| 1 |
/* |
| 2 |
* This file is subject to the terms and conditions of the GNU General Public |
| 3 |
* License. See the file "COPYING" in the main directory of this archive |
| 4 |
* for more details. |
| 5 |
* |
| 6 |
* hpc3.h: Definitions for SGI HPC3 controller |
| 7 |
* |
| 8 |
* Copyright (C) 1996 David S. Miller |
| 9 |
* Copyright (C) 1998 Ralf Baechle |
| 10 |
*/ |
| 11 |
|
| 12 |
#ifndef _SGI_HPC3_H |
| 13 |
#define _SGI_HPC3_H |
| 14 |
|
| 15 |
#include <linux/types.h> |
| 16 |
#include <asm/page.h> |
| 17 |
|
| 18 |
/* An HPC DMA descriptor. */ |
| 19 |
struct hpc_dma_desc { |
| 20 |
u32 pbuf; /* physical address of data buffer */ |
| 21 |
u32 cntinfo; /* counter and info bits */ |
| 22 |
#define HPCDMA_EOX 0x80000000 /* last desc in chain for tx */ |
| 23 |
#define HPCDMA_EOR 0x80000000 /* last desc in chain for rx */ |
| 24 |
#define HPCDMA_EOXP 0x40000000 /* end of packet for tx */ |
| 25 |
#define HPCDMA_EORP 0x40000000 /* end of packet for rx */ |
| 26 |
#define HPCDMA_XIE 0x20000000 /* irq generated when at end of this desc */ |
| 27 |
#define HPCDMA_XIU 0x01000000 /* Tx buffer in use by CPU. */ |
| 28 |
#define HPCDMA_EIPC 0x00ff0000 /* SEEQ ethernet special xternal bytecount */ |
| 29 |
#define HPCDMA_ETXD 0x00008000 /* set to one by HPC when packet tx'd */ |
| 30 |
#define HPCDMA_OWN 0x00004000 /* Denotes ring buffer ownership on rx */ |
| 31 |
#define HPCDMA_BCNT 0x00003fff /* size in bytes of this dma buffer */ |
| 32 |
|
| 33 |
u32 pnext; /* paddr of next hpc_dma_desc if any */ |
| 34 |
}; |
| 35 |
|
| 36 |
/* The set of regs for each HPC3 PBUS DMA channel. */ |
| 37 |
struct hpc3_pbus_dmacregs { |
| 38 |
volatile u32 pbdma_bptr; /* pbus dma channel buffer ptr */ |
| 39 |
volatile u32 pbdma_dptr; /* pbus dma channel desc ptr */ |
| 40 |
u32 _unused0[0x1000/4 - 2]; /* padding */ |
| 41 |
volatile u32 pbdma_ctrl; /* pbus dma channel control register has |
| 42 |
* completely different meaning for read |
| 43 |
* compared with write */ |
| 44 |
/* read */ |
| 45 |
#define HPC3_PDMACTRL_INT 0x00000001 /* interrupt (cleared after read) */ |
| 46 |
#define HPC3_PDMACTRL_ISACT 0x00000002 /* channel active */ |
| 47 |
/* write */ |
| 48 |
#define HPC3_PDMACTRL_SEL 0x00000002 /* little endian transfer */ |
| 49 |
#define HPC3_PDMACTRL_RCV 0x00000004 /* direction is receive */ |
| 50 |
#define HPC3_PDMACTRL_FLSH 0x00000008 /* enable flush for receive DMA */ |
| 51 |
#define HPC3_PDMACTRL_ACT 0x00000010 /* start dma transfer */ |
| 52 |
#define HPC3_PDMACTRL_LD 0x00000020 /* load enable for ACT */ |
| 53 |
#define HPC3_PDMACTRL_RT 0x00000040 /* Use realtime GIO bus servicing */ |
| 54 |
#define HPC3_PDMACTRL_HW 0x0000ff00 /* DMA High-water mark */ |
| 55 |
#define HPC3_PDMACTRL_FB 0x003f0000 /* Ptr to beginning of fifo */ |
| 56 |
#define HPC3_PDMACTRL_FE 0x3f000000 /* Ptr to end of fifo */ |
| 57 |
|
| 58 |
