| 1 |
The following are the cell names and cell descriptions of sample |
| 2 |
layouts designed at NIST for micromechanical designs. |
| 3 |
|
| 4 |
1. open-80x80 |
| 5 |
|
| 6 |
A MEMS test structure to check the progress of the EDP etchant |
| 7 |
on an intended 80 um x 80 um cavity. This design consists of a |
| 8 |
single open tile. |
| 9 |
|
| 10 |
2. open-oxide-80x80 |
| 11 |
|
| 12 |
An additional MEMS test structure to check the progress of |
| 13 |
the etchant on an intended 80 um x 80 um cavity with a |
| 14 |
trampoline-like suspended oxide. This design consists of |
| 15 |
four trapezoidal-shaped open tiles brought together in close |
| 16 |
vicinity such that the four cavities merge in the |
| 17 |
post-processing etch step creating one large 80 um x 80 um |
| 18 |
cavity with a suspended layer of oxide (see fig. 1). |
| 19 |
|
| 20 |
3. thermal-converter |
| 21 |
|
| 22 |
A polysilicon (poly1) heater with a metal1/poly1 thermopile |
| 23 |
used as an ac power sensor. |
| 24 |
|
| 25 |
4. thermal-actuator |
| 26 |
|
| 27 |
A cantilever structure consisting of poly1 with metal1 on |
| 28 |
top. These are connected at the end of the `diving board' |
| 29 |
and, when heated, the diving board bends upward due to the |
| 30 |
different thermal expansion coefficients of poly1 and |
| 31 |
metal1. |
| 32 |
|
| 33 |
5. pixel-80x80 |
| 34 |
|
| 35 |
A heating element with an 80 um x 80 um cavity. The heating |
| 36 |
element is made of meandering polysilicon (poly1) and is |
| 37 |
suspended over top of the cavity with its encompassing oxide |
| 38 |
after the anisotropic etch. |
| 39 |
|
| 40 |
6. pixel-160x160 |
| 41 |
|
| 42 |
Similar to the above structure but with a 160 um x 160 um |
| 43 |
cavity. |
| 44 |
|
| 45 |
7. micro-hot-plate |
| 46 |
|
| 47 |
The microhotplate design consists of: |
| 48 |
a. A meandering polysilicon (poly1) heating element with |
| 49 |
two external connections. |
| 50 |
b. An aluminum (metal1) plate with four external connections |
| 51 |
over top of the polysilicon (poly1) heating element. |
| 52 |
There is an oxide separating the poly1 and metal1. |
| 53 |
The heat is uniformly distributed across this metal1 |
| 54 |
plate with the metal1 resistance changing linearly with |
| 55 |
temperature. The metal1 sheet resistance at the |
| 56 |
various temperatures can be obtained with a |
| 57 |
van der Pauw measurement. |
| 58 |
|
| 59 |
8. gas-sensor |
| 60 |
|
| 61 |
The gas sensor design consists of the microhotplate design |
| 62 |
above with the addition of two layers: |
| 63 |
|
| 64 |
a. Four metal2 pads placed in the corners of the metal1 |
| 65 |
microhotplate (but not in contact with it). There |
| 66 |
are four external metal2 connections. |
| 67 |
b. Overglass openings centered on top of the metal2 pads. |
| 68 |
The metal2 pads and overglass openings allow a substance |
| 69 |
(e.g., tin oxide and palladium) to be placed on top of the |
| 70 |
whole pixel. When heated, the resistance of the substance |
| 71 |
changes in the presense of certain gases. The metal2 acts |
| 72 |
as a van der Pauw sheet resistor so the resistance change |
| 73 |
can be measured. This application of the microhotplate is |
| 74 |
called a gas sensor. (NIST has a patent pending on this |
| 75 |
gas sensor design.) |
| 76 |
|
| 77 |
|
| 78 |
|