| 1 |
// The SparkFun MicroMod spec uses a zero-based peripheral numbering scheme. |
| 2 |
// In cases where the 0th peripheral is the default, the "0" is omitted from |
| 3 |
// the name (e.g. "I2C" instead of "I2C0"). |
| 4 |
// |
| 5 |
// Note: UART (UART0) is not present in the edge connector pinout because the |
| 6 |
// primary debug serial port is exposed as a virtual serial port over USB, |
| 7 |
// i.e. Serial.print() should print over USB VCP, not UART_TX1. |
| 8 |
// |
| 9 |
// For more details, see https://www.sparkfun.com/micromod#tech-specs |
| 10 |
|
| 11 |
#define MICROPY_HW_BOARD_NAME "SparkFun STM32 MicroMod Processor" |
| 12 |
#define MICROPY_HW_MCU_NAME "STM32F405RG" |
| 13 |
|
| 14 |
// 1 = use STM32 internal flash (1 MByte) |
| 15 |
// 0 = use onboard external SPI flash (16 MByte) |
| 16 |
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0) |
| 17 |
|
| 18 |
#define MICROPY_HW_HAS_FLASH (1) |
| 19 |
#define MICROPY_HW_ENABLE_RNG (1) |
| 20 |
#define MICROPY_HW_ENABLE_RTC (1) |
| 21 |
#define MICROPY_HW_ENABLE_DAC (1) |
| 22 |
#define MICROPY_HW_ENABLE_USB (1) |
| 23 |
|
| 24 |
// External SPI Flash config |
| 25 |
#if !MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE |
| 26 |
|
| 27 |
// 128 Mbit (16 MByte) external SPI flash |
| 28 |
#define MICROPY_HW_SPIFLASH_SIZE_BITS (128 * 1024 * 1024) |
| 29 |
|
| 30 |
#define MICROPY_HW_SPIFLASH_CS (pin_C3) |
| 31 |
#define MICROPY_HW_SPIFLASH_SCK (pin_C10) |
| 32 |
#define MICROPY_HW_SPIFLASH_MOSI (pin_C12) |
| 33 |
#define MICROPY_HW_SPIFLASH_MISO (pin_C11) |
| 34 |
|
| 35 |
#define MICROPY_BOARD_EARLY_INIT board_early_init |
| 36 |
void board_early_init(void); |
| 37 |
|
| 38 |
extern const struct _mp_spiflash_config_t spiflash_config; |
| 39 |
extern struct _spi_bdev_t spi_bdev; |
| 40 |
#define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1) |
| 41 |
#define MICROPY_HW_BDEV_SPIFLASH (&spi_bdev) |
| 42 |
#define MICROPY_HW_BDEV_SPIFLASH_CONFIG (&spiflash_config) |
| 43 |
#define MICROPY_HW_BDEV_SPIFLASH_SIZE_BYTES (MICROPY_HW_SPIFLASH_SIZE_BITS / 8) |
| 44 |
#define MICROPY_HW_BDEV_SPIFLASH_EXTENDED (&spi_bdev) // for extended block protocol |
| 45 |
|
| 46 |
#endif // !MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE |
| 47 |
|
| 48 |
// STM32 HSE config |
| 49 |
// The module has a 12 MHz crystal for the HSE oscillator. |
| 50 |
#define MICROPY_HW_CLK_PLLM (12) |
| 51 |
#define MICROPY_HW_CLK_PLLN (336) |
| 52 |
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) |
| 53 |
#define MICROPY_HW_CLK_PLLQ (7) |
| 54 |
#define MICROPY_HW_CLK_LAST_FREQ (1) |
| 55 |
|
| 56 |
// STM32 LSE config |
| 57 |
// The module has a 32.768 kHz crystal for the LSE (RTC). |
| 58 |
#define MICROPY_HW_RTC_USE_LSE (1) |
| 59 |
#define MICROPY_HW_RTC_USE_US (0) |
| 60 |
#define MICROPY_HW_RTC_USE_CALOUT (1) |
| 61 |
|
| 62 |
// UART2 config (MicroMod UART1) |
| 63 |
#define MICROPY_HW_UART2_NAME "UART1" |
| 64 |
#define MICROPY_HW_UART2_TX (pin_A2) |
| 65 |
#define MICROPY_HW_UART2_RX (pin_A3) |
| 66 |
|
| 67 |
// CAN1 config (MicroMod CAN) |
| 68 |
#define MICROPY_HW_CAN1_NAME "CAN" |
| 69 |
#define MICROPY_HW_CAN1_TX (pin_B9) |
| 70 |
#define MICROPY_HW_CAN1_RX (pin_B8) |
| 71 |
|
| 72 |
// I2C1 config (MicroMod I2C1) |
| 73 |
#define MICROPY_HW_I2C1_NAME "I2C1" |
| 74 |
#define MICROPY_HW_I2C1_SCL (pin_B6) |
| 75 |
#define MICROPY_HW_I2C1_SDA (pin_B7) |
| 76 |
|
| 77 |
// I2C2 config (MicroMod I2C) |
| 78 |
#define MICROPY_HW_I2C2_NAME "I2C" |
| 79 |
#define MICROPY_HW_I2C2_SCL (pin_B10) |
| 80 |
#define MICROPY_HW_I2C2_SDA (pin_B11) |
| 81 |
|
| 82 |
// SPI1 config (MicroMod SPI) |
| 83 |
#define MICROPY_HW_SPI1_NAME "SPI" |
| 84 |
#define MICROPY_HW_SPI1_NSS (pin_C4) |
| 85 |
#define MICROPY_HW_SPI1_SCK (pin_A5) |
| 86 |
#define MICROPY_HW_SPI1_MISO (pin_A6) |
| 87 |
#define MICROPY_HW_SPI1_MOSI (pin_A7) |
| 88 |
|
| 89 |
// LED1 config |
| 90 |
// The module has a single blue status LED. |
| 91 |
#define MICROPY_HW_LED1 (pin_A15) |
| 92 |
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin)) |
| 93 |
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin)) |
| 94 |
|
| 95 |
// USB device config |
| 96 |
#define MICROPY_HW_USB_FS (1) |