| 1 |
.. SPDX-License-Identifier: GPL-2.0 |
| 2 |
|
| 3 |
====================================== |
| 4 |
Texas Instruments CPSW ethernet driver |
| 5 |
====================================== |
| 6 |
|
| 7 |
Multiqueue & CBS & MQPRIO |
| 8 |
========================= |
| 9 |
|
| 10 |
|
| 11 |
The cpsw has 3 CBS shapers for each external ports. This document |
| 12 |
describes MQPRIO and CBS Qdisc offload configuration for cpsw driver |
| 13 |
based on examples. It potentially can be used in audio video bridging |
| 14 |
(AVB) and time sensitive networking (TSN). |
| 15 |
|
| 16 |
The following examples were tested on AM572x EVM and BBB boards. |
| 17 |
|
| 18 |
Test setup |
| 19 |
========== |
| 20 |
|
| 21 |
Under consideration two examples with AM572x EVM running cpsw driver |
| 22 |
in dual_emac mode. |
| 23 |
|
| 24 |
Several prerequisites: |
| 25 |
|
| 26 |
- TX queues must be rated starting from txq0 that has highest priority |
| 27 |
- Traffic classes are used starting from 0, that has highest priority |
| 28 |
- CBS shapers should be used with rated queues |
| 29 |
- The bandwidth for CBS shapers has to be set a little bit more then |
| 30 |
potential incoming rate, thus, rate of all incoming tx queues has |
| 31 |
to be a little less |
| 32 |
- Real rates can differ, due to discreetness |
| 33 |
- Map skb-priority to txq is not enough, also skb-priority to l2 prio |
| 34 |
map has to be created with ip or vconfig tool |
| 35 |
- Any l2/socket prio (0 - 7) for classes can be used, but for |
| 36 |
simplicity default values are used: 3 and 2 |
| 37 |
- only 2 classes tested: A and B, but checked and can work with more, |
| 38 |
maximum allowed 4, but only for 3 rate can be set. |
| 39 |
|
| 40 |
Test setup for examples |
| 41 |
======================= |
| 42 |
|
| 43 |
:: |
| 44 |
|
| 45 |
+-------------------------------+ |
| 46 |
|--+ | |
| 47 |
| | Workstation0 | |
| 48 |
|E | MAC 18:03:73:66:87:42 | |
| 49 |
+-----------------------------+ +--|t | | |
| 50 |
| | 1 | E | | |h |./tsn_listener -d \ | |
| 51 |
| Target board: | 0 | t |--+ |0 | 18:03:73:66:87:42 -i eth0 \| |
| 52 |
| AM572x EVM | 0 | h | | | -s 1500 | |
| 53 |
| | 0 | 0 | |--+ | |
| 54 |
| Only 2 classes: |Mb +---| +-------------------------------+ |
| 55 |
| class A, class B | | |
| 56 |
| | +---| +-------------------------------+ |
| 57 |
| | 1 | E | |--+ | |
| 58 |
| | 0 | t | | | Workstation1 | |
| 59 |
| | 0 | h |--+ |E | MAC 20:cf:30:85:7d:fd | |
| 60 |
| |Mb | 1 | +--|t | | |
| 61 |
+-----------------------------+ |h |./tsn_listener -d \ | |
| 62 |
|0 | 20:cf:30:85:7d:fd -i eth0 \| |
| 63 |
| | -s 1500 | |
| 64 |
|--+ | |
| 65 |
+-------------------------------+ |
| 66 |
|
| 67 |
|
| 68 |
Example 1: One port tx AVB configuration scheme for target board |
| 69 |
---------------------------------------------------------------- |
| 70 |
|
| 71 |
