| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Copyright (c) 2012 - 2018 Microchip Technology Inc., and its subsidiaries. |
| 4 |
* All rights reserved. |
| 5 |
*/ |
| 6 |
|
| 7 |
#include <linux/clk.h> |
| 8 |
#include <linux/spi/spi.h> |
| 9 |
#include <linux/crc7.h> |
| 10 |
#include <linux/crc-itu-t.h> |
| 11 |
#include <linux/gpio/consumer.h> |
| 12 |
|
| 13 |
#include "netdev.h" |
| 14 |
#include "cfg80211.h" |
| 15 |
|
| 16 |
#define SPI_MODALIAS "wilc1000_spi" |
| 17 |
|
| 18 |
static bool enable_crc7; /* protect SPI commands with CRC7 */ |
| 19 |
module_param(enable_crc7, bool, 0644); |
| 20 |
MODULE_PARM_DESC(enable_crc7, |
| 21 |
"Enable CRC7 checksum to protect command transfers\n" |
| 22 |
"\t\t\tagainst corruption during the SPI transfer.\n" |
| 23 |
"\t\t\tCommand transfers are short and the CPU-cycle cost\n" |
| 24 |
"\t\t\tof enabling this is small."); |
| 25 |
|
| 26 |
static bool enable_crc16; /* protect SPI data with CRC16 */ |
| 27 |
module_param(enable_crc16, bool, 0644); |
| 28 |
MODULE_PARM_DESC(enable_crc16, |
| 29 |
"Enable CRC16 checksum to protect data transfers\n" |
| 30 |
"\t\t\tagainst corruption during the SPI transfer.\n" |
| 31 |
"\t\t\tData transfers can be large and the CPU-cycle cost\n" |
| 32 |
"\t\t\tof enabling this may be substantial."); |
| 33 |
|
| 34 |
/* |
| 35 |
* For CMD_SINGLE_READ and CMD_INTERNAL_READ, WILC may insert one or |
| 36 |
* more zero bytes between the command response and the DATA Start tag |
| 37 |
* (0xf3). This behavior appears to be undocumented in "ATWILC1000 |
| 38 |
* USER GUIDE" (https://tinyurl.com/4hhshdts) but we have observed 1-4 |
| 39 |
* zero bytes when the SPI bus operates at 48MHz and none when it |
| 40 |
* operates at 1MHz. |
| 41 |
*/ |
| 42 |
#define WILC_SPI_RSP_HDR_EXTRA_DATA 8 |
| 43 |
|
| 44 |
struct wilc_spi { |
| 45 |
bool isinit; /* true if wilc_spi_init was successful */ |
| 46 |
bool probing_crc; /* true if we're probing chip's CRC config */ |
| 47 |
bool crc7_enabled; /* true if crc7 is currently enabled */ |
| 48 |
bool crc16_enabled; /* true if crc16 is currently enabled */ |
| 49 |
struct wilc_gpios { |
| 50 |
struct gpio_desc *enable; /* ENABLE GPIO or NULL */ |
| 51 |
struct gpio_desc *reset; /* RESET GPIO or NULL */ |
| 52 |
} gpios; |
| 53 |
}; |
| 54 |
|
| 55 |
static const struct wilc_hif_func wilc_hif_spi; |
| 56 |
|
| 57 |
static int wilc_spi_reset(struct wilc *wilc); |
| 58 |
static int wilc_spi_configure_bus_protocol(struct wilc *wilc); |
| 59 |
static int wilc_validate_chipid(struct wilc *wilc); |
| 60 |
|
| 61 |
/******************************************** |
| 62 |
* |
| 63 |
* Spi protocol Function |
| 64 |
* |
| 65 |
********************************************/ |
| 66 |
|
| 67 |
#define CMD_DMA_WRITE 0xc1 |
| 68 |
#define CMD_DMA_READ 0xc2 |
| 69 |
#define CMD_INTERNAL_WRITE 0xc3 |
| 70 |
#define CMD_INTERNAL_READ 0xc4 |
| 71 |
#define CMD_TERMINATE 0xc5 |
| 72 |
#define CMD_REPEAT 0xc6 |
| 73 |
#define CMD_DMA_EXT_WRITE 0xc7 |
| 74 |
#define CMD_DMA_EXT_READ 0xc8 |
| 75 |
#define CMD_SINGLE_WRITE 0xc9 |
| 76 |
#define CMD_SINGLE_READ 0xca |
| 77 |
#define CMD_RESET 0xcf |
| 78 |
|
| 79 |
#define SPI_RETRY_MAX_LIMIT 10 |
| 80 |
#define SPI_ENABLE_VMM_RETRY_LIMIT 2 |
| 81 |
|
| 82 |
/* SPI response fields (section 11.1.2 in ATWILC1000 User Guide): */ |
| 83 |
#define RSP_START_FIELD GENMASK(7, 4) |
| 84 |
#define RSP_TYPE_FIELD GENMASK(3, 0) |
| 85 |
|
| 86 |
/* SPI response values for the response fields: */ |
| 87 |
#define RSP_START_TAG 0xc |
| 88 |
#define RSP_TYPE_FIRST_PACKET 0x1 |
| 89 |
#define RSP_TYPE_INNER_PACKET 0x2 |
| 90 |
#define RSP_TYPE_LAST_PACKET 0x3 |
| 91 |
#define RSP_STATE_NO_ERROR 0x00 |
| 92 |
|
| 93 |
#define PROTOCOL_REG_PKT_SZ_MASK GENMASK(6, 4) |
| 94 |
#define PROTOCOL_REG_CRC16_MASK GENMASK(3, 3) |
| 95 |
#define PROTOCOL_REG_CRC7_MASK GENMASK(2, 2) |
| 96 |
|
| 97 |
/* |
| 98 |
* The SPI data packet size may be any integer power of two in the |
| 99 |
* range from 256 to 8192 bytes. |
| 100 |
*/ |
| 101 |
#define DATA_PKT_LOG_SZ_MIN 8 /* 256 B */ |
| 102 |
#define DATA_PKT_LOG_SZ_MAX 13 /* 8 KiB */ |
| 103 |
|
| 104 |
/* |
| 105 |
* Select the data packet size (log2 of number of bytes): Use the |
| 106 |
* maximum data packet size. We only retransmit complete packets, so |
| 107 |
* there is no benefit from using smaller data packets. |
| 108 |
*/ |
| 109 |
#define DATA_PKT_LOG_SZ DATA_PKT_LOG_SZ_MAX |
| 110 |
#define DATA_PKT_SZ (1 << DATA_PKT_LOG_SZ) |
| 111 |
|
| 112 |
#define WILC_SPI_COMMAND_STAT_SUCCESS 0 |
| 113 |
#define WILC_GET_RESP_HDR_START(h) (((h) >> 4) & 0xf) |
| 114 |
|
| 115 |
struct wilc_spi_cmd { |
| 116 |
u8 cmd_type; |
| 117 |
union { |
| 118 |
struct { |
| 119 |
u8 addr[3]; |
| 120 |
u8 crc[]; |
| 121 |
} __packed simple_cmd; |
| 122 |
struct { |
| 123 |
u8 addr[3]; |
| 124 |
u8 size[2]; |
| 125 |
u8 crc[]; |
| 126 |
} __packed dma_cmd; |
| 127 |
struct { |
| 128 |
u8 addr[3]; |
| 129 |
u8 size[3]; |
| 130 |
u8 crc[]; |
| 131 |
} __packed dma_cmd_ext; |
| 132 |
struct { |
| 133 |
u8 addr[2]; |
| 134 |
__be32 data; |
| 135 |
u8 crc[]; |
| 136 |
} __packed internal_w_cmd; |
| 137 |
struct { |
| 138 |
u8 addr[3]; |
| 139 |
__be32 data; |
| 140 |
u8 crc[]; |
| 141 |
} __packed w_cmd; |
| 142 |
} u; |
| 143 |
} __packed; |
| 144 |
|
| 145 |
struct wilc_spi_read_rsp_data { |
| 146 |
u8 header; |
| 147 |
u8 data[4]; |
| 148 |
u8 crc[]; |
| 149 |
} __packed; |
| 150 |
|
| 151 |
struct wilc_spi_rsp_data { |
| 152 |
u8 rsp_cmd_type; |
| 153 |
u8 status; |
| 154 |
u8 data[]; |
| 155 |
} __packed; |
| 156 |
|
| 157 |
