| 1 |
/* hermes.h |
| 2 |
* |
| 3 |
* Driver core for the "Hermes" wireless MAC controller, as used in |
| 4 |
* the Lucent Orinoco and Cabletron RoamAbout cards. It should also |
| 5 |
* work on the hfa3841 and hfa3842 MAC controller chips used in the |
| 6 |
* Prism I & II chipsets. |
| 7 |
* |
| 8 |
* This is not a complete driver, just low-level access routines for |
| 9 |
* the MAC controller itself. |
| 10 |
* |
| 11 |
* Based on the prism2 driver from Absolute Value Systems' linux-wlan |
| 12 |
* project, the Linux wvlan_cs driver, Lucent's HCF-Light |
| 13 |
* (wvlan_hcf.c) library, and the NetBSD wireless driver. |
| 14 |
* |
| 15 |
* Copyright (C) 2000, David Gibson, Linuxcare Australia <[email protected]> |
| 16 |
* |
| 17 |
* Portions taken from hfa384x.h, Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved. |
| 18 |
* |
| 19 |
* This file distributed under the GPL, version 2. |
| 20 |
*/ |
| 21 |
|
| 22 |
#ifndef _HERMES_H |
| 23 |
#define _HERMES_H |
| 24 |
|
| 25 |
/* Notes on locking: |
| 26 |
* |
| 27 |
* As a module of low level hardware access routines, there is no |
| 28 |
* locking. Users of this module should ensure that they serialize |
| 29 |
* access to the hermes_t structure, and to the hardware |
| 30 |
*/ |
| 31 |
|
| 32 |
#include <linux/delay.h> |
| 33 |
#include <linux/if_ether.h> |
| 34 |
#include <asm/byteorder.h> |
| 35 |
|
| 36 |
/* |
| 37 |
* Limits and constants |
| 38 |
*/ |
| 39 |
#define HERMES_ALLOC_LEN_MIN (4) |
| 40 |
#define HERMES_ALLOC_LEN_MAX (2400) |
| 41 |
#define HERMES_LTV_LEN_MAX (34) |
| 42 |
#define HERMES_BAP_DATALEN_MAX (4096) |
| 43 |
#define HERMES_BAP_OFFSET_MAX (4096) |
| 44 |
#define HERMES_PORTID_MAX (7) |
| 45 |
#define HERMES_NUMPORTS_MAX (HERMES_PORTID_MAX+1) |
| 46 |
#define HERMES_PDR_LEN_MAX (260) /* in bytes, from EK */ |
| 47 |
#define HERMES_PDA_RECS_MAX (200) /* a guess */ |
| 48 |
#define HERMES_PDA_LEN_MAX (1024) /* in bytes, from EK */ |
| 49 |
#define HERMES_SCANRESULT_MAX (35) |
| 50 |
#define HERMES_CHINFORESULT_MAX (8) |
| 51 |
#define HERMES_MAX_MULTICAST (16) |
| 52 |
#define HERMES_MAGIC (0x7d1f) |
| 53 |
|
| 54 |
/* |
| 55 |
* Hermes register offsets |
| 56 |
*/ |
| 57 |
#define HERMES_CMD (0x00) |
| 58 |
#define HERMES_PARAM0 (0x02) |
| 59 |
#define HERMES_PARAM1 (0x04) |
| 60 |
#define HERMES_PARAM2 (0x06) |
| 61 |
#define HERMES_STATUS (0x08) |
| 62 |
#define HERMES_RESP0 (0x0A) |
| 63 |
#define HERMES_RESP1 (0x0C) |
| 64 |
#define HERMES_RESP2 (0x0E) |
| 65 |
#define HERMES_INFOFID (0x10) |
| 66 |
#define HERMES_RXFID (0x20) |
| 67 |
#define HERMES_ALLOCFID (0x22) |
| 68 |
#define HERMES_TXCOMPLFID (0x24) |
| 69 |
#define HERMES_SELECT0 (0x18) |
| 70 |
#define HERMES_OFFSET0 (0x1C) |
| 71 |
#define HERMES_DATA0 (0x36) |
| 72 |
#define HERMES_SELECT1 (0x1A) |
| 73 |
#define HERMES_OFFSET1 (0x1E) |
| 74 |
#define HERMES_DATA1 (0x38) |
| 75 |
#define HERMES_EVSTAT (0x30) |
| 76 |