(prints and scheme for AM572x evm, applicable for single port boards) |
| 72 |
|
| 73 |
- tc - traffic class |
| 74 |
- txq - transmit queue |
| 75 |
- p - priority |
| 76 |
- f - fifo (cpsw fifo) |
| 77 |
- S - shaper configured |
| 78 |
|
| 79 |
:: |
| 80 |
|
| 81 |
+------------------------------------------------------------------+ u |
| 82 |
| +---------------+ +---------------+ +------+ +------+ | s |
| 83 |
| | | | | | | | | | e |
| 84 |
| | App 1 | | App 2 | | Apps | | Apps | | r |
| 85 |
| | Class A | | Class B | | Rest | | Rest | | |
| 86 |
| | Eth0 | | Eth0 | | Eth0 | | Eth1 | | s |
| 87 |
| | VLAN100 | | VLAN100 | | | | | | | | p |
| 88 |
| | 40 Mb/s | | 20 Mb/s | | | | | | | | a |
| 89 |
| | SO_PRIORITY=3 | | SO_PRIORITY=2 | | | | | | | | c |
| 90 |
| | | | | | | | | | | | | | e |
| 91 |
| +---|-----------+ +---|-----------+ +---|--+ +---|--+ | |
| 92 |
+-----|------------------|------------------|--------|-------------+ |
| 93 |
+-+ +------------+ | | |
| 94 |
| | +-----------------+ +--+ |
| 95 |
| | | | |
| 96 |
+---|-------|-------------|-----------------------|----------------+ |
| 97 |
| +----+ +----+ +----+ +----+ +----+ | |
| 98 |
| | p3 | | p2 | | p1 | | p0 | | p0 | | k |
| 99 |
| \ / \ / \ / \ / \ / | e |
| 100 |
| \ / \ / \ / \ / \ / | r |
| 101 |
| \/ \/ \/ \/ \/ | n |
| 102 |
| | | | | | e |
| 103 |
| | | +-----+ | | l |
| 104 |
| | | | | | |
| 105 |
| +----+ +----+ +----+ +----+ | s |
| 106 |
| |tc0 | |tc1 | |tc2 | |tc0 | | p |
| 107 |
| \ / \ / \ / \ / | a |
| 108 |
| \ / \ / \ / \ / | c |
| 109 |
| \/ \/ \/ \/ | e |
| 110 |
| | | +-----+ | | |
| 111 |
| | | | | | | |
| 112 |
| | | | | | | |
| 113 |
| | | | | | | |
| 114 |
| +----+ +----+ +----+ +----+ +----+ | |
| 115 |
| |txq0| |txq1| |txq2| |txq3| |txq4| | |
| 116 |
| \ / \ / \ / \ / \ / | |
| 117 |
| \ / \ / \ / \ / \ / | |
| 118 |
| \/ \/ \/ \/ \/ | |
| 119 |
| +-|------|------|------|--+ +--|--------------+ | |
| 120 |
| | | | | | | Eth0.100 | | Eth1 | | |
| 121 |
+---|------|------|------|------------------------|----------------+ |
| 122 |
| | | | | |
| 123 |
p p p p | |
| 124 |
3 2 0-1, 4-7 <- L2 priority | |
| 125 |
| | | | | |
| 126 |
| | | | | |
| 127 |
+---|------|------|------|------------------------|----------------+ |
| 128 |
| | | | | |----------+ | |
| 129 |
| +----+ +----+ +----+ +----+ +----+ | |
| 130 |
| |dma7| |dma6| |dma5| |dma4| |dma3| | |
| 131 |
| \ / \ / \ / \ / \ / | c |
| 132 |
| \S / \S / \ / \ / \ / | p |
| 133 |
| \/ \/ \/ \/ \/ | s |
| 134 |
| | | | +----- | | w |
| 135 |
| | | | | | | |
| 136 |
| | | | | | | d |
| 137 |
| +----+ +----+ +----+p p+----+ | r |
| 138 |
| | | | | | |o o| | | i |
| 139 |
| | f3 | | f2 | | f0 |r r| f0 | | v |
| 140 |
| |tc0 | |tc1 | |tc2 |t t|tc0 | | e |
| 141 |
| \CBS / \CBS / \CBS /1 2\CBS / | r |
| 142 |
| \S / \S / \ / \ / | |
| 143 |
| \/ \/ \/ \/ | |
| 144 |