struct wilc_spi_special_cmd_rsp { |
| 158 |
u8 skip_byte; |
| 159 |
u8 rsp_cmd_type; |
| 160 |
u8 status; |
| 161 |
} __packed; |
| 162 |
|
| 163 |
static int wilc_parse_gpios(struct wilc *wilc) |
| 164 |
{ |
| 165 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 166 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 167 |
struct wilc_gpios *gpios = &spi_priv->gpios; |
| 168 |
|
| 169 |
/* get ENABLE pin and deassert it (if it is defined): */ |
| 170 |
gpios->enable = devm_gpiod_get_optional(&spi->dev, |
| 171 |
"enable", GPIOD_OUT_LOW); |
| 172 |
/* get RESET pin and assert it (if it is defined): */ |
| 173 |
if (gpios->enable) { |
| 174 |
/* if enable pin exists, reset must exist as well */ |
| 175 |
gpios->reset = devm_gpiod_get(&spi->dev, |
| 176 |
"reset", GPIOD_OUT_HIGH); |
| 177 |
if (IS_ERR(gpios->reset)) { |
| 178 |
dev_err(&spi->dev, "missing reset gpio.\n"); |
| 179 |
return PTR_ERR(gpios->reset); |
| 180 |
} |
| 181 |
} else { |
| 182 |
gpios->reset = devm_gpiod_get_optional(&spi->dev, |
| 183 |
"reset", GPIOD_OUT_HIGH); |
| 184 |
} |
| 185 |
return 0; |
| 186 |
} |
| 187 |
|
| 188 |
static void wilc_wlan_power(struct wilc *wilc, bool on) |
| 189 |
{ |
| 190 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 191 |
struct wilc_gpios *gpios = &spi_priv->gpios; |
| 192 |
|
| 193 |
if (on) { |
| 194 |
/* assert ENABLE: */ |
| 195 |
gpiod_set_value(gpios->enable, 1); |
| 196 |
mdelay(5); |
| 197 |
/* deassert RESET: */ |
| 198 |
gpiod_set_value(gpios->reset, 0); |
| 199 |
} else { |
| 200 |
/* assert RESET: */ |
| 201 |
gpiod_set_value(gpios->reset, 1); |
| 202 |
/* deassert ENABLE: */ |
| 203 |
gpiod_set_value(gpios->enable, 0); |
| 204 |
} |
| 205 |
} |
| 206 |
|
| 207 |
static int wilc_bus_probe(struct spi_device *spi) |
| 208 |
{ |
| 209 |
struct wilc_spi *spi_priv; |
| 210 |
struct wilc_vif *vif; |
| 211 |
struct wilc *wilc; |
| 212 |
int ret; |
| 213 |
|
| 214 |
spi_priv = kzalloc_obj(*spi_priv); |
| 215 |
if (!spi_priv) |
| 216 |
return -ENOMEM; |
| 217 |
|
| 218 |
ret = wilc_cfg80211_init(&wilc, &spi->dev, WILC_HIF_SPI, &wilc_hif_spi); |
| 219 |
if (ret) |
| 220 |
goto free; |
| 221 |
|
| 222 |
spi_set_drvdata(spi, wilc); |
| 223 |
wilc->dev = &spi->dev; |
| 224 |
wilc->bus_data = spi_priv; |
| 225 |
wilc->dev_irq_num = spi->irq; |
| 226 |
|
| 227 |
ret = wilc_parse_gpios(wilc); |
| 228 |
if (ret < 0) |
| 229 |
goto netdev_cleanup; |
| 230 |
|
| 231 |
wilc->rtc_clk = devm_clk_get_optional_enabled(&spi->dev, "rtc"); |
| 232 |
if (IS_ERR(wilc->rtc_clk)) { |
| 233 |
ret = PTR_ERR(wilc->rtc_clk); |
| 234 |
goto netdev_cleanup; |
| 235 |
} |
| 236 |
|
| 237 |
dev_info(&spi->dev, "Selected CRC config: crc7=%s, crc16=%s\n", |
| 238 |
enable_crc7 ? "on" : "off", enable_crc16 ? "on" : "off"); |
| 239 |
|
| 240 |
/* we need power to configure the bus protocol and to read the chip id: */ |
| 241 |
|
| 242 |
wilc_wlan_power(wilc, true); |
| 243 |
|
| 244 |
ret = wilc_spi_configure_bus_protocol(wilc); |
| 245 |
if (ret) |
| 246 |
goto power_down; |
| 247 |
|
| 248 |
ret = wilc_get_chipid(wilc); |
| 249 |
if (ret) |
| 250 |
goto power_down; |
| 251 |
|
| 252 |
ret = wilc_cfg80211_register(wilc); |
| 253 |
if (ret) |
| 254 |
goto power_down; |
| 255 |
|
| 256 |
ret = wilc_load_mac_from_nv(wilc); |
| 257 |
if (ret) { |
| 258 |
pr_err("Can not retrieve MAC address from chip\n"); |
| 259 |
goto unregister_wiphy; |
| 260 |
} |
| 261 |
|
| 262 |
wilc_wlan_power(wilc, false); |
| 263 |
vif = wilc_netdev_ifc_init(wilc, "wlan%d", WILC_STATION_MODE, |
| 264 |
NL80211_IFTYPE_STATION, false); |
| 265 |
if (IS_ERR(vif)) { |
| 266 |
ret = PTR_ERR(vif); |
| 267 |
goto unregister_wiphy; |
| 268 |
} |
| 269 |
return 0; |
| 270 |
|
| 271 |
unregister_wiphy: |
| 272 |
wiphy_unregister(wilc->wiphy); |
| 273 |
power_down: |
| 274 |
wilc_wlan_power(wilc, false); |
| 275 |
netdev_cleanup: |
| 276 |
wilc_netdev_cleanup(wilc); |
| 277 |
wiphy_free(wilc->wiphy); |
| 278 |
free: |
| 279 |
kfree(spi_priv); |
| 280 |
return ret; |
| 281 |
} |
| 282 |
|
| 283 |
static void wilc_bus_remove(struct spi_device *spi) |
| 284 |
{ |
| 285 |
struct wilc *wilc = spi_get_drvdata(spi); |
| 286 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 287 |
|
| 288 |
wilc_netdev_cleanup(wilc); |
| 289 |
wiphy_unregister(wilc->wiphy); |
| 290 |
wiphy_free(wilc->wiphy); |
| 291 |
kfree(spi_priv); |
| 292 |
} |
| 293 |
|
| 294 |
static const struct of_device_id wilc_of_match[] = { |
| 295 |
{ .compatible = "microchip,wilc1000", }, |
| 296 |
{ /* sentinel */ } |
| 297 |
}; |
| 298 |
MODULE_DEVICE_TABLE(of, wilc_of_match); |
| 299 |
|
| 300 |
static const struct spi_device_id wilc_spi_id[] = { |
| 301 |
{ "wilc1000", 0 }, |
| 302 |
{ /* sentinel */ } |
| 303 |
}; |
| 304 |
MODULE_DEVICE_TABLE(spi, wilc_spi_id); |
| 305 |
|
| 306 |
static struct spi_driver wilc_spi_driver = { |
| 307 |
.driver = { |
| 308 |
.name = SPI_MODALIAS, |
| 309 |
.of_match_table = wilc_of_match, |
| 310 |
}, |
| 311 |
.id_table = wilc_spi_id, |
| 312 |
.probe = wilc_bus_probe, |
| 313 |
.remove = wilc_bus_remove, |
| 314 |
}; |
| 315 |
module_spi_driver(wilc_spi_driver); |
| 316 |
MODULE_DESCRIPTION("Atmel WILC1000 SPI wireless driver"); |
| 317 |
MODULE_LICENSE("GPL"); |
| 318 |
|
| 319 |
static int wilc_spi_tx(struct wilc *wilc, u8 *b, u32 len) |
| 320 |
{ |
| 321 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 322 |
int ret; |
| 323 |
struct spi_message msg; |
| 324 |
|
| 325 |
if (len > 0 && b) { |
| 326 |
struct spi_transfer tr = { |
| 327 |
.tx_buf = b, |
| 328 |
.len = len, |
| 329 |
.delay = { |
| 330 |
.value = 0, |
| 331 |
.unit = SPI_DELAY_UNIT_USECS |
