| 1 |
# SPDX-License-Identifier: GPL-2.0-only |
| 2 |
# |
| 3 |
# wan devices configuration |
| 4 |
# |
| 5 |
|
| 6 |
menuconfig WAN |
| 7 |
bool "Wan interfaces support" |
| 8 |
help |
| 9 |
Wide Area Networks (WANs), such as X.25, Frame Relay and leased |
| 10 |
lines, are used to interconnect Local Area Networks (LANs) over vast |
| 11 |
distances with data transfer rates significantly higher than those |
| 12 |
achievable with commonly used asynchronous modem connections. |
| 13 |
|
| 14 |
Usually, a quite expensive external device called a `WAN router' is |
| 15 |
needed to connect to a WAN. As an alternative, a relatively |
| 16 |
inexpensive WAN interface card can allow your Linux box to directly |
| 17 |
connect to a WAN. |
| 18 |
|
| 19 |
If you have one of those cards and wish to use it under Linux, |
| 20 |
say Y here and also to the WAN driver for your card. |
| 21 |
|
| 22 |
If unsure, say N. |
| 23 |
|
| 24 |
if WAN |
| 25 |
|
| 26 |
# Generic HDLC |
| 27 |
config HDLC |
| 28 |
tristate "Generic HDLC layer" |
| 29 |
help |
| 30 |
Say Y to this option if your Linux box contains a WAN (Wide Area |
| 31 |
Network) card supported by this driver and you are planning to |
| 32 |
connect the box to a WAN. |
| 33 |
|
| 34 |
You will need supporting software from |
| 35 |
<http://www.kernel.org/pub/linux/utils/net/hdlc/>. |
| 36 |
Generic HDLC driver currently supports raw HDLC, Cisco HDLC, Frame |
| 37 |
Relay, synchronous Point-to-Point Protocol (PPP) and X.25. |
| 38 |
|
| 39 |
To compile this driver as a module, choose M here: the |
| 40 |
module will be called hdlc. |
| 41 |
|
| 42 |
If unsure, say N. |
| 43 |
|
| 44 |
config HDLC_RAW |
| 45 |
tristate "Raw HDLC support" |
| 46 |
depends on HDLC |
| 47 |
help |
| 48 |
Generic HDLC driver supporting raw HDLC over WAN connections. |
| 49 |
|
| 50 |
If unsure, say N. |
| 51 |
|
| 52 |
config HDLC_RAW_ETH |
| 53 |
tristate "Raw HDLC Ethernet device support" |
| 54 |
depends on HDLC |
| 55 |
help |
| 56 |
Generic HDLC driver supporting raw HDLC Ethernet device emulation |
| 57 |
over WAN connections. |
| 58 |
|
| 59 |
You will need it for Ethernet over HDLC bridges. |
| 60 |
|
| 61 |
If unsure, say N. |
| 62 |
|
| 63 |
config HDLC_CISCO |
| 64 |
tristate "Cisco HDLC support" |
| 65 |
depends on HDLC |
| 66 |
help |
| 67 |
Generic HDLC driver supporting Cisco HDLC over WAN connections. |
| 68 |
|
| 69 |
If unsure, say N. |
| 70 |
|
| 71 |
config HDLC_FR |
| 72 |
tristate "Frame Relay support" |
| 73 |
depends on HDLC |
| 74 |
help |
| 75 |
Generic HDLC driver supporting Frame Relay over WAN connections. |
| 76 |
|
| 77 |
If unsure, say N. |
| 78 |
|
| 79 |
config HDLC_PPP |
| 80 |
tristate "Synchronous Point-to-Point Protocol (PPP) support" |
| 81 |
depends on HDLC |
| 82 |
help |
| 83 |
Generic HDLC driver supporting PPP over WAN connections. |
| 84 |
|
| 85 |
If unsure, say N. |
| 86 |
|
| 87 |
config HDLC_X25 |
| 88 |
tristate "X.25 protocol support" |
| 89 |
depends on HDLC && (LAPB=m && HDLC=m || LAPB=y) |
| 90 |
help |
| 91 |
Generic HDLC driver supporting X.25 over WAN connections. |