u32 _unused1[0x1000/4 - 1]; /* padding */ |
| 59 |
}; |
| 60 |
|
| 61 |
/* The HPC3 SCSI registers, this does not include external ones. */ |
| 62 |
struct hpc3_scsiregs { |
| 63 |
volatile u32 cbptr; /* current dma buffer ptr, diagnostic use only */ |
| 64 |
volatile u32 ndptr; /* next dma descriptor ptr */ |
| 65 |
u32 _unused0[0x1000/4 - 2]; /* padding */ |
| 66 |
volatile u32 bcd; /* byte count info */ |
| 67 |
#define HPC3_SBCD_BCNTMSK 0x00003fff /* bytes to transfer from/to memory */ |
| 68 |
#define HPC3_SBCD_XIE 0x00004000 /* Send IRQ when done with cur buf */ |
| 69 |
#define HPC3_SBCD_EOX 0x00008000 /* Indicates this is last buf in chain */ |
| 70 |
|
| 71 |
volatile u32 ctrl; /* control register */ |
| 72 |
#define HPC3_SCTRL_IRQ 0x01 /* IRQ asserted, either dma done or parity */ |
| 73 |
#define HPC3_SCTRL_ENDIAN 0x02 /* DMA endian mode, 0=big 1=little */ |
| 74 |
#define HPC3_SCTRL_DIR 0x04 /* DMA direction, 1=dev2mem 0=mem2dev */ |
| 75 |
#define HPC3_SCTRL_FLUSH 0x08 /* Tells HPC3 to flush scsi fifos */ |
| 76 |
#define HPC3_SCTRL_ACTIVE 0x10 /* SCSI DMA channel is active */ |
| 77 |
#define HPC3_SCTRL_AMASK 0x20 /* DMA active inhibits PIO */ |
| 78 |
#define HPC3_SCTRL_CRESET 0x40 /* Resets dma channel and external controller */ |
| 79 |
#define HPC3_SCTRL_PERR 0x80 /* Bad parity on HPC3 iface to scsi controller */ |
| 80 |
|
| 81 |
volatile u32 gfptr; /* current GIO fifo ptr */ |
| 82 |
volatile u32 dfptr; /* current device fifo ptr */ |
| 83 |
volatile u32 dconfig; /* DMA configuration register */ |
| 84 |
#define HPC3_SDCFG_HCLK 0x00001 /* Enable DMA half clock mode */ |
| 85 |
#define HPC3_SDCFG_D1 0x00006 /* Cycles to spend in D1 state */ |
| 86 |
#define HPC3_SDCFG_D2 0x00038 /* Cycles to spend in D2 state */ |
| 87 |
#define HPC3_SDCFG_D3 0x001c0 /* Cycles to spend in D3 state */ |
| 88 |
#define HPC3_SDCFG_HWAT 0x00e00 /* DMA high water mark */ |
| 89 |
#define HPC3_SDCFG_HW 0x01000 /* Enable 16-bit halfword DMA accesses to scsi */ |
| 90 |
#define HPC3_SDCFG_SWAP 0x02000 /* Byte swap all DMA accesses */ |
| 91 |
#define HPC3_SDCFG_EPAR 0x04000 /* Enable parity checking for DMA */ |
| 92 |
#define HPC3_SDCFG_POLL 0x08000 /* hd_dreq polarity control */ |
| 93 |
#define HPC3_SDCFG_ERLY 0x30000 /* hd_dreq behavior control bits */ |
| 94 |
|
| 95 |
volatile u32 pconfig; /* PIO configuration register */ |
| 96 |
#define HPC3_SPCFG_P3 0x0003 /* Cycles to spend in P3 state */ |
| 97 |
#define HPC3_SPCFG_P2W 0x001c /* Cycles to spend in P2 state for writes */ |
| 98 |
#define HPC3_SPCFG_P2R 0x01e0 /* Cycles to spend in P2 state for reads */ |
| 99 |
#define HPC3_SPCFG_P1 0x0e00 /* Cycles to spend in P1 state */ |
| 100 |
#define HPC3_SPCFG_HW 0x1000 /* Enable 16-bit halfword PIO accesses to scsi */ |
| 101 |
#define HPC3_SPCFG_SWAP 0x2000 /* Byte swap all PIO accesses */ |
| 102 |
