| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Device tree for LEGO MINDSTORMS EV3 |
| 4 |
* |
| 5 |
* Copyright (C) 2017 David Lechner <[email protected]> |
| 6 |
*/ |
| 7 |
|
| 8 |
/dts-v1/; |
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/input/linux-event-codes.h> |
| 11 |
#include <dt-bindings/pwm/pwm.h> |
| 12 |
|
| 13 |
#include "da850.dtsi" |
| 14 |
|
| 15 |
/ { |
| 16 |
compatible = "lego,ev3", "ti,da850"; |
| 17 |
model = "LEGO MINDSTORMS EV3"; |
| 18 |
|
| 19 |
aliases { |
| 20 |
serial1 = &serial1; |
| 21 |
}; |
| 22 |
|
| 23 |
memory@c0000000 { |
| 24 |
device_type = "memory"; |
| 25 |
reg = <0xc0000000 0x04000000>; |
| 26 |
}; |
| 27 |
|
| 28 |
/* |
| 29 |
* The buttons on the EV3 are mapped to keyboard keys. |
| 30 |
*/ |
| 31 |
gpio_keys { |
| 32 |
compatible = "gpio-keys"; |
| 33 |
label = "EV3 Brick Buttons"; |
| 34 |
pinctrl-names = "default"; |
| 35 |
pinctrl-0 = <&button_bias>; |
| 36 |
|
| 37 |
center { |
| 38 |
label = "Center"; |
| 39 |
linux,code = <KEY_ENTER>; |
| 40 |
gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; |
| 41 |
}; |
| 42 |
|
| 43 |
left { |
| 44 |
label = "Left"; |
| 45 |
linux,code = <KEY_LEFT>; |
| 46 |
gpios = <&gpio 102 GPIO_ACTIVE_HIGH>; |
| 47 |
}; |
| 48 |
|
| 49 |
back { |
| 50 |
label = "Back"; |
| 51 |
linux,code = <KEY_BACKSPACE>; |
| 52 |
gpios = <&gpio 106 GPIO_ACTIVE_HIGH>; |
| 53 |
}; |
| 54 |
|
| 55 |
right { |
| 56 |
label = "Right"; |
| 57 |
linux,code = <KEY_RIGHT>; |
| 58 |
gpios = <&gpio 124 GPIO_ACTIVE_HIGH>; |
| 59 |
}; |
| 60 |
|
| 61 |
down { |
| 62 |
label = "Down"; |
| 63 |
linux,code = <KEY_DOWN>; |
| 64 |
gpios = <&gpio 126 GPIO_ACTIVE_HIGH>; |
| 65 |
}; |
| 66 |
|
| 67 |
up { |
| 68 |
label = "Up"; |
| 69 |
linux,code = <KEY_UP>; |
| 70 |
gpios = <&gpio 127 GPIO_ACTIVE_HIGH>; |
| 71 |
}; |
| 72 |
}; |
| 73 |
|
| 74 |
/* |
| 75 |
* The EV3 has two built-in bi-color LEDs behind the buttons. |
| 76 |
*/ |
| 77 |
leds { |
| 78 |
compatible = "gpio-leds"; |
| 79 |
|
| 80 |
left_green { |
| 81 |
label = "led0:green:brick-status"; |
| 82 |
/* GP6[13] */ |
| 83 |
gpios = <&gpio 103 GPIO_ACTIVE_HIGH>; |
| 84 |
linux,default-trigger = "default-on"; |
| 85 |
}; |
| 86 |
|
| 87 |
right_red { |
| 88 |
label = "led1:red:brick-status"; |
| 89 |
/* GP6[7] */ |
| 90 |
gpios = <&gpio 108 GPIO_ACTIVE_HIGH>; |
| 91 |
linux,default-trigger = "default-on"; |
| 92 |
}; |
| 93 |
|
| 94 |
left_red { |
| 95 |
label = "led0:red:brick-status"; |
| 96 |
/* GP6[12] */ |
| 97 |
gpios = <&gpio 109 GPIO_ACTIVE_HIGH>; |
| 98 |
