| 1 |
/* This file is part of the MicroPython project, http://micropython.org/ |
| 2 |
* MIT License; Copyright (c) 2019 Damien P. George |
| 3 |
*/ |
| 4 |
|
| 5 |
#define MICROPY_HW_BOARD_NAME "USBDongle-WB55" |
| 6 |
#define MICROPY_HW_MCU_NAME "STM32WB55CGU6" |
| 7 |
|
| 8 |
#define MICROPY_PY_PYB_LEGACY (0) |
| 9 |
|
| 10 |
#define MICROPY_HW_HAS_FLASH (1) |
| 11 |
#define MICROPY_HW_ENABLE_RTC (1) |
| 12 |
#define MICROPY_HW_ENABLE_RNG (1) |
| 13 |
#define MICROPY_HW_ENABLE_USB (1) |
| 14 |
#define MICROPY_HW_HAS_SWITCH (1) |
| 15 |
|
| 16 |
// There is an external 32kHz oscillator |
| 17 |
#define RTC_ASYNCH_PREDIV (0) |
| 18 |
#define RTC_SYNCH_PREDIV (0x7fff) |
| 19 |
#define MICROPY_HW_RTC_USE_LSE (1) |
| 20 |
#define MICROPY_HW_RTC_USE_US (1) |
| 21 |
|
| 22 |
// I2C buses |
| 23 |
#define MICROPY_HW_I2C1_SCL (pin_B8) |
| 24 |
#define MICROPY_HW_I2C1_SDA (pin_B9) |
| 25 |
|
| 26 |
// SPI buses |
| 27 |
#define MICROPY_HW_SPI1_SCK (pin_A5) // pin 8 on CN1 |
| 28 |
#define MICROPY_HW_SPI1_MISO (pin_A6) // pin 9 on CN1 |
| 29 |
#define MICROPY_HW_SPI1_MOSI (pin_A7) // pin 10 on CN1 |
| 30 |
|
| 31 |
// User switch; pressing the button makes the input go low |
| 32 |
#define MICROPY_HW_USRSW_PIN (pin_A10) |
| 33 |
#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP) |
| 34 |
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) |
| 35 |
#define MICROPY_HW_USRSW_PRESSED (0) |
| 36 |
|
| 37 |
// LEDs |
| 38 |
#define MICROPY_HW_LED1 (pin_B1) // red |
| 39 |
#define MICROPY_HW_LED2 (pin_B0) // green |
| 40 |
#define MICROPY_HW_LED3 (pin_A4) // blue |
| 41 |
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) |
| 42 |
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) |
| 43 |
|
| 44 |
// USB config |
| 45 |
#define MICROPY_HW_USB_FS (1) |
| 46 |
#define MICROPY_HW_USB_CDC_RX_DATA_SIZE (512) |
| 47 |
#define MICROPY_HW_USB_CDC_TX_DATA_SIZE (512) |
| 48 |
|
| 49 |
// Bluetooth config |
| 50 |
#define MICROPY_HW_BLE_UART_ID (0) |
| 51 |
#define MICROPY_HW_BLE_UART_BAUDRATE (115200) |