#define HPC3_SPCFG_EPAR 0x4000 /* Enable parity checking for PIO */ |
| 103 |
#define HPC3_SPCFG_FUJI 0x8000 /* Fujitsu scsi controller mode for faster dma/pio */ |
| 104 |
|
| 105 |
u32 _unused1[0x1000/4 - 6]; /* padding */ |
| 106 |
}; |
| 107 |
|
| 108 |
/* SEEQ ethernet HPC3 registers, only one seeq per HPC3. */ |
| 109 |
struct hpc3_ethregs { |
| 110 |
/* Receiver registers. */ |
| 111 |
volatile u32 rx_cbptr; /* current dma buffer ptr, diagnostic use only */ |
| 112 |
volatile u32 rx_ndptr; /* next dma descriptor ptr */ |
| 113 |
u32 _unused0[0x1000/4 - 2]; /* padding */ |
| 114 |
volatile u32 rx_bcd; /* byte count info */ |
| 115 |
#define HPC3_ERXBCD_BCNTMSK 0x00003fff /* bytes to be sent to memory */ |
| 116 |
#define HPC3_ERXBCD_XIE 0x20000000 /* HPC3 interrupts cpu at end of this buf */ |
| 117 |
#define HPC3_ERXBCD_EOX 0x80000000 /* flags this as end of descriptor chain */ |
| 118 |
|
| 119 |
volatile u32 rx_ctrl; /* control register */ |
| 120 |
#define HPC3_ERXCTRL_STAT50 0x0000003f /* Receive status reg bits of Seeq8003 */ |
| 121 |
#define HPC3_ERXCTRL_STAT6 0x00000040 /* Rdonly irq status */ |
| 122 |
#define HPC3_ERXCTRL_STAT7 0x00000080 /* Rdonlt old/new status bit from Seeq */ |
| 123 |
#define HPC3_ERXCTRL_ENDIAN 0x00000100 /* Endian for dma channel, little=1 big=0 */ |
| 124 |
#define HPC3_ERXCTRL_ACTIVE 0x00000200 /* Tells if DMA transfer is in progress */ |
| 125 |
#define HPC3_ERXCTRL_AMASK 0x00000400 /* Tells if ACTIVE inhibits PIO's to hpc3 */ |
| 126 |
#define HPC3_ERXCTRL_RBO 0x00000800 /* Receive buffer overflow if set to 1 */ |
| 127 |
|
| 128 |
volatile u32 rx_gfptr; /* current GIO fifo ptr */ |
| 129 |
volatile u32 rx_dfptr; /* current device fifo ptr */ |
| 130 |
u32 _unused1; /* padding */ |
| 131 |
volatile u32 reset; /* reset register */ |
| 132 |
#define HPC3_ERST_CRESET 0x1 /* Reset dma channel and external controller */ |
| 133 |
#define HPC3_ERST_CLRIRQ 0x2 /* Clear channel interrupt */ |
| 134 |
#define HPC3_ERST_LBACK 0x4 /* Enable diagnostic loopback mode of Seeq8003 */ |
| 135 |
|
| 136 |
volatile u32 dconfig; /* DMA configuration register */ |
| 137 |
#define HPC3_EDCFG_D1 0x0000f /* Cycles to spend in D1 state for PIO */ |
| 138 |
#define HPC3_EDCFG_D2 0x000f0 /* Cycles to spend in D2 state for PIO */ |
| 139 |
#define HPC3_EDCFG_D3 0x00f00 /* Cycles to spend in D3 state for PIO */ |
| 140 |
#define HPC3_EDCFG_WCTRL 0x01000 /* Enable writes of desc into ex ctrl port */ |
| 141 |
#define HPC3_EDCFG_FRXDC 0x02000 /* Clear eop stat bits upon rxdc, hw seeq fix */ |
| 142 |
#define HPC3_EDCFG_FEOP 0x04000 /* Bad packet marker timeout enable */ |
| 143 |
#define HPC3_EDCFG_FIRQ 0x08000 /* Another bad packet timeout enable */ |
| 144 |
#define HPC3_EDCFG_PTO 0x30000 /* Programmed timeout value for above two */ |
| 145 |
|
| 146 |
volatile u32 pconfig; /* PIO configuration register */ |
| 147 |