linux,default-trigger = "default-on"; |
| 99 |
}; |
| 100 |
|
| 101 |
right_green { |
| 102 |
label = "led1:green:brick-status"; |
| 103 |
/* GP6[14] */ |
| 104 |
gpios = <&gpio 110 GPIO_ACTIVE_HIGH>; |
| 105 |
linux,default-trigger = "default-on"; |
| 106 |
}; |
| 107 |
}; |
| 108 |
|
| 109 |
/* |
| 110 |
* The EV3 is powered down by turning off the main 5V supply. |
| 111 |
*/ |
| 112 |
gpio-poweroff { |
| 113 |
compatible = "gpio-poweroff"; |
| 114 |
gpios = <&gpio 107 GPIO_ACTIVE_LOW>; |
| 115 |
}; |
| 116 |
|
| 117 |
sound { |
| 118 |
compatible = "pwm-beeper"; |
| 119 |
pinctrl-names = "default"; |
| 120 |
pinctrl-0 = <&ehrpwm0b_pins>; |
| 121 |
pwms = <&ehrpwm0 1 1000000 0>; |
| 122 |
amp-supply = <&>; |
| 123 |
}; |
| 124 |
|
| 125 |
cvdd: regulator0 { |
| 126 |
compatible = "regulator-fixed"; |
| 127 |
regulator-name = "cvdd"; |
| 128 |
regulator-min-microvolt = <1200000>; |
| 129 |
regulator-max-microvolt = <1200000>; |
| 130 |
regulator-always-on; |
| 131 |
regulator-boot-on; |
| 132 |
}; |
| 133 |
|
| 134 |
/* |
| 135 |
* This is a 5V current limiting regulator that is shared by USB, |
| 136 |
* the sensor (input) ports, the motor (output) ports and the A/DC. |
| 137 |
*/ |
| 138 |
vcc5v: regulator1 { |
| 139 |
compatible = "regulator-fixed"; |
| 140 |
regulator-name = "vcc5v"; |
| 141 |
regulator-min-microvolt = <5000000>; |
| 142 |
regulator-max-microvolt = <5000000>; |
| 143 |
gpio = <&gpio 101 0>; |
| 144 |
over-current-gpios = <&gpio 99 GPIO_ACTIVE_LOW>; |
| 145 |
enable-active-high; |
| 146 |
regulator-boot-on; |
| 147 |
}; |
| 148 |
|
| 149 |
/* |
| 150 |
* This is a simple voltage divider on VCC5V to provide a 2.5V |
| 151 |
* reference signal to the ADC. |
| 152 |
*/ |
| 153 |
adc_ref: regulator2 { |
| 154 |
compatible = "regulator-fixed"; |
| 155 |
regulator-name = "adc ref"; |
| 156 |
regulator-min-microvolt = <2500000>; |
| 157 |
regulator-max-microvolt = <2500000>; |
| 158 |
regulator-boot-on; |
| 159 |
vin-supply = <&vcc5v>; |
| 160 |
}; |
| 161 |
|
| 162 |
/* |
| 163 |
* This is the amplifier for the speaker. |
| 164 |
*/ |
| 165 |
amp: regulator3 { |
| 166 |
compatible = "regulator-fixed"; |
| 167 |
regulator-name = "amp"; |
| 168 |
gpio = <&gpio 111 GPIO_ACTIVE_HIGH>; |
| 169 |
enable-active-high; |
| 170 |
}; |
| 171 |
|
| 172 |
/* |
| 173 |
* The EV3 can use 6-AA batteries or a rechargeable Li-ion battery pack. |
| 174 |
*/ |
| 175 |
battery { |
| 176 |
compatible = "lego,ev3-battery"; |
| 177 |
io-channels = <&adc 4>, <&adc 3>; |
| 178 |
