| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* PHYTEC phyCORE-LPC3250 board |
| 4 |
* |
| 5 |
* Copyright (C) 2015-2019 Vladimir Zapolskiy <[email protected]> |
| 6 |
* Copyright 2012 Roland Stigge <[email protected]> |
| 7 |
*/ |
| 8 |
|
| 9 |
/dts-v1/; |
| 10 |
#include "lpc32xx.dtsi" |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250"; |
| 14 |
compatible = "phytec,phy3250", "nxp,lpc3250"; |
| 15 |
|
| 16 |
memory@80000000 { |
| 17 |
device_type = "memory"; |
| 18 |
reg = <0x80000000 0x4000000>; |
| 19 |
}; |
| 20 |
|
| 21 |
leds { |
| 22 |
compatible = "gpio-leds"; |
| 23 |
|
| 24 |
led0 { /* red */ |
| 25 |
gpios = <&gpio 5 1 0>; /* GPO_P3 1, GPIO 80, active high */ |
| 26 |
default-state = "off"; |
| 27 |
}; |
| 28 |
|
| 29 |
led1 { /* green */ |
| 30 |
gpios = <&gpio 5 14 0>; /* GPO_P3 14, GPIO 93, active high */ |
| 31 |
linux,default-trigger = "heartbeat"; |
| 32 |
}; |
| 33 |
}; |
| 34 |
|
| 35 |
panel: panel { |
| 36 |
compatible = "sharp,lq035q7db03"; |
| 37 |
power-supply = <®_lcd>; |
| 38 |
|
| 39 |
port { |
| 40 |
panel_input: endpoint { |
| 41 |
remote-endpoint = <&cldc_output>; |
| 42 |
}; |
| 43 |
}; |
| 44 |
}; |
| 45 |
|
| 46 |
reg_backlight: regulator-backlight { |
| 47 |
compatible = "regulator-fixed"; |
| 48 |
regulator-name = "backlight"; |
| 49 |
regulator-min-microvolt = <1800000>; |
| 50 |
regulator-max-microvolt = <1800000>; |
| 51 |
gpio = <&gpio 5 4 0>; |
| 52 |
enable-active-high; |
| 53 |
regulator-boot-on; |
| 54 |
}; |
| 55 |
|
| 56 |
reg_lcd: regulator-lcd { |
| 57 |
compatible = "regulator-fixed"; |
| 58 |
regulator-name = "lcd"; |
| 59 |
regulator-min-microvolt = <1800000>; |
| 60 |
regulator-max-microvolt = <1800000>; |
| 61 |
gpio = <&gpio 5 0 0>; |
| 62 |
enable-active-high; |
| 63 |
regulator-boot-on; |
| 64 |
}; |
| 65 |
|
| 66 |
reg_sd: regulator-sd { |
| 67 |
compatible = "regulator-fixed"; |
| 68 |
regulator-name = "sd"; |
| 69 |
regulator-min-microvolt = <3300000>; |
| 70 |
regulator-max-microvolt = <3300000>; |
| 71 |
gpio = <&gpio 5 5 0>; |
| 72 |
enable-active-high; |
| 73 |
regulator-boot-on; |
| 74 |
}; |
| 75 |
}; |
| 76 |
|
| 77 |
&clcd { |
| 78 |
max-memory-bandwidth = <18710000>; |
| 79 |
status = "okay"; |
| 80 |
|
| 81 |
port { |
| 82 |
cldc_output: endpoint { |
| 83 |
remote-endpoint = <&panel_input>; |
| 84 |
arm,pl11x,tft-r0g0b0-pads = <0 8 16>; |
| 85 |
}; |
| 86 |
}; |
| 87 |
}; |
| 88 |
|
| 89 |
&i2c1 { |
| 90 |
clock-frequency = <100000>; |
| 91 |
|
| 92 |
uda1380: uda1380@18 { |
| 93 |
compatible = "nxp,uda1380"; |
| 94 |
reg = <0x18>; |
| 95 |
power-gpio = <&gpio 3 10 0>; |
| 96 |
reset-gpio = <&gpio 3 2 0>; |
| 97 |
dac-clk = "wspll"; |
| 98 |
}; |
| 99 |
|
| 100 |
pcf8563: rtc@51 { |
| 101 |
compatible = "nxp,pcf8563"; |
| 102 |
reg = <0x51>; |
| 103 |
}; |
| 104 |
}; |
| 105 |
|
| 106 |
&i2c2 { |
| 107 |
clock-frequency = <100000>; |
| 108 |
}; |
| 109 |
|
| 110 |
&i2cusb { |
| 111 |
clock-frequency = <100000>; |
| 112 |
|
| 113 |
isp1301: usb-transceiver@2c { |
| 114 |