| 92 |
|
| 93 |
If unsure, say N. |
| 94 |
|
| 95 |
comment "X.25/LAPB support is disabled" |
| 96 |
depends on HDLC && (LAPB!=m || HDLC!=m) && LAPB!=y |
| 97 |
|
| 98 |
source "drivers/net/wan/framer/Kconfig" |
| 99 |
|
| 100 |
config PCI200SYN |
| 101 |
tristate "Goramo PCI200SYN support" |
| 102 |
depends on HDLC && PCI |
| 103 |
help |
| 104 |
Driver for PCI200SYN cards by Goramo sp. j. |
| 105 |
|
| 106 |
If you have such a card, say Y here and see |
| 107 |
<http://www.kernel.org/pub/linux/utils/net/hdlc/>. |
| 108 |
|
| 109 |
To compile this as a module, choose M here: the |
| 110 |
module will be called pci200syn. |
| 111 |
|
| 112 |
If unsure, say N. |
| 113 |
|
| 114 |
config WANXL |
| 115 |
tristate "SBE Inc. wanXL support" |
| 116 |
depends on HDLC && PCI |
| 117 |
help |
| 118 |
Driver for wanXL PCI cards by SBE Inc. |
| 119 |
|
| 120 |
If you have such a card, say Y here and see |
| 121 |
<http://www.kernel.org/pub/linux/utils/net/hdlc/>. |
| 122 |
|
| 123 |
To compile this as a module, choose M here: the |
| 124 |
module will be called wanxl. |
| 125 |
|
| 126 |
If unsure, say N. |
| 127 |
|
| 128 |
config WANXL_BUILD_FIRMWARE |
| 129 |
bool "rebuild wanXL firmware" |
| 130 |
depends on WANXL && !PREVENT_FIRMWARE_BUILD |
| 131 |
help |
| 132 |
Allows you to rebuild firmware run by the QUICC processor. |
| 133 |
It requires m68k toolchains and hexdump programs. |
| 134 |
|
| 135 |
You should never need this option, say N. |
| 136 |
|
| 137 |
config PC300TOO |
| 138 |
tristate "Cyclades PC300 RSV/X21 alternative support" |
| 139 |
depends on HDLC && PCI |
| 140 |
help |
| 141 |
Alternative driver for PC300 RSV/X21 PCI cards made by |
| 142 |
Cyclades, Inc. If you have such a card, say Y here and see |
| 143 |
<http://www.kernel.org/pub/linux/utils/net/hdlc/>. |
| 144 |
|
| 145 |
To compile this as a module, choose M here: the module |
| 146 |
will be called pc300too. |
| 147 |
|
| 148 |
If unsure, say N here. |
| 149 |
|
| 150 |
config N2 |
| 151 |
tristate "SDL RISCom/N2 support" |
| 152 |
depends on HDLC && ISA |
| 153 |
help |
| 154 |
Driver for RISCom/N2 single or dual channel ISA cards by |
| 155 |
SDL Communications Inc. |
| 156 |
|
| 157 |
If you have such a card, say Y here and see |
| 158 |
<http://www.kernel.org/pub/linux/utils/net/hdlc/>. |
| 159 |
|
| 160 |
Note that N2csu and N2dds cards are not supported by this driver. |
| 161 |
|
| 162 |
To compile this driver as a module, choose M here: the module |
| 163 |
will be called n2. |
| 164 |
|
| 165 |
If unsure, say N. |
| 166 |
|
| 167 |
config C101 |
| 168 |
tristate "Moxa C101 support" |
| 169 |
depends on HDLC && ISA |
| 170 |
help |
| 171 |
Driver for C101 SuperSync ISA cards by Moxa Technologies Co., Ltd. |
| 172 |
|
| 173 |
If you have such a card, say Y here and see |
| 174 |
<http://www.kernel.org/pub/linux/utils/net/hdlc/>. |
| 175 |
|
| 176 |
To compile this driver as a module, choose M here: the |
| 177 |
module will be called c101. |
| 178 |
|
| 179 |
If unsure, say N. |
| 180 |
|
| 181 |
config FARSYNC |
| 182 |
tristate "FarSync T-Series support" |
| 183 |
