| 1 |
/* hermes.c |
| 2 |
* |
| 3 |
* Driver core for the "Hermes" wireless MAC controller, as used in |
| 4 |
* the Lucent Orinoco and Cabletron RoamAbout cards. It should also |
| 5 |
* work on the hfa3841 and hfa3842 MAC controller chips used in the |
| 6 |
* Prism II chipsets. |
| 7 |
* |
| 8 |
* This is not a complete driver, just low-level access routines for |
| 9 |
* the MAC controller itself. |
| 10 |
* |
| 11 |
* Based on the prism2 driver from Absolute Value Systems' linux-wlan |
| 12 |
* project, the Linux wvlan_cs driver, Lucent's HCF-Light |
| 13 |
* (wvlan_hcf.c) library, and the NetBSD wireless driver (in no |
| 14 |
* particular order). |
| 15 |
* |
| 16 |
* Copyright (C) 2000, David Gibson, Linuxcare Australia <[email protected]> |
| 17 |
* Copyright (C) 2001, David Gibson, IBM <[email protected]> |
| 18 |
* |
| 19 |
* The contents of this file are subject to the Mozilla Public License |
| 20 |
* Version 1.1 (the "License"); you may not use this file except in |
| 21 |
* compliance with the License. You may obtain a copy of the License |
| 22 |
* at http://www.mozilla.org/MPL/ |
| 23 |
* |
| 24 |
* Software distributed under the License is distributed on an "AS IS" |
| 25 |
* basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See |
| 26 |
* the License for the specific language governing rights and |
| 27 |
* limitations under the License. |
| 28 |
* |
| 29 |
* Alternatively, the contents of this file may be used under the |
| 30 |
* terms of the GNU General Public License version 2 (the "GPL"), in |
| 31 |
* which case the provisions of the GPL are applicable instead of the |
| 32 |
* above. If you wish to allow the use of your version of this file |
| 33 |
* only under the terms of the GPL and not to allow others to use your |
| 34 |
* version of this file under the MPL, indicate your decision by |
| 35 |
* deleting the provisions above and replace them with the notice and |
| 36 |
* other provisions required by the GPL. If you do not delete the |
| 37 |
* provisions above, a recipient may use your version of this file |
| 38 |
* under either the MPL or the GPL. |
| 39 |
*/ |
| 40 |
|
| 41 |
#include <linux/config.h> |
| 42 |
|
| 43 |
#include <linux/module.h> |
| 44 |
#include <linux/types.h> |
| 45 |
#include <linux/threads.h> |
| 46 |
#include <linux/smp.h> |
| 47 |
#include <asm/io.h> |
| 48 |
#include <linux/delay.h> |
| 49 |
#include <linux/init.h> |
| 50 |
#include <linux/kernel.h> |
| 51 |
#include <asm/errno.h> |
| 52 |
|
| 53 |
#include "hermes.h" |
| 54 |
|
| 55 |
MODULE_DESCRIPTION("Low-level driver helper for Lucent Hermes chipset and Prism II HFA384x wireless MAC controller"); |
