| 1 |
<?php |
| 2 |
plugin_header(); |
| 3 |
|
| 4 |
$s = (strpos($PAGE, '_stereo') > 0); |
| 5 |
?> |
| 6 |
<p> |
| 7 |
This plugin performs highly optimized real time zero-latency convolution |
| 8 |
to the input signal. It can be used as a cabinet emulator, some sort of equalizer |
| 9 |
or as a reverb simulation plugin. All what is needed is audio file with impulse |
| 10 |
response taken from the linear system (cabinet, equalizer or hall/room). |
| 11 |
</p> |
| 12 |
<p><b>Controls:</b></p> |
| 13 |
<ul> |
| 14 |
<li> |
| 15 |
<b>Bypass</b> - bypass switch, when turned on (led indicator is shining), the plugin bypasses signal (but still performs processing). |
| 16 |
</li> |
| 17 |
<li><b>FFT frame</b> - the maximum size of the FFT (Fast Fourier Transform) frame that can be used for time-continuous convolution</li> |
| 18 |
<?php if ($s) { ?> |
| 19 |
<li><b>File</b> - file selector, allows to load additional file that can be taken as impulse response for one of audio channels.</li> |
| 20 |
<?php } ?> |
| 21 |
<li><b>IR equalizer</b> - shows wet signal equalization overlay.</li> |
| 22 |
<li><b>Show</b> - Displays the additional <b>Wet Signal Equalization</b> section in the UI</li> |
| 23 |
<li><b>Reverse</b> - allows to reverse impulse file in time domain.</li> |
| 24 |
<li><b>Head cut</b> - cut amount of milliseconds from the beginning of the impulse files, can be used to remove early reflections of reverb.</li> |
| 25 |
<li><b>Tail cut</b> - cut amount of milliseconds from the end of the impulse files, can be used to remove large reverberation tail.</li> |
| 26 |
<li><b>Fade in</b> - adds additional fading at the beginning of the impulse file.</li> |
| 27 |
<li><b>Fade out</b> - adds additional fading at the end of the impulse file.</li> |
| 28 |
<li><b>Listen</b> - this button allows to play the preview of the audio file.</li> |
| 29 |
<li><b>Stop</b> - this button allows to stop the preview of the audio file.</li> |
| 30 |
<li><b>Source</b> - this combo allows to select file channel to use for the convolution.</li> |
| 31 |
<li><b>Active</b> - led that indicates that convolution is applied to the channel.</li> |
| 32 |
<li><b>Pre-delay</b> - amount of pre-delay added to the processed signal. |
| 33 |
<?php if ($s) {?> |
| 34 |
Can be used to individually control pre-delay of processed signal for each channel in the stereo pair that can |
| 35 |
provide additional stereo effect for reverbs. |
| 36 |
<?php } ?> |
| 37 |
</li> |
| 38 |
<li><b>Makeup</b> - amount of gain added to the processed signal. |
| 39 |
<?php if ($s) {?> |
| 40 |
Can be used to individually control amount of processed signal for each channel in the stereo pair. |
| 41 |
<?php } ?> |
| 42 |
</li> |
| 43 |
<li><b>Dry</b> - amount of gain applied to the dry (unprocessed) signal.</li> |
| 44 |
<li><b>Wet</b> - amount of gain additionally applied to the wet (processed) signal.</li> |
| 45 |
<li><b>Dry/Wet</b> - the balance between unprocessed (Dry) signal and mixed signal (see Dry and Wet controls).</li> |
| 46 |
<li><b>Output</b> - amount of gain additionally applied to the output signal.</li> |
| 47 |
</ul> |
| 48 |
|
| 49 |
<p><b>Wet Signal Equalization</b> overlay:</p> |
| 50 |
<ul> |
| 51 |
<li><b>Enabled</b> - enables wet (processed) signal equalization.</li> |
| 52 |
<?php if ($s) {?> |
| 53 |
<li><b>Stereo Split</b> - enables independent equalization of left and right channels.</li> |
| 54 |
<?php } ?> |
| 55 |
<li><b>Low-cut</b> - sets the slope of the high-pass butterworth filter, possible slopes are 12, 24 and 36 dB/octave.</li> |
| 56 |
<li><b>Low-cut freq</b> - the cutoff frequency of the high-pass butterworth filter.</li> |
| 57 |
<li><b>Faders</b> - faders that allow to change the loudness of eight corresponding frequency bands in range of -12..+12 dB</li> |
| 58 |
<li><b>High-cut</b> - sets the slope of the low-pass butterworth filter, possible slopes are 12, 24 and 36 dB/octave.</li> |
| 59 |
<li><b>High-cut freq</b> - the cutoff frequency of the low-pass butterworth filter.</li> |
| 60 |
</ul> |