| 1 |
.. SPDX-License-Identifier: GPL-2.0 |
| 2 |
|
| 3 |
The cx88 driver |
| 4 |
=============== |
| 5 |
|
| 6 |
Author: Gerd Hoffmann |
| 7 |
|
| 8 |
Documentation missing at the cx88 datasheet |
| 9 |
------------------------------------------- |
| 10 |
|
| 11 |
MO_OUTPUT_FORMAT (0x310164) |
| 12 |
|
| 13 |
.. code-block:: none |
| 14 |
|
| 15 |
Previous default from DScaler: 0x1c1f0008 |
| 16 |
Digit 8: 31-28 |
| 17 |
28: PREVREMOD = 1 |
| 18 |
|
| 19 |
Digit 7: 27-24 (0xc = 12 = b1100 ) |
| 20 |
27: COMBALT = 1 |
| 21 |
26: PAL_INV_PHASE |
| 22 |
(DScaler apparently set this to 1, resulted in sucky picture) |
| 23 |
|
| 24 |
Digits 6,5: 23-16 |
| 25 |
25-16: COMB_RANGE = 0x1f [default] (9 bits -> max 512) |
| 26 |
|
| 27 |
Digit 4: 15-12 |
| 28 |
15: DISIFX = 0 |
| 29 |
14: INVCBF = 0 |
| 30 |
13: DISADAPT = 0 |
| 31 |
12: NARROWADAPT = 0 |
| 32 |
|
| 33 |
Digit 3: 11-8 |
| 34 |
11: FORCE2H |
| 35 |
10: FORCEREMD |
| 36 |
9: NCHROMAEN |
| 37 |
8: NREMODEN |
| 38 |
|
| 39 |
Digit 2: 7-4 |
| 40 |
7-6: YCORE |
| 41 |
5-4: CCORE |
| 42 |
|
| 43 |
Digit 1: 3-0 |
| 44 |
3: RANGE = 1 |
| 45 |
2: HACTEXT |
| 46 |
1: HSFMT |
| 47 |
|
| 48 |
0x47 is the sync byte for MPEG-2 transport stream packets. |
| 49 |
Datasheet incorrectly states to use 47 decimal. 188 is the length. |
| 50 |
All DVB compliant frontends output packets with this start code. |
| 51 |
|
| 52 |
Hauppauge WinTV cx88 IR information |
| 53 |
----------------------------------- |
| 54 |
|
| 55 |
The controls for the mux are GPIO [0,1] for source, and GPIO 2 for muting. |
| 56 |
|
| 57 |
====== ======== ================================================= |
| 58 |
GPIO0 GPIO1 |
| 59 |
====== ======== ================================================= |
| 60 |
0 0 TV Audio |
| 61 |
1 0 FM radio |
| 62 |
0 1 Line-In |
| 63 |
1 1 Mono tuner bypass or CD passthru (tuner specific) |
| 64 |
====== ======== ================================================= |
| 65 |
|
| 66 |
GPIO 16(I believe) is tied to the IR port (if present). |
| 67 |
|
| 68 |
|
| 69 |
From the data sheet: |
| 70 |
|
| 71 |
- Register 24'h20004 PCI Interrupt Status |
| 72 |
|
| 73 |
- bit [18] IR_SMP_INT Set when 32 input samples have been collected over |
| 74 |
- gpio[16] pin into GP_SAMPLE register. |
| 75 |
|
| 76 |
What's missing from the data sheet: |
| 77 |
|
| 78 |
- Setup 4KHz sampling rate (roughly 2x oversampled; good enough for our RC5 |
| 79 |
compat remote) |
| 80 |
- set register 0x35C050 to 0xa80a80 |
| 81 |
- enable sampling |
| 82 |
- set register 0x35C054 to 0x5 |
| 83 |
- enable the IRQ bit 18 in the interrupt mask register (and |
| 84 |
provide for a handler) |
| 85 |
|
| 86 |
GP_SAMPLE register is at 0x35C058 |
| 87 |
|
| 88 |
Bits are then right shifted into the GP_SAMPLE register at the specified |
| 89 |
rate; you get an interrupt when a full DWORD is received. |
| 90 |
You need to recover the actual RC5 bits out of the (oversampled) IR sensor |
| 91 |
bits. (Hint: look for the 0/1and 1/0 crossings of the RC5 bi-phase data) An |
| 92 |
actual raw RC5 code will span 2-3 DWORDS, depending on the actual alignment. |
| 93 |
|
| 94 |
I'm pretty sure when no IR signal is present the receiver is always in a |
| 95 |
marking state(1); but stray light, etc can cause intermittent noise values |
| 96 |
as well. Remember, this is a free running sample of the IR receiver state |
| 97 |
over time, so don't assume any sample starts at any particular place. |
| 98 |
|
| 99 |
Additional info |
| 100 |
~~~~~~~~~~~~~~~ |
| 101 |
|
| 102 |
This data sheet (google search) seems to have a lovely description of the |
| 103 |
RC5 basics: |
| 104 |
http://www.atmel.com/dyn/resources/prod_documents/doc2817.pdf |
| 105 |
|
| 106 |
This document has more data: |
| 107 |
http://www.nenya.be/beor/electronics/rc5.htm |
| 108 |
|
| 109 |
This document has a how to decode a bi-phase data stream: |
| 110 |
http://www.ee.washington.edu/circuit_archive/text/ir_decode.txt |
| 111 |
|
| 112 |
This document has still more info: |
| 113 |
http://www.xs4all.nl/~sbp/knowledge/ir/rc5.htm |