| 56 |
MODULE_AUTHOR("David Gibson <[email protected]>"); |
| 57 |
#ifdef MODULE_LICENSE |
| 58 |
MODULE_LICENSE("Dual MPL/GPL"); |
| 59 |
#endif |
| 60 |
|
| 61 |
/* These are maximum timeouts. Most often, card wil react much faster */ |
| 62 |
#define CMD_BUSY_TIMEOUT (100) /* In iterations of ~1us */ |
| 63 |
#define CMD_INIT_TIMEOUT (50000) /* in iterations of ~10us */ |
| 64 |
#define CMD_COMPL_TIMEOUT (20000) /* in iterations of ~10us */ |
| 65 |
#define ALLOC_COMPL_TIMEOUT (1000) /* in iterations of ~10us */ |
| 66 |
|
| 67 |
/* |
| 68 |
* Debugging helpers |
| 69 |
*/ |
| 70 |
|
| 71 |
#define IO_TYPE(hw) ((hw)->io_space ? "IO " : "MEM ") |
| 72 |
#define DMSG(stuff...) do {printk(KERN_DEBUG "hermes @ %s0x%x: " , IO_TYPE(hw), hw->iobase); \ |
| 73 |
printk(stuff);} while (0) |
| 74 |
|
| 75 |
#undef HERMES_DEBUG |
| 76 |
#ifdef HERMES_DEBUG |
| 77 |
#include <stdarg.h> |
| 78 |
|
| 79 |
#define DEBUG(lvl, stuff...) if ( (lvl) <= HERMES_DEBUG) DMSG(stuff) |
| 80 |
|
| 81 |
#else /* ! HERMES_DEBUG */ |
| 82 |
|
| 83 |
#define DEBUG(lvl, stuff...) do { } while (0) |
| 84 |
|
| 85 |
#endif /* ! HERMES_DEBUG */ |
| 86 |
|
| 87 |
|
| 88 |
/* |
| 89 |
* Internal functions |
| 90 |
*/ |
| 91 |
|
| 92 |
/* Issue a command to the chip. Waiting for it to complete is the caller's |
| 93 |
problem. |
| 94 |
|
| 95 |
Returns -EBUSY if the command register is busy, 0 on success. |
| 96 |
|
| 97 |
Callable from any context. |
| 98 |
*/ |
| 99 |
static int hermes_issue_cmd(hermes_t *hw, u16 cmd, u16 param0) |
| 100 |
{ |
| 101 |
int k = CMD_BUSY_TIMEOUT; |
| 102 |
u16 reg; |
| 103 |
|
| 104 |
/* First wait for the command register to unbusy */ |
| 105 |
reg = hermes_read_regn(hw, CMD); |
| 106 |
while ( (reg & HERMES_CMD_BUSY) && k ) { |
| 107 |
k--; |
| 108 |
udelay(1); |
| 109 |
reg = hermes_read_regn(hw, CMD); |
| 110 |
} |
| 111 |
if (reg & HERMES_CMD_BUSY) { |
| 112 |
return -EBUSY; |
| 113 |
} |
| 114 |
|
| 115 |
hermes_write_regn(hw, PARAM2, 0); |
| 116 |
hermes_write_regn(hw, PARAM1, 0); |
| 117 |
hermes_write_regn(hw, PARAM0, param0); |
| 118 |
hermes_write_regn(hw, CMD, cmd); |
| 119 |
|
| 120 |
return 0; |
| 121 |
} |
| 122 |
|
| 123 |
/* |
| 124 |
* Function definitions |
| 125 |
*/ |
| 126 |
|
| 127 |
void hermes_struct_init(hermes_t *hw, ulong address, |
| 128 |
int io_space, int reg_spacing) |
| 129 |
{ |
| 130 |
hw->iobase = address; |
| 131 |
hw->io_space = io_space; |
| 132 |
hw->reg_spacing = reg_spacing; |
| 133 |
hw->inten = 0x0; |
| 134 |
|
| 135 |
#ifdef HERMES_DEBUG_BUFFER |
| 136 |
hw->dbufp = 0; |
| 137 |
memset(&hw->dbuf, 0xff, sizeof(hw->dbuf)); |
| 138 |