| 332 |
}, |
| 333 |
}; |
| 334 |
char *r_buffer = kzalloc(len, GFP_KERNEL); |
| 335 |
|
| 336 |
if (!r_buffer) |
| 337 |
return -ENOMEM; |
| 338 |
|
| 339 |
tr.rx_buf = r_buffer; |
| 340 |
dev_dbg(&spi->dev, "Request writing %d bytes\n", len); |
| 341 |
|
| 342 |
memset(&msg, 0, sizeof(msg)); |
| 343 |
spi_message_init(&msg); |
| 344 |
spi_message_add_tail(&tr, &msg); |
| 345 |
|
| 346 |
ret = spi_sync(spi, &msg); |
| 347 |
if (ret < 0) |
| 348 |
dev_err(&spi->dev, "SPI transaction failed\n"); |
| 349 |
|
| 350 |
kfree(r_buffer); |
| 351 |
} else { |
| 352 |
dev_err(&spi->dev, |
| 353 |
"can't write data with the following length: %d\n", |
| 354 |
len); |
| 355 |
ret = -EINVAL; |
| 356 |
} |
| 357 |
|
| 358 |
return ret; |
| 359 |
} |
| 360 |
|
| 361 |
static int wilc_spi_rx(struct wilc *wilc, u8 *rb, u32 rlen) |
| 362 |
{ |
| 363 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 364 |
int ret; |
| 365 |
|
| 366 |
if (rlen > 0) { |
| 367 |
struct spi_message msg; |
| 368 |
struct spi_transfer tr = { |
| 369 |
.rx_buf = rb, |
| 370 |
.len = rlen, |
| 371 |
.delay = { |
| 372 |
.value = 0, |
| 373 |
.unit = SPI_DELAY_UNIT_USECS |
| 374 |
}, |
| 375 |
|
| 376 |
}; |
| 377 |
char *t_buffer = kzalloc(rlen, GFP_KERNEL); |
| 378 |
|
| 379 |
if (!t_buffer) |
| 380 |
return -ENOMEM; |
| 381 |
|
| 382 |
tr.tx_buf = t_buffer; |
| 383 |
|
| 384 |
memset(&msg, 0, sizeof(msg)); |
| 385 |
spi_message_init(&msg); |
| 386 |
spi_message_add_tail(&tr, &msg); |
| 387 |
|
| 388 |
ret = spi_sync(spi, &msg); |
| 389 |
if (ret < 0) |
| 390 |
dev_err(&spi->dev, "SPI transaction failed\n"); |
| 391 |
kfree(t_buffer); |
| 392 |
} else { |
| 393 |
dev_err(&spi->dev, |
| 394 |
"can't read data with the following length: %u\n", |
| 395 |
rlen); |
| 396 |
ret = -EINVAL; |
| 397 |
} |
| 398 |
|
| 399 |
return ret; |
| 400 |
} |
| 401 |
|
| 402 |
static int wilc_spi_tx_rx(struct wilc *wilc, u8 *wb, u8 *rb, u32 rlen) |
| 403 |
{ |
| 404 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 405 |
int ret; |
| 406 |
|
| 407 |
if (rlen > 0) { |
| 408 |
struct spi_message msg; |
| 409 |
struct spi_transfer tr = { |
| 410 |
.rx_buf = rb, |
| 411 |
.tx_buf = wb, |
| 412 |
.len = rlen, |
| 413 |
.bits_per_word = 8, |
| 414 |
.delay = { |
| 415 |
.value = 0, |
| 416 |
.unit = SPI_DELAY_UNIT_USECS |
| 417 |
}, |
| 418 |
|
| 419 |
}; |
| 420 |
|
| 421 |
memset(&msg, 0, sizeof(msg)); |
| 422 |
spi_message_init(&msg); |
| 423 |
spi_message_add_tail(&tr, &msg); |
| 424 |
ret = spi_sync(spi, &msg); |
| 425 |
if (ret < 0) |
| 426 |
dev_err(&spi->dev, "SPI transaction failed\n"); |
| 427 |
} else { |
| 428 |
dev_err(&spi->dev, |
| 429 |
"can't read data with the following length: %u\n", |
| 430 |
rlen); |
| 431 |
ret = -EINVAL; |
| 432 |
} |
| 433 |
|
| 434 |
return ret; |
| 435 |
} |
| 436 |
|
| 437 |
static int spi_data_write(struct wilc *wilc, u8 *b, u32 sz) |
| 438 |
{ |
| 439 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 440 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 441 |
int ix, nbytes; |
| 442 |
int result = 0; |
| 443 |
u8 cmd, order, crc[2]; |
| 444 |
u16 crc_calc; |
| 445 |
|
| 446 |
/* |
| 447 |
* Data |
| 448 |
*/ |
| 449 |
ix = 0; |
| 450 |
do { |
| 451 |
if (sz <= DATA_PKT_SZ) { |
| 452 |
nbytes = sz; |
| 453 |
order = 0x3; |
| 454 |
} else { |
| 455 |
nbytes = DATA_PKT_SZ; |
| 456 |
if (ix == 0) |
| 457 |
order = 0x1; |
| 458 |
else |
| 459 |
order = 0x02; |
| 460 |
} |
| 461 |
|
| 462 |
/* |
| 463 |
* Write command |
| 464 |
*/ |
| 465 |
cmd = 0xf0; |
| 466 |
cmd |= order; |
| 467 |
|
| 468 |
if (wilc_spi_tx(wilc, &cmd, 1)) { |
| 469 |
dev_err(&spi->dev, |
| 470 |
"Failed data block cmd write, bus error...\n"); |
| 471 |
result = -EINVAL; |
| 472 |
break; |
| 473 |
} |
| 474 |
|
| 475 |
/* |
| 476 |
* Write data |
| 477 |
*/ |
| 478 |
if (wilc_spi_tx(wilc, &b[ix], nbytes)) { |
| 479 |
dev_err(&spi->dev, |
| 480 |
"Failed data block write, bus error...\n"); |
| 481 |
result = -EINVAL; |
| 482 |
break; |
| 483 |
} |
| 484 |
|
| 485 |
/* |
| 486 |
* Write CRC |
| 487 |
*/ |
| 488 |
if (spi_priv->crc16_enabled) { |
| 489 |
crc_calc = crc_itu_t(0xffff, &b[ix], nbytes); |
| 490 |
crc[0] = crc_calc >> 8; |
| 491 |
crc[1] = crc_calc; |
| 492 |
if (wilc_spi_tx(wilc, crc, 2)) { |
| 493 |
dev_err(&spi->dev, "Failed data block crc write, bus error...\n"); |
| 494 |
result = -EINVAL; |
| 495 |
break; |
| 496 |
} |
| 497 |
} |
| 498 |
|
| 499 |
/* |
| 500 |
* No need to wait for response |
| 501 |
*/ |
| 502 |
ix += nbytes; |
| 503 |
sz -= nbytes; |
| 504 |
} while (sz); |
| 505 |
|
| 506 |
return result; |
| 507 |
} |
| 508 |
|
| 509 |
/******************************************** |
| 510 |
* |
| 511 |
* Spi Internal Read/Write Function |
| 512 |
* |
| 513 |
********************************************/ |
| 514 |
static u8 wilc_get_crc7(u8 *buffer, u32 len) |
| 515 |
{ |
| 516 |
return crc7_be(0xfe, buffer, len) | 0x01; |
| 517 |
} |
| 518 |
|
| 519 |
static int wilc_spi_single_read(struct wilc *wilc, u8 cmd, u32 adr, void *b, |
| 520 |
u8 clockless) |
| 521 |
{ |
| 522 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 523 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 524 |
u8 wb[32], rb[32]; |
| 525 |
int cmd_len, resp_len, i; |
| 526 |
u16 crc_calc, crc_recv; |
| 527 |
struct wilc_spi_cmd *c; |
| 528 |
struct wilc_spi_rsp_data *r; |
| 529 |
struct wilc_spi_read_rsp_data *r_data; |
| 530 |
|
| 531 |
memset(wb, 0x0, sizeof(wb)); |
| 532 |
memset(rb, 0x0, sizeof(rb)); |
| 533 |
c = (struct wilc_spi_cmd *)wb; |
| 534 |
c->cmd_type = cmd; |
| 535 |
if (cmd == CMD_SINGLE_READ) { |
| 536 |