+------------------------------------------------------------------+ |
| 145 |
|
| 146 |
|
| 147 |
1) :: |
| 148 |
|
| 149 |
|
| 150 |
// Add 4 tx queues, for interface Eth0, and 1 tx queue for Eth1 |
| 151 |
$ ethtool -L eth0 rx 1 tx 5 |
| 152 |
rx unmodified, ignoring |
| 153 |
|
| 154 |
2) :: |
| 155 |
|
| 156 |
// Check if num of queues is set correctly: |
| 157 |
$ ethtool -l eth0 |
| 158 |
Channel parameters for eth0: |
| 159 |
Pre-set maximums: |
| 160 |
RX: 8 |
| 161 |
TX: 8 |
| 162 |
Other: 0 |
| 163 |
Combined: 0 |
| 164 |
Current hardware settings: |
| 165 |
RX: 1 |
| 166 |
TX: 5 |
| 167 |
Other: 0 |
| 168 |
Combined: 0 |
| 169 |
|
| 170 |
3) :: |
| 171 |
|
| 172 |
// TX queues must be rated starting from 0, so set bws for tx0 and tx1 |
| 173 |
// Set rates 40 and 20 Mb/s appropriately. |
| 174 |
// Pay attention, real speed can differ a bit due to discreetness. |
| 175 |
// Leave last 2 tx queues not rated. |
| 176 |
$ echo 40 > /sys/class/net/eth0/queues/tx-0/tx_maxrate |
| 177 |
$ echo 20 > /sys/class/net/eth0/queues/tx-1/tx_maxrate |
| 178 |
|
| 179 |
4) :: |
| 180 |
|
| 181 |
// Check maximum rate of tx (cpdma) queues: |
| 182 |
$ cat /sys/class/net/eth0/queues/tx-*/tx_maxrate |
| 183 |
40 |
| 184 |
20 |
| 185 |
0 |
| 186 |
0 |
| 187 |
0 |
| 188 |
|
| 189 |
5) :: |
| 190 |
|
| 191 |
// Map skb->priority to traffic class: |
| 192 |
// 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 |
| 193 |
// Map traffic class to transmit queue: |
| 194 |
// tc0 -> txq0, tc1 -> txq1, tc2 -> (txq2, txq3) |
| 195 |
$ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \ |
| 196 |
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1 |
| 197 |
|
| 198 |
5a) :: |
| 199 |
|
| 200 |
// As two interface sharing same set of tx queues, assign all traffic |
| 201 |
// coming to interface Eth1 to separate queue in order to not mix it |
| 202 |
// with traffic from interface Eth0, so use separate txq to send |
| 203 |
// packets to Eth1, so all prio -> tc0 and tc0 -> txq4 |
| 204 |
// Here hw 0, so here still default configuration for eth1 in hw |
| 205 |
$ tc qdisc replace dev eth1 handle 100: parent root mqprio num_tc 1 \ |
| 206 |
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 queues 1@4 hw 0 |
| 207 |
|
| 208 |
6) :: |
| 209 |
|
| 210 |
// Check classes settings |
| 211 |
$ tc -g class show dev eth0 |
| 212 |
+---(100:ffe2) mqprio |
| 213 |
| +---(100:3) mqprio |
| 214 |
| +---(100:4) mqprio |
| 215 |
| |
| 216 |
+---(100:ffe1) mqprio |
| 217 |
| +---(100:2) mqprio |
| 218 |
| |
| 219 |
+---(100:ffe0) mqprio |
| 220 |
+---(100:1) mqprio |
| 221 |
|
| 222 |
$ tc -g class show dev eth1 |
| 223 |
+---(100:ffe0) mqprio |
| 224 |
+---(100:5) mqprio |
| 225 |
|
| 226 |
7) :: |
| 227 |
|
| 228 |
// Set rate for class A - 41 Mbit (tc0, txq0) using CBS Qdisc |
| 229 |
// Set it +1 Mb for reserve (important!) |
| 230 |
