| 1 |
<?php |
| 2 |
plugin_header(); |
| 3 |
|
| 4 |
$m = (strpos($PAGE, '_mono') > 0); |
| 5 |
?> |
| 6 |
|
| 7 |
<p> |
| 8 |
This plugin allows to add set of short delays of the original signal to the output mix. |
| 9 |
Each delay can be used to simulate the early reflections of the signal from walls. |
| 10 |
This allows to make the stereo image of the original signal wider, and the position |
| 11 |
of the source more definitive in the mix. Equalizers provided for each delay line allow to |
| 12 |
simulate the fading of the original signal. Every delay can be set in time, distance and |
| 13 |
musical time units. Also common pre-delay and time-stretching mechanisms are provided to allow |
| 14 |
the stereo image to change dynamically. Additionally, ramping mode is provided to smoothen |
| 15 |
change of delay on automation. |
| 16 |
</p> |
| 17 |
<p> |
| 18 |
Remember that for more realistic acoustic picture the more delay is the more low and high |
| 19 |
frequencies are cut from the delayed signal. |
| 20 |
</p> |
| 21 |
|
| 22 |
<p><b>'Master Channel' section:</b></p> |
| 23 |
<ul> |
| 24 |
<li> |
| 25 |
<b>Bypass</b> - bypass switch, when turned on (led indicator is shining), the output signal is similar to input signal. That does not mean |
| 26 |
that the delay line is not working. The delay line <u>always</u> collects input signal to prevent clicks or other noise when turning on. |
| 27 |
</li> |
| 28 |
<li><b>Temperature</b> - temperature of the air used for <b>Distance</b> delay calculation.</li> |
| 29 |
<li><b>Pre-delay</b> - pre-delay added to all delay lines relatively to the original signal.</li> |
| 30 |
<li><b>Tempo</b> - adjust tempo of the track.</li> |
| 31 |
<li><b>Tempo Sync</b> - synchronize tempo with host.</li> |
| 32 |
<li><b>Stretch</b> - time stretching, multiplicatively increases delay time for all delay lines.</li> |
| 33 |
<li><b>Settings</b> - different useful settings:</li> |
| 34 |
<ul> |
| 35 |
<li><b>Mono</b> - Output mono signal instead of stereo, useful for testing mono compatibility.</li> |
| 36 |
<li><b>Ramp</b> - Smoothen delay change for each processor (ramping), useful for smoothing automation effect.</li> |
| 37 |
<li><b>Tap</b> - Button that allows to adjust tempo by clicking it, useful when the tempo is not well known and needs to be detected.</li> |
| 38 |
</ul> |
| 39 |
<?php if ($m) {?> |
| 40 |
<li><b>Pan</b> - the panning applied to the original (dry) mono signal.</li> |
| 41 |
<?php } else {?> |
| 42 |
<li><b>Pan Left</b> - the panning applied to the left channel of the original (dry) signal.</li> |
| 43 |
<li><b>Pan Right</b> - the panning applied to the right channel of the original (dry) signal.</li> |
| 44 |
<li><b>Balance</b> - the balance between left and right channels of the original (dry) signal after panning.</li> |
| 45 |
<?php }?> |
| 46 |
<li><b>Dry</b> - the amount of dry (unprocessed) signal.</li> |
| 47 |
<li><b>Dry Mute</b> - mute the dry (unprocessed) signal.</li> |
| 48 |
<li><b>Wet</b> - the amount of wet (processed) signal.</li> |
| 49 |
<li><b>Wet Mute</b> - mute the wet (processed) signal.</li> |
| 50 |
<li><b>Dry/Wet</b> - the balance between unprocessed (dry) signal and mixed signal (see Dry, Dry Mute, Wet, Wet Mute controls).</li> |
| 51 |
<li><b>Output</b> - The overall output amplification of the signal.</li> |
| 52 |
</ul> |
| 53 |
|
| 54 |
<p><b>'Delay Lines' section:</b></p> |
| 55 |
<ul> |
| 56 |
<li><b>Delay lines</b> - the delay lines selector.</li> |
| 57 |
<li><b>Mode</b> - the delay calculation mode, available modes: <b>Off</b>, <b>Time</b>, <b>Distance</b>.</li> |
| 58 |
<li><b>S</b> - Soloing mode, mutes all non-soloing delay lines.</li> |
| 59 |
<li><b>M</b> - Mute mode, mutes selected delay line.</li> |
| 60 |
<li><b>P</b> - Inverts the phase of the delayed signal.</li> |
| 61 |
<li><b>Delay</b> - the delay assigned to the delay line.</li> |
| 62 |
<?php if ($m) {?> |
| 63 |
<li><b>Panorama</b> - the panning applied to the input signal for this delay line.</li> |
| 64 |
<?php } else {?> |
| 65 |
<li><b>Panorama Left</b> - the panning applied to the left channel of the input for this delay line.</li> |
| 66 |
<li><b>Panorama Right</b> - the panning applied to the right channel of the input for this delay line.</li> |
| 67 |
<li><b>Balance</b> - the balance between left and right channels of the input for this delay line after panning.</li> |
| 68 |
<?php }?> |
| 69 |
<li><b>Feedback</b> - the amount of feedback added to the signal.</li> |
| 70 |
<li><b>Gain</b> - the overall gain of this delay line.</li> |
| 71 |
<li><b>Filters</b> - allows to enable different filters:</li> |
| 72 |
<ul> |
| 73 |
<li><b>LC</b> - enables low-cut filter. |
| 74 |
<li><b>EQ</b> - enables 5-band equalizer. |
| 75 |
<li><b>HC</b> - enables high-cut filter. |
| 76 |
</ul> |
| 77 |
<li><b>Low cut</b> - the cut-off frequency of the low-cut filter with -24db/oct slope.</li> |
| 78 |
<li><b>Equalizer</b> - 5-band equalizer:</li> |
| 79 |
<ul> |
| 80 |
<li><b>Subs</b> - frequency band below 60 Hz. |
| 81 |
<li><b>Bass</b> - frequency band between 60 Hz and 300 Hz. |
| 82 |
<li><b>Middle</b> - frequency band between 300 Hz and 1 KHz. |
| 83 |
<li><b>Presence</b> - frequency band between 1 KHz and 6 KHz. |
| 84 |
<li><b>Treble</b> - frequency band above 6 KHz. |
| 85 |
</ul> |
| 86 |
<li><b>High cut</b> - the cut-off frequency of the high-cut filter with -24db/oct slope.</li> |
| 87 |
</ul> |