#define HERMES_INTEN (0x32) |
| 77 |
#define HERMES_EVACK (0x34) |
| 78 |
#define HERMES_CONTROL (0x14) |
| 79 |
#define HERMES_SWSUPPORT0 (0x28) |
| 80 |
#define HERMES_SWSUPPORT1 (0x2A) |
| 81 |
#define HERMES_SWSUPPORT2 (0x2C) |
| 82 |
#define HERMES_AUXPAGE (0x3A) |
| 83 |
#define HERMES_AUXOFFSET (0x3C) |
| 84 |
#define HERMES_AUXDATA (0x3E) |
| 85 |
|
| 86 |
/* |
| 87 |
* CMD register bitmasks |
| 88 |
*/ |
| 89 |
#define HERMES_CMD_BUSY (0x8000) |
| 90 |
#define HERMES_CMD_AINFO (0x7f00) |
| 91 |
#define HERMES_CMD_MACPORT (0x0700) |
| 92 |
#define HERMES_CMD_RECL (0x0100) |
| 93 |
#define HERMES_CMD_WRITE (0x0100) |
| 94 |
#define HERMES_CMD_PROGMODE (0x0300) |
| 95 |
#define HERMES_CMD_CMDCODE (0x003f) |
| 96 |
|
| 97 |
/* |
| 98 |
* STATUS register bitmasks |
| 99 |
*/ |
| 100 |
#define HERMES_STATUS_RESULT (0x7f00) |
| 101 |
#define HERMES_STATUS_CMDCODE (0x003f) |
| 102 |
|
| 103 |
/* |
| 104 |
* OFFSET register bitmasks |
| 105 |
*/ |
| 106 |
#define HERMES_OFFSET_BUSY (0x8000) |
| 107 |
#define HERMES_OFFSET_ERR (0x4000) |
| 108 |
#define HERMES_OFFSET_DATAOFF (0x0ffe) |
| 109 |
|
| 110 |
/* |
| 111 |
* Event register bitmasks (INTEN, EVSTAT, EVACK) |
| 112 |
*/ |
| 113 |
#define HERMES_EV_TICK (0x8000) |
| 114 |
#define HERMES_EV_WTERR (0x4000) |
| 115 |
#define HERMES_EV_INFDROP (0x2000) |
| 116 |
#define HERMES_EV_INFO (0x0080) |
| 117 |
#define HERMES_EV_DTIM (0x0020) |
| 118 |
#define HERMES_EV_CMD (0x0010) |
| 119 |
#define HERMES_EV_ALLOC (0x0008) |
| 120 |
#define HERMES_EV_TXEXC (0x0004) |
| 121 |
#define HERMES_EV_TX (0x0002) |
| 122 |
#define HERMES_EV_RX (0x0001) |
| 123 |
|
| 124 |
/* |
| 125 |
* Command codes |
| 126 |
*/ |
| 127 |
/*--- Controller Commands --------------------------*/ |
| 128 |
#define HERMES_CMD_INIT (0x0000) |
| 129 |
#define HERMES_CMD_ENABLE (0x0001) |
| 130 |
#define HERMES_CMD_DISABLE (0x0002) |
| 131 |
#define HERMES_CMD_DIAG (0x0003) |
| 132 |
|
| 133 |
/*--- Buffer Mgmt Commands --------------------------*/ |
| 134 |
#define HERMES_CMD_ALLOC (0x000A) |
| 135 |
#define HERMES_CMD_TX (0x000B) |
| 136 |
#define HERMES_CMD_CLRPRST (0x0012) |
| 137 |
|
| 138 |
/*--- Regulate Commands --------------------------*/ |
| 139 |
#define HERMES_CMD_NOTIFY (0x0010) |
| 140 |
#define HERMES_CMD_INQUIRE (0x0011) |
| 141 |
|
| 142 |
/*--- Configure Commands --------------------------*/ |
| 143 |
#define HERMES_CMD_ACCESS (0x0021) |
| 144 |
#define HERMES_CMD_DOWNLD (0x0022) |
| 145 |
|
| 146 |
/*--- Debugging Commands -----------------------------*/ |
| 147 |
#define HERMES_CMD_MONITOR (0x0038) |
| 148 |
#define HERMES_MONITOR_ENABLE (0x000b) |
| 149 |
#define HERMES_MONITOR_DISABLE (0x000f) |
| 150 |
|
| 151 |
/* |
| 152 |
* Frame structures and constants |
| 153 |
*/ |
| 154 |
|
| 155 |
#define HERMES_DESCRIPTOR_OFFSET 0 |
| 156 |
#define HERMES_802_11_OFFSET (14) |
| 157 |
#define HERMES_802_3_OFFSET (14+32) |
| 158 |
