| 1 |
<?php |
| 2 |
plugin_header(); |
| 3 |
|
| 4 |
$m = ($PAGE == 'comp_delay_mono') ? 'm' : ( |
| 5 |
($PAGE == 'comp_delay_stereo') ? 's' : ( |
| 6 |
($PAGE == 'comp_delay_x2_stereo') ? 'x2s' : |
| 7 |
null )); |
| 8 |
$c = ($m == 'm') ? ' the mono channel' : ( |
| 9 |
($m == 's') ? ' the stereo channel' : ( |
| 10 |
($m == 'x2s') ? ' each individual channel of the stereo channel' : |
| 11 |
null )); |
| 12 |
$n = ($m == 'x2s') ? 2 : 1; |
| 13 |
$cc = ($m == 'x2s') ? ' for the corresponding channel' : ''; |
| 14 |
$oc = ($m == 'x2s') ? ' of the corresponding channel' : ''; |
| 15 |
|
| 16 |
|
| 17 |
?> |
| 18 |
|
| 19 |
<p> |
| 20 |
This plugin allows to add short delay to<?= $c ?> to compensate the phase offset relatively to other channels. |
| 21 |
The main idea is to add some delay of the signal recorded by set of microphones placed at different positions and distances |
| 22 |
from the sound source. Because the speed of the sound is low (about 340 m/s), the signal from the sources placed on different |
| 23 |
position comes with different delays. When the receivers are placed on the different distances, the signal comes with different |
| 24 |
delays to them. So the final mix of the recorded tracks can sound muddy or, on the contrary, very thick. |
| 25 |
Note that even 1 centimeter of the difference can take the negative effect. To avoid this, you can add more delay to the receivers |
| 26 |
placed near the source and less delay to the receivers placed far from the source. This plugin helps to do this in three ways. |
| 27 |
In conjunction with <?php plugin_ref('phase_detector'); ?> you can very fast phase your sources. |
| 28 |
</p> |
| 29 |
|
| 30 |
<p><b>Controls:</b></p> |
| 31 |
<ul> |
| 32 |
<li> |
| 33 |
<b>Bypass</b> - bypass switch, when turned on (led indicator is shining), the output signal is similar to input signal. That does not mean |
| 34 |
that the delay line is not working. The delay line <u>always</u> collects input signal to prevent clicks or other noise when turning on. |
| 35 |
</li> |
| 36 |
<li><b>Output</b> - the loudness of the processed output signal<?= $cc ?>.</li> |
| 37 |
<li><b>Dry amount</b> - the amount of the unprocessed (dry) signal in the output signal<?= $cc ?>.</li> |
| 38 |
<li><b>Wet amount</b> - the amount of the processed (wet) signal in the output signal<?= $cc ?>.</li> |
| 39 |
<li><b>Dry/Wet</b> - the balance between mixed signal (see Dry Amount and Wet Amount knobs) and unprocessed (Dry) signal<?= $cc ?>.</li> |
| 40 |
<li> |
| 41 |
<b>Mode</b> - the switch button that selects active mode of the delay<?= $cc ?>: <b>Samples</b>, <b>Distance</b> or <b>Time</b>. When the mode is active, |
| 42 |
then the <b>Active</b> led of the appropriate control group is shining. |
| 43 |
</li> |
| 44 |
<li> |
| 45 |
<b>Ramp</b> - the button that enables ramping mode of the delay<?= $cc ?>. This feature allows to smooth delay jumps when applying automation by |
| 46 |
linearizing the delay change when processing audio. |
| 47 |
</li> |
| 48 |
<li><b>Samples</b> - sets the delay in samples for the <b>Samples</b> mode<?= $oc ?>.</li> |
| 49 |
<li><b>Meters</b> - inaccurate distance control, sets the distance in meters for the <b>Distance</b> mode<?= $oc ?>.</li> |
| 50 |
<li><b>Centimeters</b> - accurate distance control, sets the additional distance in centimeters for the <b>Distance</b> mode<?= $oc ?>.</li> |
| 51 |
<li><b>Temperature</b> - temperature of the air for the <b>Distance</b> mode<?= $oc ?>. <u>Note</u> that the speed of the sound in the air highly depends on the temperature of the air.</li> |
| 52 |
<li><b>Time</b> - the time to delay the input signal for the <b>Time</b> mode<?= $oc ?>.</li> |
| 53 |
</ul> |
| 54 |
|
| 55 |
<p><b>Indicators:</b></p> |
| 56 |
<ul> |
| 57 |
<li><b>Time</b> - the real delay (in time units) applied to input signal<?= $cc ?>.</li> |
| 58 |
<li><b>Samples</b> - the real number of samples the input signal was delayed<?= $cc ?>.</li> |
| 59 |
<li><b>Distance</b> - the real distance added to the receiver or the sound source<?= $cc ?>.</li> |
| 60 |
</ul> |
| 61 |
|
| 62 |
<p>The delay line always converts the parameters set in the active section into samples that are displayed on the <b>Samples</b> meter. |
| 63 |
All other metering values are converted from samples, so the real metering values may differ from the values set in the appropriate control group. |
| 64 |
</p> |