| 1 |
/**********************************************************/ |
| 2 |
/* Optiboot bootloader for Arduino */ |
| 3 |
/* */ |
| 4 |
/* http://optiboot.googlecode.com */ |
| 5 |
/* */ |
| 6 |
/* Arduino-maintained version : See README.TXT */ |
| 7 |
/* http://code.google.com/p/arduino/ */ |
| 8 |
/* */ |
| 9 |
/* Heavily optimised bootloader that is faster and */ |
| 10 |
/* smaller than the Arduino standard bootloader */ |
| 11 |
/* */ |
| 12 |
/* Enhancements: */ |
| 13 |
/* Fits in 512 bytes, saving 1.5K of code space */ |
| 14 |
/* Background page erasing speeds up programming */ |
| 15 |
/* Higher baud rate speeds up programming */ |
| 16 |
/* Written almost entirely in C */ |
| 17 |
/* Customisable timeout with accurate timeconstant */ |
| 18 |
/* Optional virtual UART. No hardware UART required. */ |
| 19 |
/* Optional virtual boot partition for devices without. */ |
| 20 |
/* */ |
| 21 |
/* What you lose: */ |
| 22 |
/* Implements a skeleton STK500 protocol which is */ |
| 23 |
/* missing several features including EEPROM */ |
| 24 |
/* programming and non-page-aligned writes */ |
| 25 |
/* High baud rate breaks compatibility with standard */ |
| 26 |
/* Arduino flash settings */ |
| 27 |
/* */ |
| 28 |
/* Fully supported: */ |
| 29 |
/* ATmega168 based devices (Diecimila etc) */ |
| 30 |
/* ATmega328P based devices (Duemilanove etc) */ |
| 31 |
/* */ |
| 32 |
/* Alpha test */ |
| 33 |
/* ATmega1280 based devices (Arduino Mega) */ |
| 34 |
/* */ |
| 35 |
/* Work in progress: */ |
| 36 |
/* ATmega644P based devices (Sanguino) */ |
| 37 |
/* ATtiny84 based devices (Luminet) */ |
| 38 |
/* */ |
| 39 |
/* Does not support: */ |
| 40 |
/* USB based devices (eg. Teensy) */ |
| 41 |
/* */ |
| 42 |
/* Assumptions: */ |
| 43 |
/* The code makes several assumptions that reduce the */ |
| 44 |
/* code size. They are all true after a hardware reset, */ |
| 45 |
/* but may not be true if the bootloader is called by */ |
| 46 |
/* other means or on other hardware. */ |
| 47 |
/* No interrupts can occur */ |
| 48 |
/* UART and Timer 1 are set to their reset state */ |
| 49 |
/* SP points to RAMEND */ |
| 50 |
/* */ |
| 51 |
/* Code builds on code, libraries and optimisations from: */ |
| 52 |
/* stk500boot.c by Jason P. Kyle */ |
| 53 |
/* Arduino bootloader http://www.arduino.cc */ |
| 54 |
/* Spiff's 1K bootloader http://spiffie.org/know/arduino_1k_bootloader/bootloader.shtml */ |
| 55 |
/* avr-libc project http://nongnu.org/avr-libc */ |
| 56 |
/* Adaboot http://www.ladyada.net/library/arduino/bootloader.html */ |
| 57 |
/* AVR305 Atmel Application Note */ |
| 58 |
/* */ |
| 59 |
/* This program is free software; you can redistribute it */ |
| 60 |
/* and/or modify it under the terms of the GNU General */ |
| 61 |
/* Public License as published by the Free Software */ |
| 62 |
/* Foundation; either version 2 of the License, or */ |
| 63 |
/* (at your option) any later version. */ |
| 64 |
/* */ |
| 65 |
/* This program is distributed in the hope that it will */ |