#define HPC3_EPCFG_P1 0x000f /* Cycles to spend in P1 state for PIO */ |
| 148 |
#define HPC3_EPCFG_P2 0x00f0 /* Cycles to spend in P2 state for PIO */ |
| 149 |
#define HPC3_EPCFG_P3 0x0f00 /* Cycles to spend in P3 state for PIO */ |
| 150 |
#define HPC3_EPCFG_TST 0x1000 /* Diagnostic ram test feature bit */ |
| 151 |
|
| 152 |
u32 _unused2[0x1000/4 - 8]; /* padding */ |
| 153 |
|
| 154 |
/* Transmitter registers. */ |
| 155 |
volatile u32 tx_cbptr; /* current dma buffer ptr, diagnostic use only */ |
| 156 |
volatile u32 tx_ndptr; /* next dma descriptor ptr */ |
| 157 |
u32 _unused3[0x1000/4 - 2]; /* padding */ |
| 158 |
volatile u32 tx_bcd; /* byte count info */ |
| 159 |
#define HPC3_ETXBCD_BCNTMSK 0x00003fff /* bytes to be read from memory */ |
| 160 |
#define HPC3_ETXBCD_ESAMP 0x10000000 /* if set, too late to add descriptor */ |
| 161 |
#define HPC3_ETXBCD_XIE 0x20000000 /* Interrupt cpu at end of cur desc */ |
| 162 |
#define HPC3_ETXBCD_EOP 0x40000000 /* Last byte of cur buf is end of packet */ |
| 163 |
#define HPC3_ETXBCD_EOX 0x80000000 /* This buf is the end of desc chain */ |
| 164 |
|
| 165 |
volatile u32 tx_ctrl; /* control register */ |
| 166 |
#define HPC3_ETXCTRL_STAT30 0x0000000f /* Rdonly copy of seeq tx stat reg */ |
| 167 |
#define HPC3_ETXCTRL_STAT4 0x00000010 /* Indicate late collision occurred */ |
| 168 |
#define HPC3_ETXCTRL_STAT75 0x000000e0 /* Rdonly irq status from seeq */ |
| 169 |
#define HPC3_ETXCTRL_ENDIAN 0x00000100 /* DMA channel endian mode, 1=little 0=big */ |
| 170 |
#define HPC3_ETXCTRL_ACTIVE 0x00000200 /* DMA tx channel is active */ |
| 171 |
#define HPC3_ETXCTRL_AMASK 0x00000400 /* Indicates ACTIVE inhibits PIO's */ |
| 172 |
|
| 173 |
volatile u32 tx_gfptr; /* current GIO fifo ptr */ |
| 174 |
volatile u32 tx_dfptr; /* current device fifo ptr */ |
| 175 |
u32 _unused4[0x1000/4 - 4]; /* padding */ |
| 176 |
}; |
| 177 |
|
| 178 |
struct hpc3_regs { |
| 179 |
/* First regs for the PBUS 8 dma channels. */ |
| 180 |
struct hpc3_pbus_dmacregs pbdma[8]; |
| 181 |
|
| 182 |
/* Now the HPC scsi registers, we get two scsi reg sets. */ |
| 183 |
struct hpc3_scsiregs scsi_chan0, scsi_chan1; |
| 184 |
|
| 185 |
/* The SEEQ hpc3 ethernet dma/control registers. */ |
| 186 |
struct hpc3_ethregs ethregs; |
| 187 |
|
| 188 |
/* Here are where the hpc3 fifo's can be directly accessed |
| 189 |
* via PIO accesses. Under normal operation we never stick |
| 190 |
* our grubby paws in here so it's just padding. */ |
| 191 |
u32 _unused0[0x18000/4]; |
| 192 |
|
| 193 |
/* HPC3 irq status regs. Due to a peculiar bug you need to |
| 194 |
* look at two different register addresses to get at all of |
| 195 |
* the status bits. The first reg can only reliably report |
| 196 |
* bits 4:0 of the status, and the second reg can only |
| 197 |
* reliably report bits 9:5 of the hpc3 irq status. I told |
| 198 |
* you it was a peculiar bug. ;-) |
