| 1 |
.\" Copyright, the authors of the Linux man-pages project |
| 2 |
.\" |
| 3 |
.\" SPDX-License-Identifier: GPL-1.0-or-later |
| 4 |
.\" |
| 5 |
.TH wavelan 4 2025-05-17 "Linux man-pages 6.18" |
| 6 |
.SH NAME |
| 7 |
wavelan \- AT&T GIS WaveLAN ISA device driver |
| 8 |
.SH SYNOPSIS |
| 9 |
.nf |
| 10 |
.BI "insmod wavelan_cs.o [io=" B,B.. "] [ irq=" I,I.. "] [name=" N,N.. ] |
| 11 |
.fi |
| 12 |
.SH DESCRIPTION |
| 13 |
.I This driver is obsolete: |
| 14 |
it was removed in Linux 2.6.35. |
| 15 |
.P |
| 16 |
.B wavelan |
| 17 |
is the low-level device driver for the NCR / AT&T / Lucent |
| 18 |
.B WaveLAN ISA |
| 19 |
and Digital (DEC) |
| 20 |
.B RoamAbout DS |
| 21 |
wireless ethernet adapter. |
| 22 |
This driver is available as a module or |
| 23 |
might be compiled in the kernel. |
| 24 |
This driver supports multiple cards |
| 25 |
in both forms (up to 4) and allocates the next available ethernet |
| 26 |
device (eth0..eth#) for each card found, unless a device name is |
| 27 |
explicitly specified (see below). |
| 28 |
This device name will be reported |
| 29 |
in the kernel log file with the MAC address, NWID, and frequency used |
| 30 |
by the card. |
| 31 |
.SS Parameters |
| 32 |
This section applies to the module form (parameters passed on the |
| 33 |
.BR insmod (8) |
| 34 |
command line). |
| 35 |
If the driver is included in the kernel, use the |
| 36 |
.I ether=IRQ,IO,NAME |
| 37 |
syntax on the kernel command line. |
| 38 |
.TP |
| 39 |
.B io |
| 40 |
Specify the list of base addresses where to search for wavelan cards |
| 41 |
(setting by dip switch on the card). |
| 42 |
If you don't specify any io |
| 43 |
address, the driver will scan 0x390 and 0x3E0 addresses, which might |
| 44 |
conflict with other hardware... |
| 45 |
.TP |
| 46 |
.B irq |
| 47 |
Set the list of IRQs that each wavelan card should use (the value is |
| 48 |
saved in permanent storage for future use). |
| 49 |
.TP |
| 50 |
.B name |
| 51 |
Set the list of names to be used for each wavelan card device (name |
| 52 |
used by |
| 53 |
.BR ifconfig (8)). |
| 54 |
.SS Wireless extensions |
| 55 |
Use |
| 56 |
.BR iwconfig (8) |
| 57 |
to manipulate wireless extensions. |
| 58 |
.SS NWID (or domain) |
| 59 |
Set the network ID |
| 60 |
.RI [ 0 |
| 61 |
to |
| 62 |
.IR FFFF ] |
| 63 |
or disable it |
| 64 |
.RI [ off ]. |
| 65 |
As the NWID is stored in the card Permanent Storage Area, it will be |
| 66 |
reused at any further invocation of the driver. |
| 67 |
.SS Frequency & channels |
| 68 |
For the 2.4\ GHz 2.00 Hardware, you are able to set the frequency by |
| 69 |
specifying one of the 10 defined channels |
| 70 |
.RI ( 2.412, |
| 71 |
.I 2.422, 2.425, 2.4305, 2.432, 2.442, 2.452, 2.460, 2.462 |
| 72 |
or |
| 73 |
.IR 2.484 ) |
| 74 |
or directly as a numeric value. |
| 75 |
The frequency is changed immediately and |
| 76 |
permanently. |
| 77 |
Frequency availability depends on the regulations... |
| 78 |
.SS Statistics spy |
| 79 |
Set a list of MAC addresses in the driver (up to 8) and get the last |
| 80 |
quality of link for each of those (see |
| 81 |
.BR iwspy (8)). |
| 82 |
.SS /proc/net/wireless |
| 83 |
.I status |
| 84 |
is the status reported by the modem. |
| 85 |
.I Link quality |
| 86 |
reports the quality of the modulation on the air (direct sequence |
| 87 |
spread spectrum) [max = 16]. |
| 88 |
.I Level |
| 89 |
and |
| 90 |
.I Noise |
| 91 |
refer to the signal level and noise level [max = 64]. |
| 92 |
The |
| 93 |
.I crypt discarded packet |
| 94 |
and |
| 95 |
.I misc discarded packet |
| 96 |
counters are not implemented. |
| 97 |
.SS Private ioctl |
| 98 |
You may use |
| 99 |
.BR iwpriv (8) |
| 100 |
to manipulate private ioctls. |
| 101 |
.SS Quality and level threshold |
| 102 |
Enables you to define the quality and level threshold used by the |
| 103 |
modem (packet below that level are discarded). |
| 104 |
.SS Histogram |
| 105 |
This functionality makes it possible to set a number of |
| 106 |
signal level intervals and |
| 107 |
to count the number of packets received in each of those defined |
| 108 |
intervals. |
| 109 |
This distribution might be used to calculate the mean value |
| 110 |
and standard deviation of the signal level. |
| 111 |
.SS Specific notes |
| 112 |
This driver fails to detect some |
| 113 |
.B non-NCR/AT&T/Lucent |
| 114 |
Wavelan cards. |
| 115 |
If this happens for you, you must look in the source code on |
| 116 |
how to add your card to the detection routine. |
| 117 |
.P |
| 118 |
Some of the mentioned features are optional. |
| 119 |
You may enable or disable |
| 120 |
them by changing flags in the driver header and recompile. |
| 121 |
.\" .SH AUTHOR |
| 122 |
.\" Bruce Janson \[em] [email protected] |
| 123 |
.\" .br |
| 124 |
.\" Jean Tourrilhes \[em] [email protected] |
| 125 |
.\" .br |
| 126 |
.\" (and others; see source code for details) |
| 127 |
.\" |
| 128 |
.\" SEE ALSO part |
| 129 |
.\" |
| 130 |
.SH SEE ALSO |
| 131 |
.BR wavelan_cs (4), |
| 132 |
.BR ifconfig (8), |
| 133 |
.BR insmod (8), |
| 134 |
.BR iwconfig (8), |
| 135 |
.BR iwpriv (8), |
| 136 |
.BR iwspy (8) |