| 66 |
/* be useful, but WITHOUT ANY WARRANTY; without even the */ |
| 67 |
/* implied warranty of MERCHANTABILITY or FITNESS FOR A */ |
| 68 |
/* PARTICULAR PURPOSE. See the GNU General Public */ |
| 69 |
/* License for more details. */ |
| 70 |
/* */ |
| 71 |
/* You should have received a copy of the GNU General */ |
| 72 |
/* Public License along with this program; if not, write */ |
| 73 |
/* to the Free Software Foundation, Inc., */ |
| 74 |
/* 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ |
| 75 |
/* */ |
| 76 |
/* Licence can be viewed at */ |
| 77 |
/* http://www.fsf.org/licenses/gpl.txt */ |
| 78 |
/* */ |
| 79 |
/**********************************************************/ |
| 80 |
|
| 81 |
|
| 82 |
/**********************************************************/ |
| 83 |
/* */ |
| 84 |
/* Optional defines: */ |
| 85 |
/* */ |
| 86 |
/**********************************************************/ |
| 87 |
/* */ |
| 88 |
/* BIG_BOOT: */ |
| 89 |
/* Build a 1k bootloader, not 512 bytes. This turns on */ |
| 90 |
/* extra functionality. */ |
| 91 |
/* */ |
| 92 |
/* BAUD_RATE: */ |
| 93 |
/* Set bootloader baud rate. */ |
| 94 |
/* */ |
| 95 |
/* LUDICROUS_SPEED: */ |
| 96 |
/* 230400 baud :-) */ |
| 97 |
/* */ |
| 98 |
/* SOFT_UART: */ |
| 99 |
/* Use AVR305 soft-UART instead of hardware UART. */ |
| 100 |
/* */ |
| 101 |
/* LED_START_FLASHES: */ |
| 102 |
/* Number of LED flashes on bootup. */ |
| 103 |
/* */ |
| 104 |
/* LED_DATA_FLASH: */ |
| 105 |
/* Flash LED when transferring data. For boards without */ |
| 106 |
/* TX or RX LEDs, or for people who like blinky lights. */ |
| 107 |
/* */ |
| 108 |
/* SUPPORT_EEPROM: */ |
| 109 |
/* Support reading and writing from EEPROM. This is not */ |
| 110 |
/* used by Arduino, so off by default. */ |
| 111 |
/* */ |
| 112 |
/* TIMEOUT_MS: */ |
| 113 |
/* Bootloader timeout period, in milliseconds. */ |
| 114 |
/* 500,1000,2000,4000,8000 supported. */ |
| 115 |
/* */ |
| 116 |
/**********************************************************/ |
| 117 |
|
| 118 |
/**********************************************************/ |
| 119 |
/* Version Numbers! */ |
| 120 |
/* */ |
| 121 |
/* Arduino Optiboot now includes this Version number in */ |
| 122 |
/* the source and object code. */ |
| 123 |
/* */ |
| 124 |
/* Version 3 was released as zip from the optiboot */ |
| 125 |
/* repository and was distributed with Arduino 0022. */ |
| 126 |
/* Version 4 starts with the arduino repository commit */ |
| 127 |
/* that brought the arduino repository up-to-date with */ |
| 128 |
/* the optiboot source tree changes since v3. */ |
| 129 |
/* */ |
| 130 |
/**********************************************************/ |
| 131 |
|
| 132 |
/**********************************************************/ |
| 133 |
/* Edit History: */ |
| 134 |
/* */ |
| 135 |
/* 4.4 WestfW: add initialization of address to keep */ |
| 136 |
/* the compiler happy. Change SC'ed targets. */ |
| 137 |
/* Return the SW version via READ PARAM */ |