| 199 |
*/ |
| 200 |
volatile u32 istat0; /* Irq status, only bits <4:0> reliable. */ |
| 201 |
#define HPC3_ISTAT_PBIMASK 0x0ff /* irq bits for pbus devs 0 --> 7 */ |
| 202 |
#define HPC3_ISTAT_SC0MASK 0x100 /* irq bit for scsi channel 0 */ |
| 203 |
#define HPC3_ISTAT_SC1MASK 0x200 /* irq bit for scsi channel 1 */ |
| 204 |
|
| 205 |
volatile u32 gio_misc; /* GIO misc control bits. */ |
| 206 |
#define HPC3_GIOMISC_ERTIME 0x1 /* Enable external timer real time. */ |
| 207 |
#define HPC3_GIOMISC_DENDIAN 0x2 /* dma descriptor endian, 1=lit 0=big */ |
| 208 |
|
| 209 |
u32 eeprom; /* EEPROM data reg. */ |
| 210 |
#define HPC3_EEPROM_EPROT 0x01 /* Protect register enable */ |
| 211 |
#define HPC3_EEPROM_CSEL 0x02 /* Chip select */ |
| 212 |
#define HPC3_EEPROM_ECLK 0x04 /* EEPROM clock */ |
| 213 |
#define HPC3_EEPROM_DATO 0x08 /* Data out */ |
| 214 |
#define HPC3_EEPROM_DATI 0x10 /* Data in */ |
| 215 |
|
| 216 |
volatile u32 istat1; /* Irq status, only bits <9:5> reliable. */ |
| 217 |
volatile u32 bestat; /* Bus error interrupt status reg. */ |
| 218 |
#define HPC3_BESTAT_BLMASK 0x000ff /* Bus lane where bad parity occurred */ |
| 219 |
#define HPC3_BESTAT_CTYPE 0x00100 /* Bus cycle type, 0=PIO 1=DMA */ |
| 220 |
#define HPC3_BESTAT_PIDSHIFT 9 |
| 221 |
#define HPC3_BESTAT_PIDMASK 0x3f700 /* DMA channel parity identifier */ |
| 222 |
|
| 223 |
u32 _unused1[0x14000/4 - 5]; /* padding */ |
| 224 |
|
| 225 |
/* Now direct PIO per-HPC3 peripheral access to external regs. */ |
| 226 |
volatile u32 scsi0_ext[256]; /* SCSI channel 0 external regs */ |
| 227 |
u32 _unused2[0x7c00/4]; |
| 228 |
volatile u32 scsi1_ext[256]; /* SCSI channel 1 external regs */ |
| 229 |
u32 _unused3[0x7c00/4]; |
| 230 |
volatile u32 eth_ext[320]; /* Ethernet external registers */ |
| 231 |
u32 _unused4[0x3b00/4]; |
| 232 |
|
| 233 |
/* Per-peripheral device external registers and DMA/PIO control. */ |
| 234 |
volatile u32 pbus_extregs[16][256]; |
| 235 |
volatile u32 pbus_dmacfg[8][128]; |
| 236 |
/* Cycles to spend in D3 for reads */ |
| 237 |
#define HPC3_DMACFG_D3R_MASK 0x00000001 |
| 238 |
#define HPC3_DMACFG_D3R_SHIFT 0 |
| 239 |
/* Cycles to spend in D4 for reads */ |
| 240 |
#define HPC3_DMACFG_D4R_MASK 0x0000001e |
| 241 |
#define HPC3_DMACFG_D4R_SHIFT 1 |
| 242 |
/* Cycles to spend in D5 for reads */ |
| 243 |
#define HPC3_DMACFG_D5R_MASK 0x000001e0 |
| 244 |
#define HPC3_DMACFG_D5R_SHIFT 5 |
| 245 |
/* Cycles to spend in D3 for writes */ |
| 246 |
#define HPC3_DMACFG_D3W_MASK 0x00000200 |
| 247 |
#define HPC3_DMACFG_D3W_SHIFT 9 |
| 248 |
/* Cycles to spend in D4 for writes */ |
| 249 |
#define HPC3_DMACFG_D4W_MASK 0x00003c00 |
| 250 |
#define HPC3_DMACFG_D4W_SHIFT 10 |
| 251 |
/* Cycles to spend in D5 for writes */ |
| 252 |
#define HPC3_DMACFG_D5W_MASK 0x0003c000 |
| 253 |
#define HPC3_DMACFG_D5W_SHIFT 14 |
| 254 |