c->u.simple_cmd.addr[0] = adr >> 16; |
| 537 |
c->u.simple_cmd.addr[1] = adr >> 8; |
| 538 |
c->u.simple_cmd.addr[2] = adr; |
| 539 |
} else if (cmd == CMD_INTERNAL_READ) { |
| 540 |
c->u.simple_cmd.addr[0] = adr >> 8; |
| 541 |
if (clockless == 1) |
| 542 |
c->u.simple_cmd.addr[0] |= BIT(7); |
| 543 |
c->u.simple_cmd.addr[1] = adr; |
| 544 |
c->u.simple_cmd.addr[2] = 0x0; |
| 545 |
} else { |
| 546 |
dev_err(&spi->dev, "cmd [%x] not supported\n", cmd); |
| 547 |
return -EINVAL; |
| 548 |
} |
| 549 |
|
| 550 |
cmd_len = offsetof(struct wilc_spi_cmd, u.simple_cmd.crc); |
| 551 |
resp_len = sizeof(*r) + sizeof(*r_data) + WILC_SPI_RSP_HDR_EXTRA_DATA; |
| 552 |
|
| 553 |
if (spi_priv->crc7_enabled) { |
| 554 |
c->u.simple_cmd.crc[0] = wilc_get_crc7(wb, cmd_len); |
| 555 |
cmd_len += 1; |
| 556 |
resp_len += 2; |
| 557 |
} |
| 558 |
|
| 559 |
if (cmd_len + resp_len > ARRAY_SIZE(wb)) { |
| 560 |
dev_err(&spi->dev, |
| 561 |
"spi buffer size too small (%d) (%d) (%zu)\n", |
| 562 |
cmd_len, resp_len, ARRAY_SIZE(wb)); |
| 563 |
return -EINVAL; |
| 564 |
} |
| 565 |
|
| 566 |
if (wilc_spi_tx_rx(wilc, wb, rb, cmd_len + resp_len)) { |
| 567 |
dev_err(&spi->dev, "Failed cmd write, bus error...\n"); |
| 568 |
return -EINVAL; |
| 569 |
} |
| 570 |
|
| 571 |
r = (struct wilc_spi_rsp_data *)&rb[cmd_len]; |
| 572 |
if (r->rsp_cmd_type != cmd && !clockless) { |
| 573 |
if (!spi_priv->probing_crc) |
| 574 |
dev_err(&spi->dev, |
| 575 |
"Failed cmd, cmd (%02x), resp (%02x)\n", |
| 576 |
cmd, r->rsp_cmd_type); |
| 577 |
return -EINVAL; |
| 578 |
} |
| 579 |
|
| 580 |
if (r->status != WILC_SPI_COMMAND_STAT_SUCCESS && !clockless) { |
| 581 |
dev_err(&spi->dev, "Failed cmd state response state (%02x)\n", |
| 582 |
r->status); |
| 583 |
return -EINVAL; |
| 584 |
} |
| 585 |
|
| 586 |
for (i = 0; i < WILC_SPI_RSP_HDR_EXTRA_DATA; ++i) |
| 587 |
if (WILC_GET_RESP_HDR_START(r->data[i]) == 0xf) |
| 588 |
break; |
| 589 |
|
| 590 |
if (i >= WILC_SPI_RSP_HDR_EXTRA_DATA) { |
| 591 |
dev_err(&spi->dev, "Error, data start missing\n"); |
| 592 |
return -EINVAL; |
| 593 |
} |
| 594 |
|
| 595 |
r_data = (struct wilc_spi_read_rsp_data *)&r->data[i]; |
| 596 |
|
| 597 |
if (b) |
| 598 |
memcpy(b, r_data->data, 4); |
| 599 |
|
| 600 |
if (!clockless && spi_priv->crc16_enabled) { |
| 601 |
crc_recv = (r_data->crc[0] << 8) | r_data->crc[1]; |
| 602 |
crc_calc = crc_itu_t(0xffff, r_data->data, 4); |
| 603 |
if (crc_recv != crc_calc) { |
| 604 |
dev_err(&spi->dev, "%s: bad CRC 0x%04x " |
| 605 |
"(calculated 0x%04x)\n", __func__, |
| 606 |
crc_recv, crc_calc); |
| 607 |
return -EINVAL; |
| 608 |
} |
| 609 |
} |
| 610 |
|
| 611 |
return 0; |
| 612 |
} |
| 613 |
|
| 614 |
static int wilc_spi_write_cmd(struct wilc *wilc, u8 cmd, u32 adr, u32 data, |
| 615 |
u8 clockless) |
| 616 |
{ |
| 617 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 618 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 619 |
u8 wb[32], rb[32]; |
| 620 |
int cmd_len, resp_len; |
| 621 |
struct wilc_spi_cmd *c; |
| 622 |
struct wilc_spi_rsp_data *r; |
| 623 |
|
| 624 |
memset(wb, 0x0, sizeof(wb)); |
| 625 |
memset(rb, 0x0, sizeof(rb)); |
| 626 |
c = (struct wilc_spi_cmd *)wb; |
| 627 |
c->cmd_type = cmd; |
| 628 |
if (cmd == CMD_INTERNAL_WRITE) { |
| 629 |
c->u.internal_w_cmd.addr[0] = adr >> 8; |
| 630 |
if (clockless == 1) |
| 631 |
c->u.internal_w_cmd.addr[0] |= BIT(7); |
| 632 |
|
| 633 |
c->u.internal_w_cmd.addr[1] = adr; |
| 634 |
c->u.internal_w_cmd.data = cpu_to_be32(data); |
| 635 |
cmd_len = offsetof(struct wilc_spi_cmd, u.internal_w_cmd.crc); |
| 636 |
if (spi_priv->crc7_enabled) |
| 637 |
c->u.internal_w_cmd.crc[0] = wilc_get_crc7(wb, cmd_len); |
| 638 |
} else if (cmd == CMD_SINGLE_WRITE) { |
| 639 |
c->u.w_cmd.addr[0] = adr >> 16; |
| 640 |
c->u.w_cmd.addr[1] = adr >> 8; |
| 641 |
c->u.w_cmd.addr[2] = adr; |
| 642 |
c->u.w_cmd.data = cpu_to_be32(data); |
| 643 |
cmd_len = offsetof(struct wilc_spi_cmd, u.w_cmd.crc); |
| 644 |
if (spi_priv->crc7_enabled) |
| 645 |
c->u.w_cmd.crc[0] = wilc_get_crc7(wb, cmd_len); |
| 646 |
} else { |
| 647 |
dev_err(&spi->dev, "write cmd [%x] not supported\n", cmd); |
| 648 |
return -EINVAL; |
| 649 |
} |
| 650 |
|
| 651 |
if (spi_priv->crc7_enabled) |
| 652 |
cmd_len += 1; |
| 653 |
|
| 654 |
resp_len = sizeof(*r); |
| 655 |
|
| 656 |
if (cmd_len + resp_len > ARRAY_SIZE(wb)) { |
| 657 |
dev_err(&spi->dev, |
| 658 |
"spi buffer size too small (%d) (%d) (%zu)\n", |
| 659 |
cmd_len, resp_len, ARRAY_SIZE(wb)); |
| 660 |
return -EINVAL; |
| 661 |
} |
| 662 |
|
| 663 |
if (wilc_spi_tx_rx(wilc, wb, rb, cmd_len + resp_len)) { |
| 664 |
dev_err(&spi->dev, "Failed cmd write, bus error...\n"); |
| 665 |
return -EINVAL; |
| 666 |
} |
| 667 |
|
| 668 |
r = (struct wilc_spi_rsp_data *)&rb[cmd_len]; |
| 669 |
/* |
| 670 |
* Clockless registers operations might return unexptected responses, |
| 671 |
* even if successful. |
| 672 |
*/ |
| 673 |
if (r->rsp_cmd_type != cmd && !clockless) { |
| 674 |
dev_err(&spi->dev, |
| 675 |
"Failed cmd response, cmd (%02x), resp (%02x)\n", |
| 676 |
cmd, r->rsp_cmd_type); |
| 677 |
return -EINVAL; |
| 678 |
} |
| 679 |
|
| 680 |
if (r->status != WILC_SPI_COMMAND_STAT_SUCCESS && !clockless) { |
| 681 |
dev_err(&spi->dev, "Failed cmd state response state (%02x)\n", |
| 682 |
r->status); |
| 683 |
return -EINVAL; |
| 684 |
} |
| 685 |
|
| 686 |
return 0; |
| 687 |
} |
| 688 |
|
| 689 |
static int wilc_spi_dma_rw(struct wilc *wilc, u8 cmd, u32 adr, u8 *b, u32 sz) |
| 690 |
{ |
| 691 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 692 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 693 |