// here only idle slope is important, others arg are ignored |
| 231 |
// Pay attention, real speed can differ a bit due to discreetness |
| 232 |
$ tc qdisc add dev eth0 parent 100:1 cbs locredit -1438 \ |
| 233 |
hicredit 62 sendslope -959000 idleslope 41000 offload 1 |
| 234 |
net eth0: set FIFO3 bw = 50 |
| 235 |
|
| 236 |
8) :: |
| 237 |
|
| 238 |
// Set rate for class B - 21 Mbit (tc1, txq1) using CBS Qdisc: |
| 239 |
// Set it +1 Mb for reserve (important!) |
| 240 |
$ tc qdisc add dev eth0 parent 100:2 cbs locredit -1468 \ |
| 241 |
hicredit 65 sendslope -979000 idleslope 21000 offload 1 |
| 242 |
net eth0: set FIFO2 bw = 30 |
| 243 |
|
| 244 |
9) :: |
| 245 |
|
| 246 |
// Create vlan 100 to map sk->priority to vlan qos |
| 247 |
$ ip link add link eth0 name eth0.100 type vlan id 100 |
| 248 |
8021q: 802.1Q VLAN Support v1.8 |
| 249 |
8021q: adding VLAN 0 to HW filter on device eth0 |
| 250 |
8021q: adding VLAN 0 to HW filter on device eth1 |
| 251 |
net eth0: Adding vlanid 100 to vlan filter |
| 252 |
|
| 253 |
10) :: |
| 254 |
|
| 255 |
// Map skb->priority to L2 prio, 1 to 1 |
| 256 |
$ ip link set eth0.100 type vlan \ |
| 257 |
egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| 258 |
|
| 259 |
11) :: |
| 260 |
|
| 261 |
// Check egress map for vlan 100 |
| 262 |
$ cat /proc/net/vlan/eth0.100 |
| 263 |
[...] |
| 264 |
INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 |
| 265 |
EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| 266 |
|
| 267 |
12) :: |
| 268 |
|
| 269 |
// Run your appropriate tools with socket option "SO_PRIORITY" |
| 270 |
// to 3 for class A and/or to 2 for class B |
| 271 |
// (I took at https://lore.kernel.org/r/[email protected]/) |
| 272 |
./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p3 -s 1500& |
| 273 |
./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p2 -s 1500& |
| 274 |
|
| 275 |
13) :: |
| 276 |
|
| 277 |
// run your listener on workstation (should be in same vlan) |
| 278 |
// (I took at https://lore.kernel.org/r/[email protected]/) |
| 279 |
./tsn_listener -d 18:03:73:66:87:42 -i enp5s0 -s 1500 |
| 280 |
Receiving data rate: 39012 kbps |
| 281 |
Receiving data rate: 39012 kbps |
| 282 |
Receiving data rate: 39012 kbps |
| 283 |
Receiving data rate: 39012 kbps |
| 284 |
Receiving data rate: 39012 kbps |
| 285 |
Receiving data rate: 39012 kbps |
| 286 |
Receiving data rate: 39012 kbps |
| 287 |
Receiving data rate: 39012 kbps |
| 288 |
Receiving data rate: 39012 kbps |
| 289 |
Receiving data rate: 39012 kbps |
| 290 |
Receiving data rate: 39012 kbps |
| 291 |
Receiving data rate: 39012 kbps |
| 292 |
Receiving data rate: 39000 kbps |
| 293 |
|
| 294 |
14) :: |
| 295 |
|
| 296 |
// Restore default configuration if needed |
| 297 |
$ ip link del eth0.100 |
| 298 |
$ tc qdisc del dev eth1 root |
| 299 |
$ tc qdisc del dev eth0 root |
| 300 |
net eth0: Prev FIFO2 is shaped |