| 138 |
/* 4.3 WestfW: catch framing errors in getch(), so that */ |
| 139 |
/* AVRISP works without HW kludges. */ |
| 140 |
/* http://code.google.com/p/arduino/issues/detail?id=368n*/ |
| 141 |
/* 4.2 WestfW: reduce code size, fix timeouts, change */ |
| 142 |
/* verifySpace to use WDT instead of appstart */ |
| 143 |
/* 4.1 WestfW: put version number in binary. */ |
| 144 |
/**********************************************************/ |
| 145 |
|
| 146 |
#define OPTIBOOT_MAJVER 4 |
| 147 |
#define OPTIBOOT_MINVER 4 |
| 148 |
|
| 149 |
#define MAKESTR(a) #a |
| 150 |
#define MAKEVER(a, b) MAKESTR(a*256+b) |
| 151 |
|
| 152 |
asm(" .section .version\n" |
| 153 |
"optiboot_version: .word " MAKEVER(OPTIBOOT_MAJVER, OPTIBOOT_MINVER) "\n" |
| 154 |
" .section .text\n"); |
| 155 |
|
| 156 |
#include <inttypes.h> |
| 157 |
#include <avr/io.h> |
| 158 |
#include <avr/pgmspace.h> |
| 159 |
|
| 160 |
// <avr/boot.h> uses sts instructions, but this version uses out instructions |
| 161 |
// This saves cycles and program memory. |
| 162 |
#include "boot.h" |
| 163 |
|
| 164 |
|
| 165 |
// We don't use <avr/wdt.h> as those routines have interrupt overhead we don't need. |
| 166 |
|
| 167 |
#include "pin_defs.h" |
| 168 |
#include "stk500.h" |
| 169 |
|
| 170 |
#ifndef LED_START_FLASHES |
| 171 |
#define LED_START_FLASHES 0 |
| 172 |
#endif |
| 173 |
|
| 174 |
#ifdef LUDICROUS_SPEED |
| 175 |
#define BAUD_RATE 230400L |
| 176 |
#endif |
| 177 |
|
| 178 |
/* set the UART baud rate defaults */ |
| 179 |
#ifndef BAUD_RATE |
| 180 |
#if F_CPU >= 8000000L |
| 181 |
#define BAUD_RATE 115200L // Highest rate Avrdude win32 will support |
| 182 |
#elsif F_CPU >= 1000000L |
| 183 |
#define BAUD_RATE 9600L // 19200 also supported, but with significant error |
| 184 |
#elsif F_CPU >= 128000L |
| 185 |
#define BAUD_RATE 4800L // Good for 128kHz internal RC |
| 186 |
#else |
| 187 |
#define BAUD_RATE 1200L // Good even at 32768Hz |
| 188 |
#endif |
| 189 |
#endif |
| 190 |
|
| 191 |
/* Switch in soft UART for hard baud rates */ |
| 192 |
#if (F_CPU/BAUD_RATE) > 280 // > 57600 for 16MHz |
| 193 |
#ifndef SOFT_UART |
| 194 |
#define SOFT_UART |
| 195 |
#endif |
| 196 |
#endif |
| 197 |
|
| 198 |
/* Watchdog settings */ |
| 199 |
#define WATCHDOG_OFF (0) |
| 200 |
#define WATCHDOG_16MS (_BV(WDE)) |
| 201 |
#define WATCHDOG_32MS (_BV(WDP0) | _BV(WDE)) |
| 202 |
#define WATCHDOG_64MS (_BV(WDP1) | _BV(WDE)) |
| 203 |
#define WATCHDOG_125MS (_BV(WDP1) | _BV(WDP0) | _BV(WDE)) |
| 204 |
#define WATCHDOG_250MS (_BV(WDP2) | _BV(WDE)) |
| 205 |
#define WATCHDOG_500MS (_BV(WDP2) | _BV(WDP0) | _BV(WDE)) |
| 206 |
#define WATCHDOG_1S (_BV(WDP2) | _BV(WDP1) | _BV(WDE)) |
| 207 |
#define WATCHDOG_2S (_BV(WDP2) | _BV(WDP1) | _BV(WDP0) | _BV(WDE)) |
| 208 |
#ifndef __AVR_ATmega8__ |
| 209 |
#define WATCHDOG_4S (_BV(WDP3) | _BV(WDE)) |
| 210 |
#define WATCHDOG_8S (_BV(WDP3) | _BV(WDP0) | _BV(WDE)) |
| 211 |
#endif |
| 212 |
|
| 213 |
/* Function Prototypes */ |
| 214 |