u16 crc_recv, crc_calc; |
| 694 |
u8 wb[32], rb[32]; |
| 695 |
int cmd_len, resp_len; |
| 696 |
int retry, ix = 0; |
| 697 |
u8 crc[2]; |
| 698 |
struct wilc_spi_cmd *c; |
| 699 |
struct wilc_spi_rsp_data *r; |
| 700 |
|
| 701 |
memset(wb, 0x0, sizeof(wb)); |
| 702 |
memset(rb, 0x0, sizeof(rb)); |
| 703 |
c = (struct wilc_spi_cmd *)wb; |
| 704 |
c->cmd_type = cmd; |
| 705 |
if (cmd == CMD_DMA_WRITE || cmd == CMD_DMA_READ) { |
| 706 |
c->u.dma_cmd.addr[0] = adr >> 16; |
| 707 |
c->u.dma_cmd.addr[1] = adr >> 8; |
| 708 |
c->u.dma_cmd.addr[2] = adr; |
| 709 |
c->u.dma_cmd.size[0] = sz >> 8; |
| 710 |
c->u.dma_cmd.size[1] = sz; |
| 711 |
cmd_len = offsetof(struct wilc_spi_cmd, u.dma_cmd.crc); |
| 712 |
if (spi_priv->crc7_enabled) |
| 713 |
c->u.dma_cmd.crc[0] = wilc_get_crc7(wb, cmd_len); |
| 714 |
} else if (cmd == CMD_DMA_EXT_WRITE || cmd == CMD_DMA_EXT_READ) { |
| 715 |
c->u.dma_cmd_ext.addr[0] = adr >> 16; |
| 716 |
c->u.dma_cmd_ext.addr[1] = adr >> 8; |
| 717 |
c->u.dma_cmd_ext.addr[2] = adr; |
| 718 |
c->u.dma_cmd_ext.size[0] = sz >> 16; |
| 719 |
c->u.dma_cmd_ext.size[1] = sz >> 8; |
| 720 |
c->u.dma_cmd_ext.size[2] = sz; |
| 721 |
cmd_len = offsetof(struct wilc_spi_cmd, u.dma_cmd_ext.crc); |
| 722 |
if (spi_priv->crc7_enabled) |
| 723 |
c->u.dma_cmd_ext.crc[0] = wilc_get_crc7(wb, cmd_len); |
| 724 |
} else { |
| 725 |
dev_err(&spi->dev, "dma read write cmd [%x] not supported\n", |
| 726 |
cmd); |
| 727 |
return -EINVAL; |
| 728 |
} |
| 729 |
if (spi_priv->crc7_enabled) |
| 730 |
cmd_len += 1; |
| 731 |
|
| 732 |
resp_len = sizeof(*r); |
| 733 |
|
| 734 |
if (cmd_len + resp_len > ARRAY_SIZE(wb)) { |
| 735 |
dev_err(&spi->dev, "spi buffer size too small (%d)(%d) (%zu)\n", |
| 736 |
cmd_len, resp_len, ARRAY_SIZE(wb)); |
| 737 |
return -EINVAL; |
| 738 |
} |
| 739 |
|
| 740 |
if (wilc_spi_tx_rx(wilc, wb, rb, cmd_len + resp_len)) { |
| 741 |
dev_err(&spi->dev, "Failed cmd write, bus error...\n"); |
| 742 |
return -EINVAL; |
| 743 |
} |
| 744 |
|
| 745 |
r = (struct wilc_spi_rsp_data *)&rb[cmd_len]; |
| 746 |
if (r->rsp_cmd_type != cmd) { |
| 747 |
dev_err(&spi->dev, |
| 748 |
"Failed cmd response, cmd (%02x), resp (%02x)\n", |
| 749 |
cmd, r->rsp_cmd_type); |
| 750 |
return -EINVAL; |
| 751 |
} |
| 752 |
|
| 753 |
if (r->status != WILC_SPI_COMMAND_STAT_SUCCESS) { |
| 754 |
dev_err(&spi->dev, "Failed cmd state response state (%02x)\n", |
| 755 |
r->status); |
| 756 |
return -EINVAL; |
| 757 |
} |
| 758 |
|
| 759 |
if (cmd == CMD_DMA_WRITE || cmd == CMD_DMA_EXT_WRITE) |
| 760 |
return 0; |
| 761 |
|
| 762 |
while (sz > 0) { |
| 763 |
int nbytes; |
| 764 |
u8 rsp; |
| 765 |
|
| 766 |
nbytes = min_t(u32, sz, DATA_PKT_SZ); |
| 767 |
|
| 768 |
/* |
| 769 |
* Data Response header |
| 770 |
*/ |
| 771 |
retry = 100; |
| 772 |
do { |
| 773 |
if (wilc_spi_rx(wilc, &rsp, 1)) { |
| 774 |
dev_err(&spi->dev, |
| 775 |
"Failed resp read, bus err\n"); |
| 776 |
return -EINVAL; |
| 777 |
} |
| 778 |
if (WILC_GET_RESP_HDR_START(rsp) == 0xf) |
| 779 |
break; |
| 780 |
} while (retry--); |
| 781 |
|
| 782 |
/* |
| 783 |
* Read bytes |
| 784 |
*/ |
| 785 |
if (wilc_spi_rx(wilc, &b[ix], nbytes)) { |
| 786 |
dev_err(&spi->dev, |
| 787 |
"Failed block read, bus err\n"); |
| 788 |
return -EINVAL; |
| 789 |
} |
| 790 |
|
| 791 |
/* |
| 792 |
* Read CRC |
| 793 |
*/ |
| 794 |
if (spi_priv->crc16_enabled) { |
| 795 |
if (wilc_spi_rx(wilc, crc, 2)) { |
| 796 |
dev_err(&spi->dev, |
| 797 |
"Failed block CRC read, bus err\n"); |
| 798 |
return -EINVAL; |
| 799 |
} |
| 800 |
crc_recv = (crc[0] << 8) | crc[1]; |
| 801 |
crc_calc = crc_itu_t(0xffff, &b[ix], nbytes); |
| 802 |
if (crc_recv != crc_calc) { |
| 803 |
dev_err(&spi->dev, "%s: bad CRC 0x%04x " |
| 804 |
"(calculated 0x%04x)\n", __func__, |
| 805 |
crc_recv, crc_calc); |
| 806 |
return -EINVAL; |
| 807 |
} |
| 808 |
} |
| 809 |
|
| 810 |
ix += nbytes; |
| 811 |
sz -= nbytes; |
| 812 |
} |
| 813 |
return 0; |
| 814 |
} |
| 815 |
|
| 816 |
static int wilc_spi_special_cmd(struct wilc *wilc, u8 cmd) |
| 817 |
{ |
| 818 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 819 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 820 |
u8 wb[32], rb[32]; |
| 821 |
int cmd_len, resp_len = 0; |
| 822 |
struct wilc_spi_cmd *c; |
| 823 |
struct wilc_spi_special_cmd_rsp *r; |
| 824 |
|
| 825 |
if (cmd != CMD_TERMINATE && cmd != CMD_REPEAT && cmd != CMD_RESET) |
| 826 |
return -EINVAL; |
| 827 |
|
| 828 |
memset(wb, 0x0, sizeof(wb)); |
| 829 |
memset(rb, 0x0, sizeof(rb)); |
| 830 |
c = (struct wilc_spi_cmd *)wb; |
| 831 |
c->cmd_type = cmd; |
| 832 |
|
| 833 |
if (cmd == CMD_RESET) |
| 834 |
memset(c->u.simple_cmd.addr, 0xFF, 3); |
| 835 |
|
| 836 |
cmd_len = offsetof(struct wilc_spi_cmd, u.simple_cmd.crc); |
| 837 |
resp_len = sizeof(*r); |
| 838 |
|
| 839 |
if (spi_priv->crc7_enabled) { |
| 840 |
c->u.simple_cmd.crc[0] = wilc_get_crc7(wb, cmd_len); |
| 841 |
cmd_len += 1; |
| 842 |
} |
| 843 |
if (cmd_len + resp_len > ARRAY_SIZE(wb)) { |
| 844 |
dev_err(&spi->dev, "spi buffer size too small (%d) (%d) (%zu)\n", |
| 845 |
cmd_len, resp_len, ARRAY_SIZE(wb)); |
| 846 |
return -EINVAL; |
| 847 |
} |
| 848 |
|
| 849 |
if (wilc_spi_tx_rx(wilc, wb, rb, cmd_len + resp_len)) { |
| 850 |
dev_err(&spi->dev, "Failed cmd write, bus error...\n"); |
| 851 |
return -EINVAL; |
| 852 |
} |
| 853 |
|
| 854 |
r = (struct wilc_spi_special_cmd_rsp *)&rb[cmd_len]; |
| 855 |
if (r->rsp_cmd_type != cmd) { |
| 856 |
if (!spi_priv->probing_crc) |
| 857 |
dev_err(&spi->dev, |
| 858 |
"Failed cmd response, cmd (%02x), resp (%02x)\n", |
| 859 |
cmd, r->rsp_cmd_type); |
| 860 |
return -EINVAL; |