| 301 |
net eth0: set FIFO3 bw = 0 |
| 302 |
net eth0: set FIFO2 bw = 0 |
| 303 |
$ ethtool -L eth0 rx 1 tx 1 |
| 304 |
|
| 305 |
Example 2: Two port tx AVB configuration scheme for target board |
| 306 |
---------------------------------------------------------------- |
| 307 |
|
| 308 |
(prints and scheme for AM572x evm, for dual emac boards only) |
| 309 |
|
| 310 |
:: |
| 311 |
|
| 312 |
+------------------------------------------------------------------+ u |
| 313 |
| +----------+ +----------+ +------+ +----------+ +----------+ | s |
| 314 |
| | | | | | | | | | | | e |
| 315 |
| | App 1 | | App 2 | | Apps | | App 3 | | App 4 | | r |
| 316 |
| | Class A | | Class B | | Rest | | Class B | | Class A | | |
| 317 |
| | Eth0 | | Eth0 | | | | | Eth1 | | Eth1 | | s |
| 318 |
| | VLAN100 | | VLAN100 | | | | | VLAN100 | | VLAN100 | | p |
| 319 |
| | 40 Mb/s | | 20 Mb/s | | | | | 10 Mb/s | | 30 Mb/s | | a |
| 320 |
| | SO_PRI=3 | | SO_PRI=2 | | | | | SO_PRI=3 | | SO_PRI=2 | | c |
| 321 |
| | | | | | | | | | | | | | | | | e |
| 322 |
| +---|------+ +---|------+ +---|--+ +---|------+ +---|------+ | |
| 323 |
+-----|-------------|-------------|---------|-------------|--------+ |
| 324 |
+-+ +-------+ | +----------+ +----+ |
| 325 |
| | +-------+------+ | | |
| 326 |
| | | | | | |
| 327 |
+---|-------|-------------|--------------|-------------|-------|---+ |
| 328 |
| +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+ | |
| 329 |
| | p3 | | p2 | | p1 | | p0 | | p0 | | p1 | | p2 | | p3 | | k |
| 330 |
| \ / \ / \ / \ / \ / \ / \ / \ / | e |
| 331 |
| \ / \ / \ / \ / \ / \ / \ / \ / | r |
| 332 |
| \/ \/ \/ \/ \/ \/ \/ \/ | n |
| 333 |
| | | | | | | | e |
| 334 |
| | | +----+ +----+ | | | l |
| 335 |
| | | | | | | | |
| 336 |
| +----+ +----+ +----+ +----+ +----+ +----+ | s |
| 337 |
| |tc0 | |tc1 | |tc2 | |tc2 | |tc1 | |tc0 | | p |
| 338 |
| \ / \ / \ / \ / \ / \ / | a |
| 339 |
| \ / \ / \ / \ / \ / \ / | c |
| 340 |
| \/ \/ \/ \/ \/ \/ | e |
| 341 |
| | | +-----+ +-----+ | | | |
| 342 |
| | | | | | | | | | |
| 343 |
| | | | | | | | | | |
| 344 |
| | | | | E E | | | | | |
| 345 |
| +----+ +----+ +----+ +----+ t t +----+ +----+ +----+ +----+ | |
| 346 |
| |txq0| |txq1| |txq4| |txq5| h h |txq6| |txq7| |txq3| |txq2| | |
| 347 |
| \ / \ / \ / \ / 0 1 \ / \ / \ / \ / | |
| 348 |
| \ / \ / \ / \ / . . \ / \ / \ / \ / | |
| 349 |
| \/ \/ \/ \/ 1 1 \/ \/ \/ \/ | |
| 350 |
| +-|------|------|------|--+ 0 0 +-|------|------|------|--+ | |
| 351 |
| | | | | | | 0 0 | | | | | | | |
| 352 |
+---|------|------|------|---------------|------|------|------|----+ |
| 353 |
| | | | | | | | |
| 354 |
p p p p p p p p |
| 355 |
3 2 0-1, 4-7 <-L2 pri-> 0-1, 4-7 2 3 |
| 356 |
| | | | | | | | |
| 357 |
| | | | | | | | |
| 358 |
+---|------|------|------|---------------|------|------|------|----+ |
| 359 |
| | | | | | | | | | |
| 360 |
