| 1 |
.. SPDX-License-Identifier: GPL-2.0 |
| 2 |
|
| 3 |
The Radiotrack radio driver |
| 4 |
=========================== |
| 5 |
|
| 6 |
Author: Stephen M. Benoit <[email protected]> |
| 7 |
|
| 8 |
Date: Dec 14, 1996 |
| 9 |
|
| 10 |
ACKNOWLEDGMENTS |
| 11 |
---------------- |
| 12 |
|
| 13 |
This document was made based on 'C' code for Linux from Gideon le Grange |
| 14 |
([email protected] or [email protected]) in 1994, and elaborations from |
| 15 |
Frans Brinkman ([email protected]) in 1996. The results reported here are from |
| 16 |
experiments that the author performed on his own setup, so your mileage may |
| 17 |
vary... I make no guarantees, claims or warranties to the suitability or |
| 18 |
validity of this information. No other documentation on the AIMS |
| 19 |
Lab (http://www.aimslab.com/) RadioTrack card was made available to the |
| 20 |
author. This document is offered in the hopes that it might help users who |
| 21 |
want to use the RadioTrack card in an environment other than MS Windows. |
| 22 |
|
| 23 |
WHY THIS DOCUMENT? |
| 24 |
------------------ |
| 25 |
|
| 26 |
I have a RadioTrack card from back when I ran an MS-Windows platform. After |
| 27 |
converting to Linux, I found Gideon le Grange's command-line software for |
| 28 |
running the card, and found that it was good! Frans Brinkman made a |
| 29 |
comfortable X-windows interface, and added a scanning feature. For hack |
| 30 |
value, I wanted to see if the tuner could be tuned beyond the usual FM radio |
| 31 |
broadcast band, so I could pick up the audio carriers from North American |
| 32 |
broadcast TV channels, situated just below and above the 87.0-109.0 MHz range. |
| 33 |
I did not get much success, but I learned about programming ioports under |
| 34 |
Linux and gained some insights about the hardware design used for the card. |
| 35 |
|
| 36 |
So, without further delay, here are the details. |
| 37 |
|
| 38 |
|
| 39 |
PHYSICAL DESCRIPTION |
| 40 |
-------------------- |
| 41 |
|
| 42 |
The RadioTrack card is an ISA 8-bit FM radio card. The radio frequency (RF) |
| 43 |
input is simply an antenna lead, and the output is a power audio signal |
| 44 |
available through a miniature phone plug. Its RF frequencies of operation are |
| 45 |
more or less limited from 87.0 to 109.0 MHz (the commercial FM broadcast |
| 46 |
band). Although the registers can be programmed to request frequencies beyond |
| 47 |
these limits, experiments did not give promising results. The variable |
| 48 |
frequency oscillator (VFO) that demodulates the intermediate frequency (IF) |
| 49 |
signal probably has a small range of useful frequencies, and wraps around or |
| 50 |
gets clipped beyond the limits mentioned above. |
| 51 |
|
| 52 |
|
| 53 |
CONTROLLING THE CARD WITH IOPORT |
| 54 |
-------------------------------- |
| 55 |
|
| 56 |
The RadioTrack (base) ioport is configurable for 0x30c or 0x20c. Only one |
| 57 |
ioport seems to be involved. The ioport decoding circuitry must be pretty |
| 58 |
simple, as individual ioport bits are directly matched to specific functions |
| 59 |
(or blocks) of the radio card. This way, many functions can be changed in |
| 60 |
parallel with one write to the ioport. The only feedback available through |
| 61 |
the ioports appears to be the "Stereo Detect" bit. |
| 62 |
|
| 63 |
The bits of the ioport are arranged as follows: |
| 64 |
|
| 65 |
.. code-block:: none |
| 66 |
|
| 67 |
MSb LSb |
| 68 |
+------+------+------+--------+--------+-------+---------+--------+ |
| 69 |
| VolA | VolB | ???? | Stereo | Radio | TuneA | TuneB | Tune | |
| 70 |
| (+) | (-) | | Detect | Audio | (bit) | (latch) | Update | |
| 71 |
| | | | Enable | Enable | | | Enable | |
| 72 |
