| 1 |
.. SPDX-License-Identifier: GPL-2.0 |
| 2 |
|
| 3 |
========================================== |
| 4 |
Broadcom RoboSwitch Ethernet switch driver |
| 5 |
========================================== |
| 6 |
|
| 7 |
The Broadcom RoboSwitch Ethernet switch family is used in quite a range of |
| 8 |
xDSL router, cable modems and other multimedia devices. |
| 9 |
|
| 10 |
The actual implementation supports the devices BCM5325E, BCM5365, BCM539x, |
| 11 |
BCM53115 and BCM53125 as well as BCM63XX. |
| 12 |
|
| 13 |
Implementation details |
| 14 |
====================== |
| 15 |
|
| 16 |
The driver is located in ``drivers/net/dsa/b53/`` and is implemented as a |
| 17 |
DSA driver; see ``Documentation/networking/dsa/dsa.rst`` for details on the |
| 18 |
subsystem and what it provides. |
| 19 |
|
| 20 |
The switch is, if possible, configured to enable a Broadcom specific 4-bytes |
| 21 |
switch tag which gets inserted by the switch for every packet forwarded to the |
| 22 |
CPU interface, conversely, the CPU network interface should insert a similar |
| 23 |
tag for packets entering the CPU port. The tag format is described in |
| 24 |
``net/dsa/tag_brcm.c``. |
| 25 |
|
| 26 |
The configuration of the device depends on whether or not tagging is |
| 27 |
supported. |
| 28 |
|
| 29 |
The interface names and example network configuration are used according the |
| 30 |
configuration described in the :ref:`dsa-config-showcases`. |
| 31 |
|
| 32 |
Configuration with tagging support |
| 33 |
---------------------------------- |
| 34 |
|
| 35 |
The tagging based configuration is desired. It is not specific to the b53 |
| 36 |
DSA driver and will work like all DSA drivers which supports tagging. |
| 37 |
|
| 38 |
See :ref:`dsa-tagged-configuration`. |
| 39 |
|
| 40 |
Configuration without tagging support |
| 41 |
------------------------------------- |
| 42 |
|
| 43 |
Older models (5325, 5365) support a different tag format that is not supported |
| 44 |
yet. 539x and 531x5 require managed mode and some special handling, which is |
| 45 |
also not yet supported. The tagging support is disabled in these cases and the |
| 46 |
switch need a different configuration. |
| 47 |
|
| 48 |
The configuration slightly differ from the :ref:`dsa-vlan-configuration`. |
| 49 |
|
| 50 |
The b53 tags the CPU port in all VLANs, since otherwise any PVID untagged |
| 51 |
VLAN programming would basically change the CPU port's default PVID and make |
| 52 |
it untagged, undesirable. |
| 53 |
|
| 54 |
In difference to the configuration described in :ref:`dsa-vlan-configuration` |
| 55 |
the default VLAN 1 has to be removed from the user interface configuration in |
| 56 |
single port and gateway configuration, while there is no need to add an extra |
| 57 |
VLAN configuration in the bridge showcase. |
| 58 |
|
| 59 |
single port |
| 60 |
~~~~~~~~~~~ |
| 61 |
The configuration can only be set up via VLAN tagging and bridge setup. |
| 62 |
By default packages are tagged with vid 1: |
| 63 |
|
| 64 |
.. code-block:: sh |
| 65 |
|
| 66 |
# tag traffic on CPU port |
| 67 |
ip link add link eth0 name eth0.1 type vlan id 1 |
| 68 |
ip link add link eth0 name eth0.2 type vlan id 2 |
| 69 |
ip link add link eth0 name eth0.3 type vlan id 3 |
| 70 |
|
| 71 |
# The conduit interface needs to be brought up before the user ports. |
| 72 |
ip link set eth0 up |
| 73 |