/* The main function is in init9, which removes the interrupt vector table */ |
| 215 |
/* we don't need. It is also 'naked', which means the compiler does not */ |
| 216 |
/* generate any entry or exit code itself. */ |
| 217 |
int main(void) __attribute__ ((naked)) __attribute__ ((section (".init9"))); |
| 218 |
void putch(char); |
| 219 |
uint8_t getch(void); |
| 220 |
static inline void getNch(uint8_t); /* "static inline" is a compiler hint to reduce code size */ |
| 221 |
void verifySpace(); |
| 222 |
static inline void flash_led(uint8_t); |
| 223 |
uint8_t getLen(); |
| 224 |
static inline void watchdogReset(); |
| 225 |
void watchdogConfig(uint8_t x); |
| 226 |
#ifdef SOFT_UART |
| 227 |
void uartDelay() __attribute__ ((naked)); |
| 228 |
#endif |
| 229 |
void appStart() __attribute__ ((naked)); |
| 230 |
|
| 231 |
#if defined(__AVR_ATmega168__) |
| 232 |
#define RAMSTART (0x100) |
| 233 |
#define NRWWSTART (0x3800) |
| 234 |
#elif defined(__AVR_ATmega328P__) || defined(__AVR_ATmega328__) |
| 235 |
#define RAMSTART (0x100) |
| 236 |
#define NRWWSTART (0x7000) |
| 237 |
#elif defined (__AVR_ATmega644P__) |
| 238 |
#define RAMSTART (0x100) |
| 239 |
#define NRWWSTART (0xE000) |
| 240 |
#elif defined(__AVR_ATtiny84__) |
| 241 |
#define RAMSTART (0x100) |
| 242 |
#define NRWWSTART (0x0000) |
| 243 |
#elif defined(__AVR_ATmega1280__) |
| 244 |
#define RAMSTART (0x200) |
| 245 |
#define NRWWSTART (0xE000) |
| 246 |
#elif defined(__AVR_ATmega8__) || defined(__AVR_ATmega88__) |
| 247 |
#define RAMSTART (0x100) |
| 248 |
#define NRWWSTART (0x1800) |
| 249 |
#endif |
| 250 |
|
| 251 |
/* C zero initialises all global variables. However, that requires */ |
| 252 |
/* These definitions are NOT zero initialised, but that doesn't matter */ |
| 253 |
/* This allows us to drop the zero init code, saving us memory */ |
| 254 |
#define buff ((uint8_t*)(RAMSTART)) |
| 255 |
#ifdef VIRTUAL_BOOT_PARTITION |
| 256 |
#define rstVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+4)) |
| 257 |
#define wdtVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+6)) |
| 258 |
#endif |
| 259 |
|
| 260 |
/* main program starts here */ |
| 261 |
int main(void) { |
| 262 |
uint8_t ch; |
| 263 |
|
| 264 |
/* |
| 265 |
* Making these local and in registers prevents the need for initializing |
| 266 |
* them, and also saves space because code no longer stores to memory. |
| 267 |
* (initializing address keeps the compiler happy, but isn't really |
| 268 |
* necessary, and uses 4 bytes of flash.) |
| 269 |
*/ |
| 270 |
register uint16_t address = 0; |
| 271 |
register uint8_t length; |
| 272 |
|
| 273 |
// After the zero init loop, this is the first code to run. |
| 274 |
// |
| 275 |
// This code makes the following assumptions: |
| 276 |
// No interrupts will execute |
| 277 |
// SP points to RAMEND |
| 278 |
// r1 contains zero |
| 279 |
// |
| 280 |
// If not, uncomment the following instructions: |
| 281 |
// cli(); |
| 282 |
asm volatile ("clr __zero_reg__"); |
| 283 |
#ifdef __AVR_ATmega8__ |