io-channel-names = "voltage", "current"; |
| 179 |
rechargeable-gpios = <&gpio 136 GPIO_ACTIVE_LOW>; |
| 180 |
}; |
| 181 |
|
| 182 |
bt_slow_clk: bt-clock { |
| 183 |
pinctrl-names = "default"; |
| 184 |
pinctrl-0 = <&ecap2_pins>, <&bt_clock_bias>; |
| 185 |
compatible = "pwm-clock"; |
| 186 |
#clock-cells = <0>; |
| 187 |
clock-frequency = <32768>; |
| 188 |
pwms = <&ecap2 0 30518 0>; |
| 189 |
}; |
| 190 |
|
| 191 |
/* ARM local RAM */ |
| 192 |
memory@ffff0000 { |
| 193 |
compatible = "syscon", "simple-mfd"; |
| 194 |
reg = <0xffff0000 0x2000>; /* 8k */ |
| 195 |
|
| 196 |
/* |
| 197 |
* The I2C bootloader looks for this magic value to either |
| 198 |
* boot normally or boot into a firmware update mode. |
| 199 |
*/ |
| 200 |
reboot-mode { |
| 201 |
compatible = "syscon-reboot-mode"; |
| 202 |
offset = <0x1ffc>; |
| 203 |
mode-normal = <0x00000000>; |
| 204 |
mode-loader = <0x5555aaaa>; |
| 205 |
}; |
| 206 |
}; |
| 207 |
}; |
| 208 |
|
| 209 |
&ref_clk { |
| 210 |
clock-frequency = <24000000>; |
| 211 |
}; |
| 212 |
|
| 213 |
&cpu { |
| 214 |
cpu-supply = <&cvdd>; |
| 215 |
}; |
| 216 |
|
| 217 |
/* since we have a fixed regulator, we can't run at these points */ |
| 218 |
&opp_100 { |
| 219 |
status = "disabled"; |
| 220 |
}; |
| 221 |
|
| 222 |
&opp_200 { |
| 223 |
status = "disabled"; |
| 224 |
}; |
| 225 |
|
| 226 |
/* |
| 227 |
* The SoC is actually the 456MHz version, but because of the fixed regulator |
| 228 |
* This is the fastest we can go. |
| 229 |
*/ |
| 230 |
&opp_375 { |
| 231 |
status = "okay"; |
| 232 |
}; |
| 233 |
|
| 234 |
&pmx_core { |
| 235 |
status = "okay"; |
| 236 |
|
| 237 |
ev3_lcd_pins: lcd-pins { |
| 238 |
pinctrl-single,bits = < |
| 239 |
/* SIMO, CLK */ |
| 240 |
0x14 0x00100100 0x00f00f00 |
| 241 |
>; |
| 242 |
}; |
| 243 |
}; |
| 244 |
|
| 245 |
&pinconf { |
| 246 |
status = "okay"; |
| 247 |
|
| 248 |
/* Buttons have external pulldown resistors */ |
| 249 |
button_bias: button-bias-groups { |
| 250 |
disable { |
| 251 |
groups = "cp5", "cp24", "cp25", "cp28"; |
| 252 |
bias-disable; |
| 253 |
}; |
| 254 |
}; |
| 255 |
|
| 256 |
bt_clock_bias: bt-clock-bias-groups { |
| 257 |
disable { |
| 258 |
groups = "cp2"; |
| 259 |
bias-disable; |
| 260 |
}; |
| 261 |
}; |
| 262 |
|
| 263 |
bt_pic_bias: bt-pic-bias-groups { |
| 264 |
disable { |
| 265 |
groups = "cp20"; |
| 266 |
bias-disable; |
| 267 |
}; |
| 268 |
}; |
| 269 |
}; |
| 270 |
|
| 271 |
/* Input port 1 */ |
| 272 |
&serial1 { |
| 273 |
status = "okay"; |
| 274 |
pinctrl-names = "default"; |
| 275 |
