Debian Codegraph @

ports/stm32/boards/NUCLEO_F401RE/mpconfigboard.h

raw
1 #define MICROPY_HW_BOARD_NAME "NUCLEO-F401RE"
2 #define MICROPY_HW_MCU_NAME "STM32F401xE"
3
4 #define MICROPY_HW_HAS_SWITCH (1)
5 #define MICROPY_HW_HAS_FLASH (1)
6 #define MICROPY_HW_ENABLE_RTC (1)
7 #define MICROPY_HW_ENABLE_SERVO (1)
8
9 // HSE is 8MHz, HSI is 16MHz CPU freq set to 84MHz
10 // Default source for the clock is HSI.
11 // For revisions of the board greater than C-01, HSE can be used as a
12 // clock source by removing the #define MICROPY_HW_CLK_USE_HSE line
13 #define MICROPY_HW_CLK_USE_HSI (1)
14
15 #if MICROPY_HW_CLK_USE_HSI
16 #define MICROPY_HW_CLK_PLLM (16)
17 #else
18 #define MICROPY_HW_CLK_PLLM (8)
19 #endif
20 #define MICROPY_HW_CLK_PLLN (336)
21 #define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV4)
22 #define MICROPY_HW_CLK_PLLQ (7)
23
24 // UART config
25 #define MICROPY_HW_UART2_TX (pin_A2)
26 #define MICROPY_HW_UART2_RX (pin_A3)
27 #define MICROPY_HW_UART6_TX (pin_C6)
28 #define MICROPY_HW_UART6_RX (pin_C7)
29 // UART 2 connects to the STM32F103 (STLINK) on the Nucleo board
30 // and this is exposed as a USB Serial port.
31 #define MICROPY_HW_UART_REPL PYB_UART_2
32 #define MICROPY_HW_UART_REPL_BAUD 115200
33
34 // I2C buses
35 #define MICROPY_HW_I2C1_SCL (pin_B8) // Arduino D15, pin 3 on CN10
36 #define MICROPY_HW_I2C1_SDA (pin_B9) // D14, pin 5 on CN10
37 #define MICROPY_HW_I2C2_SCL (pin_B10) // Arduino D6, pin 25 on CN10
38 #define MICROPY_HW_I2C2_SDA (pin_B3) // Arduino D3, pin 31 on CN10
39 #define MICROPY_HW_I2C3_SCL (pin_A8) // Arduino D7, pin 23 on CN10
40 #define MICROPY_HW_I2C3_SDA (pin_C9) // pin 1 on CN10
41
42 // SPI buses
43 #define MICROPY_HW_SPI1_NSS (pin_A15) // pin 17 on CN7
44 #define MICROPY_HW_SPI1_SCK (pin_A5) // Arduino D13, pin 11 on CN10
45 #define MICROPY_HW_SPI1_MISO (pin_A6) // Arduino D12, pin 13 on CN10
46 #define MICROPY_HW_SPI1_MOSI (pin_A7) // Arduino D11, pin 15 on CN10
47
48 #define MICROPY_HW_SPI2_NSS (pin_B12) // pin 16 on CN10
49 #define MICROPY_HW_SPI2_SCK (pin_B13) // pin 30 on CN10
50 #define MICROPY_HW_SPI2_MISO (pin_B14) // pin 28 on CN10
51 #define MICROPY_HW_SPI2_MOSI (pin_B15) // pin 26 on CN10
52
53 #define MICROPY_HW_SPI3_NSS (pin_A4) // Arduino A2, pin 32 on CN7
54 #define MICROPY_HW_SPI3_SCK (pin_B3) // Arduino D3, pin 31 on CN10
55 #define MICROPY_HW_SPI3_MISO (pin_B4) // Arduino D5, pin 27 on CN10
56 #define MICROPY_HW_SPI3_MOSI (pin_B5) // Arduino D4, pin 29 on CN10
57
58 // USRSW is pulled low. Pressing the button makes the input go high.
59 #define MICROPY_HW_USRSW_PIN (pin_C13)
60 #define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
61 #define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
62 #define MICROPY_HW_USRSW_PRESSED (0)
63
64 // LEDs
65 #define MICROPY_HW_LED1 (pin_A5) // Green LD2 LED on Nucleo
66 #define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
67 #define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))