| 284 |
SP=RAMEND; // This is done by hardware reset |
| 285 |
#endif |
| 286 |
|
| 287 |
// Adaboot no-wait mod |
| 288 |
ch = MCUSR; |
| 289 |
MCUSR = 0; |
| 290 |
if (!(ch & _BV(EXTRF))) appStart(); |
| 291 |
|
| 292 |
#if LED_START_FLASHES > 0 |
| 293 |
// Set up Timer 1 for timeout counter |
| 294 |
TCCR1B = _BV(CS12) | _BV(CS10); // div 1024 |
| 295 |
#endif |
| 296 |
#ifndef SOFT_UART |
| 297 |
#ifdef __AVR_ATmega8__ |
| 298 |
UCSRA = _BV(U2X); //Double speed mode USART |
| 299 |
UCSRB = _BV(RXEN) | _BV(TXEN); // enable Rx & Tx |
| 300 |
UCSRC = _BV(URSEL) | _BV(UCSZ1) | _BV(UCSZ0); // config USART; 8N1 |
| 301 |
UBRRL = (uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 ); |
| 302 |
#else |
| 303 |
UCSR0A = _BV(U2X0); //Double speed mode USART0 |
| 304 |
UCSR0B = _BV(RXEN0) | _BV(TXEN0); |
| 305 |
UCSR0C = _BV(UCSZ00) | _BV(UCSZ01); |
| 306 |
UBRR0L = (uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 ); |
| 307 |
#endif |
| 308 |
#endif |
| 309 |
|
| 310 |
// Set up watchdog to trigger after 500ms |
| 311 |
watchdogConfig(WATCHDOG_1S); |
| 312 |
|
| 313 |
/* Set LED pin as output */ |
| 314 |
LED_DDR |= _BV(LED); |
| 315 |
|
| 316 |
#ifdef SOFT_UART |
| 317 |
/* Set TX pin as output */ |
| 318 |
UART_DDR |= _BV(UART_TX_BIT); |
| 319 |
#endif |
| 320 |
|
| 321 |
#if LED_START_FLASHES > 0 |
| 322 |
/* Flash onboard LED to signal entering of bootloader */ |
| 323 |
flash_led(LED_START_FLASHES * 2); |
| 324 |
#endif |
| 325 |
|
| 326 |
/* Forever loop */ |
| 327 |
for (;;) { |
| 328 |
/* get character from UART */ |
| 329 |
ch = getch(); |
| 330 |
|
| 331 |
if(ch == STK_GET_PARAMETER) { |
| 332 |
unsigned char which = getch(); |
| 333 |
verifySpace(); |
| 334 |
if (which == 0x82) { |
| 335 |
/* |
| 336 |
* Send optiboot version as "minor SW version" |
| 337 |
*/ |
| 338 |
putch(OPTIBOOT_MINVER); |
| 339 |
} else if (which == 0x81) { |
| 340 |
putch(OPTIBOOT_MAJVER); |
| 341 |
} else { |
| 342 |
/* |
| 343 |
* GET PARAMETER returns a generic 0x03 reply for |
| 344 |
* other parameters - enough to keep Avrdude happy |
| 345 |
*/ |
| 346 |
putch(0x03); |
| 347 |
} |
| 348 |
} |
| 349 |
else if(ch == STK_SET_DEVICE) { |
| 350 |
// SET DEVICE is ignored |
| 351 |
getNch(20); |
| 352 |
} |
| 353 |
else if(ch == STK_SET_DEVICE_EXT) { |
| 354 |
// SET DEVICE EXT is ignored |
| 355 |
getNch(5); |
| 356 |
} |
| 357 |
else if(ch == STK_LOAD_ADDRESS) { |
| 358 |
// LOAD ADDRESS |
| 359 |
uint16_t newAddress; |
| 360 |
newAddress = getch(); |
| 361 |
newAddress = (newAddress & 0xff) | (getch() << 8); |
| 362 |
#ifdef RAMPZ |
| 363 |
// Transfer top bit to RAMPZ |
| 364 |
RAMPZ = (newAddress & 0x8000) ? 1 : 0; |
| 365 |
#endif |
| 366 |
newAddress += newAddress; // Convert from word address to byte address |
| 367 |
address = newAddress; |
| 368 |
verifySpace(); |
| 369 |
} |
| 370 |
else if(ch == STK_UNIVERSAL) { |
| 371 |
// UNIVERSAL command is ignored |
| 372 |
getNch(4); |
| 373 |
putch(0x00); |
| 374 |
} |
| 375 |