| +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+ | |
| 361 |
| |dma7| |dma6| |dma3| |dma2| |dma1| |dma0| |dma4| |dma5| | |
| 362 |
| \ / \ / \ / \ / \ / \ / \ / \ / | c |
| 363 |
| \S / \S / \ / \ / \ / \ / \S / \S / | p |
| 364 |
| \/ \/ \/ \/ \/ \/ \/ \/ | s |
| 365 |
| | | | +----- | | | | | w |
| 366 |
| | | | | +----+ | | | | |
| 367 |
| | | | | | | | | | d |
| 368 |
| +----+ +----+ +----+p p+----+ +----+ +----+ | r |
| 369 |
| | | | | | |o o| | | | | | | i |
| 370 |
| | f3 | | f2 | | f0 |r CPSW r| f3 | | f2 | | f0 | | v |
| 371 |
| |tc0 | |tc1 | |tc2 |t t|tc0 | |tc1 | |tc2 | | e |
| 372 |
| \CBS / \CBS / \CBS /1 2\CBS / \CBS / \CBS / | r |
| 373 |
| \S / \S / \ / \S / \S / \ / | |
| 374 |
| \/ \/ \/ \/ \/ \/ | |
| 375 |
+------------------------------------------------------------------+ |
| 376 |
========================================Eth==========================> |
| 377 |
|
| 378 |
1) :: |
| 379 |
|
| 380 |
// Add 8 tx queues, for interface Eth0, but they are common, so are accessed |
| 381 |
// by two interfaces Eth0 and Eth1. |
| 382 |
$ ethtool -L eth1 rx 1 tx 8 |
| 383 |
rx unmodified, ignoring |
| 384 |
|
| 385 |
2) :: |
| 386 |
|
| 387 |
// Check if num of queues is set correctly: |
| 388 |
$ ethtool -l eth0 |
| 389 |
Channel parameters for eth0: |
| 390 |
Pre-set maximums: |
| 391 |
RX: 8 |
| 392 |
TX: 8 |
| 393 |
Other: 0 |
| 394 |
Combined: 0 |
| 395 |
Current hardware settings: |
| 396 |
RX: 1 |
| 397 |
TX: 8 |
| 398 |
Other: 0 |
| 399 |
Combined: 0 |
| 400 |
|
| 401 |
3) :: |
| 402 |
|
| 403 |
// TX queues must be rated starting from 0, so set bws for tx0 and tx1 for Eth0 |
| 404 |
// and for tx2 and tx3 for Eth1. That is, rates 40 and 20 Mb/s appropriately |
| 405 |
// for Eth0 and 30 and 10 Mb/s for Eth1. |
| 406 |
// Real speed can differ a bit due to discreetness |
| 407 |
// Leave last 4 tx queues as not rated |
| 408 |
$ echo 40 > /sys/class/net/eth0/queues/tx-0/tx_maxrate |
| 409 |
$ echo 20 > /sys/class/net/eth0/queues/tx-1/tx_maxrate |
| 410 |
$ echo 30 > /sys/class/net/eth1/queues/tx-2/tx_maxrate |
| 411 |
$ echo 10 > /sys/class/net/eth1/queues/tx-3/tx_maxrate |
| 412 |
|
| 413 |
4) :: |
| 414 |
|
| 415 |
// Check maximum rate of tx (cpdma) queues: |
| 416 |
$ cat /sys/class/net/eth0/queues/tx-*/tx_maxrate |
| 417 |
40 |
| 418 |
20 |
| 419 |
30 |
| 420 |
10 |
| 421 |
0 |
| 422 |
0 |
| 423 |
0 |
| 424 |
0 |
| 425 |
|
| 426 |
5) :: |
| 427 |
|
| 428 |
// Map skb->priority to traffic class for Eth0: |
| 429 |
// 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 |
| 430 |
// Map traffic class to transmit queue: |
| 431 |
// tc0 -> txq0, tc1 -> txq1, tc2 -> (txq4, txq5) |
| 432 |
$ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \ |
| 433 |
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@4 hw 1 |
| 434 |
|
| 435 |
6) :: |
| 436 |
|
| 437 |
// Check classes settings |
| 438 |