compatible = "nxp,isp1301"; |
| 115 |
reg = <0x2c>; |
| 116 |
}; |
| 117 |
}; |
| 118 |
|
| 119 |
&key { |
| 120 |
keypad,num-rows = <1>; |
| 121 |
keypad,num-columns = <1>; |
| 122 |
nxp,debounce-delay-ms = <3>; |
| 123 |
nxp,scan-delay-ms = <34>; |
| 124 |
linux,keymap = <0x00000002>; |
| 125 |
status = "okay"; |
| 126 |
}; |
| 127 |
|
| 128 |
&mac { |
| 129 |
phy-mode = "rmii"; |
| 130 |
use-iram; |
| 131 |
status = "okay"; |
| 132 |
}; |
| 133 |
|
| 134 |
/* Here, choose exactly one from: ohci, usbd */ |
| 135 |
&ohci /* &usbd */ { |
| 136 |
transceiver = <&isp1301>; |
| 137 |
status = "okay"; |
| 138 |
}; |
| 139 |
|
| 140 |
&sd { |
| 141 |
wp-gpios = <&gpio 3 0 0>; |
| 142 |
cd-gpios = <&gpio 3 1 0>; |
| 143 |
cd-inverted; |
| 144 |
bus-width = <4>; |
| 145 |
vmmc-supply = <®_sd>; |
| 146 |
status = "okay"; |
| 147 |
}; |
| 148 |
|
| 149 |
/* 64MB Flash via SLC NAND controller */ |
| 150 |
&slc { |
| 151 |
status = "okay"; |
| 152 |
|
| 153 |
nxp,wdr-clks = <14>; |
| 154 |
nxp,wwidth = <40000000>; |
| 155 |
nxp,whold = <100000000>; |
| 156 |
nxp,wsetup = <100000000>; |
| 157 |
nxp,rdr-clks = <14>; |
| 158 |
nxp,rwidth = <40000000>; |
| 159 |
nxp,rhold = <66666666>; |
| 160 |
nxp,rsetup = <100000000>; |
| 161 |
nand-on-flash-bbt; |
| 162 |
gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ |
| 163 |
|
| 164 |
partitions { |
| 165 |
compatible = "fixed-partitions"; |
| 166 |
#address-cells = <1>; |
| 167 |
#size-cells = <1>; |
| 168 |
|
| 169 |
mtd0@0 { |
| 170 |
label = "phy3250-boot"; |
| 171 |
reg = <0x00000000 0x00064000>; |
| 172 |
read-only; |
| 173 |
}; |
| 174 |
|
| 175 |
mtd1@64000 { |
| 176 |
label = "phy3250-uboot"; |
| 177 |
reg = <0x00064000 0x00190000>; |
| 178 |
read-only; |
| 179 |
}; |
| 180 |
|
| 181 |
mtd2@1f4000 { |
| 182 |
label = "phy3250-ubt-prms"; |
| 183 |
reg = <0x001f4000 0x00010000>; |
| 184 |
}; |
| 185 |
|
| 186 |
mtd3@204000 { |
| 187 |
label = "phy3250-kernel"; |
| 188 |
reg = <0x00204000 0x00400000>; |
| 189 |
}; |
| 190 |
|
| 191 |
mtd4@604000 { |
| 192 |
label = "phy3250-rootfs"; |
| 193 |
reg = <0x00604000 0x039fc000>; |
| 194 |
}; |
| 195 |
}; |
| 196 |
}; |
| 197 |
|
| 198 |
&ssp0 { |
| 199 |
num-cs = <1>; |
| 200 |
cs-gpios = <&gpio 3 5 0>; |
| 201 |
status = "okay"; |
| 202 |
|
| 203 |
eeprom: eeprom@0 { |
| 204 |
compatible = "atmel,at25"; |
| 205 |
reg = <0>; |
| 206 |
spi-max-frequency = <5000000>; |
| 207 |
|
| 208 |
pl022,interface = <0>; |
| 209 |
pl022,com-mode = <0>; |
| 210 |
pl022,rx-level-trig = <1>; |
| 211 |
pl022,tx-level-trig = <1>; |
| 212 |
pl022,ctrl-len = <11>; |
| 213 |
pl022,wait-state = <0>; |
| 214 |
pl022,duplex = <0>; |
| 215 |
|
| 216 |
size = <0x8000>; |
| 217 |
address-width = <16>; |
| 218 |
pagesize = <64>; |
| 219 |
}; |
| 220 |
}; |
| 221 |
|
| 222 |
&tsc { |
| 223 |
status = "okay"; |
| 224 |
}; |
| 225 |
|
| 226 |
&uart2 { |
| 227 |
status = "okay"; |
| 228 |
}; |
| 229 |
|
| 230 |
&uart3 { |
| 231 |
status = "okay"; |
| 232 |
}; |
| 233 |
|
| 234 |
&uart5 { |
| 235 |
status = "okay"; |
| 236 |
}; |