/* Write memory, length is big endian and is in bytes */ |
| 376 |
else if(ch == STK_PROG_PAGE) { |
| 377 |
// PROGRAM PAGE - we support flash programming only, not EEPROM |
| 378 |
uint8_t *bufPtr; |
| 379 |
uint16_t addrPtr; |
| 380 |
|
| 381 |
getch(); /* getlen() */ |
| 382 |
length = getch(); |
| 383 |
getch(); |
| 384 |
|
| 385 |
// If we are in RWW section, immediately start page erase |
| 386 |
if (address < NRWWSTART) __boot_page_erase_short((uint16_t)(void*)address); |
| 387 |
|
| 388 |
// While that is going on, read in page contents |
| 389 |
bufPtr = buff; |
| 390 |
do *bufPtr++ = getch(); |
| 391 |
while (--length); |
| 392 |
|
| 393 |
// If we are in NRWW section, page erase has to be delayed until now. |
| 394 |
// Todo: Take RAMPZ into account |
| 395 |
if (address >= NRWWSTART) __boot_page_erase_short((uint16_t)(void*)address); |
| 396 |
|
| 397 |
// Read command terminator, start reply |
| 398 |
verifySpace(); |
| 399 |
|
| 400 |
// If only a partial page is to be programmed, the erase might not be complete. |
| 401 |
// So check that here |
| 402 |
boot_spm_busy_wait(); |
| 403 |
|
| 404 |
#ifdef VIRTUAL_BOOT_PARTITION |
| 405 |
if ((uint16_t)(void*)address == 0) { |
| 406 |
// This is the reset vector page. We need to live-patch the code so the |
| 407 |
// bootloader runs. |
| 408 |
// |
| 409 |
// Move RESET vector to WDT vector |
| 410 |
uint16_t vect = buff[0] | (buff[1]<<8); |
| 411 |
rstVect = vect; |
| 412 |
wdtVect = buff[8] | (buff[9]<<8); |
| 413 |
vect -= 4; // Instruction is a relative jump (rjmp), so recalculate. |
| 414 |
buff[8] = vect & 0xff; |
| 415 |
buff[9] = vect >> 8; |
| 416 |
|
| 417 |
// Add jump to bootloader at RESET vector |
| 418 |
buff[0] = 0x7f; |
| 419 |
buff[1] = 0xce; // rjmp 0x1d00 instruction |
| 420 |
} |
| 421 |
#endif |
| 422 |
|
| 423 |
// Copy buffer into programming buffer |
| 424 |
bufPtr = buff; |
| 425 |
addrPtr = (uint16_t)(void*)address; |
| 426 |
ch = SPM_PAGESIZE / 2; |
| 427 |
do { |
| 428 |
uint16_t a; |
| 429 |
a = *bufPtr++; |
| 430 |
a |= (*bufPtr++) << 8; |
| 431 |
__boot_page_fill_short((uint16_t)(void*)addrPtr,a); |
| 432 |
addrPtr += 2; |
| 433 |
} while (--ch); |
| 434 |
|
| 435 |
// Write from programming buffer |
| 436 |
__boot_page_write_short((uint16_t)(void*)address); |
| 437 |
boot_spm_busy_wait(); |
| 438 |
|
| 439 |
#if defined(RWWSRE) |
| 440 |
// Reenable read access to flash |
| 441 |
boot_rww_enable(); |
| 442 |
#endif |
| 443 |
|
| 444 |
} |
| 445 |
/* Read memory block mode, length is big endian. */ |
| 446 |
else if(ch == STK_READ_PAGE) { |
| 447 |
// READ PAGE - we only read flash |
| 448 |
getch(); /* getlen() */ |
| 449 |
length = getch(); |
| 450 |
getch(); |
| 451 |
|
| 452 |
verifySpace(); |
| 453 |
#ifdef VIRTUAL_BOOT_PARTITION |
| 454 |
do { |
| 455 |
// Undo vector patch in bottom page so verify passes |
| 456 |
if (address == 0) ch=rstVect & 0xff; |
| 457 |
else if (address == 1) ch=rstVect >> 8; |
| 458 |
else if (address == 8) ch=wdtVect & 0xff; |
| 459 |