| 861 |
} |
| 862 |
|
| 863 |
if (r->status != WILC_SPI_COMMAND_STAT_SUCCESS) { |
| 864 |
dev_err(&spi->dev, "Failed cmd state response state (%02x)\n", |
| 865 |
r->status); |
| 866 |
return -EINVAL; |
| 867 |
} |
| 868 |
return 0; |
| 869 |
} |
| 870 |
|
| 871 |
static void wilc_spi_reset_cmd_sequence(struct wilc *wl, u8 attempt, u32 addr) |
| 872 |
{ |
| 873 |
struct spi_device *spi = to_spi_device(wl->dev); |
| 874 |
struct wilc_spi *spi_priv = wl->bus_data; |
| 875 |
|
| 876 |
if (!spi_priv->probing_crc) |
| 877 |
dev_err(&spi->dev, "Reset and retry %d %x\n", attempt, addr); |
| 878 |
|
| 879 |
usleep_range(1000, 1100); |
| 880 |
wilc_spi_reset(wl); |
| 881 |
usleep_range(1000, 1100); |
| 882 |
} |
| 883 |
|
| 884 |
static int wilc_spi_read_reg(struct wilc *wilc, u32 addr, u32 *data) |
| 885 |
{ |
| 886 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 887 |
int result; |
| 888 |
u8 cmd = CMD_SINGLE_READ; |
| 889 |
u8 clockless = 0; |
| 890 |
u8 i; |
| 891 |
|
| 892 |
if (addr <= WILC_SPI_CLOCKLESS_ADDR_LIMIT) { |
| 893 |
/* Clockless register */ |
| 894 |
cmd = CMD_INTERNAL_READ; |
| 895 |
clockless = 1; |
| 896 |
} |
| 897 |
|
| 898 |
for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { |
| 899 |
result = wilc_spi_single_read(wilc, cmd, addr, data, clockless); |
| 900 |
if (!result) { |
| 901 |
le32_to_cpus(data); |
| 902 |
return 0; |
| 903 |
} |
| 904 |
|
| 905 |
/* retry is not applicable for clockless registers */ |
| 906 |
if (clockless) |
| 907 |
break; |
| 908 |
|
| 909 |
dev_err(&spi->dev, "Failed cmd, read reg (%08x)...\n", addr); |
| 910 |
wilc_spi_reset_cmd_sequence(wilc, i, addr); |
| 911 |
} |
| 912 |
|
| 913 |
return result; |
| 914 |
} |
| 915 |
|
| 916 |
static int wilc_spi_read(struct wilc *wilc, u32 addr, u8 *buf, u32 size) |
| 917 |
{ |
| 918 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 919 |
int result; |
| 920 |
u8 i; |
| 921 |
|
| 922 |
if (size <= 4) |
| 923 |
return -EINVAL; |
| 924 |
|
| 925 |
for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { |
| 926 |
result = wilc_spi_dma_rw(wilc, CMD_DMA_EXT_READ, addr, |
| 927 |
buf, size); |
| 928 |
if (!result) |
| 929 |
return 0; |
| 930 |
|
| 931 |
dev_err(&spi->dev, "Failed cmd, read block (%08x)...\n", addr); |
| 932 |
|
| 933 |
wilc_spi_reset_cmd_sequence(wilc, i, addr); |
| 934 |
} |
| 935 |
|
| 936 |
return result; |
| 937 |
} |
| 938 |
|
| 939 |
static int spi_internal_write(struct wilc *wilc, u32 adr, u32 dat) |
| 940 |
{ |
| 941 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 942 |
int result; |
| 943 |
u8 i; |
| 944 |
|
| 945 |
for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { |
| 946 |
result = wilc_spi_write_cmd(wilc, CMD_INTERNAL_WRITE, adr, |
| 947 |
dat, 0); |
| 948 |
if (!result) |
| 949 |
return 0; |
| 950 |
dev_err(&spi->dev, "Failed internal write cmd...\n"); |
| 951 |
|
| 952 |
wilc_spi_reset_cmd_sequence(wilc, i, adr); |
| 953 |
} |
| 954 |
|
| 955 |
return result; |
| 956 |
} |
| 957 |
|
| 958 |
static int spi_internal_read(struct wilc *wilc, u32 adr, u32 *data) |
| 959 |
{ |
| 960 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 961 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 962 |
int result; |
| 963 |
u8 i; |
| 964 |
|
| 965 |
for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { |
| 966 |
result = wilc_spi_single_read(wilc, CMD_INTERNAL_READ, adr, |
| 967 |
data, 0); |
| 968 |
if (!result) { |
| 969 |
le32_to_cpus(data); |
| 970 |
return 0; |
| 971 |
} |
| 972 |
if (!spi_priv->probing_crc) |
| 973 |
dev_err(&spi->dev, "Failed internal read cmd...\n"); |
| 974 |
|
| 975 |
wilc_spi_reset_cmd_sequence(wilc, i, adr); |
| 976 |
} |
| 977 |
|
| 978 |
return result; |
| 979 |
} |
| 980 |
|
| 981 |
/******************************************** |
| 982 |
* |
| 983 |
* Spi interfaces |
| 984 |
* |
| 985 |
********************************************/ |
| 986 |
|
| 987 |
static int wilc_spi_write_reg(struct wilc *wilc, u32 addr, u32 data) |
| 988 |
{ |
| 989 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 990 |
int result; |
| 991 |
u8 cmd = CMD_SINGLE_WRITE; |
| 992 |
u8 clockless = 0; |
| 993 |
u8 i; |
| 994 |
|
| 995 |
if (addr <= WILC_SPI_CLOCKLESS_ADDR_LIMIT) { |
| 996 |
/* Clockless register */ |
| 997 |
cmd = CMD_INTERNAL_WRITE; |
| 998 |
clockless = 1; |
| 999 |
} |
| 1000 |
|
| 1001 |
for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { |
| 1002 |
result = wilc_spi_write_cmd(wilc, cmd, addr, data, clockless); |
| 1003 |
if (!result) |
| 1004 |
return 0; |
| 1005 |
|
| 1006 |
dev_err(&spi->dev, "Failed cmd, write reg (%08x)...\n", addr); |
| 1007 |
|
| 1008 |
if (clockless) |
| 1009 |
break; |
| 1010 |
|
| 1011 |
wilc_spi_reset_cmd_sequence(wilc, i, addr); |
| 1012 |
} |
| 1013 |
return result; |
| 1014 |
} |
| 1015 |
|
| 1016 |
static int spi_data_rsp(struct wilc *wilc, u8 cmd) |
| 1017 |
{ |
| 1018 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 1019 |
int result, i; |
| 1020 |
u8 rsp[4]; |
| 1021 |
|
| 1022 |
/* |
| 1023 |
* The response to data packets is two bytes long. For |
| 1024 |
* efficiency's sake, wilc_spi_write() wisely ignores the |
| 1025 |
* responses for all packets but the final one. The downside |
| 1026 |
* of that optimization is that when the final data packet is |
| 1027 |
* short, we may receive (part of) the response to the |
| 1028 |
* second-to-last packet before the one for the final packet. |
| 1029 |
* To handle this, we always read 4 bytes and then search for |
| 1030 |
* the last byte that contains the "Response Start" code (0xc |
| 1031 |
* in the top 4 bits). We then know that this byte is the |