pinctrl-0 = <&serial1_rxtx_pins>; |
| 276 |
}; |
| 277 |
|
| 278 |
&serial2 { |
| 279 |
pinctrl-names = "default"; |
| 280 |
pinctrl-0 = <&serial2_rxtx_pins>, <&serial2_rtscts_pins>, <&bt_pic_bias>; |
| 281 |
status = "okay"; |
| 282 |
|
| 283 |
bluetooth { |
| 284 |
compatible = "ti,cc2560"; |
| 285 |
clocks = <&bt_slow_clk>; |
| 286 |
clock-names = "ext_clock"; |
| 287 |
enable-gpios = <&gpio 73 GPIO_ACTIVE_HIGH>; |
| 288 |
max-speed = <2000000>; |
| 289 |
nvmem-cells = <&bdaddr>; |
| 290 |
nvmem-cell-names = "bd-address"; |
| 291 |
}; |
| 292 |
}; |
| 293 |
|
| 294 |
&rtc0 { |
| 295 |
status = "okay"; |
| 296 |
}; |
| 297 |
|
| 298 |
&i2c0 { |
| 299 |
status = "okay"; |
| 300 |
clock-frequency = <400000>; |
| 301 |
pinctrl-names = "default"; |
| 302 |
pinctrl-0 = <&i2c0_pins>; |
| 303 |
|
| 304 |
/* |
| 305 |
* EEPROM contains the first stage bootloader, HW ID and Bluetooth MAC. |
| 306 |
*/ |
| 307 |
eeprom@50 { |
| 308 |
compatible = "microchip,24c128", "atmel,24c128"; |
| 309 |
pagesize = <64>; |
| 310 |
read-only; |
| 311 |
reg = <0x50>; |
| 312 |
#address-cells = <1>; |
| 313 |
#size-cells = <1>; |
| 314 |
|
| 315 |
bdaddr: bdaddr@3f06 { |
| 316 |
reg = <0x3f06 0x06>; |
| 317 |
}; |
| 318 |
}; |
| 319 |
}; |
| 320 |
|
| 321 |
&wdt { |
| 322 |
status = "okay"; |
| 323 |
}; |
| 324 |
|
| 325 |
&mmc0 { |
| 326 |
status = "okay"; |
| 327 |
max-frequency = <50000000>; |
| 328 |
bus-width = <4>; |
| 329 |
cd-gpios = <&gpio 94 GPIO_ACTIVE_LOW>; |
| 330 |
pinctrl-names = "default"; |
| 331 |
pinctrl-0 = <&mmc0_pins>; |
| 332 |
}; |
| 333 |
|
| 334 |
&spi0 { |
| 335 |
status = "okay"; |
| 336 |
pinctrl-names = "default"; |
| 337 |
pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>, <&spi0_cs3_pin>; |
| 338 |
|
| 339 |
flash@0 { |
| 340 |
compatible = "n25q128a13", "jedec,spi-nor"; |
| 341 |
reg = <0>; |
| 342 |
spi-max-frequency = <50000000>; |
| 343 |
ti,spi-wdelay = <8>; |
| 344 |
|
| 345 |
/* Partitions are based on the official firmware from LEGO */ |
| 346 |
partitions { |
| 347 |
compatible = "fixed-partitions"; |
| 348 |
#address-cells = <1>; |
| 349 |
#size-cells = <1>; |
| 350 |
|
| 351 |
partition@0 { |
| 352 |
label = "U-Boot"; |
| 353 |
reg = <0 0x40000>; |
| 354 |
}; |
| 355 |
|
| 356 |
partition@40000 { |
| 357 |
label = "U-Boot Env"; |
| 358 |
reg = <0x40000 0x10000>; |
| 359 |
}; |
| 360 |
|
| 361 |
partition@50000 { |
| 362 |
label = "Kernel"; |
| 363 |
reg = <0x50000 0x200000>; |
| 364 |
}; |
| 365 |
|
| 366 |
partition@250000 { |
| 367 |
label = "Filesystem"; |
