define UART_CLK (1843200) /* 1.8432 MHz */ |
| 162 |
#define UART_BAUD(x) (UART_CLK / (16 * (x))) |
| 163 |
|
| 164 |
/* RTC register definition */ |
| 165 |
#define RTC_SECONDS 0 |
| 166 |
#define RTC_SECONDS_ALARM 1 |
| 167 |
#define RTC_MINUTES 2 |
| 168 |
#define RTC_MINUTES_ALARM 3 |
| 169 |
#define RTC_HOURS 4 |
| 170 |
#define RTC_HOURS_ALARM 5 |
| 171 |
#define RTC_DAY_OF_WEEK 6 |
| 172 |
#define RTC_DAY_OF_MONTH 7 |
| 173 |
#define RTC_MONTH 8 |
| 174 |
#define RTC_YEAR 9 |
| 175 |
#define RTC_FREQ_SELECT 10 |
| 176 |
# define RTC_UIP 0x80 |
| 177 |
# define RTC_DIV_CTL 0x70 |
| 178 |
/* This RTC can work under 32.768KHz clock only. */ |
| 179 |
# define RTC_OSC_ENABLE 0x20 |
| 180 |
# define RTC_OSC_DISABLE 0x00 |
| 181 |
#define RTC_CONTROL 11 |
| 182 |
# define RTC_SET 0x80 |
| 183 |
# define RTC_PIE 0x40 |
| 184 |
# define RTC_AIE 0x20 |
| 185 |
# define RTC_UIE 0x10 |
| 186 |
# define RTC_SQWE 0x08 |
| 187 |
# define RTC_DM_BINARY 0x04 |
| 188 |
# define RTC_24H 0x02 |
| 189 |
# define RTC_DST_EN 0x01 |
| 190 |
|
| 191 |
#endif /* __ASM_SH_SMC37C93X_H */ |