| 1 |
# ==== Purpose ==== |
| 2 |
# |
| 3 |
# Test verifies that, due to a temporary network error, if request dump |
| 4 |
# command specific packet write operation fails then the write error gets |
| 5 |
# handled appropriately. Further retry will be initiated with appropriate |
| 6 |
# slave registration on master. This will ensure that master has all the |
| 7 |
# details of slave and no warnings are reported on the master side. |
| 8 |
# |
| 9 |
# ==== Implementation ==== |
| 10 |
# |
| 11 |
# Steps: |
| 12 |
# 0 - Skip the slave start. |
| 13 |
# 1 - Enable debug simulation which will simulate packet write error during |
| 14 |
# dump request command execution. |
| 15 |
# 2 - Start the slave. Observe that slave is able to reconnect post |
| 16 |
# temporary network write error. |
| 17 |
# |
| 18 |
# ==== References ==== |
| 19 |
# |
| 20 |
# MDEV-14203: rpl.rpl_extra_col_master_myisam, |
| 21 |
# rpl.rpl_slave_load_tmpdir_not_exist failed in buildbot with a |
| 22 |
# warning |
| 23 |
# |
| 24 |
# MDEV-13258: rpl.rpl_skip_replication, rpl.rpl_set_statement_default_master |
| 25 |
# failed in buildbot |
| 26 |
# |
| 27 |
|
| 28 |
--source include/have_debug.inc |
| 29 |
--source include/have_debug_sync.inc |
| 30 |
--let $rpl_skip_start_slave=1 |
| 31 |
--source include/master-slave.inc |
| 32 |
|
| 33 |
--disable_query_log |
| 34 |
call mtr.add_suppression("Could not read packet:.* errno: 11"); |
| 35 |
--enable_query_log |
| 36 |
|
| 37 |
# Do an insert on master |
| 38 |
CREATE TABLE t1(a int); |
| 39 |
INSERT INTO t1 VALUES(1); |
| 40 |
|
| 41 |
# Add a debug point and start the slave so that dump request fails. |
| 42 |
connection slave; |
| 43 |
SET @saved_dbug = @@GLOBAL.debug_dbug; |
| 44 |
SET @@global.debug_dbug= 'd,simulate_error_on_packet_write'; |
| 45 |
|
| 46 |
START SLAVE; |
| 47 |
SET DEBUG_SYNC= 'now WAIT_FOR parked'; |
| 48 |
SET @@GLOBAL.debug_dbug = @saved_dbug; |
| 49 |
SET DEBUG_SYNC= 'now SIGNAL continue'; |
| 50 |
|
| 51 |
# Ensure the last DEBUG_SYNC signal was received by the target thread before |
| 52 |
# reset; otherwise, the reset can drop the last signal before it gets |
| 53 |
# acknowledged |
| 54 |
let $wait_condition= select count(*)=0 from information_schema.processlist where state like "%debug%"; |
| 55 |
source include/wait_condition.inc; |
| 56 |
SET DEBUG_SYNC= 'RESET'; |
| 57 |
|
| 58 |
--source include/wait_for_slave_io_to_start.inc |
| 59 |
--source include/wait_for_slave_sql_to_start.inc |
| 60 |
|
| 61 |
# Sync the slave and verify that slave has caught up with the master. |
| 62 |
connection master; |
| 63 |
--source include/sync_slave_sql_with_master.inc |
| 64 |
SELECT * FROM t1; |
| 65 |
|
| 66 |
# Cleanup |
| 67 |
connection master; |
| 68 |
DROP TABLE t1; |
| 69 |
|
| 70 |
--source include/rpl_end.inc |