#define HERMES_802_2_OFFSET (14+32+14) |
| 159 |
|
| 160 |
struct hermes_rx_descriptor { |
| 161 |
u16 status; |
| 162 |
u32 time; |
| 163 |
u8 silence; |
| 164 |
u8 signal; |
| 165 |
u8 rate; |
| 166 |
u8 rxflow; |
| 167 |
u32 reserved; |
| 168 |
} __attribute__ ((packed)); |
| 169 |
|
| 170 |
#define HERMES_RXSTAT_ERR (0x0003) |
| 171 |
#define HERMES_RXSTAT_BADCRC (0x0001) |
| 172 |
#define HERMES_RXSTAT_UNDECRYPTABLE (0x0002) |
| 173 |
#define HERMES_RXSTAT_MACPORT (0x0700) |
| 174 |
#define HERMES_RXSTAT_PCF (0x1000) /* Frame was received in CF period */ |
| 175 |
#define HERMES_RXSTAT_MSGTYPE (0xE000) |
| 176 |
#define HERMES_RXSTAT_1042 (0x2000) /* RFC-1042 frame */ |
| 177 |
#define HERMES_RXSTAT_TUNNEL (0x4000) /* bridge-tunnel encoded frame */ |
| 178 |
#define HERMES_RXSTAT_WMP (0x6000) /* Wavelan-II Management Protocol frame */ |
| 179 |
|
| 180 |
struct hermes_tx_descriptor { |
| 181 |
u16 status; |
| 182 |
u16 reserved1; |
| 183 |
u16 reserved2; |
| 184 |
u32 sw_support; |
| 185 |
u8 retry_count; |
| 186 |
u8 tx_rate; |
| 187 |
u16 tx_control; |
| 188 |
} __attribute__ ((packed)); |
| 189 |
|
| 190 |
#define HERMES_TXSTAT_RETRYERR (0x0001) |
| 191 |
#define HERMES_TXSTAT_AGEDERR (0x0002) |
| 192 |
#define HERMES_TXSTAT_DISCON (0x0004) |
| 193 |
#define HERMES_TXSTAT_FORMERR (0x0008) |
| 194 |
|
| 195 |
#define HERMES_TXCTRL_TX_OK (0x0002) /* ?? interrupt on Tx complete */ |
| 196 |
#define HERMES_TXCTRL_TX_EX (0x0004) /* ?? interrupt on Tx exception */ |
| 197 |
#define HERMES_TXCTRL_802_11 (0x0008) /* We supply 802.11 header */ |
| 198 |
#define HERMES_TXCTRL_ALT_RTRY (0x0020) |
| 199 |
|
| 200 |
/* Inquiry constants and data types */ |
| 201 |
|
| 202 |
#define HERMES_INQ_TALLIES (0xF100) |
| 203 |
#define HERMES_INQ_SCAN (0xF101) |
| 204 |
#define HERMES_INQ_LINKSTATUS (0xF200) |
| 205 |
|
| 206 |
struct hermes_tallies_frame { |
| 207 |
u16 TxUnicastFrames; |
| 208 |
u16 TxMulticastFrames; |
| 209 |
u16 TxFragments; |
| 210 |
u16 TxUnicastOctets; |
| 211 |
u16 TxMulticastOctets; |
| 212 |
u16 TxDeferredTransmissions; |
| 213 |
u16 TxSingleRetryFrames; |
| 214 |
u16 TxMultipleRetryFrames; |
| 215 |
u16 TxRetryLimitExceeded; |
| 216 |
u16 TxDiscards; |
| 217 |
u16 RxUnicastFrames; |
| 218 |
u16 RxMulticastFrames; |
| 219 |
u16 RxFragments; |
| 220 |
u16 RxUnicastOctets; |
| 221 |
u16 RxMulticastOctets; |
| 222 |
u16 RxFCSErrors; |
| 223 |
u16 RxDiscards_NoBuffer; |
| 224 |
u16 TxDiscardsWrongSA; |
| 225 |
u16 RxWEPUndecryptable; |
| 226 |
u16 RxMsgInMsgFragments; |
| 227 |
u16 RxMsgInBadMsgFragments; |
| 228 |
/* Those last are probably not available in very old firmwares */ |
| 229 |
u16 RxDiscards_WEPICVError; |
| 230 |
u16 RxDiscards_WEPExcluded; |
| 231 |
} __attribute__ ((packed)); |
| 232 |
|
| 233 |
/* Grabbed from wlan-ng - Thanks Mark... - Jean II |
| 234 |
* This is the result of a scan inquiry command */ |
| 235 |
/* Structure describing info about an Access Point */ |