memset(&hw->profile, 0, sizeof(hw->profile)); |
| 139 |
#endif |
| 140 |
} |
| 141 |
|
| 142 |
int hermes_init(hermes_t *hw) |
| 143 |
{ |
| 144 |
u16 status, reg; |
| 145 |
int err = 0; |
| 146 |
int k; |
| 147 |
|
| 148 |
/* We don't want to be interrupted while resetting the chipset */ |
| 149 |
hw->inten = 0x0; |
| 150 |
hermes_write_regn(hw, INTEN, 0); |
| 151 |
hermes_write_regn(hw, EVACK, 0xffff); |
| 152 |
|
| 153 |
/* Normally it's a "can't happen" for the command register to |
| 154 |
be busy when we go to issue a command because we are |
| 155 |
serializing all commands. However we want to have some |
| 156 |
chance of resetting the card even if it gets into a stupid |
| 157 |
state, so we actually wait to see if the command register |
| 158 |
will unbusy itself here. */ |
| 159 |
k = CMD_BUSY_TIMEOUT; |
| 160 |
reg = hermes_read_regn(hw, CMD); |
| 161 |
while (k && (reg & HERMES_CMD_BUSY)) { |
| 162 |
if (reg == 0xffff) /* Special case - the card has probably been removed, |
| 163 |
so don't wait for the timeout */ |
| 164 |
return -ENODEV; |
| 165 |
|
| 166 |
k--; |
| 167 |
udelay(1); |
| 168 |
reg = hermes_read_regn(hw, CMD); |
| 169 |
} |
| 170 |
|
| 171 |
/* No need to explicitly handle the timeout - if we've timed |
| 172 |
out hermes_issue_cmd() will probably return -EBUSY below */ |
| 173 |
|
| 174 |
/* According to the documentation, EVSTAT may contain |
| 175 |
obsolete event occurrence information. We have to acknowledge |
| 176 |
it by writing EVACK. */ |
| 177 |
reg = hermes_read_regn(hw, EVSTAT); |
| 178 |
hermes_write_regn(hw, EVACK, reg); |
| 179 |
|
| 180 |
/* We don't use hermes_docmd_wait here, because the reset wipes |
| 181 |
the magic constant in SWSUPPORT0 away, and it gets confused */ |
| 182 |
err = hermes_issue_cmd(hw, HERMES_CMD_INIT, 0); |
| 183 |
if (err) |
| 184 |
return err; |
| 185 |
|
| 186 |
reg = hermes_read_regn(hw, EVSTAT); |
| 187 |
k = CMD_INIT_TIMEOUT; |
| 188 |
while ( (! (reg & HERMES_EV_CMD)) && k) { |
| 189 |
k--; |
| 190 |
udelay(10); |
| 191 |
reg = hermes_read_regn(hw, EVSTAT); |
| 192 |
} |
| 193 |
|
| 194 |
hermes_write_regn(hw, SWSUPPORT0, HERMES_MAGIC); |
| 195 |
|
| 196 |
if (! hermes_present(hw)) { |
| 197 |
DEBUG(0, "hermes @ 0x%x: Card removed during reset.\n", |
| 198 |
hw->iobase); |
| 199 |
err = -ENODEV; |
| 200 |
goto out; |
| 201 |
} |
| 202 |
|
| 203 |
if (! (reg & HERMES_EV_CMD)) { |
| 204 |
printk(KERN_ERR "hermes @ %s0x%lx: " |
| 205 |
"Timeout waiting for card to reset (reg=0x%04x)!\n", |
| 206 |
IO_TYPE(hw), hw->iobase, reg); |
| 207 |
err = -ETIMEDOUT; |
| 208 |
goto out; |
| 209 |
} |
| 210 |
|
| 211 |
status = hermes_read_regn(hw, STATUS); |
