| 1 |
/* SPDX-License-Identifier: GPL-2.0-only */ |
| 2 |
/* |
| 3 |
* wanXL serial card driver for Linux |
| 4 |
* definitions common to host driver and card firmware |
| 5 |
* |
| 6 |
* Copyright (C) 2003 Krzysztof Halasa <[email protected]> |
| 7 |
*/ |
| 8 |
|
| 9 |
#define RESET_WHILE_LOADING 0 |
| 10 |
|
| 11 |
/* you must rebuild the firmware if any of the following is changed */ |
| 12 |
#define DETECT_RAM 0 /* needed for > 4MB RAM, 16 MB maximum */ |
| 13 |
#define QUICC_MEMCPY_USES_PLX 1 /* must be used if the host has > 256 MB RAM */ |
| 14 |
|
| 15 |
|
| 16 |
#define STATUS_CABLE_V35 2 |
| 17 |
#define STATUS_CABLE_X21 3 |
| 18 |
#define STATUS_CABLE_V24 4 |
| 19 |
#define STATUS_CABLE_EIA530 5 |
| 20 |
#define STATUS_CABLE_INVALID 6 |
| 21 |
#define STATUS_CABLE_NONE 7 |
| 22 |
|
| 23 |
#define STATUS_CABLE_DCE 0x8000 |
| 24 |
#define STATUS_CABLE_DSR 0x0010 |
| 25 |
#define STATUS_CABLE_DCD 0x0008 |
| 26 |
#define STATUS_CABLE_PM_SHIFT 5 |
| 27 |
|
| 28 |
#define PDM_OFFSET 0x1000 |
| 29 |
|
| 30 |
#define TX_BUFFERS 10 /* per port */ |
| 31 |
#define RX_BUFFERS 30 |
| 32 |
#define RX_QUEUE_LENGTH 40 /* card->host queue length - per card */ |
| 33 |
|
| 34 |
#define PACKET_EMPTY 0x00 |
| 35 |
#define PACKET_FULL 0x10 |
| 36 |
#define PACKET_SENT 0x20 /* TX only */ |
| 37 |
#define PACKET_UNDERRUN 0x30 /* TX only */ |
| 38 |
#define PACKET_PORT_MASK 0x03 /* RX only */ |
| 39 |
|
| 40 |
/* bit numbers in PLX9060 doorbell registers */ |
| 41 |
#define DOORBELL_FROM_CARD_TX_0 0 /* packet sent by the card */ |
| 42 |
#define DOORBELL_FROM_CARD_TX_1 1 |
| 43 |
#define DOORBELL_FROM_CARD_TX_2 2 |
| 44 |
#define DOORBELL_FROM_CARD_TX_3 3 |
| 45 |
#define DOORBELL_FROM_CARD_RX 4 |
| 46 |
#define DOORBELL_FROM_CARD_CABLE_0 5 /* cable/PM/etc. changed */ |
| 47 |
#define DOORBELL_FROM_CARD_CABLE_1 6 |
| 48 |
#define DOORBELL_FROM_CARD_CABLE_2 7 |
| 49 |
#define DOORBELL_FROM_CARD_CABLE_3 8 |
| 50 |
|
| 51 |
#define DOORBELL_TO_CARD_OPEN_0 0 |
| 52 |
#define DOORBELL_TO_CARD_OPEN_1 1 |
| 53 |
#define DOORBELL_TO_CARD_OPEN_2 2 |
| 54 |
#define DOORBELL_TO_CARD_OPEN_3 3 |
| 55 |
#define DOORBELL_TO_CARD_CLOSE_0 4 |
| 56 |
#define DOORBELL_TO_CARD_CLOSE_1 5 |
| 57 |
#define DOORBELL_TO_CARD_CLOSE_2 6 |
| 58 |
#define DOORBELL_TO_CARD_CLOSE_3 7 |
| 59 |
#define DOORBELL_TO_CARD_TX_0 8 /* outbound packet queued */ |
| 60 |
#define DOORBELL_TO_CARD_TX_1 9 |
| 61 |
#define DOORBELL_TO_CARD_TX_2 10 |
| 62 |
#define DOORBELL_TO_CARD_TX_3 11 |
| 63 |
|
| 64 |
/* firmware-only status bits, starting from last DOORBELL_TO_CARD + 1 */ |
| 65 |
#define TASK_SCC_0 12 |
| 66 |
#define TASK_SCC_1 13 |
| 67 |
#define TASK_SCC_2 14 |
| 68 |
#define TASK_SCC_3 15 |
| 69 |
|
| 70 |
#define ALIGN32(x) (((x) + 3) & 0xFFFFFFFC) |
| 71 |
#define BUFFER_LENGTH ALIGN32(HDLC_MAX_MRU + 4) /* 4 bytes for 32-bit CRC */ |