$ tc -g class show dev eth0 |
| 439 |
+---(100:ffe2) mqprio |
| 440 |
| +---(100:5) mqprio |
| 441 |
| +---(100:6) mqprio |
| 442 |
| |
| 443 |
+---(100:ffe1) mqprio |
| 444 |
| +---(100:2) mqprio |
| 445 |
| |
| 446 |
+---(100:ffe0) mqprio |
| 447 |
+---(100:1) mqprio |
| 448 |
|
| 449 |
7) :: |
| 450 |
|
| 451 |
// Set rate for class A - 41 Mbit (tc0, txq0) using CBS Qdisc for Eth0 |
| 452 |
// here only idle slope is important, others ignored |
| 453 |
// Real speed can differ a bit due to discreetness |
| 454 |
$ tc qdisc add dev eth0 parent 100:1 cbs locredit -1470 \ |
| 455 |
hicredit 62 sendslope -959000 idleslope 41000 offload 1 |
| 456 |
net eth0: set FIFO3 bw = 50 |
| 457 |
|
| 458 |
8) :: |
| 459 |
|
| 460 |
// Set rate for class B - 21 Mbit (tc1, txq1) using CBS Qdisc for Eth0 |
| 461 |
$ tc qdisc add dev eth0 parent 100:2 cbs locredit -1470 \ |
| 462 |
hicredit 65 sendslope -979000 idleslope 21000 offload 1 |
| 463 |
net eth0: set FIFO2 bw = 30 |
| 464 |
|
| 465 |
9) :: |
| 466 |
|
| 467 |
// Create vlan 100 to map sk->priority to vlan qos for Eth0 |
| 468 |
$ ip link add link eth0 name eth0.100 type vlan id 100 |
| 469 |
net eth0: Adding vlanid 100 to vlan filter |
| 470 |
|
| 471 |
10) :: |
| 472 |
|
| 473 |
// Map skb->priority to L2 prio for Eth0.100, one to one |
| 474 |
$ ip link set eth0.100 type vlan \ |
| 475 |
egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| 476 |
|
| 477 |
11) :: |
| 478 |
|
| 479 |
// Check egress map for vlan 100 |
| 480 |
$ cat /proc/net/vlan/eth0.100 |
| 481 |
[...] |
| 482 |
INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 |
| 483 |
EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| 484 |
|
| 485 |
12) :: |
| 486 |
|
| 487 |
// Map skb->priority to traffic class for Eth1: |
| 488 |
// 3pri -> tc0, 2pri -> tc1, (0,1,4-7)pri -> tc2 |
| 489 |
// Map traffic class to transmit queue: |
| 490 |
// tc0 -> txq2, tc1 -> txq3, tc2 -> (txq6, txq7) |
| 491 |
$ tc qdisc replace dev eth1 handle 100: parent root mqprio num_tc 3 \ |
| 492 |
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@2 1@3 2@6 hw 1 |
| 493 |
|
| 494 |
13) :: |
| 495 |
|
| 496 |
// Check classes settings |
| 497 |
$ tc -g class show dev eth1 |
| 498 |
+---(100:ffe2) mqprio |
| 499 |
| +---(100:7) mqprio |
| 500 |
| +---(100:8) mqprio |
| 501 |
| |
| 502 |
+---(100:ffe1) mqprio |
| 503 |
| +---(100:4) mqprio |
| 504 |
| |
| 505 |
+---(100:ffe0) mqprio |
| 506 |
+---(100:3) mqprio |
| 507 |
|
| 508 |
14) :: |
| 509 |
|
| 510 |
// Set rate for class A - 31 Mbit (tc0, txq2) using CBS Qdisc for Eth1 |
| 511 |
// here only idle slope is important, others ignored, but calculated |
| 512 |
// for interface speed - 100Mb for eth1 port. |
| 513 |
// Set it +1 Mb for reserve (important!) |
| 514 |
$ tc qdisc add dev eth1 parent 100:3 cbs locredit -1035 \ |
| 515 |
hicredit 465 sendslope -69000 idleslope 31000 offload 1 |
