| 1 |
/* SPDX-License-Identifier: GPL-2.0 */ |
| 2 |
/* |
| 3 |
* sh7760fb.h -- platform data for SH7760/SH7763 LCDC framebuffer driver. |
| 4 |
* |
| 5 |
* (c) 2006-2008 MSC Vertriebsges.m.b.H., |
| 6 |
* Manuel Lauss <[email protected]> |
| 7 |
* (c) 2008 Nobuhiro Iwamatsu <[email protected]> |
| 8 |
*/ |
| 9 |
|
| 10 |
#ifndef _ASM_SH_SH7760FB_H |
| 11 |
#define _ASM_SH_SH7760FB_H |
| 12 |
|
| 13 |
/* |
| 14 |
* some bits of the colormap registers should be written as zero. |
| 15 |
* create a mask for that. |
| 16 |
*/ |
| 17 |
#define SH7760FB_PALETTE_MASK 0x00f8fcf8 |
| 18 |
|
| 19 |
/* The LCDC dma engine always sets bits 27-26 to 1: this is Area3 */ |
| 20 |
#define SH7760FB_DMA_MASK 0x0C000000 |
| 21 |
|
| 22 |
/* palette */ |
| 23 |
#define LDPR(x) (((x) << 2)) |
| 24 |
|
| 25 |
/* framebuffer registers and bits */ |
| 26 |
#define LDICKR 0x400 |
| 27 |
#define LDMTR 0x402 |
| 28 |
/* see sh7760fb.h for LDMTR bits */ |
| 29 |
#define LDDFR 0x404 |
| 30 |
#define LDDFR_PABD (1 << 8) |
| 31 |
#define LDDFR_COLOR_MASK 0x7F |
| 32 |
#define LDSMR 0x406 |
| 33 |
#define LDSMR_ROT (1 << 13) |
| 34 |
#define LDSARU 0x408 |
| 35 |
#define LDSARL 0x40c |
| 36 |
#define LDLAOR 0x410 |
| 37 |
#define LDPALCR 0x412 |
| 38 |
#define LDPALCR_PALS (1 << 4) |
| 39 |
#define LDPALCR_PALEN (1 << 0) |
| 40 |
#define LDHCNR 0x414 |
| 41 |
#define LDHSYNR 0x416 |
| 42 |
#define LDVDLNR 0x418 |
| 43 |
#define LDVTLNR 0x41a |
| 44 |
#define LDVSYNR 0x41c |
| 45 |
#define LDACLNR 0x41e |
| 46 |
#define LDINTR 0x420 |
| 47 |
#define LDPMMR 0x424 |
| 48 |
#define LDPSPR 0x426 |
| 49 |
#define LDCNTR 0x428 |
| 50 |
#define LDCNTR_DON (1 << 0) |
| 51 |
#define LDCNTR_DON2 (1 << 4) |
| 52 |
|
| 53 |
#ifdef CONFIG_CPU_SUBTYPE_SH7763 |
| 54 |
# define LDLIRNR 0x440 |
| 55 |
/* LDINTR bit */ |
| 56 |
# define LDINTR_MINTEN (1 << 15) |
| 57 |
# define LDINTR_FINTEN (1 << 14) |
| 58 |
# define LDINTR_VSINTEN (1 << 13) |
| 59 |
# define LDINTR_VEINTEN (1 << 12) |
| 60 |
# define LDINTR_MINTS (1 << 11) |
| 61 |
# define LDINTR_FINTS (1 << 10) |
| 62 |
# define LDINTR_VSINTS (1 << 9) |
| 63 |
# define LDINTR_VEINTS (1 << 8) |
| 64 |
# define VINT_START (LDINTR_VSINTEN) |
| 65 |
# define VINT_CHECK (LDINTR_VSINTS) |
| 66 |
#else |
| 67 |
/* LDINTR bit */ |
| 68 |
# define LDINTR_VINTSEL (1 << 12) |
| 69 |
# define LDINTR_VINTE (1 << 8) |
| 70 |
# define LDINTR_VINTS (1 << 0) |
| 71 |
# define VINT_START (LDINTR_VINTSEL) |
| 72 |
# define VINT_CHECK (LDINTR_VINTS) |
| 73 |
#endif |
| 74 |
|
| 75 |
/* HSYNC polarity inversion */ |
| 76 |
#define LDMTR_FLMPOL (1 << 15) |
| 77 |
|
| 78 |
/* VSYNC polarity inversion */ |
| 79 |
#define LDMTR_CL1POL (1 << 14) |
| 80 |
|
| 81 |
/* DISPLAY-ENABLE polarity inversion */ |
| 82 |
#define LDMTR_DISPEN_LOWACT (1 << 13) |
| 83 |
|
| 84 |
/* DISPLAY DATA BUS polarity inversion */ |
| 85 |
#define LDMTR_DPOL_LOWACT (1 << 12) |
| 86 |
|
| 87 |
/* AC modulation signal enable */ |
| 88 |
#define LDMTR_MCNT (1 << 10) |
| 89 |
|
| 90 |
/* Disable output of HSYNC during VSYNC period */ |
| 91 |
#define LDMTR_CL1CNT (1 << 9) |
| 92 |
|
| 93 |
/* Disable output of VSYNC during VSYNC period */ |
| 94 |
#define LDMTR_CL2CNT (1 << 8) |
| 95 |
|
| 96 |
/* Display types supported by the LCDC */ |
| 97 |
#define LDMTR_STN_MONO_4 0x00 |
| 98 |
#define LDMTR_STN_MONO_8 0x01 |
| 99 |
#define LDMTR_STN_COLOR_4 0x08 |
| 100 |
#define LDMTR_STN_COLOR_8 0x09 |
| 101 |
#define LDMTR_STN_COLOR_12 0x0A |
| 102 |
#define LDMTR_STN_COLOR_16 0x0B |
| 103 |
#define LDMTR_DSTN_MONO_8 0x11 |
| 104 |
#define LDMTR_DSTN_MONO_16 0x13 |
| 105 |
#define LDMTR_DSTN_COLOR_8 0x19 |
| 106 |
#define LDMTR_DSTN_COLOR_12 0x1A |
| 107 |