| 212 |
|
| 213 |
hermes_write_regn(hw, EVACK, HERMES_EV_CMD); |
| 214 |
|
| 215 |
if (status & HERMES_STATUS_RESULT) |
| 216 |
err = -EIO; |
| 217 |
|
| 218 |
out: |
| 219 |
return err; |
| 220 |
} |
| 221 |
|
| 222 |
/* Issue a command to the chip, and (busy!) wait for it to |
| 223 |
* complete. |
| 224 |
* |
| 225 |
* Returns: < 0 on internal error, 0 on success, > 0 on error returned by the firmware |
| 226 |
* |
| 227 |
* Callable from any context, but locking is your problem. */ |
| 228 |
int hermes_docmd_wait(hermes_t *hw, u16 cmd, u16 parm0, |
| 229 |
hermes_response_t *resp) |
| 230 |
{ |
| 231 |
int err; |
| 232 |
int k; |
| 233 |
u16 reg; |
| 234 |
u16 status; |
| 235 |
|
| 236 |
err = hermes_issue_cmd(hw, cmd, parm0); |
| 237 |
if (err) { |
| 238 |
if (! hermes_present(hw)) { |
| 239 |
printk(KERN_WARNING "hermes @ %s0x%lx: " |
| 240 |
"Card removed while issuing command.\n", |
| 241 |
IO_TYPE(hw), hw->iobase); |
| 242 |
err = -ENODEV; |
| 243 |
} else |
| 244 |
printk(KERN_ERR "hermes @ %s0x%lx: Error %d issuing command.\n", |
| 245 |
IO_TYPE(hw), hw->iobase, err); |
| 246 |
goto out; |
| 247 |
} |
| 248 |
|
| 249 |
reg = hermes_read_regn(hw, EVSTAT); |
| 250 |
k = CMD_COMPL_TIMEOUT; |
| 251 |
while ( (! (reg & HERMES_EV_CMD)) && k) { |
| 252 |
k--; |
| 253 |
udelay(10); |
| 254 |
reg = hermes_read_regn(hw, EVSTAT); |
| 255 |
} |
| 256 |
|
| 257 |
if (! hermes_present(hw)) { |
| 258 |
printk(KERN_WARNING "hermes @ %s0x%lx: " |
| 259 |
"Card removed while waiting for command completion.\n", |
| 260 |
IO_TYPE(hw), hw->iobase); |
| 261 |
err = -ENODEV; |
| 262 |
goto out; |
| 263 |
} |
| 264 |
|
| 265 |
if (! (reg & HERMES_EV_CMD)) { |
| 266 |
printk(KERN_ERR "hermes @ %s0x%lx: " |
| 267 |
"Timeout waiting for command completion.\n", |
| 268 |
IO_TYPE(hw), hw->iobase); |
| 269 |
err = -ETIMEDOUT; |
| 270 |
goto out; |
| 271 |
} |
| 272 |
|
| 273 |
status = hermes_read_regn(hw, STATUS); |
| 274 |
if (resp) { |
| 275 |
resp->status = status; |
| 276 |
resp->resp0 = hermes_read_regn(hw, RESP0); |
| 277 |
resp->resp1 = hermes_read_regn(hw, RESP1); |
| 278 |
resp->resp2 = hermes_read_regn(hw, RESP2); |
| 279 |
} |
| 280 |
|
| 281 |
hermes_write_regn(hw, EVACK, HERMES_EV_CMD); |
| 282 |
|
| 283 |
if (status & HERMES_STATUS_RESULT) |
| 284 |
err = -EIO; |
| 285 |
|
| 286 |
out: |
| 287 |
return err; |
| 288 |
} |
| 289 |
|
| 290 |
int hermes_allocate(hermes_t *hw, u16 size, u16 *fid) |
| 291 |
{ |
| 292 |
int err = 0; |
| 293 |
int k; |
| 294 |
u16 reg; |
| 295 |
|
| 296 |
if ( (size < HERMES_ALLOC_LEN_MIN) || (size > HERMES_ALLOC_LEN_MAX) ) |
| 297 |
return -EINVAL; |
| 298 |
|
| 299 |