| 1032 |
* first response byte of the final data packet. |
| 1033 |
*/ |
| 1034 |
result = wilc_spi_rx(wilc, rsp, sizeof(rsp)); |
| 1035 |
if (result) { |
| 1036 |
dev_err(&spi->dev, "Failed bus error...\n"); |
| 1037 |
return result; |
| 1038 |
} |
| 1039 |
|
| 1040 |
for (i = sizeof(rsp) - 2; i >= 0; --i) |
| 1041 |
if (FIELD_GET(RSP_START_FIELD, rsp[i]) == RSP_START_TAG) |
| 1042 |
break; |
| 1043 |
|
| 1044 |
if (i < 0) { |
| 1045 |
dev_err(&spi->dev, |
| 1046 |
"Data packet response missing (%02x %02x %02x %02x)\n", |
| 1047 |
rsp[0], rsp[1], rsp[2], rsp[3]); |
| 1048 |
return -1; |
| 1049 |
} |
| 1050 |
|
| 1051 |
/* rsp[i] is the last response start byte */ |
| 1052 |
|
| 1053 |
if (FIELD_GET(RSP_TYPE_FIELD, rsp[i]) != RSP_TYPE_LAST_PACKET |
| 1054 |
|| rsp[i + 1] != RSP_STATE_NO_ERROR) { |
| 1055 |
dev_err(&spi->dev, "Data response error (%02x %02x)\n", |
| 1056 |
rsp[i], rsp[i + 1]); |
| 1057 |
return -1; |
| 1058 |
} |
| 1059 |
return 0; |
| 1060 |
} |
| 1061 |
|
| 1062 |
static int wilc_spi_write(struct wilc *wilc, u32 addr, u8 *buf, u32 size) |
| 1063 |
{ |
| 1064 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 1065 |
int result; |
| 1066 |
u8 i; |
| 1067 |
|
| 1068 |
/* |
| 1069 |
* has to be greated than 4 |
| 1070 |
*/ |
| 1071 |
if (size <= 4) |
| 1072 |
return -EINVAL; |
| 1073 |
|
| 1074 |
for (i = 0; i < SPI_RETRY_MAX_LIMIT; i++) { |
| 1075 |
result = wilc_spi_dma_rw(wilc, CMD_DMA_EXT_WRITE, addr, |
| 1076 |
NULL, size); |
| 1077 |
if (result) { |
| 1078 |
dev_err(&spi->dev, |
| 1079 |
"Failed cmd, write block (%08x)...\n", addr); |
| 1080 |
wilc_spi_reset_cmd_sequence(wilc, i, addr); |
| 1081 |
continue; |
| 1082 |
} |
| 1083 |
|
| 1084 |
/* |
| 1085 |
* Data |
| 1086 |
*/ |
| 1087 |
result = spi_data_write(wilc, buf, size); |
| 1088 |
if (result) { |
| 1089 |
dev_err(&spi->dev, "Failed block data write...\n"); |
| 1090 |
wilc_spi_reset_cmd_sequence(wilc, i, addr); |
| 1091 |
continue; |
| 1092 |
} |
| 1093 |
|
| 1094 |
/* |
| 1095 |
* Data response |
| 1096 |
*/ |
| 1097 |
result = spi_data_rsp(wilc, CMD_DMA_EXT_WRITE); |
| 1098 |
if (result) { |
| 1099 |
dev_err(&spi->dev, "Failed block data rsp...\n"); |
| 1100 |
wilc_spi_reset_cmd_sequence(wilc, i, addr); |
| 1101 |
continue; |
| 1102 |
} |
| 1103 |
break; |
| 1104 |
} |
| 1105 |
return result; |
| 1106 |
} |
| 1107 |
|
| 1108 |
/******************************************** |
| 1109 |
* |
| 1110 |
* Bus interfaces |
| 1111 |
* |
| 1112 |
********************************************/ |
| 1113 |
|
| 1114 |
static int wilc_spi_reset(struct wilc *wilc) |
| 1115 |
{ |
| 1116 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 1117 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 1118 |
int result; |
| 1119 |
|
| 1120 |
result = wilc_spi_special_cmd(wilc, CMD_RESET); |
| 1121 |
if (result && !spi_priv->probing_crc) |
| 1122 |
dev_err(&spi->dev, "Failed cmd reset\n"); |
| 1123 |
|
| 1124 |
return result; |
| 1125 |
} |
| 1126 |
|
| 1127 |
static bool wilc_spi_is_init(struct wilc *wilc) |
| 1128 |
{ |
| 1129 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 1130 |
|
| 1131 |
return spi_priv->isinit; |
| 1132 |
} |
| 1133 |
|
| 1134 |
static int wilc_spi_deinit(struct wilc *wilc) |
| 1135 |
{ |
| 1136 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 1137 |
|
| 1138 |
spi_priv->isinit = false; |
| 1139 |
wilc_wlan_power(wilc, false); |
| 1140 |
return 0; |
| 1141 |
} |
| 1142 |
|
| 1143 |
static int wilc_spi_init(struct wilc *wilc, bool resume) |
| 1144 |
{ |
| 1145 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 1146 |
int ret; |
| 1147 |
|
| 1148 |
if (spi_priv->isinit) { |
| 1149 |
/* Confirm we can read chipid register without error: */ |
| 1150 |
if (wilc_validate_chipid(wilc) == 0) |
| 1151 |
return 0; |
| 1152 |
} |
| 1153 |
|
| 1154 |
wilc_wlan_power(wilc, true); |
| 1155 |
|
| 1156 |
ret = wilc_spi_configure_bus_protocol(wilc); |
| 1157 |
if (ret) { |
| 1158 |
wilc_wlan_power(wilc, false); |
| 1159 |
return ret; |
| 1160 |
} |
| 1161 |
|
| 1162 |
spi_priv->isinit = true; |
| 1163 |
|
| 1164 |
return 0; |
| 1165 |
} |
| 1166 |
|
| 1167 |
static int wilc_spi_configure_bus_protocol(struct wilc *wilc) |
| 1168 |
{ |
| 1169 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 1170 |
struct wilc_spi *spi_priv = wilc->bus_data; |
| 1171 |
u32 reg; |
| 1172 |
int ret, i; |
| 1173 |
|
| 1174 |
/* |
| 1175 |
* Infer the CRC settings that are currently in effect. This |
| 1176 |
* is necessary because we can't be sure that the chip has |
| 1177 |
* been RESET (e.g, after module unload and reload). |
| 1178 |
*/ |
| 1179 |
spi_priv->probing_crc = true; |
| 1180 |
spi_priv->crc7_enabled = enable_crc7; |
| 1181 |
spi_priv->crc16_enabled = false; /* don't check CRC16 during probing */ |
| 1182 |
for (i = 0; i < 2; ++i) { |
| 1183 |
ret = spi_internal_read(wilc, WILC_SPI_PROTOCOL_OFFSET, ®); |
| 1184 |
if (ret == 0) |
| 1185 |
break; |
| 1186 |
spi_priv->crc7_enabled = !enable_crc7; |
| 1187 |
} |
| 1188 |
if (ret) { |
| 1189 |
dev_err(&spi->dev, "Failed with CRC7 on and off.\n"); |
| 1190 |
return ret; |
| 1191 |
} |
| 1192 |
|
| 1193 |
/* set up the desired CRC configuration: */ |
| 1194 |
reg &= ~(PROTOCOL_REG_CRC7_MASK | PROTOCOL_REG_CRC16_MASK); |
| 1195 |
if (enable_crc7) |
| 1196 |
reg |= PROTOCOL_REG_CRC7_MASK; |
| 1197 |
if (enable_crc16) |
| 1198 |
reg |= PROTOCOL_REG_CRC16_MASK; |
| 1199 |
|
| 1200 |
/* set up the data packet size: */ |
| 1201 |
BUILD_BUG_ON(DATA_PKT_LOG_SZ < DATA_PKT_LOG_SZ_MIN |
| 1202 |
|| DATA_PKT_LOG_SZ > DATA_PKT_LOG_SZ_MAX); |
| 1203 |