#define LDMTR_DSTN_COLOR_16 0x1B |
| 108 |
#define LDMTR_TFT_COLOR_16 0x2B |
| 109 |
|
| 110 |
/* framebuffer color layout */ |
| 111 |
#define LDDFR_1BPP_MONO 0x00 |
| 112 |
#define LDDFR_2BPP_MONO 0x01 |
| 113 |
#define LDDFR_4BPP_MONO 0x02 |
| 114 |
#define LDDFR_6BPP_MONO 0x04 |
| 115 |
#define LDDFR_4BPP 0x0A |
| 116 |
#define LDDFR_8BPP 0x0C |
| 117 |
#define LDDFR_16BPP_RGB555 0x1D |
| 118 |
#define LDDFR_16BPP_RGB565 0x2D |
| 119 |
|
| 120 |
/* LCDC Pixclock sources */ |
| 121 |
#define LCDC_CLKSRC_BUSCLOCK 0 |
| 122 |
#define LCDC_CLKSRC_PERIPHERAL 1 |
| 123 |
#define LCDC_CLKSRC_EXTERNAL 2 |
| 124 |
|
| 125 |
#define LDICKR_CLKSRC(x) \ |
| 126 |
(((x) & 3) << 12) |
| 127 |
|
| 128 |
/* LCDC pixclock input divider. Set to 1 at a minimum! */ |
| 129 |
#define LDICKR_CLKDIV(x) \ |
| 130 |
((x) & 0x1f) |
| 131 |
|
| 132 |
struct sh7760fb_platdata { |
| 133 |
|
| 134 |
/* Set this member to a valid fb_videmode for the display you |
| 135 |
* wish to use. The following members must be initialized: |
| 136 |
* xres, yres, hsync_len, vsync_len, sync, |
| 137 |
* {left,right,upper,lower}_margin. |
| 138 |
* The driver uses the above members to calculate register values |
| 139 |
* and memory requirements. Other members are ignored but may |
| 140 |
* be used by other framebuffer layer components. |
| 141 |
*/ |
| 142 |
struct fb_videomode *def_mode; |
| 143 |
|
| 144 |
/* LDMTR includes display type and signal polarity. The |
| 145 |
* HSYNC/VSYNC polarities are derived from the fb_var_screeninfo |
| 146 |
* data above; however the polarities of the following signals |
| 147 |
* must be encoded in the ldmtr member: |
| 148 |
* Display Enable signal (default high-active) DISPEN_LOWACT |
| 149 |
* Display Data signals (default high-active) DPOL_LOWACT |
| 150 |
* AC Modulation signal (default off) MCNT |
| 151 |
* Hsync-During-Vsync suppression (default off) CL1CNT |
| 152 |
* Vsync-during-vsync suppression (default off) CL2CNT |
| 153 |
* NOTE: also set a display type! |
| 154 |
* (one of LDMTR_{STN,DSTN,TFT}_{MONO,COLOR}_{4,8,12,16}) |
| 155 |
*/ |
| 156 |
u16 ldmtr; |
| 157 |
|
| 158 |
/* LDDFR controls framebuffer image format (depth, organization) |
| 159 |
* Use ONE of the LDDFR_?BPP_* macros! |
| 160 |
*/ |
| 161 |
u16 lddfr; |
| 162 |
|
| 163 |
/* LDPMMR and LDPSPR control the timing of the power signals |
| 164 |
* for the display. Please read the SH7760 Hardware Manual, |
| 165 |
* Chapters 30.3.17, 30.3.18 and 30.4.6! |
| 166 |
*/ |
| 167 |
u16 ldpmmr; |
| 168 |
u16 ldpspr; |
| 169 |
|
| 170 |
/* LDACLNR contains the line numbers after which the AC modulation |
| 171 |
* signal is to toggle. Set to ZERO for TFTs or displays which |
| 172 |
* do not need it. (Chapter 30.3.15 in SH7760 Hardware Manual). |
| 173 |
*/ |
| 174 |
u16 ldaclnr; |
| 175 |
|
| 176 |
/* LDICKR contains information on pixelclock source and config. |
| 177 |
* Please use the LDICKR_CLKSRC() and LDICKR_CLKDIV() macros. |
| 178 |
* minimal value for CLKDIV() must be 1!. |
| 179 |
*/ |
| 180 |
u16 ldickr; |
| 181 |
|
| 182 |
/* set this member to 1 if you wish to use the LCDC's hardware |
| 183 |
* rotation function. This is limited to displays <= 320x200 |
| 184 |
* pixels resolution! |
| 185 |
*/ |
| 186 |
int rotate; /* set to 1 to rotate 90 CCW */ |
| 187 |
|
| 188 |
/* set this to 1 to suppress vsync irq use. */ |
| 189 |
int novsync; |
| 190 |
|
| 191 |
/* blanking hook for platform. Set this if your platform can do |
| 192 |
* more than the LCDC in terms of blanking (e.g. disable clock |
| 193 |
* generator / backlight power supply / etc. |
| 194 |
*/ |
| 195 |
void (*blank) (int); |
| 196 |
}; |
| 197 |
|
| 198 |
#endif /* _ASM_SH_SH7760FB_H */ |