| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Device Tree file for Technologic Systems ts7250 board based on Cirrus EP9302 SoC |
| 4 |
*/ |
| 5 |
/dts-v1/; |
| 6 |
#include "ep93xx.dtsi" |
| 7 |
|
| 8 |
/ { |
| 9 |
compatible = "technologic,ts7250", "cirrus,ep9301"; |
| 10 |
model = "TS-7250 SBC"; |
| 11 |
#address-cells = <1>; |
| 12 |
#size-cells = <1>; |
| 13 |
|
| 14 |
chosen { |
| 15 |
}; |
| 16 |
|
| 17 |
memory@0 { |
| 18 |
device_type = "memory"; |
| 19 |
/* should be set from ATAGS */ |
| 20 |
reg = <0x00000000 0x02000000>, |
| 21 |
<0x000530c0 0x01fdd000>; |
| 22 |
}; |
| 23 |
|
| 24 |
leds { |
| 25 |
compatible = "gpio-leds"; |
| 26 |
led-0 { |
| 27 |
label = "grled"; |
| 28 |
gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>; |
| 29 |
linux,default-trigger = "heartbeat"; |
| 30 |
function = LED_FUNCTION_HEARTBEAT; |
| 31 |
}; |
| 32 |
|
| 33 |
led-1 { |
| 34 |
label = "rdled"; |
| 35 |
gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>; |
| 36 |
function = LED_FUNCTION_FAULT; |
| 37 |
}; |
| 38 |
}; |
| 39 |
}; |
| 40 |
|
| 41 |
&ebi { |
| 42 |
nand-controller@60000000 { |
| 43 |
compatible = "technologic,ts7200-nand"; |
| 44 |
reg = <0x60000000 0x8000000>; |
| 45 |
#address-cells = <1>; |
| 46 |
#size-cells = <0>; |
| 47 |
|
| 48 |
nand@0 { |
| 49 |
reg = <0>; |
| 50 |
partitions { |
| 51 |
compatible = "fixed-partitions"; |
| 52 |
#address-cells = <1>; |
| 53 |
#size-cells = <1>; |
| 54 |
|
| 55 |
partition@0 { |
| 56 |
label = "TS-BOOTROM"; |
| 57 |
reg = <0x00000000 0x00020000>; |
| 58 |
read-only; |
| 59 |
}; |
| 60 |
|
| 61 |
partition@20000 { |
| 62 |
label = "Linux"; |
| 63 |
reg = <0x00020000 0x07d00000>; |
| 64 |
}; |
| 65 |
|
| 66 |
partition@7d20000 { |
| 67 |
label = "RedBoot"; |
| 68 |
reg = <0x07d20000 0x002e0000>; |
| 69 |
read-only; |
| 70 |
}; |
| 71 |
}; |
| 72 |
}; |
| 73 |
}; |
| 74 |
|
| 75 |
rtc@10800000 { |
| 76 |
compatible = "st,m48t86"; |
| 77 |
reg = <0x10800000 0x1>, |
| 78 |
<0x11700000 0x1>; |
| 79 |
}; |
| 80 |
|
| 81 |
watchdog@23800000 { |
| 82 |
compatible = "technologic,ts7200-wdt"; |
| 83 |
reg = <0x23800000 0x01>, |
| 84 |
<0x23c00000 0x01>; |
| 85 |
timeout-sec = <30>; |
| 86 |
}; |
| 87 |
}; |
| 88 |
|
| 89 |
ð0 { |
| 90 |
phy-handle = <&phy0>; |
| 91 |
}; |
| 92 |
|
| 93 |
&gpio1 { |
| 94 |
/* PWM */ |
| 95 |
gpio-ranges = <&syscon 6 163 1>; |
| 96 |
}; |
| 97 |
|
| 98 |
/* ts7250 doesn't have GPIO Port D present */ |
| 99 |
&gpio3 { |
| 100 |
status = "disabled"; |
| 101 |
}; |
| 102 |
|
| 103 |
&gpio4 { |
| 104 |
gpio-ranges = <&syscon 0 97 2>; |
| 105 |
}; |
| 106 |
|
| 107 |
&gpio6 { |
| 108 |
gpio-ranges = <&syscon 0 87 2>; |
| 109 |
}; |
| 110 |
|
| 111 |
&gpio7 { |
| 112 |
gpio-ranges = <&syscon 2 199 4>; |
| 113 |
}; |
| 114 |
|
| 115 |
&spi0 { |
| 116 |
cs-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>; |
| 117 |
dmas = <&dma1 10 2>, <&dma1 10 1>; |
| 118 |
dma-names = "rx", "tx"; |
| 119 |
status = "okay"; |
| 120 |
|
| 121 |
tmp122: temperature-sensor@0 { |
| 122 |
compatible = "ti,tmp122"; |
| 123 |
reg = <0>; |
| 124 |
spi-max-frequency = <2000000>; |
| 125 |
}; |
| 126 |
}; |
| 127 |
|
| 128 |
&mdio0 { |
| 129 |
phy0: ethernet-phy@1 { |
| 130 |
reg = <1>; |
| 131 |
device_type = "ethernet-phy"; |
| 132 |
}; |
| 133 |
}; |
| 134 |
|
| 135 |
&uart0 { |
| 136 |
status = "okay"; |
| 137 |
}; |
| 138 |
|
| 139 |
&uart1 { |
| 140 |
status = "okay"; |
| 141 |
}; |
| 142 |
|
| 143 |
&usb0 { |
| 144 |
status = "okay"; |
| 145 |
}; |