| 1 |
.. SPDX-License-Identifier: GPL-2.0 |
| 2 |
|
| 3 |
===================== |
| 4 |
TLAN driver for Linux |
| 5 |
===================== |
| 6 |
|
| 7 |
:Version: 1.14a |
| 8 |
|
| 9 |
(C) 1997-1998 Caldera, Inc. |
| 10 |
|
| 11 |
(C) 1998 James Banks |
| 12 |
|
| 13 |
(C) 1999-2001 Torben Mathiasen <[email protected], [email protected]> |
| 14 |
|
| 15 |
For driver information/updates visit http://www.compaq.com |
| 16 |
|
| 17 |
|
| 18 |
|
| 19 |
|
| 20 |
|
| 21 |
I. Supported Devices |
| 22 |
==================== |
| 23 |
|
| 24 |
Only PCI devices will work with this driver. |
| 25 |
|
| 26 |
Supported: |
| 27 |
|
| 28 |
========= ========= =========================================== |
| 29 |
Vendor ID Device ID Name |
| 30 |
========= ========= =========================================== |
| 31 |
0e11 ae32 Compaq Netelligent 10/100 TX PCI UTP |
| 32 |
0e11 ae34 Compaq Netelligent 10 T PCI UTP |
| 33 |
0e11 ae35 Compaq Integrated NetFlex 3/P |
| 34 |
0e11 ae40 Compaq Netelligent Dual 10/100 TX PCI UTP |
| 35 |
0e11 ae43 Compaq Netelligent Integrated 10/100 TX UTP |
| 36 |
0e11 b011 Compaq Netelligent 10/100 TX Embedded UTP |
| 37 |
0e11 b012 Compaq Netelligent 10 T/2 PCI UTP/Coax |
| 38 |
0e11 b030 Compaq Netelligent 10/100 TX UTP |
| 39 |
0e11 f130 Compaq NetFlex 3/P |
| 40 |
0e11 f150 Compaq NetFlex 3/P |
| 41 |
108d 0012 Olicom OC-2325 |
| 42 |
108d 0013 Olicom OC-2183 |
| 43 |
108d 0014 Olicom OC-2326 |
| 44 |
========= ========= =========================================== |
| 45 |
|
| 46 |
|
| 47 |
Caveats: |
| 48 |
|
| 49 |
I am not sure if 100BaseTX daughterboards (for those cards which |
| 50 |
support such things) will work. I haven't had any solid evidence |
| 51 |
either way. |
| 52 |
|
| 53 |
However, if a card supports 100BaseTx without requiring an add |
| 54 |
on daughterboard, it should work with 100BaseTx. |
| 55 |
|
| 56 |
The "Netelligent 10 T/2 PCI UTP/Coax" (b012) device is untested, |
| 57 |
but I do not expect any problems. |
| 58 |
|
| 59 |
|
| 60 |
II. Driver Options |
| 61 |
================== |
| 62 |
|
| 63 |
1. You can append debug=x to the end of the insmod line to get |
| 64 |
debug messages, where x is a bit field where the bits mean |
| 65 |
the following: |
| 66 |
|
| 67 |
==== ===================================== |
| 68 |
0x01 Turn on general debugging messages. |
| 69 |
0x02 Turn on receive debugging messages. |
| 70 |
0x04 Turn on transmit debugging messages. |
| 71 |
0x08 Turn on list debugging messages. |
| 72 |
==== ===================================== |
| 73 |
|
| 74 |
2. You can append aui=1 to the end of the insmod line to cause |
| 75 |
the adapter to use the AUI interface instead of the 10 Base T |
| 76 |
interface. This is also what to do if you want to use the BNC |
| 77 |
connector on a TLAN based device. (Setting this option on a |
| 78 |
device that does not have an AUI/BNC connector will probably |
| 79 |
cause it to not function correctly.) |
| 80 |
|
| 81 |
3. You can set duplex=1 to force half duplex, and duplex=2 to |
| 82 |
force full duplex. |
| 83 |
|
| 84 |
4. You can set speed=10 to force 10Mbs operation, and speed=100 |
| 85 |
to force 100Mbs operation. (I'm not sure what will happen |
| 86 |
if a card which only supports 10Mbs is forced into 100Mbs |
| 87 |
mode.) |
| 88 |
|
| 89 |
5. You have to use speed=X duplex=Y together now. If you just |
| 90 |
do "insmod tlan.o speed=100" the driver will do Auto-Neg. |
| 91 |
To force a 10Mbps Half-Duplex link do "insmod tlan.o speed=10 |
| 92 |
duplex=1". |
| 93 |
|
| 94 |
6. If the driver is built into the kernel, you can use the 3rd |
| 95 |
and 4th parameters to set aui and debug respectively. For |
| 96 |
example:: |
| 97 |
|
| 98 |
ether=0,0,0x1,0x7,eth0 |
| 99 |
|
| 100 |
This sets aui to 0x1 and debug to 0x7, assuming eth0 is a |
| 101 |
supported TLAN device. |
| 102 |
|
| 103 |
The bits in the third byte are assigned as follows: |
| 104 |
|
| 105 |
==== =============== |
| 106 |
0x01 aui |
| 107 |
0x02 use half duplex |
| 108 |
0x04 use full duplex |
| 109 |
0x08 use 10BaseT |
| 110 |
0x10 use 100BaseTx |
| 111 |
==== =============== |
| 112 |
|
| 113 |
You also need to set both speed and duplex settings when forcing |
| 114 |
speeds with kernel-parameters. |
| 115 |
ether=0,0,0x12,0,eth0 will force link to 100Mbps Half-Duplex. |
| 116 |
|
| 117 |
7. If you have more than one tlan adapter in your system, you can |
| 118 |
use the above options on a per adapter basis. To force a 100Mbit/HD |
| 119 |
link with your eth1 adapter use:: |
| 120 |
|
| 121 |
insmod tlan speed=0,100 duplex=0,1 |
| 122 |
|
| 123 |
Now eth0 will use auto-neg and eth1 will be forced to 100Mbit/HD. |
| 124 |
Note that the tlan driver supports a maximum of 8 adapters. |
| 125 |
|
| 126 |
|
| 127 |
III. Things to try if you have problems |
| 128 |
======================================= |
| 129 |
|
| 130 |
1. Make sure your card's PCI id is among those listed in |
| 131 |
section I, above. |
| 132 |
2. Make sure routing is correct. |
| 133 |
3. Try forcing different speed/duplex settings |
| 134 |
|
| 135 |
|
| 136 |
There is also a tlan mailing list which you can join by sending "subscribe tlan" |
| 137 |
in the body of an email to [email protected]. |
| 138 |
|
| 139 |
There is also a tlan website at http://www.compaq.com |
| 140 |
|