reg &= ~PROTOCOL_REG_PKT_SZ_MASK; |
| 1204 |
reg |= FIELD_PREP(PROTOCOL_REG_PKT_SZ_MASK, |
| 1205 |
DATA_PKT_LOG_SZ - DATA_PKT_LOG_SZ_MIN); |
| 1206 |
|
| 1207 |
/* establish the new setup: */ |
| 1208 |
ret = spi_internal_write(wilc, WILC_SPI_PROTOCOL_OFFSET, reg); |
| 1209 |
if (ret) { |
| 1210 |
dev_err(&spi->dev, |
| 1211 |
"[wilc spi %d]: Failed internal write reg\n", |
| 1212 |
__LINE__); |
| 1213 |
return ret; |
| 1214 |
} |
| 1215 |
/* update our state to match new protocol settings: */ |
| 1216 |
spi_priv->crc7_enabled = enable_crc7; |
| 1217 |
spi_priv->crc16_enabled = enable_crc16; |
| 1218 |
|
| 1219 |
/* re-read to make sure new settings are in effect: */ |
| 1220 |
spi_internal_read(wilc, WILC_SPI_PROTOCOL_OFFSET, ®); |
| 1221 |
|
| 1222 |
spi_priv->probing_crc = false; |
| 1223 |
|
| 1224 |
return 0; |
| 1225 |
} |
| 1226 |
|
| 1227 |
static int wilc_validate_chipid(struct wilc *wilc) |
| 1228 |
{ |
| 1229 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 1230 |
u32 chipid; |
| 1231 |
int ret; |
| 1232 |
|
| 1233 |
/* |
| 1234 |
* make sure can read chip id without protocol error |
| 1235 |
*/ |
| 1236 |
ret = wilc_spi_read_reg(wilc, WILC_CHIPID, &chipid); |
| 1237 |
if (ret) { |
| 1238 |
dev_err(&spi->dev, "Fail cmd read chip id...\n"); |
| 1239 |
return ret; |
| 1240 |
} |
| 1241 |
if (!is_wilc1000(chipid) && !is_wilc3000(chipid)) { |
| 1242 |
dev_err(&spi->dev, "Unknown chip id 0x%x\n", chipid); |
| 1243 |
return -ENODEV; |
| 1244 |
} |
| 1245 |
return 0; |
| 1246 |
} |
| 1247 |
|
| 1248 |
static int wilc_spi_read_size(struct wilc *wilc, u32 *size) |
| 1249 |
{ |
| 1250 |
int ret; |
| 1251 |
|
| 1252 |
ret = spi_internal_read(wilc, |
| 1253 |
WILC_SPI_INT_STATUS - WILC_SPI_REG_BASE, size); |
| 1254 |
*size = FIELD_GET(IRQ_DMA_WD_CNT_MASK, *size); |
| 1255 |
|
| 1256 |
return ret; |
| 1257 |
} |
| 1258 |
|
| 1259 |
static int wilc_spi_read_int(struct wilc *wilc, u32 *int_status) |
| 1260 |
{ |
| 1261 |
return spi_internal_read(wilc, WILC_SPI_INT_STATUS - WILC_SPI_REG_BASE, |
| 1262 |
int_status); |
| 1263 |
} |
| 1264 |
|
| 1265 |
static int wilc_spi_clear_int_ext(struct wilc *wilc, u32 val) |
| 1266 |
{ |
| 1267 |
int ret; |
| 1268 |
int retry = SPI_ENABLE_VMM_RETRY_LIMIT; |
| 1269 |
u32 check; |
| 1270 |
|
| 1271 |
while (retry) { |
| 1272 |
ret = spi_internal_write(wilc, |
| 1273 |
WILC_SPI_INT_CLEAR - WILC_SPI_REG_BASE, |
| 1274 |
val); |
| 1275 |
if (ret) |
| 1276 |
break; |
| 1277 |
|
| 1278 |
ret = spi_internal_read(wilc, |
| 1279 |
WILC_SPI_INT_CLEAR - WILC_SPI_REG_BASE, |
| 1280 |
&check); |
| 1281 |
if (ret || ((check & EN_VMM) == (val & EN_VMM))) |
| 1282 |
break; |
| 1283 |
|
| 1284 |
retry--; |
| 1285 |
} |
| 1286 |
return ret; |
| 1287 |
} |
| 1288 |
|
| 1289 |
static int wilc_spi_sync_ext(struct wilc *wilc, int nint) |
| 1290 |
{ |
| 1291 |
struct spi_device *spi = to_spi_device(wilc->dev); |
| 1292 |
u32 reg; |
| 1293 |
int ret, i; |
| 1294 |
|
| 1295 |
if (nint > MAX_NUM_INT) { |
| 1296 |
dev_err(&spi->dev, "Too many interrupts (%d)...\n", nint); |
| 1297 |
return -EINVAL; |
| 1298 |
} |
| 1299 |
|
| 1300 |
/* |
| 1301 |
* interrupt pin mux select |
| 1302 |
*/ |
| 1303 |
ret = wilc_spi_read_reg(wilc, WILC_PIN_MUX_0, ®); |
| 1304 |
if (ret) { |
| 1305 |
dev_err(&spi->dev, "Failed read reg (%08x)...\n", |
| 1306 |
WILC_PIN_MUX_0); |
| 1307 |
return ret; |
| 1308 |
} |
| 1309 |
reg |= BIT(8); |
| 1310 |
ret = wilc_spi_write_reg(wilc, WILC_PIN_MUX_0, reg); |
| 1311 |
if (ret) { |
| 1312 |
dev_err(&spi->dev, "Failed write reg (%08x)...\n", |
| 1313 |
WILC_PIN_MUX_0); |
| 1314 |
return ret; |
| 1315 |
} |
| 1316 |
|
| 1317 |
/* |
| 1318 |
* interrupt enable |
| 1319 |
*/ |
| 1320 |
ret = wilc_spi_read_reg(wilc, WILC_INTR_ENABLE, ®); |
| 1321 |
if (ret) { |
| 1322 |
dev_err(&spi->dev, "Failed read reg (%08x)...\n", |
| 1323 |
WILC_INTR_ENABLE); |
| 1324 |
return ret; |
| 1325 |
} |
| 1326 |
|
| 1327 |
for (i = 0; (i < 5) && (nint > 0); i++, nint--) |
| 1328 |
reg |= (BIT((27 + i))); |
| 1329 |
|
| 1330 |
ret = wilc_spi_write_reg(wilc, WILC_INTR_ENABLE, reg); |
| 1331 |
if (ret) { |
| 1332 |
dev_err(&spi->dev, "Failed write reg (%08x)...\n", |
| 1333 |
WILC_INTR_ENABLE); |
| 1334 |
return ret; |
| 1335 |
} |
| 1336 |
if (nint) { |
| 1337 |
ret = wilc_spi_read_reg(wilc, WILC_INTR2_ENABLE, ®); |
| 1338 |
if (ret) { |
| 1339 |
dev_err(&spi->dev, "Failed read reg (%08x)...\n", |
| 1340 |
WILC_INTR2_ENABLE); |
| 1341 |
return ret; |
| 1342 |
} |
| 1343 |
|
| 1344 |
for (i = 0; (i < 3) && (nint > 0); i++, nint--) |
| 1345 |
reg |= BIT(i); |
| 1346 |
|
| 1347 |
ret = wilc_spi_write_reg(wilc, WILC_INTR2_ENABLE, reg); |
| 1348 |
if (ret) { |
| 1349 |
dev_err(&spi->dev, "Failed write reg (%08x)...\n", |
| 1350 |
WILC_INTR2_ENABLE); |
| 1351 |
return ret; |
| 1352 |
} |
| 1353 |
} |
| 1354 |
|
| 1355 |
return 0; |
| 1356 |
} |
| 1357 |
|
| 1358 |
/* Global spi HIF function table */ |
| 1359 |
static const struct wilc_hif_func wilc_hif_spi = { |
| 1360 |
.hif_init = wilc_spi_init, |
| 1361 |
.hif_deinit = wilc_spi_deinit, |
| 1362 |
.hif_read_reg = wilc_spi_read_reg, |
| 1363 |
.hif_write_reg = wilc_spi_write_reg, |
| 1364 |
.hif_block_rx = wilc_spi_read, |
| 1365 |
.hif_block_tx = wilc_spi_write, |
| 1366 |
.hif_read_int = wilc_spi_read_int, |
| 1367 |
.hif_clear_int_ext = wilc_spi_clear_int_ext, |
| 1368 |
.hif_read_size = wilc_spi_read_size, |
| 1369 |
.hif_block_tx_ext = wilc_spi_write, |
| 1370 |
.hif_block_rx_ext = wilc_spi_read, |
| 1371 |
.hif_sync_ext = wilc_spi_sync_ext, |
| 1372 |
.hif_reset = wilc_spi_reset, |
| 1373 |
.hif_is_init = wilc_spi_is_init, |
| 1374 |
}; |