else if (address == 9) ch=wdtVect >> 8; |
| 460 |
else ch = pgm_read_byte_near(address); |
| 461 |
address++; |
| 462 |
putch(ch); |
| 463 |
} while (--length); |
| 464 |
#else |
| 465 |
#ifdef __AVR_ATmega1280__ |
| 466 |
// do putch(pgm_read_byte_near(address++)); |
| 467 |
// while (--length); |
| 468 |
do { |
| 469 |
uint8_t result; |
| 470 |
__asm__ ("elpm %0,Z\n":"=r"(result):"z"(address)); |
| 471 |
putch(result); |
| 472 |
address++; |
| 473 |
} |
| 474 |
while (--length); |
| 475 |
#else |
| 476 |
do putch(pgm_read_byte_near(address++)); |
| 477 |
while (--length); |
| 478 |
#endif |
| 479 |
#endif |
| 480 |
} |
| 481 |
|
| 482 |
/* Get device signature bytes */ |
| 483 |
else if(ch == STK_READ_SIGN) { |
| 484 |
// READ SIGN - return what Avrdude wants to hear |
| 485 |
verifySpace(); |
| 486 |
putch(SIGNATURE_0); |
| 487 |
putch(SIGNATURE_1); |
| 488 |
putch(SIGNATURE_2); |
| 489 |
} |
| 490 |
else if (ch == 'Q') { |
| 491 |
// Adaboot no-wait mod |
| 492 |
watchdogConfig(WATCHDOG_16MS); |
| 493 |
verifySpace(); |
| 494 |
} |
| 495 |
else { |
| 496 |
// This covers the response to commands like STK_ENTER_PROGMODE |
| 497 |
verifySpace(); |
| 498 |
} |
| 499 |
putch(STK_OK); |
| 500 |
} |
| 501 |
} |
| 502 |
|
| 503 |
void putch(char ch) { |
| 504 |
#ifndef SOFT_UART |
| 505 |
while (!(UCSR0A & _BV(UDRE0))); |
| 506 |
UDR0 = ch; |
| 507 |
#else |
| 508 |
__asm__ __volatile__ ( |
| 509 |
" com %[ch]\n" // ones complement, carry set |
| 510 |
" sec\n" |
| 511 |
"1: brcc 2f\n" |
| 512 |
" cbi %[uartPort],%[uartBit]\n" |
| 513 |
" rjmp 3f\n" |
| 514 |
"2: sbi %[uartPort],%[uartBit]\n" |
| 515 |
" nop\n" |
| 516 |
"3: rcall uartDelay\n" |
| 517 |
" rcall uartDelay\n" |
| 518 |
" lsr %[ch]\n" |
| 519 |
" dec %[bitcnt]\n" |
| 520 |
" brne 1b\n" |
| 521 |
: |
| 522 |
: |
| 523 |
[bitcnt] "d" (10), |
| 524 |
[ch] "r" (ch), |
| 525 |
[uartPort] "I" (_SFR_IO_ADDR(UART_PORT)), |
| 526 |
[uartBit] "I" (UART_TX_BIT) |
| 527 |
: |
| 528 |
"r25" |
| 529 |
); |
| 530 |
#endif |
| 531 |
} |
| 532 |
|
| 533 |
uint8_t getch(void) { |
| 534 |
uint8_t ch; |
| 535 |
|
| 536 |
#ifdef LED_DATA_FLASH |
| 537 |
#ifdef __AVR_ATmega8__ |
| 538 |
LED_PORT ^= _BV(LED); |
| 539 |
#else |
| 540 |
LED_PIN |= _BV(LED); |
| 541 |
#endif |
| 542 |
#endif |
| 543 |
|
| 544 |
#ifdef SOFT_UART |
| 545 |
__asm__ __volatile__ ( |
| 546 |
"1: sbic %[uartPin],%[uartBit]\n" // Wait for start edge |
| 547 |
" rjmp 1b\n" |
| 548 |
" rcall uartDelay\n" // Get to middle of start bit |
| 549 |
"2: rcall uartDelay\n" // Wait 1 bit period |
| 550 |
" rcall uartDelay\n" // Wait 1 bit period |
| 551 |
" clc\n" |
| 552 |
" sbic %[uartPin],%[uartBit]\n" |
| 553 |
" sec\n" |
| 554 |
" dec %[bitCnt]\n" |
| 555 |
" breq 3f\n" |
| 556 |
" ror %[ch]\n" |
| 557 |
" rjmp 2b\n" |
| 558 |
"3:\n" |
| 559 |
: |
| 560 |
[ch] "=r" (ch) |
| 561 |
: |
| 562 |
[bitCnt] "d" (9), |
| 563 |
[uartPin] "I" (_SFR_IO_ADDR(UART_PIN)), |
| 564 |
[uartBit] "I" (UART_RX_BIT) |
| 565 |
: |
| 566 |
"r25" |
| 567 |
); |
| 568 |
#else |
| 569 |