| 236 |
struct hermes_scan_apinfo { |
| 237 |
u16 channel; /* Channel where the AP sits */ |
| 238 |
u16 noise; /* Noise level */ |
| 239 |
u16 level; /* Signal level */ |
| 240 |
u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ |
| 241 |
u16 beacon_interv; /* Beacon interval ? */ |
| 242 |
u16 capabilities; /* Capabilities ? */ |
| 243 |
u8 essid[32]; /* ESSID of the network */ |
| 244 |
u8 rates[10]; /* Bit rate supported */ |
| 245 |
u16 proberesp_rate; /* ???? */ |
| 246 |
} __attribute__ ((packed)); |
| 247 |
/* Container */ |
| 248 |
struct hermes_scan_frame { |
| 249 |
u16 rsvd; /* ??? */ |
| 250 |
u16 scanreason; /* ??? */ |
| 251 |
struct hermes_scan_apinfo aps[35]; /* Scan result */ |
| 252 |
} __attribute__ ((packed)); |
| 253 |
#define HERMES_LINKSTATUS_NOT_CONNECTED (0x0000) |
| 254 |
#define HERMES_LINKSTATUS_CONNECTED (0x0001) |
| 255 |
#define HERMES_LINKSTATUS_DISCONNECTED (0x0002) |
| 256 |
#define HERMES_LINKSTATUS_AP_CHANGE (0x0003) |
| 257 |
#define HERMES_LINKSTATUS_AP_OUT_OF_RANGE (0x0004) |
| 258 |
#define HERMES_LINKSTATUS_AP_IN_RANGE (0x0005) |
| 259 |
#define HERMES_LINKSTATUS_ASSOC_FAILED (0x0006) |
| 260 |
|
| 261 |
struct hermes_linkstatus { |
| 262 |
u16 linkstatus; /* Link status */ |
| 263 |
} __attribute__ ((packed)); |
| 264 |
|
| 265 |
// #define HERMES_DEBUG_BUFFER 1 |
| 266 |
#define HERMES_DEBUG_BUFSIZE 4096 |
| 267 |
struct hermes_debug_entry { |
| 268 |
int bap; |
| 269 |
u16 id, offset; |
| 270 |
int cycles; |
| 271 |
}; |
| 272 |
|
| 273 |
#ifdef __KERNEL__ |
| 274 |
|
| 275 |
/* Timeouts */ |
| 276 |
#define HERMES_BAP_BUSY_TIMEOUT (500) /* In iterations of ~1us */ |
| 277 |
|
| 278 |
/* Basic control structure */ |
| 279 |
typedef struct hermes { |
| 280 |
unsigned long iobase; |
| 281 |
int io_space; /* 1 if we IO-mapped IO, 0 for memory-mapped IO? */ |
| 282 |
#define HERMES_IO 1 |
| 283 |
#define HERMES_MEM 0 |
| 284 |
int reg_spacing; |
| 285 |
#define HERMES_16BIT_REGSPACING 0 |
| 286 |
#define HERMES_32BIT_REGSPACING 1 |
| 287 |
|
| 288 |
u16 inten; /* Which interrupts should be enabled? */ |
| 289 |
|
| 290 |
#ifdef HERMES_DEBUG_BUFFER |
| 291 |
struct hermes_debug_entry dbuf[HERMES_DEBUG_BUFSIZE]; |
| 292 |
unsigned long dbufp; |
| 293 |
unsigned long profile[HERMES_BAP_BUSY_TIMEOUT+1]; |
| 294 |
#endif |
| 295 |
} hermes_t; |
| 296 |
|
| 297 |
typedef struct hermes_response { |
| 298 |
u16 status, resp0, resp1, resp2; |
| 299 |
} hermes_response_t; |
| 300 |
|
| 301 |
/* Register access convenience macros */ |
| 302 |
#define hermes_read_reg(hw, off) ((hw)->io_space ? \ |
| 303 |
inw((hw)->iobase + ( (off) << (hw)->reg_spacing )) : \ |
| 304 |
readw((hw)->iobase + ( (off) << (hw)->reg_spacing ))) |
| 305 |
#define hermes_write_reg(hw, off, val) ((hw)->io_space ? \ |
| 306 |
outw_p((val), (hw)->iobase + ( (off) << (hw)->reg_spacing )) : \ |
| 307 |
writew((val), (hw)->iobase + ( (off) << (hw)->reg_spacing ))) |