+------+------+------+--------+--------+-------+---------+--------+ |
| 73 |
|
| 74 |
|
| 75 |
==== ==== ================================= |
| 76 |
VolA VolB Description |
| 77 |
==== ==== ================================= |
| 78 |
0 0 audio mute |
| 79 |
0 1 volume + (some delay required) |
| 80 |
1 0 volume - (some delay required) |
| 81 |
1 1 stay at present volume |
| 82 |
==== ==== ================================= |
| 83 |
|
| 84 |
==================== =========== |
| 85 |
Stereo Detect Enable Description |
| 86 |
==================== =========== |
| 87 |
0 No Detect |
| 88 |
1 Detect |
| 89 |
==================== =========== |
| 90 |
|
| 91 |
Results available by reading ioport >60 msec after last port write. |
| 92 |
|
| 93 |
0xff ==> no stereo detected, 0xfd ==> stereo detected. |
| 94 |
|
| 95 |
============================= ============================= |
| 96 |
Radio to Audio (path) Enable Description |
| 97 |
============================= ============================= |
| 98 |
0 Disable path (silence) |
| 99 |
1 Enable path (audio produced) |
| 100 |
============================= ============================= |
| 101 |
|
| 102 |
===== ===== ================== |
| 103 |
TuneA TuneB Description |
| 104 |
===== ===== ================== |
| 105 |
0 0 "zero" bit phase 1 |
| 106 |
0 1 "zero" bit phase 2 |
| 107 |
1 0 "one" bit phase 1 |
| 108 |
1 1 "one" bit phase 2 |
| 109 |
===== ===== ================== |
| 110 |
|
| 111 |
|
| 112 |
24-bit code, where bits = (freq*40) + 10486188. |
| 113 |
The Most Significant 11 bits must be 1010 xxxx 0x0 to be valid. |
| 114 |
The bits are shifted in LSb first. |
| 115 |
|
| 116 |
================== =========================== |
| 117 |
Tune Update Enable Description |
| 118 |
================== =========================== |
| 119 |
0 Tuner held constant |
| 120 |
1 Tuner updating in progress |
| 121 |
================== =========================== |
| 122 |
|
| 123 |
|
| 124 |
PROGRAMMING EXAMPLES |
| 125 |
-------------------- |
| 126 |
|
| 127 |
.. code-block:: none |
| 128 |
|
| 129 |
Default: BASE <-- 0xc8 (current volume, no stereo detect, |
| 130 |
radio enable, tuner adjust disable) |
| 131 |
|
| 132 |
Card Off: BASE <-- 0x00 (audio mute, no stereo detect, |
| 133 |
radio disable, tuner adjust disable) |
| 134 |
|
| 135 |
Card On: BASE <-- 0x00 (see "Card Off", clears any unfinished business) |
| 136 |
BASE <-- 0xc8 (see "Default") |
| 137 |
|
| 138 |
Volume Down: BASE <-- 0x48 (volume down, no stereo detect, |
| 139 |
radio enable, tuner adjust disable) |
| 140 |
wait 10 msec |
| 141 |
BASE <-- 0xc8 (see "Default") |
| 142 |
|
| 143 |
Volume Up: BASE <-- 0x88 (volume up, no stereo detect, |
| 144 |
radio enable, tuner adjust disable) |
| 145 |
wait 10 msec |
| 146 |
BASE <-- 0xc8 (see "Default") |
| 147 |
|
| 148 |
Check Stereo: BASE <-- 0xd8 (current volume, stereo detect, |
| 149 |
radio enable, tuner adjust disable) |
| 150 |
wait 100 msec |
| 151 |
x <-- BASE (read ioport) |
| 152 |
BASE <-- 0xc8 (see "Default") |
| 153 |
|
| 154 |
x=0xff ==> "not stereo", x=0xfd ==> "stereo detected" |
| 155 |
|
| 156 |
Set Frequency: code = (freq*40) + 10486188 |
| 157 |
foreach of the 24 bits in code, |
| 158 |
(from Least to Most Significant): |
| 159 |
to write a "zero" bit, |
| 160 |
BASE <-- 0x01 (audio mute, no stereo detect, radio |
| 161 |
disable, "zero" bit phase 1, tuner adjust) |
| 162 |
BASE <-- 0x03 (audio mute, no stereo detect, radio |
| 163 |
disable, "zero" bit phase 2, tuner adjust) |
| 164 |
to write a "one" bit, |
| 165 |
BASE <-- 0x05 (audio mute, no stereo detect, radio |
| 166 |
disable, "one" bit phase 1, tuner adjust) |
| 167 |
BASE <-- 0x07 (audio mute, no stereo detect, radio |
| 168 |
disable, "one" bit phase 2, tuner adjust) |