| 368 |
reg = <0x250000 0xa50000>; |
| 369 |
}; |
| 370 |
|
| 371 |
partition@cb0000 { |
| 372 |
label = "Storage"; |
| 373 |
reg = <0xcb0000 0x2f0000>; |
| 374 |
}; |
| 375 |
}; |
| 376 |
}; |
| 377 |
|
| 378 |
adc: adc@3 { |
| 379 |
compatible = "ti,ads7957"; |
| 380 |
reg = <3>; |
| 381 |
#io-channel-cells = <1>; |
| 382 |
spi-max-frequency = <1000000>; |
| 383 |
ti,spi-wdelay = <63>; |
| 384 |
vref-supply = <&adc_ref>; |
| 385 |
}; |
| 386 |
}; |
| 387 |
|
| 388 |
&spi1 { |
| 389 |
status = "okay"; |
| 390 |
pinctrl-0 = <&ev3_lcd_pins>; |
| 391 |
pinctrl-names = "default"; |
| 392 |
cs-gpios = <&gpio 44 GPIO_ACTIVE_LOW>; |
| 393 |
|
| 394 |
display@0 { |
| 395 |
compatible = "lego,ev3-lcd"; |
| 396 |
reg = <0>; |
| 397 |
spi-max-frequency = <10000000>; |
| 398 |
a0-gpios = <&gpio 43 GPIO_ACTIVE_HIGH>; |
| 399 |
reset-gpios = <&gpio 80 GPIO_ACTIVE_HIGH>; |
| 400 |
}; |
| 401 |
}; |
| 402 |
|
| 403 |
&ecap2 { |
| 404 |
status = "okay"; |
| 405 |
}; |
| 406 |
|
| 407 |
&ehrpwm0 { |
| 408 |
status = "okay"; |
| 409 |
}; |
| 410 |
|
| 411 |
&gpio { |
| 412 |
status = "okay"; |
| 413 |
|
| 414 |
/* Don't pull down battery voltage adc io channel */ |
| 415 |
batt-volt-en-hog { |
| 416 |
gpio-hog; |
| 417 |
gpios = <6 GPIO_ACTIVE_HIGH>; |
| 418 |
output-high; |
| 419 |
}; |
| 420 |
|
| 421 |
/* Don't impede Bluetooth clock signal */ |
| 422 |
bt-clock-en-hog { |
| 423 |
gpio-hog; |
| 424 |
gpios = <5 GPIO_ACTIVE_HIGH>; |
| 425 |
input; |
| 426 |
}; |
| 427 |
|
| 428 |
/* |
| 429 |
* There is a PIC microcontroller for interfacing with an Apple MFi |
| 430 |
* chip. This interferes with normal Bluetooth operation, so we need |
| 431 |
* to make sure it is turned off. Note: The publicly available |
| 432 |
* schematics from LEGO don't show that these pins are connected to |
| 433 |
* anything, but they are present in the source code from LEGO. |
| 434 |
*/ |
| 435 |
|
| 436 |
bt-pic-en-hog { |
| 437 |
gpio-hog; |
| 438 |
gpios = <51 GPIO_ACTIVE_HIGH>; |
| 439 |
output-low; |
| 440 |
}; |
| 441 |
|
| 442 |
bt-pic-rst-hog { |
| 443 |
gpio-hog; |
| 444 |
gpios = <78 GPIO_ACTIVE_HIGH>; |
| 445 |
output-high; |
| 446 |
}; |
| 447 |
|
| 448 |
bt-pic-cts-hog { |
| 449 |
gpio-hog; |
| 450 |
gpios = <87 GPIO_ACTIVE_HIGH>; |
| 451 |
input; |
| 452 |
}; |
| 453 |
}; |
| 454 |
|
| 455 |
&usb_phy { |
| 456 |
status = "okay"; |
| 457 |
}; |
| 458 |
|
| 459 |
&usb0 { |
| 460 |
status = "okay"; |
| 461 |
}; |
| 462 |
|
| 463 |
&usb1 { |
| 464 |
status = "okay"; |
| 465 |
vbus-supply = <&vcc5v>; |
| 466 |
}; |