| 308 |
|
| 309 |
#define hermes_read_regn(hw, name) (hermes_read_reg((hw), HERMES_##name)) |
| 310 |
#define hermes_write_regn(hw, name, val) (hermes_write_reg((hw), HERMES_##name, (val))) |
| 311 |
|
| 312 |
/* Function prototypes */ |
| 313 |
void hermes_struct_init(hermes_t *hw, ulong address, int io_space, int reg_spacing); |
| 314 |
int hermes_init(hermes_t *hw); |
| 315 |
int hermes_docmd_wait(hermes_t *hw, u16 cmd, u16 parm0, hermes_response_t *resp); |
| 316 |
int hermes_allocate(hermes_t *hw, u16 size, u16 *fid); |
| 317 |
|
| 318 |
int hermes_bap_pread(hermes_t *hw, int bap, void *buf, unsigned len, |
| 319 |
u16 id, u16 offset); |
| 320 |
int hermes_bap_pwrite(hermes_t *hw, int bap, const void *buf, unsigned len, |
| 321 |
u16 id, u16 offset); |
| 322 |
int hermes_read_ltv(hermes_t *hw, int bap, u16 rid, unsigned buflen, |
| 323 |
u16 *length, void *buf); |
| 324 |
int hermes_write_ltv(hermes_t *hw, int bap, u16 rid, |
| 325 |
u16 length, const void *value); |
| 326 |
|
| 327 |
/* Inline functions */ |
| 328 |
|
| 329 |
static inline int hermes_present(hermes_t *hw) |
| 330 |
{ |
| 331 |
return hermes_read_regn(hw, SWSUPPORT0) == HERMES_MAGIC; |
| 332 |
} |
| 333 |
|
| 334 |
static inline void hermes_set_irqmask(hermes_t *hw, u16 events) |
| 335 |
{ |
| 336 |
hw->inten = events; |
| 337 |
hermes_write_regn(hw, INTEN, events); |
| 338 |
} |
| 339 |
|
| 340 |
static inline int hermes_enable_port(hermes_t *hw, int port) |
| 341 |
{ |
| 342 |
return hermes_docmd_wait(hw, HERMES_CMD_ENABLE | (port << 8), |
| 343 |
0, NULL); |
| 344 |
} |
| 345 |
|
| 346 |
static inline int hermes_disable_port(hermes_t *hw, int port) |
| 347 |
{ |
| 348 |
return hermes_docmd_wait(hw, HERMES_CMD_DISABLE | (port << 8), |
| 349 |
0, NULL); |
| 350 |
} |
| 351 |
|
| 352 |
/* Initiate an INQUIRE command (tallies or scan). The result will come as an |
| 353 |
* information frame in __orinoco_ev_info() */ |
| 354 |
static inline int hermes_inquire(hermes_t *hw, u16 rid) |
| 355 |
{ |
| 356 |
return hermes_docmd_wait(hw, HERMES_CMD_INQUIRE, rid, NULL); |
| 357 |
} |
| 358 |
|
| 359 |
#define HERMES_BYTES_TO_RECLEN(n) ( (((n)+1)/2) + 1 ) |
| 360 |
#define HERMES_RECLEN_TO_BYTES(n) ( ((n)-1) * 2 ) |
| 361 |
|
| 362 |
/* Note that for the next two, the count is in 16-bit words, not bytes */ |
| 363 |
static inline void hermes_read_words(struct hermes *hw, int off, void *buf, unsigned count) |
| 364 |
{ |
| 365 |
off = off << hw->reg_spacing;; |
| 366 |
|
| 367 |
if (hw->io_space) { |
| 368 |
insw(hw->iobase + off, buf, count); |
| 369 |
} else { |
| 370 |
unsigned i; |
| 371 |
u16 *p; |
| 372 |
|
| 373 |
/* This needs to *not* byteswap (like insw()) but |
| 374 |
* readw() does byteswap hence the conversion. I hope |
| 375 |
* gcc is smart enough to fold away the two swaps on |
| 376 |
* big-endian platforms. */ |
| 377 |
for (i = 0, p = buf; i < count; i++) { |
| 378 |