depends on HDLC && PCI && HAS_IOPORT |
| 184 |
help |
| 185 |
Support for the FarSync T-Series X.21 (and V.35/V.24) cards by |
| 186 |
FarSite Communications Ltd. |
| 187 |
|
| 188 |
Synchronous communication is supported on all ports at speeds up to |
| 189 |
8Mb/s (128K on V.24) using synchronous PPP, Cisco HDLC, raw HDLC, |
| 190 |
Frame Relay or X.25/LAPB. |
| 191 |
|
| 192 |
If you want the module to be automatically loaded when the interface |
| 193 |
is referenced then you should add "alias hdlcX farsync" to a file |
| 194 |
in /etc/modprobe.d/ for each interface, where X is 0, 1, 2, ..., or |
| 195 |
simply use "alias hdlc* farsync" to indicate all of them. |
| 196 |
|
| 197 |
To compile this driver as a module, choose M here: the |
| 198 |
module will be called farsync. |
| 199 |
|
| 200 |
config FSL_QMC_HDLC |
| 201 |
tristate "Freescale QMC HDLC support" |
| 202 |
depends on HDLC |
| 203 |
depends on CPM_QMC |
| 204 |
help |
| 205 |
HDLC support using the Freescale QUICC Multichannel Controller (QMC). |
| 206 |
|
| 207 |
To compile this driver as a module, choose M here: the |
| 208 |
module will be called fsl_qmc_hdlc. |
| 209 |
|
| 210 |
If unsure, say N. |
| 211 |
|
| 212 |
config FSL_UCC_HDLC |
| 213 |
tristate "Freescale QUICC Engine HDLC support" |
| 214 |
depends on HDLC |
| 215 |
depends on QUICC_ENGINE |
| 216 |
help |
| 217 |
Driver for Freescale QUICC Engine HDLC controller. The driver |
| 218 |
supports HDLC in NMSI and TDM mode. |
| 219 |
|
| 220 |
To compile this driver as a module, choose M here: the |
| 221 |
module will be called fsl_ucc_hdlc. |
| 222 |
|
| 223 |
config SLIC_DS26522 |
| 224 |
tristate "Slic Maxim ds26522 card support" |
| 225 |
depends on SPI |
| 226 |
depends on FSL_SOC || ARCH_MXC || ARCH_LAYERSCAPE || COMPILE_TEST |
| 227 |
select BITREVERSE |
| 228 |
help |
| 229 |
This module initializes and configures the slic maxim card |
| 230 |
in T1 or E1 mode. |
| 231 |
|
| 232 |
To compile this driver as a module, choose M here: the |
| 233 |
module will be called slic_ds26522. |
| 234 |
|
| 235 |
config IXP4XX_HSS |
| 236 |
tristate "Intel IXP4xx HSS (synchronous serial port) support" |
| 237 |
depends on HDLC && IXP4XX_NPE && IXP4XX_QMGR |
| 238 |
depends on ARCH_IXP4XX && OF |
| 239 |
select MFD_SYSCON |
| 240 |
help |
| 241 |
Say Y here if you want to use built-in HSS ports |
| 242 |
on IXP4xx processor. |
| 243 |
|
| 244 |
# X.25 network drivers |
| 245 |
config LAPBETHER |
| 246 |
tristate "LAPB over Ethernet driver" |
| 247 |
depends on LAPB && X25 |
| 248 |
help |
| 249 |
Driver for a pseudo device (typically called /dev/lapb0) which allows |
| 250 |
you to open an LAPB point-to-point connection to some other computer |
| 251 |
on your Ethernet network. |
| 252 |
|
| 253 |
In order to do this, you need to say Y or M to the driver for your |
| 254 |
Ethernet card as well as to "LAPB Data Link Driver". |
| 255 |
|
| 256 |
To compile this driver as a module, choose M here: the |
| 257 |
module will be called lapbether. |
| 258 |
|
| 259 |
|
| 260 |
If unsure, say N. |
| 261 |
|
| 262 |
endif # WAN |