| 1 |
// SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| 2 |
/* |
| 3 |
* Copyright 2018 Alexander Monakov <[email protected]> |
| 4 |
*/ |
| 5 |
/dts-v1/; |
| 6 |
|
| 7 |
#include "berlin2cd.dtsi" |
| 8 |
#include <dt-bindings/gpio/gpio.h> |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "Valve Steam Link"; |
| 12 |
compatible = "valve,steamlink", "marvell,berlin2cd", "marvell,berlin"; |
| 13 |
|
| 14 |
memory@0 { |
| 15 |
device_type = "memory"; |
| 16 |
reg = <0x00000000 0x20000000>; /* 512 MB */ |
| 17 |
}; |
| 18 |
|
| 19 |
gpio-restart { |
| 20 |
compatible = "gpio-restart"; |
| 21 |
gpios = <&porta 6 GPIO_ACTIVE_HIGH>; |
| 22 |
active-delay = <100>; |
| 23 |
inactive-delay = <10>; |
| 24 |
wait-delay = <100>; |
| 25 |
priority = <200>; |
| 26 |
}; |
| 27 |
}; |
| 28 |
|
| 29 |
&cpu { |
| 30 |
cpu-supply = <&vcpu>; |
| 31 |
operating-points = < |
| 32 |
/* kHz uV */ |
| 33 |
1000000 1325000 |
| 34 |
>; |
| 35 |
}; |
| 36 |
|
| 37 |
&i2c0 { |
| 38 |
status = "okay"; |
| 39 |
|
| 40 |
/* There are two regulators on the board. One is accessible via I2C, |
| 41 |
* with buck1 providing SoC power (set up by bootloader to 1.325V or |
| 42 |
* less depending on leakage value in OTP), and buck2 likely used for |
| 43 |
* DRAM (providing 1.35V). The other regulator on the opposite side |
| 44 |
* of the board is probably supplying SDIO and NAND fixed voltages. */ |
| 45 |
regulator@19 { |
| 46 |
compatible = "marvell,88pg868"; |
| 47 |
reg = <0x19>; |
| 48 |
|
| 49 |
vcpu: buck1 { |
| 50 |
regulator-boot-on; |
| 51 |
regulator-always-on; |
| 52 |
regulator-min-microvolt = <1000000>; |
| 53 |
regulator-max-microvolt = <1325000>; |
| 54 |
}; |
| 55 |
}; |
| 56 |
}; |
| 57 |
|
| 58 |
/* Fixed interface to on-board Marvell 8897 Wi-Fi/Bluetooth/NFC chip. */ |
| 59 |
&sdhci0 { |
| 60 |
keep-power-in-suspend; |
| 61 |
non-removable; |
| 62 |
status = "okay"; |
| 63 |
}; |
| 64 |
|
| 65 |
&uart0 { |
| 66 |
/* RX/TX are routed to TP50/TP51 on the board. */ |
| 67 |
status = "okay"; |
| 68 |
}; |
| 69 |
|
| 70 |
/* The SoC is connected to on-board USB hub that in turn has one downstream |
| 71 |
* port wired to the on-board Steam Controller wireless receiver chip. */ |
| 72 |
&usb_phy1 { status = "okay"; }; |
| 73 |
|
| 74 |
&usb1 { |
| 75 |
dr_mode = "host"; |
| 76 |
status = "okay"; |
| 77 |
}; |
| 78 |
|
| 79 |
ð1 { status = "okay"; }; |