| 1 |
\chapter{Supported Tape Drives} |
| 2 |
\label{blb:SupportedDrives} |
| 3 |
\index[general]{Drives!Supported Tape } |
| 4 |
\index[general]{Supported Tape Drives } |
| 5 |
|
| 6 |
\bacula{} uses standard operating system calls (\texttt{read}, \texttt{write}, \texttt{ioctl}) to |
| 7 |
interface to tape drives. As a consequence, it relies on having a |
| 8 |
correctly written \acs{OS} tape driver. \bacula{} is known to work perfectly well |
| 9 |
with \acs{SCSI} tape drivers on FreeBSD, Linux, Solaris, and Windows machines, |
| 10 |
and it may work on other *nix machines. |
| 11 |
|
| 12 |
Recently there are many new drives that use IDE, ATAPI, or |
| 13 |
SATA interfaces rather than \acs{SCSI}. On Linux the OnStream drive, which uses |
| 14 |
the OSST driver is one such |
| 15 |
example, and it is known to work with \bacula{}. In addition a number of such |
| 16 |
tape drives (i.e. \acs{OS} drivers) seem to work on Windows systems. However, |
| 17 |
non-SCSI tape drives (other than the OnStream) that use \texttt{ide-scsi}, \texttt{ide-tape}, |
| 18 |
or other non-scsi drivers do not function correctly with \bacula{} (or any |
| 19 |
other demanding tape application) as of today (April 2007). If you |
| 20 |
have purchased a non-SCSI tape drive for use with \bacula{} on Linux, there |
| 21 |
is a good chance that it will not work. We are working with the kernel |
| 22 |
developers to rectify this situation, but it will not be resolved in the |
| 23 |
near future. |
| 24 |
|
| 25 |
Generally any modern tape drive (i.e. after 2010) will work out |
| 26 |
of the box with \bacula{} using the standard \bacula{} Device specification |
| 27 |
in the \bfilename{bacula-sd.conf} file. |
| 28 |
|
| 29 |
Even if your drive is on the list below, please check the |
| 30 |
\bxlink{Tape Testing}{blb:btape1}{problems}{section} of the \bproblemman{} for |
| 31 |
procedures that you can use to verify if your tape drive will work with |
| 32 |
\bacula{}. If your drive is in fixed block mode, it may appear to work with |
| 33 |
\bacula{} until you attempt to do a restore and \bacula{} wants to position the |
| 34 |
tape. You can be sure only by following the procedures suggested above and |
| 35 |
testing. |
| 36 |
|
| 37 |
It is very difficult to supply a list of supported tape drives, or drives that |
| 38 |
are known to work with \bacula{} because of limited feedback (so if you use |
| 39 |
\bacula{} on a different drive, please let us know). Based on user feedback, the |
| 40 |
following drives are known to work with \bacula{}. A dash in a column means |
| 41 |
unknown: |
| 42 |
|
| 43 |
\LTXtable{\linewidth}{t-main-tapedrives} |
| 44 |
|
| 45 |
There is a list of \bilink{supported autochangers}{blb:Models} in the Supported |
| 46 |
Autochangers chapter of this document, where you will find other tape drives |
| 47 |
that work with \bacula{}. |
| 48 |
|
| 49 |
\section{Unsupported Tape Drives} |
| 50 |
\label{blb:UnSupportedDrives} |
| 51 |
\index[general]{Unsupported Tape Drives } |
| 52 |
\index[general]{Drives!Unsupported Tape } |
| 53 |
|
| 54 |
Previously OnStream IDE-SCSI tape drives did not work with \bacula{}. As of |
| 55 |
\bacula{} version 1.33 and the osst kernel driver version 0.9.14 or later, they |
| 56 |
now work. Please see the testing chapter as you must set a fixed block size. |
| 57 |
|
| 58 |
QIC tapes are known to have a number of particularities (fixed block size, and |
| 59 |
one EOF rather than two to terminate the tape). As a consequence, you will |
| 60 |
need to take a lot of care in configuring them to make them work correctly |
| 61 |
with \bacula{}. |
| 62 |
|
| 63 |
\section{FreeBSD Users Be Aware!!!} |
| 64 |
\index[general]{FreeBSD Users Be Aware } |
| 65 |
\index[general]{Aware!FreeBSD Users Be } |
| 66 |
|
| 67 |
Unless you have patched the pthreads library on FreeBSD 4.11 systems, you will |
| 68 |
lose data when \bacula{} spans tapes. This is because the unpatched pthreads |
| 69 |
library fails to return a warning status to \bacula{} that the end of the tape is |
| 70 |
near. This problem is fixed in FreeBSD systems released after 4.11. Please see the |
| 71 |
\bxlink{Tape testing}{blb:FreeBSDTapes}{problems}{section} of \bproblemman{} |
| 72 |
for \textbf{important} information on how to configure your tape drive for |
| 73 |
compatibility with \bacula{}. |
| 74 |
|
| 75 |
\section{Supported Autochangers} |
| 76 |
\index[general]{Autochangers!Supported } |
| 77 |
\index[general]{Supported Autochangers } |
| 78 |
|
| 79 |
For information on supported autochangers, please see the |
| 80 |
\bilink{Autochangers Known to Work with \bacula{}}{blb:Models} |
| 81 |
section of the Supported Autochangers chapter of this manual. |
| 82 |
|
| 83 |
\section{Tape Specifications} |
| 84 |
\index[general]{Specifications!Tape} |
| 85 |
\index[general]{Tape Specifications} |
| 86 |
If you want to know what tape drive to buy that will work with \bacula{}, |
| 87 |
we really cannot tell you. However, we can say that if you are going |
| 88 |
to buy a drive, you should try to avoid DDS drives. The technology is |
| 89 |
rather old and DDS tape drives need frequent cleaning. DLT drives are |
| 90 |
generally much better (newer technology) and do not need frequent |
| 91 |
cleaning. |
| 92 |
|
| 93 |
Below, you will find a table of \acs{DLT} and \acs{LTO} tape specifications that will |
| 94 |
give you some idea of the capacity and speed of modern tapes. The |
| 95 |
capacities that are listed are the native tape capacity without compression. |
| 96 |
All modern drives have hardware compression, and manufacturers often list |
| 97 |
compressed capacity using a compression ration of 2:1. The actual compression |
| 98 |
ratio will depend mostly on the data you have to backup, but I find that |
| 99 |
1.5:1 is a much more reasonable number (i.e. multiply the value shown in |
| 100 |
the table by 1.5 to get a rough average of what you will probably see). |
| 101 |
The transfer rates are rounded to the nearest GB/h. All values are provided |
| 102 |
by various manufacturers. |
| 103 |
|
| 104 |
The Media Type is what is designated by the manufacturers and you are not |
| 105 |
required to use (but you may) the same name in your \bacula{} conf resources. |
| 106 |
|
| 107 |
|
| 108 |
\LTXtable{\linewidth}{t-main-lto-dlt-spec} |