| 1 |
--echo *** MDEV-7888: ANALYZE TABLE does wakeup_subsequent_commits(), causing wrong binlog order and parallel replication hang *** |
| 2 |
--source include/have_innodb.inc |
| 3 |
--source include/have_debug.inc |
| 4 |
--source include/have_debug_sync.inc |
| 5 |
--source include/master-slave.inc |
| 6 |
|
| 7 |
--connection server_2 |
| 8 |
SET @old_parallel_threads=@@GLOBAL.slave_parallel_threads; |
| 9 |
SET @old_parallel_mode=@@GLOBAL.slave_parallel_mode; |
| 10 |
--source include/stop_slave.inc |
| 11 |
SET GLOBAL slave_parallel_mode='conservative'; |
| 12 |
SET GLOBAL slave_parallel_threads=10; |
| 13 |
CHANGE MASTER TO master_use_gtid=slave_pos; |
| 14 |
--source include/start_slave.inc |
| 15 |
|
| 16 |
--connection server_1 |
| 17 |
ALTER TABLE mysql.gtid_slave_pos ENGINE=InnoDB; |
| 18 |
CREATE TABLE t2 (a int PRIMARY KEY) ENGINE=InnoDB; |
| 19 |
CREATE TABLE t3 (a INT PRIMARY KEY, b INT) ENGINE=InnoDB; |
| 20 |
--save_master_pos |
| 21 |
|
| 22 |
--connection server_2 |
| 23 |
--sync_with_master |
| 24 |
--source include/stop_slave.inc |
| 25 |
SET @old_dbug= @@GLOBAL.debug_dbug; |
| 26 |
SET GLOBAL debug_dbug= '+d,inject_analyze_table_sleep'; |
| 27 |
|
| 28 |
--connection server_1 |
| 29 |
# Inject two group commits. The bug was that ANALYZE TABLE would call |
| 30 |
# wakeup_subsequent_commits() too early, allowing the following transaction |
| 31 |
# in the same group to run ahead and binlog and free the GCO. Then we get |
| 32 |
# wrong binlog order and later access freed GCO, which causes lost wakeup |
| 33 |
# of following GCO and thus replication hang. |
| 34 |
# We injected a small sleep in ANALYZE to make the race easier to hit (this |
| 35 |
# can only cause false negatives in versions with the bug, not false positives, |
| 36 |
# so sleep is ok here. And it's in general not possible to trigger reliably |
| 37 |
# the race with debug_sync, since the bugfix makes the race impossible). |
| 38 |
|
| 39 |
SET @old_dbug= @@SESSION.debug_dbug; |
| 40 |
SET SESSION debug_dbug="+d,binlog_force_commit_id"; |
| 41 |
|
| 42 |
# Group commit with cid=10000, two event groups. |
| 43 |
SET @commit_id= 10000; |
| 44 |
ANALYZE TABLE t2; |
| 45 |
INSERT INTO t3 VALUES (120, 0); |
| 46 |
|
| 47 |
# Group commit with cid=10001, one event group. |
| 48 |
SET @commit_id= 10001; |
| 49 |
INSERT INTO t3 VALUES (121, 0); |
| 50 |
|
| 51 |
SET SESSION debug_dbug=@old_dbug; |
| 52 |
|
| 53 |
SELECT * FROM t3 WHERE a >= 120 ORDER BY a; |
| 54 |
--source include/save_master_gtid.inc |
| 55 |
|
| 56 |
--connection server_2 |
| 57 |
--source include/start_slave.inc |
| 58 |
--source include/sync_with_master_gtid.inc |
| 59 |
|
| 60 |
SELECT * FROM t3 WHERE a >= 120 ORDER BY a; |
| 61 |
|
| 62 |
# Clean up. |
| 63 |
--source include/stop_slave.inc |
| 64 |
SET GLOBAL debug_dbug= @old_dbug; |
| 65 |
SET GLOBAL slave_parallel_threads=@old_parallel_threads; |
| 66 |
SET GLOBAL slave_parallel_mode=@old_parallel_mode; |
| 67 |
--source include/start_slave.inc |
| 68 |
|
| 69 |
--connection server_1 |
| 70 |
DROP TABLE t2,t3; |
| 71 |
|
| 72 |
--source include/rpl_end.inc |
| 73 |
|