| 516 |
net eth1: set FIFO3 bw = 31 |
| 517 |
|
| 518 |
15) :: |
| 519 |
|
| 520 |
// Set rate for class B - 11 Mbit (tc1, txq3) using CBS Qdisc for Eth1 |
| 521 |
// Set it +1 Mb for reserve (important!) |
| 522 |
$ tc qdisc add dev eth1 parent 100:4 cbs locredit -1335 \ |
| 523 |
hicredit 405 sendslope -89000 idleslope 11000 offload 1 |
| 524 |
net eth1: set FIFO2 bw = 11 |
| 525 |
|
| 526 |
16) :: |
| 527 |
|
| 528 |
// Create vlan 100 to map sk->priority to vlan qos for Eth1 |
| 529 |
$ ip link add link eth1 name eth1.100 type vlan id 100 |
| 530 |
net eth1: Adding vlanid 100 to vlan filter |
| 531 |
|
| 532 |
17) :: |
| 533 |
|
| 534 |
// Map skb->priority to L2 prio for Eth1.100, one to one |
| 535 |
$ ip link set eth1.100 type vlan \ |
| 536 |
egress 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| 537 |
|
| 538 |
18) :: |
| 539 |
|
| 540 |
// Check egress map for vlan 100 |
| 541 |
$ cat /proc/net/vlan/eth1.100 |
| 542 |
[...] |
| 543 |
INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 |
| 544 |
EGRESS priority mappings: 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7 |
| 545 |
|
| 546 |
19) :: |
| 547 |
|
| 548 |
// Run appropriate tools with socket option "SO_PRIORITY" to 3 |
| 549 |
// for class A and to 2 for class B. For both interfaces |
| 550 |
./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p2 -s 1500& |
| 551 |
./tsn_talker -d 18:03:73:66:87:42 -i eth0.100 -p3 -s 1500& |
| 552 |
./tsn_talker -d 20:cf:30:85:7d:fd -i eth1.100 -p2 -s 1500& |
| 553 |
./tsn_talker -d 20:cf:30:85:7d:fd -i eth1.100 -p3 -s 1500& |
| 554 |
|
| 555 |
20) :: |
| 556 |
|
| 557 |
// run your listener on workstation (should be in same vlan) |
| 558 |
// (I took at https://lore.kernel.org/r/[email protected]/) |
| 559 |
./tsn_listener -d 18:03:73:66:87:42 -i enp5s0 -s 1500 |
| 560 |
Receiving data rate: 39012 kbps |
| 561 |
Receiving data rate: 39012 kbps |
| 562 |
Receiving data rate: 39012 kbps |
| 563 |
Receiving data rate: 39012 kbps |
| 564 |
Receiving data rate: 39012 kbps |
| 565 |
Receiving data rate: 39012 kbps |
| 566 |
Receiving data rate: 39012 kbps |
| 567 |
Receiving data rate: 39012 kbps |
| 568 |
Receiving data rate: 39012 kbps |
| 569 |
Receiving data rate: 39012 kbps |
| 570 |
Receiving data rate: 39012 kbps |
| 571 |
Receiving data rate: 39012 kbps |
| 572 |
Receiving data rate: 39000 kbps |
| 573 |
|
| 574 |
21) :: |
| 575 |
|
| 576 |
// Restore default configuration if needed |
| 577 |
$ ip link del eth1.100 |
| 578 |
$ ip link del eth0.100 |
| 579 |
$ tc qdisc del dev eth1 root |
| 580 |
net eth1: Prev FIFO2 is shaped |
| 581 |
net eth1: set FIFO3 bw = 0 |
| 582 |
net eth1: set FIFO2 bw = 0 |
| 583 |
$ tc qdisc del dev eth0 root |
| 584 |
net eth0: Prev FIFO2 is shaped |
| 585 |
net eth0: set FIFO3 bw = 0 |
| 586 |
net eth0: set FIFO2 bw = 0 |
| 587 |
$ ethtool -L eth0 rx 1 tx 1 |