err = hermes_docmd_wait(hw, HERMES_CMD_ALLOC, size, NULL); |
| 300 |
if (err) { |
| 301 |
return err; |
| 302 |
} |
| 303 |
|
| 304 |
reg = hermes_read_regn(hw, EVSTAT); |
| 305 |
k = ALLOC_COMPL_TIMEOUT; |
| 306 |
while ( (! (reg & HERMES_EV_ALLOC)) && k) { |
| 307 |
k--; |
| 308 |
udelay(10); |
| 309 |
reg = hermes_read_regn(hw, EVSTAT); |
| 310 |
} |
| 311 |
|
| 312 |
if (! hermes_present(hw)) { |
| 313 |
printk(KERN_WARNING "hermes @ %s0x%lx: " |
| 314 |
"Card removed waiting for frame allocation.\n", |
| 315 |
IO_TYPE(hw), hw->iobase); |
| 316 |
return -ENODEV; |
| 317 |
} |
| 318 |
|
| 319 |
if (! (reg & HERMES_EV_ALLOC)) { |
| 320 |
printk(KERN_ERR "hermes @ %s0x%lx: " |
| 321 |
"Timeout waiting for frame allocation\n", |
| 322 |
IO_TYPE(hw), hw->iobase); |
| 323 |
return -ETIMEDOUT; |
| 324 |
} |
| 325 |
|
| 326 |
*fid = hermes_read_regn(hw, ALLOCFID); |
| 327 |
hermes_write_regn(hw, EVACK, HERMES_EV_ALLOC); |
| 328 |
|
| 329 |
return 0; |
| 330 |
} |
| 331 |
|
| 332 |
|
| 333 |
/* Set up a BAP to read a particular chunk of data from card's internal buffer. |
| 334 |
* |
| 335 |
* Returns: < 0 on internal failure (errno), 0 on success, >0 on error |
| 336 |
* from firmware |
| 337 |
* |
| 338 |
* Callable from any context */ |
| 339 |
static int hermes_bap_seek(hermes_t *hw, int bap, u16 id, u16 offset) |
| 340 |
{ |
| 341 |
int sreg = bap ? HERMES_SELECT1 : HERMES_SELECT0; |
| 342 |
int oreg = bap ? HERMES_OFFSET1 : HERMES_OFFSET0; |
| 343 |
int k; |
| 344 |
u16 reg; |
| 345 |
|
| 346 |
/* Paranoia.. */ |
| 347 |
if ( (offset > HERMES_BAP_OFFSET_MAX) || (offset % 2) ) |
| 348 |
return -EINVAL; |
| 349 |
|
| 350 |
k = HERMES_BAP_BUSY_TIMEOUT; |
| 351 |
reg = hermes_read_reg(hw, oreg); |
| 352 |
while ((reg & HERMES_OFFSET_BUSY) && k) { |
| 353 |
k--; |
| 354 |
udelay(1); |
| 355 |
reg = hermes_read_reg(hw, oreg); |
| 356 |
} |
| 357 |
|
| 358 |
#ifdef HERMES_DEBUG_BUFFER |
| 359 |
hw->profile[HERMES_BAP_BUSY_TIMEOUT - k]++; |
| 360 |
|
| 361 |
if (k < HERMES_BAP_BUSY_TIMEOUT) { |
| 362 |
struct hermes_debug_entry *e = |
| 363 |
&hw->dbuf[(hw->dbufp++) % HERMES_DEBUG_BUFSIZE]; |
| 364 |
e->bap = bap; |
| 365 |
e->id = id; |
| 366 |
e->offset = offset; |
| 367 |
e->cycles = HERMES_BAP_BUSY_TIMEOUT - k; |
| 368 |
} |
| 369 |
#endif |
| 370 |
|
| 371 |
if (reg & HERMES_OFFSET_BUSY) |
| 372 |
return -ETIMEDOUT; |
| 373 |
|
| 374 |
/* Now we actually set up the transfer */ |
| 375 |
hermes_write_reg(hw, sreg, id); |
| 376 |
hermes_write_reg(hw, oreg, offset); |
| 377 |
|
| 378 |
/* Wait for the BAP to be ready */ |
| 379 |
k = HERMES_BAP_BUSY_TIMEOUT; |
| 380 |
reg = hermes_read_reg(hw, oreg); |
| 381 |