ip link set eth0.1 up |
| 74 |
ip link set eth0.2 up |
| 75 |
ip link set eth0.3 up |
| 76 |
|
| 77 |
# bring up the user interfaces |
| 78 |
ip link set wan up |
| 79 |
ip link set lan1 up |
| 80 |
ip link set lan2 up |
| 81 |
|
| 82 |
# create bridge |
| 83 |
ip link add name br0 type bridge |
| 84 |
|
| 85 |
# activate VLAN filtering |
| 86 |
ip link set dev br0 type bridge vlan_filtering 1 |
| 87 |
|
| 88 |
# add ports to bridges |
| 89 |
ip link set dev wan master br0 |
| 90 |
ip link set dev lan1 master br0 |
| 91 |
ip link set dev lan2 master br0 |
| 92 |
|
| 93 |
# tag traffic on ports |
| 94 |
bridge vlan add dev lan1 vid 2 pvid untagged |
| 95 |
bridge vlan del dev lan1 vid 1 |
| 96 |
bridge vlan add dev lan2 vid 3 pvid untagged |
| 97 |
bridge vlan del dev lan2 vid 1 |
| 98 |
|
| 99 |
# configure the VLANs |
| 100 |
ip addr add 192.0.2.1/30 dev eth0.1 |
| 101 |
ip addr add 192.0.2.5/30 dev eth0.2 |
| 102 |
ip addr add 192.0.2.9/30 dev eth0.3 |
| 103 |
|
| 104 |
# bring up the bridge devices |
| 105 |
ip link set br0 up |
| 106 |
|
| 107 |
|
| 108 |
bridge |
| 109 |
~~~~~~ |
| 110 |
|
| 111 |
.. code-block:: sh |
| 112 |
|
| 113 |
# tag traffic on CPU port |
| 114 |
ip link add link eth0 name eth0.1 type vlan id 1 |
| 115 |
|
| 116 |
# The conduit interface needs to be brought up before the user ports. |
| 117 |
ip link set eth0 up |
| 118 |
ip link set eth0.1 up |
| 119 |
|
| 120 |
# bring up the user interfaces |
| 121 |
ip link set wan up |
| 122 |
ip link set lan1 up |
| 123 |
ip link set lan2 up |
| 124 |
|
| 125 |
# create bridge |
| 126 |
ip link add name br0 type bridge |
| 127 |
|
| 128 |
# activate VLAN filtering |
| 129 |
ip link set dev br0 type bridge vlan_filtering 1 |
| 130 |
|
| 131 |
# add ports to bridge |
| 132 |
ip link set dev wan master br0 |
| 133 |
ip link set dev lan1 master br0 |
| 134 |
ip link set dev lan2 master br0 |
| 135 |
ip link set eth0.1 master br0 |
| 136 |
|
| 137 |
# configure the bridge |
| 138 |
ip addr add 192.0.2.129/25 dev br0 |
| 139 |
|
| 140 |
# bring up the bridge |
| 141 |
ip link set dev br0 up |
| 142 |
|
| 143 |
gateway |
| 144 |
~~~~~~~ |
| 145 |
|
| 146 |
.. code-block:: sh |
| 147 |
|
| 148 |
# tag traffic on CPU port |
| 149 |
ip link add link eth0 name eth0.1 type vlan id 1 |
| 150 |
ip link add link eth0 name eth0.2 type vlan id 2 |
| 151 |
|
| 152 |
# The conduit interface needs to be brought up before the user ports. |
| 153 |
ip link set eth0 up |
| 154 |
ip link set eth0.1 up |
| 155 |
ip link set eth0.2 up |
| 156 |
|
| 157 |
# bring up the user interfaces |
| 158 |
ip link set wan up |
| 159 |
ip link set lan1 up |
| 160 |
ip link set lan2 up |
| 161 |
|
| 162 |
# create bridge |
| 163 |
ip link add name br0 type bridge |
| 164 |
|
| 165 |
# activate VLAN filtering |
| 166 |
ip link set dev br0 type bridge vlan_filtering 1 |
| 167 |
|
| 168 |
# add ports to bridges |
| 169 |
ip link set dev wan master br0 |
| 170 |
ip link set eth0.1 master br0 |
| 171 |
ip link set dev lan1 master br0 |
| 172 |
ip link set dev lan2 master br0 |
| 173 |
|
| 174 |
# tag traffic on ports |
| 175 |
bridge vlan add dev wan vid 2 pvid untagged |
| 176 |
bridge vlan del dev wan vid 1 |
| 177 |
|
| 178 |
# configure the VLANs |
| 179 |
ip addr add 192.0.2.1/30 dev eth0.2 |
| 180 |
ip addr add 192.0.2.129/25 dev br0 |
| 181 |
|
| 182 |
# bring up the bridge devices |
| 183 |
ip link set br0 up |