/* Enable 16-bit DMA access mode */ |
| 255 |
#define HPC3_DMACFG_DS16 0x00040000 |
| 256 |
/* Places halfwords on high 16 bits of bus */ |
| 257 |
#define HPC3_DMACFG_EVENHI 0x00080000 |
| 258 |
/* Make this device real time */ |
| 259 |
#define HPC3_DMACFG_RTIME 0x00200000 |
| 260 |
/* 5 bit burst count for DMA device */ |
| 261 |
#define HPC3_DMACFG_BURST_MASK 0x07c00000 |
| 262 |
#define HPC3_DMACFG_BURST_SHIFT 22 |
| 263 |
/* Use live pbus_dreq unsynchronized signal */ |
| 264 |
#define HPC3_DMACFG_DRQLIVE 0x08000000 |
| 265 |
volatile u32 pbus_piocfg[16][64]; |
| 266 |
/* Cycles to spend in P2 state for reads */ |
| 267 |
#define HPC3_PIOCFG_P2R_MASK 0x00001 |
| 268 |
#define HPC3_PIOCFG_P2R_SHIFT 0 |
| 269 |
/* Cycles to spend in P3 state for reads */ |
| 270 |
#define HPC3_PIOCFG_P3R_MASK 0x0001e |
| 271 |
#define HPC3_PIOCFG_P3R_SHIFT 1 |
| 272 |
/* Cycles to spend in P4 state for reads */ |
| 273 |
#define HPC3_PIOCFG_P4R_MASK 0x001e0 |
| 274 |
#define HPC3_PIOCFG_P4R_SHIFT 5 |
| 275 |
/* Cycles to spend in P2 state for writes */ |
| 276 |
#define HPC3_PIOCFG_P2W_MASK 0x00200 |
| 277 |
#define HPC3_PIOCFG_P2W_SHIFT 9 |
| 278 |
/* Cycles to spend in P3 state for writes */ |
| 279 |
#define HPC3_PIOCFG_P3W_MASK 0x03c00 |
| 280 |
#define HPC3_PIOCFG_P3W_SHIFT 10 |
| 281 |
/* Cycles to spend in P4 state for writes */ |
| 282 |
#define HPC3_PIOCFG_P4W_MASK 0x3c000 |
| 283 |
#define HPC3_PIOCFG_P4W_SHIFT 14 |
| 284 |
/* Enable 16-bit PIO accesses */ |
| 285 |
#define HPC3_PIOCFG_DS16 0x40000 |
| 286 |
/* Place even address bits in bits <15:8> */ |
| 287 |
#define HPC3_PIOCFG_EVENHI 0x80000 |
| 288 |
|
| 289 |
/* PBUS PROM control regs. */ |
| 290 |
volatile u32 pbus_promwe; /* PROM write enable register */ |
| 291 |
#define HPC3_PROM_WENAB 0x1 /* Enable writes to the PROM */ |
| 292 |
|
| 293 |
u32 _unused5[0x0800/4 - 1]; |
| 294 |
volatile u32 pbus_promswap; /* Chip select swap reg */ |
| 295 |
#define HPC3_PROM_SWAP 0x1 /* invert GIO addr bit to select prom0 or prom1 */ |
| 296 |
|
| 297 |
u32 _unused6[0x0800/4 - 1]; |
| 298 |
volatile u32 pbus_gout; /* PROM general purpose output reg */ |
| 299 |
#define HPC3_PROM_STAT 0x1 /* General purpose status bit in gout */ |
| 300 |
|
| 301 |
u32 _unused7[0x1000/4 - 1]; |
| 302 |
volatile u32 rtcregs[14]; /* Dallas clock registers */ |
| 303 |
u32 _unused8[50]; |
| 304 |
volatile u32 bbram[8192-50-14]; /* Battery backed ram */ |
| 305 |
}; |
| 306 |
|
| 307 |
/* |
| 308 |
* It is possible to have two HPC3's within the address space on |
| 309 |
* one machine, though only having one is more likely on an Indy. |
| 310 |
*/ |
| 311 |
extern struct hpc3_regs *hpc3c0, *hpc3c1; |
| 312 |
#define HPC3_CHIP0_BASE 0x1fb80000 /* physical */ |
| 313 |
#define HPC3_CHIP1_BASE 0x1fb00000 /* physical */ |
| 314 |
|
| 315 |
extern void sgihpc_init(void); |
| 316 |
|
| 317 |
#endif /* _SGI_HPC3_H */ |