while ( (reg & (HERMES_OFFSET_BUSY | HERMES_OFFSET_ERR)) && k) { |
| 382 |
k--; |
| 383 |
udelay(1); |
| 384 |
reg = hermes_read_reg(hw, oreg); |
| 385 |
} |
| 386 |
|
| 387 |
if (reg & HERMES_OFFSET_BUSY) { |
| 388 |
return -ETIMEDOUT; |
| 389 |
} |
| 390 |
|
| 391 |
if (reg & HERMES_OFFSET_ERR) { |
| 392 |
return -EIO; |
| 393 |
} |
| 394 |
|
| 395 |
|
| 396 |
return 0; |
| 397 |
} |
| 398 |
|
| 399 |
/* Read a block of data from the chip's buffer, via the |
| 400 |
* BAP. Synchronization/serialization is the caller's problem. len |
| 401 |
* must be even. |
| 402 |
* |
| 403 |
* Returns: < 0 on internal failure (errno), 0 on success, > 0 on error from firmware |
| 404 |
*/ |
| 405 |
int hermes_bap_pread(hermes_t *hw, int bap, void *buf, unsigned len, |
| 406 |
u16 id, u16 offset) |
| 407 |
{ |
| 408 |
int dreg = bap ? HERMES_DATA1 : HERMES_DATA0; |
| 409 |
int err = 0; |
| 410 |
|
| 411 |
if ( (len < 0) || (len % 2) ) |
| 412 |
return -EINVAL; |
| 413 |
|
| 414 |
err = hermes_bap_seek(hw, bap, id, offset); |
| 415 |
if (err) |
| 416 |
goto out; |
| 417 |
|
| 418 |
/* Actually do the transfer */ |
| 419 |
hermes_read_words(hw, dreg, buf, len/2); |
| 420 |
|
| 421 |
out: |
| 422 |
return err; |
| 423 |
} |
| 424 |
|
| 425 |
/* Write a block of data to the chip's buffer, via the |
| 426 |
* BAP. Synchronization/serialization is the caller's problem. len |
| 427 |
* must be even. |
| 428 |
* |
| 429 |
* Returns: < 0 on internal failure (errno), 0 on success, > 0 on error from firmware |
| 430 |
*/ |
| 431 |
int hermes_bap_pwrite(hermes_t *hw, int bap, const void *buf, unsigned len, |
| 432 |
u16 id, u16 offset) |
| 433 |
{ |
| 434 |
int dreg = bap ? HERMES_DATA1 : HERMES_DATA0; |
| 435 |
int err = 0; |
| 436 |
|
| 437 |
if ( (len < 0) || (len % 2) ) |
| 438 |
return -EINVAL; |
| 439 |
|
| 440 |
err = hermes_bap_seek(hw, bap, id, offset); |
| 441 |
if (err) |
| 442 |
goto out; |
| 443 |
|
| 444 |
/* Actually do the transfer */ |
| 445 |
hermes_write_words(hw, dreg, buf, len/2); |
| 446 |
|
| 447 |
out: |
| 448 |
return err; |
| 449 |
} |
| 450 |
|
| 451 |
/* Read a Length-Type-Value record from the card. |
| 452 |
* |
| 453 |
* If length is NULL, we ignore the length read from the card, and |
| 454 |
* read the entire buffer regardless. This is useful because some of |
| 455 |
* the configuration records appear to have incorrect lengths in |
| 456 |
* practice. |
| 457 |
* |
| 458 |
* Callable from user or bh context. */ |
| 459 |
int hermes_read_ltv(hermes_t *hw, int bap, u16 rid, unsigned bufsize, |
| 460 |
u16 *length, void *buf) |
| 461 |
{ |
| 462 |
int err = 0; |
| 463 |
int dreg = bap ? HERMES_DATA1 : HERMES_DATA0; |