*p++ = cpu_to_le16(readw(hw->iobase + off)); |
| 379 |
} |
| 380 |
} |
| 381 |
} |
| 382 |
|
| 383 |
static inline void hermes_write_words(struct hermes *hw, int off, const void *buf, unsigned count) |
| 384 |
{ |
| 385 |
off = off << hw->reg_spacing;; |
| 386 |
|
| 387 |
if (hw->io_space) { |
| 388 |
outsw(hw->iobase + off, buf, count); |
| 389 |
} else { |
| 390 |
unsigned i; |
| 391 |
const u16 *p; |
| 392 |
|
| 393 |
/* This needs to *not* byteswap (like outsw()) but |
| 394 |
* writew() does byteswap hence the conversion. I |
| 395 |
* hope gcc is smart enough to fold away the two swaps |
| 396 |
* on big-endian platforms. */ |
| 397 |
for (i = 0, p = buf; i < count; i++) { |
| 398 |
writew(le16_to_cpu(*p++), hw->iobase + off); |
| 399 |
} |
| 400 |
} |
| 401 |
} |
| 402 |
|
| 403 |
static inline void hermes_clear_words(struct hermes *hw, int off, unsigned count) |
| 404 |
{ |
| 405 |
unsigned i; |
| 406 |
|
| 407 |
off = off << hw->reg_spacing;; |
| 408 |
|
| 409 |
if (hw->io_space) { |
| 410 |
for (i = 0; i < count; i++) |
| 411 |
outw(0, hw->iobase + off); |
| 412 |
} else { |
| 413 |
for (i = 0; i < count; i++) |
| 414 |
writew(0, hw->iobase + off); |
| 415 |
} |
| 416 |
} |
| 417 |
|
| 418 |
#define HERMES_READ_RECORD(hw, bap, rid, buf) \ |
| 419 |
(hermes_read_ltv((hw),(bap),(rid), sizeof(*buf), NULL, (buf))) |
| 420 |
#define HERMES_WRITE_RECORD(hw, bap, rid, buf) \ |
| 421 |
(hermes_write_ltv((hw),(bap),(rid),HERMES_BYTES_TO_RECLEN(sizeof(*buf)),(buf))) |
| 422 |
|
| 423 |
static inline int hermes_read_wordrec(hermes_t *hw, int bap, u16 rid, u16 *word) |
| 424 |
{ |
| 425 |
u16 rec; |
| 426 |
int err; |
| 427 |
|
| 428 |
err = HERMES_READ_RECORD(hw, bap, rid, &rec); |
| 429 |
*word = le16_to_cpu(rec); |
| 430 |
return err; |
| 431 |
} |
| 432 |
|
| 433 |
static inline int hermes_write_wordrec(hermes_t *hw, int bap, u16 rid, u16 word) |
| 434 |
{ |
| 435 |
u16 rec = cpu_to_le16(word); |
| 436 |
return HERMES_WRITE_RECORD(hw, bap, rid, &rec); |
| 437 |
} |
| 438 |
|
| 439 |
#else /* ! __KERNEL__ */ |
| 440 |
|
| 441 |
/* These are provided for the benefit of userspace drivers and testing programs |
| 442 |
which use ioperm() or iopl() */ |
| 443 |
|
| 444 |
#define hermes_read_reg(base, off) (inw((base) + (off))) |
| 445 |
#define hermes_write_reg(base, off, val) (outw((val), (base) + (off))) |
| 446 |
|
| 447 |
#define hermes_read_regn(base, name) (hermes_read_reg((base), HERMES_##name)) |
| 448 |
#define hermes_write_regn(base, name, val) (hermes_write_reg((base), HERMES_##name, (val))) |
| 449 |
|
| 450 |
/* Note that for the next two, the count is in 16-bit words, not bytes */ |
| 451 |
#define hermes_read_data(base, off, buf, count) (insw((base) + (off), (buf), (count))) |
| 452 |
#define hermes_write_data(base, off, buf, count) (outsw((base) + (off), (buf), (count))) |
| 453 |
|
| 454 |
#endif /* ! __KERNEL__ */ |
| 455 |
|
| 456 |
#endif /* _HERMES_H */ |