while(!(UCSR0A & _BV(RXC0))) |
| 570 |
; |
| 571 |
if (!(UCSR0A & _BV(FE0))) { |
| 572 |
/* |
| 573 |
* A Framing Error indicates (probably) that something is talking |
| 574 |
* to us at the wrong bit rate. Assume that this is because it |
| 575 |
* expects to be talking to the application, and DON'T reset the |
| 576 |
* watchdog. This should cause the bootloader to abort and run |
| 577 |
* the application "soon", if it keeps happening. (Note that we |
| 578 |
* don't care that an invalid char is returned...) |
| 579 |
*/ |
| 580 |
watchdogReset(); |
| 581 |
} |
| 582 |
|
| 583 |
ch = UDR0; |
| 584 |
#endif |
| 585 |
|
| 586 |
#ifdef LED_DATA_FLASH |
| 587 |
#ifdef __AVR_ATmega8__ |
| 588 |
LED_PORT ^= _BV(LED); |
| 589 |
#else |
| 590 |
LED_PIN |= _BV(LED); |
| 591 |
#endif |
| 592 |
#endif |
| 593 |
|
| 594 |
return ch; |
| 595 |
} |
| 596 |
|
| 597 |
#ifdef SOFT_UART |
| 598 |
// AVR350 equation: #define UART_B_VALUE (((F_CPU/BAUD_RATE)-23)/6) |
| 599 |
// Adding 3 to numerator simulates nearest rounding for more accurate baud rates |
| 600 |
#define UART_B_VALUE (((F_CPU/BAUD_RATE)-20)/6) |
| 601 |
#if UART_B_VALUE > 255 |
| 602 |
#error Baud rate too slow for soft UART |
| 603 |
#endif |
| 604 |
|
| 605 |
void uartDelay() { |
| 606 |
__asm__ __volatile__ ( |
| 607 |
"ldi r25,%[count]\n" |
| 608 |
"1:dec r25\n" |
| 609 |
"brne 1b\n" |
| 610 |
"ret\n" |
| 611 |
::[count] "M" (UART_B_VALUE) |
| 612 |
); |
| 613 |
} |
| 614 |
#endif |
| 615 |
|
| 616 |
void getNch(uint8_t count) { |
| 617 |
do getch(); while (--count); |
| 618 |
verifySpace(); |
| 619 |
} |
| 620 |
|
| 621 |
void verifySpace() { |
| 622 |
if (getch() != CRC_EOP) { |
| 623 |
watchdogConfig(WATCHDOG_16MS); // shorten WD timeout |
| 624 |
while (1) // and busy-loop so that WD causes |
| 625 |
; // a reset and app start. |
| 626 |
} |
| 627 |
putch(STK_INSYNC); |
| 628 |
} |
| 629 |
|
| 630 |
#if LED_START_FLASHES > 0 |
| 631 |
void flash_led(uint8_t count) { |
| 632 |
do { |
| 633 |
TCNT1 = -(F_CPU/(1024*16)); |
| 634 |
TIFR1 = _BV(TOV1); |
| 635 |
while(!(TIFR1 & _BV(TOV1))); |
| 636 |
#ifdef __AVR_ATmega8__ |
| 637 |
LED_PORT ^= _BV(LED); |
| 638 |
#else |
| 639 |
LED_PIN |= _BV(LED); |
| 640 |
#endif |
| 641 |
watchdogReset(); |
| 642 |
} while (--count); |
| 643 |
} |
| 644 |
#endif |
| 645 |
|
| 646 |
// Watchdog functions. These are only safe with interrupts turned off. |
| 647 |
void watchdogReset() { |
| 648 |
__asm__ __volatile__ ( |
| 649 |
"wdr\n" |
| 650 |
); |
| 651 |
} |
| 652 |
|
| 653 |
void watchdogConfig(uint8_t x) { |
| 654 |
WDTCSR = _BV(WDCE) | _BV(WDE); |
| 655 |
WDTCSR = x; |
| 656 |
} |
| 657 |
|
| 658 |
void appStart() { |
| 659 |
watchdogConfig(WATCHDOG_OFF); |
| 660 |
__asm__ __volatile__ ( |
| 661 |
#ifdef VIRTUAL_BOOT_PARTITION |
| 662 |
// Jump to WDT vector |
| 663 |
"ldi r30,4\n" |
| 664 |
"clr r31\n" |
| 665 |
#else |
| 666 |
// Jump to RST vector |
| 667 |
"clr r30\n" |
| 668 |
"clr r31\n" |
| 669 |
#endif |
| 670 |
"ijmp\n" |
| 671 |
); |
| 672 |
} |