| 464 |
u16 rlength, rtype; |
| 465 |
unsigned nwords; |
| 466 |
|
| 467 |
if ( (bufsize < 0) || (bufsize % 2) ) |
| 468 |
return -EINVAL; |
| 469 |
|
| 470 |
err = hermes_docmd_wait(hw, HERMES_CMD_ACCESS, rid, NULL); |
| 471 |
if (err) |
| 472 |
return err; |
| 473 |
|
| 474 |
err = hermes_bap_seek(hw, bap, rid, 0); |
| 475 |
if (err) |
| 476 |
return err; |
| 477 |
|
| 478 |
rlength = hermes_read_reg(hw, dreg); |
| 479 |
|
| 480 |
if (! rlength) |
| 481 |
return -ENOENT; |
| 482 |
|
| 483 |
rtype = hermes_read_reg(hw, dreg); |
| 484 |
|
| 485 |
if (length) |
| 486 |
*length = rlength; |
| 487 |
|
| 488 |
if (rtype != rid) |
| 489 |
printk(KERN_WARNING "hermes @ %s0x%lx: " |
| 490 |
"hermes_read_ltv(): rid (0x%04x) does not match type (0x%04x)\n", |
| 491 |
IO_TYPE(hw), hw->iobase, rid, rtype); |
| 492 |
if (HERMES_RECLEN_TO_BYTES(rlength) > bufsize) |
| 493 |
printk(KERN_WARNING "hermes @ %s0x%lx: " |
| 494 |
"Truncating LTV record from %d to %d bytes. " |
| 495 |
"(rid=0x%04x, len=0x%04x)\n", |
| 496 |
IO_TYPE(hw), hw->iobase, |
| 497 |
HERMES_RECLEN_TO_BYTES(rlength), bufsize, rid, rlength); |
| 498 |
|
| 499 |
nwords = min((unsigned)rlength - 1, bufsize / 2); |
| 500 |
hermes_read_words(hw, dreg, buf, nwords); |
| 501 |
|
| 502 |
return 0; |
| 503 |
} |
| 504 |
|
| 505 |
int hermes_write_ltv(hermes_t *hw, int bap, u16 rid, |
| 506 |
u16 length, const void *value) |
| 507 |
{ |
| 508 |
int dreg = bap ? HERMES_DATA1 : HERMES_DATA0; |
| 509 |
int err = 0; |
| 510 |
unsigned count; |
| 511 |
|
| 512 |
if (length == 0) |
| 513 |
return -EINVAL; |
| 514 |
|
| 515 |
err = hermes_bap_seek(hw, bap, rid, 0); |
| 516 |
if (err) |
| 517 |
return err; |
| 518 |
|
| 519 |
hermes_write_reg(hw, dreg, length); |
| 520 |
hermes_write_reg(hw, dreg, rid); |
| 521 |
|
| 522 |
count = length - 1; |
| 523 |
|
| 524 |
hermes_write_words(hw, dreg, value, count); |
| 525 |
|
| 526 |
err = hermes_docmd_wait(hw, HERMES_CMD_ACCESS | HERMES_CMD_WRITE, |
| 527 |
rid, NULL); |
| 528 |
|
| 529 |
return err; |
| 530 |
} |
| 531 |
|
| 532 |
EXPORT_SYMBOL(hermes_struct_init); |
| 533 |
EXPORT_SYMBOL(hermes_init); |
| 534 |
EXPORT_SYMBOL(hermes_docmd_wait); |
| 535 |
EXPORT_SYMBOL(hermes_allocate); |
| 536 |
|
| 537 |
EXPORT_SYMBOL(hermes_bap_pread); |
| 538 |
EXPORT_SYMBOL(hermes_bap_pwrite); |
| 539 |
EXPORT_SYMBOL(hermes_read_ltv); |
| 540 |
EXPORT_SYMBOL(hermes_write_ltv); |
| 541 |
|
| 542 |
static int __init init_hermes(void) |
| 543 |
{ |
| 544 |
return 0; |
| 545 |
} |
| 546 |
|
| 547 |
static void __exit exit_hermes(void) |
| 548 |
{ |
| 549 |
} |
| 550 |
|
| 551 |
module_init(init_hermes); |
| 552 |
module_exit(exit_hermes); |