Debian Codegraph @

src/SZ3/tools/sz3/sz3.config

raw
1 [GlobalSettings]
2
3 # The compression algorithms are:
4 # ALGO_INTERP_LORENZO
5 # The default algorithm in SZ3. It is the implementation of our ICDE'21 paper.
6 # The whole dataset will be compressed by interpolation or lorenzo predictor with auto-optimized settings.
7 # ALGO_INTERP
8 # The whole dataset will be compressed by interpolation predictor with default settings.
9 # ALGO_LORENZO_REG
10 # The whole dataset will be compressed by lorenzo and/or regression based predictors block by block with default settings.
11 # The four predictors ( 1st-order lorenzo, 2nd-order lorenzo, 1st-order regression, 2nd-order regression)
12 # can be enabled or disabled independently by conf settings (Lorenzo, Lorenzo2ndOrder, Regression, Regression2ndOrder).
13 CmprAlgo = ALGO_INTERP_LORENZO
14
15
16 #errorBoundMode: 6 options to control different types of error bounds
17 # "ABS", "REL", "PSNR", "NORM", "ABS_AND_REL", "ABS_OR_REL"
18 ErrorBoundMode = ABS
19
20 #absolute Error Bound (NOTE: it's valid when errorBoundMode is related to ABS (i.e., absolute error bound)
21 #absErrBound is to limit the (de)compression errors to be within an absolute error.
22 #For example, absErrBound=0.0001 means the decompressed value must be in [V-0.0001,V+0.0001], where V is the original true value.
23 AbsErrorBound = 1
24
25 #relative Bound Ratio (NOTE: it's valid only when errorBoundMode is related to REL (i.e., value_range based relative error bound)
26 #relErrBound is to limit the (de)compression errors by considering the global data value range size (i.e., taking into account the range size (max_value - min_value)).
27 #For example, suppose relBoundRatio is set to 0.01, and the data set is {100,101,102,103,104,...,110},
28 #so the global value range size is 110-100=10, so the error bound will actually be 10*0.01=0.1, from the perspective of "relBoundRatio"
29 RelErrorBound = 1e-3
30
31 #expected PSNR (Note: only valid when ErrorBoundMode = PSNR)
32 PSNRErrorBound = 70
33
34 #expected L2 NORM Error: sqrt((x1-x1')^2+(x2-x2')^2+....+(xN-xN')^2)
35 L2NormErrorBound = .333
36
37 #Use OpenMP for compression and decompression
38 OpenMP = NO
39
40 [AlgoSettings]
41 # settings for interpolation algorithm
42 # INTERP_ALGO_LINEAR
43 # use linear interpolation
44 # INTERP_ALGO_CUBIC
45 # use cubic spline interpolation
46 InterpolationAlgo = INTERP_ALGO_CUBIC
47 InterpolationDirection = 0
48
49 #settings for lorenzo and regression algorithms
50 Lorenzo = Yes
51 Lorenzo2ndOrder = No
52 Regression = Yes
53 Regression2ndOrder = No
54 #BlockSize = 6
55
56 #maximum quantization interval is valid only when quantization_intervals=0 (i.e., let the sz compressor optimize the intervals)
57 #In general, this setting does not change the compression ratio/rate, but only affect the compression speed to a certain extent (only 10% in general).
58 #The high values of max_quant_intervals, the lower compression speed,
59 #but the higher ability the compressor can reach high compression ratios for high-precision compression.
60 #As for low-precision compression (i.e., high error bound such as 1E-2), max_quant_intervals could be set to 256 or 65536.
61 #As for pretty-high-precision demand (i.e., fairly small error bound such as 1E-6), max_quant_intervals could be set to 2097152(=2^21).
62 QuantizationBinTotal = 65536