| 72 |
|
| 73 |
/* Address of TX and RX buffers in 68360 address space */ |
| 74 |
#define BUFFERS_ADDR 0x4000 /* 16 KB */ |
| 75 |
|
| 76 |
#ifndef __ASSEMBLER__ |
| 77 |
#define PLX_OFFSET 0 |
| 78 |
#else |
| 79 |
#define PLX_OFFSET PLX + 0x80 |
| 80 |
#endif |
| 81 |
|
| 82 |
#define PLX_MAILBOX_0 (PLX_OFFSET + 0x40) |
| 83 |
#define PLX_MAILBOX_1 (PLX_OFFSET + 0x44) |
| 84 |
#define PLX_MAILBOX_2 (PLX_OFFSET + 0x48) |
| 85 |
#define PLX_MAILBOX_3 (PLX_OFFSET + 0x4C) |
| 86 |
#define PLX_MAILBOX_4 (PLX_OFFSET + 0x50) |
| 87 |
#define PLX_MAILBOX_5 (PLX_OFFSET + 0x54) |
| 88 |
#define PLX_MAILBOX_6 (PLX_OFFSET + 0x58) |
| 89 |
#define PLX_MAILBOX_7 (PLX_OFFSET + 0x5C) |
| 90 |
#define PLX_DOORBELL_TO_CARD (PLX_OFFSET + 0x60) |
| 91 |
#define PLX_DOORBELL_FROM_CARD (PLX_OFFSET + 0x64) |
| 92 |
#define PLX_INTERRUPT_CS (PLX_OFFSET + 0x68) |
| 93 |
#define PLX_CONTROL (PLX_OFFSET + 0x6C) |
| 94 |
|
| 95 |
#ifdef __ASSEMBLER__ |
| 96 |
#define PLX_DMA_0_MODE (PLX + 0x100) |
| 97 |
#define PLX_DMA_0_PCI (PLX + 0x104) |
| 98 |
#define PLX_DMA_0_LOCAL (PLX + 0x108) |
| 99 |
#define PLX_DMA_0_LENGTH (PLX + 0x10C) |
| 100 |
#define PLX_DMA_0_DESC (PLX + 0x110) |
| 101 |
#define PLX_DMA_1_MODE (PLX + 0x114) |
| 102 |
#define PLX_DMA_1_PCI (PLX + 0x118) |
| 103 |
#define PLX_DMA_1_LOCAL (PLX + 0x11C) |
| 104 |
#define PLX_DMA_1_LENGTH (PLX + 0x120) |
| 105 |
#define PLX_DMA_1_DESC (PLX + 0x124) |
| 106 |
#define PLX_DMA_CMD_STS (PLX + 0x128) |
| 107 |
#define PLX_DMA_ARBITR_0 (PLX + 0x12C) |
| 108 |
#define PLX_DMA_ARBITR_1 (PLX + 0x130) |
| 109 |
#endif |
| 110 |
|
| 111 |
#define DESC_LENGTH 12 |
| 112 |
|
| 113 |
/* offsets from start of status_t */ |
| 114 |
/* card to host */ |
| 115 |
#define STATUS_OPEN 0 |
| 116 |
#define STATUS_CABLE (STATUS_OPEN + 4) |
| 117 |
#define STATUS_RX_OVERRUNS (STATUS_CABLE + 4) |
| 118 |
#define STATUS_RX_FRAME_ERRORS (STATUS_RX_OVERRUNS + 4) |
| 119 |
|
| 120 |
/* host to card */ |
| 121 |
#define STATUS_PARITY (STATUS_RX_FRAME_ERRORS + 4) |
| 122 |
#define STATUS_ENCODING (STATUS_PARITY + 4) |
| 123 |
#define STATUS_CLOCKING (STATUS_ENCODING + 4) |
| 124 |
#define STATUS_TX_DESCS (STATUS_CLOCKING + 4) |
| 125 |
|
| 126 |
#ifndef __ASSEMBLER__ |
| 127 |
|
| 128 |
typedef struct { |
| 129 |
volatile u32 stat; |
| 130 |
u32 address; /* PCI address */ |
| 131 |
volatile u32 length; |
| 132 |
}desc_t; |
| 133 |
|
| 134 |
|
| 135 |
typedef struct { |
| 136 |
// Card to host |
| 137 |
volatile u32 open; |
| 138 |
volatile u32 cable; |
| 139 |
volatile u32 rx_overruns; |
| 140 |
volatile u32 rx_frame_errors; |
| 141 |
|
| 142 |
// Host to card |
| 143 |
u32 parity; |
| 144 |
u32 encoding; |
| 145 |
u32 clocking; |
| 146 |
desc_t tx_descs[TX_BUFFERS]; |
| 147 |
}port_status_t; |
| 148 |
|
| 149 |
#endif /* __ASSEMBLER__ */ |