| 1 |
# libsensors configuration file |
| 2 |
# ----------------------------- |
| 3 |
# NOTE: |
| 4 |
# All the set statements from this file are commented out by default. |
| 5 |
# The reason is that the proper limits are highly system-dependent, |
| 6 |
# and writing improper limits may have all sorts of weird effects, |
| 7 |
# from beeping to CPU throttling to instant reboot. If you want to |
| 8 |
# actually set the limits, remove the comment marks, then run "sensors -s". |
| 9 |
# |
| 10 |
# This is a legacy example file. In general, configurations for new boards |
| 11 |
# should be placed in custom configuration files located in /etc/sensors.d. |
| 12 |
|
| 13 |
chip "lm78-*" "lm79-*" "w83781d-*" |
| 14 |
|
| 15 |
# These are as advised in the LM78 and LM79 data sheets, and used on almost |
| 16 |
# any mainboard we have seen. |
| 17 |
|
| 18 |
label in0 "VCore 1" |
| 19 |
label in1 "VCore 2" |
| 20 |
label in2 "+3.3V" |
| 21 |
label in3 "+5V" |
| 22 |
label in4 "+12V" |
| 23 |
label in5 "-12V" |
| 24 |
label in6 "-5V" |
| 25 |
|
| 26 |
# For positive voltages (in3, in4), two resistors are used, with the following |
| 27 |
# formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage) |
| 28 |
# R1 = R2 * (Vs/Vin - 1) |
| 29 |
# For negative voltages (in5, in6) two resistors are used, with the following |
| 30 |
# formula (Rin,Rf: resistor values, Vs: read voltage, Vin: pin voltage) |
| 31 |
# Rin = (Vs * Rf) / Vin |
| 32 |
# |
| 33 |
# Here are the official LM78 and LM79 data sheet values. |
| 34 |
# Vs R1,Rin R2,Rf Vin |
| 35 |
# in3 +5.0 6.8 10 +2.98 |
| 36 |
# in4 +12.0 30 10 +3.00 |
| 37 |
# in5 -12.0 240 60 +3.00 |
| 38 |
# in6 -5.0 100 60 +3.00 |
| 39 |
# |
| 40 |
# These would lead to these declarations: |
| 41 |
# compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 42 |
# compute in4 ((30/10)+1)*@ , @/((30/10)+1) |
| 43 |
# compute in5 -(240/60)*@ , -@/(240/60) |
| 44 |
# compute in6 -(100/60)*@ , -@/(100/60) |
| 45 |
# |
| 46 |
# On almost any mainboard we have seen, the Winbond compute values lead to |
| 47 |
# much better results, though. |
| 48 |
# |
| 49 |
# Vs R1,Rin R2,Rf Vin |
| 50 |
# in4 +12.0 28 10 +3.15 |
| 51 |
# in5 -12.0 210 60.4 +3.45 |
| 52 |
# in6 -5.0 90.9 60.4 +3.33 |
| 53 |
# |
| 54 |
# These leads to these declarations: |
| 55 |
|
| 56 |
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 57 |
compute in4 ((28/10)+1)*@ , @/((28/10)+1) |
| 58 |
compute in5 -(210/60.4)*@ , -@/(210/60.4) |
| 59 |
compute in6 -(90.9/60.4)*@ , -@/(90.9/60.4) |
| 60 |
|
| 61 |
# Here, we assume the VID readings are valid, and we use a max. 5% deviation |
| 62 |
|
| 63 |
# set in0_min cpu0_vid*0.95 |
| 64 |
# set in0_max cpu0_vid*1.05 |
| 65 |
# set in1_min cpu0_vid*0.95 |
| 66 |
# set in1_max cpu0_vid*1.05 |
| 67 |
# set in2_min 3.3 * 0.95 |
| 68 |
# set in2_max 3.3 * 1.05 |
| 69 |
# set in3_min 5.0 * 0.95 |
| 70 |
# set in3_max 5.0 * 1.05 |
| 71 |
# set in4_min 12 * 0.95 |
| 72 |
# set in4_max 12 * 1.05 |
| 73 |
# set in5_min -12 * 0.95 |
| 74 |
# set in5_max -12 * 1.05 |
| 75 |
# set in6_min -5 * 0.95 |
| 76 |
# set in6_max -5 * 1.05 |
| 77 |
|
| 78 |
# Examples for lm78, lm79 temperature limits |
| 79 |
# set temp1_max 40 |
| 80 |
# set temp1_max_hyst 37 |
| 81 |
|
| 82 |
# Examples for w83781d temperature limits |
| 83 |
# set temp1_max 40 |
| 84 |
# set temp1_max_hyst 37 |
| 85 |
# set temp2_max 52 |
| 86 |
# set temp2_max_hyst 47 |
| 87 |
# set temp3_max 52 |
| 88 |
# set temp3_max_hyst 47 |
| 89 |
|
| 90 |
# Examples of fan low speed limits |
| 91 |
# set fan1_min 3000 |
| 92 |
# set fan2_min 3000 |
| 93 |
# set fan3_min 3000 |
| 94 |
|
| 95 |
# Ignore fans you don't actually have |
| 96 |
# ignore fan1 |
| 97 |
# ignore fan2 |
| 98 |
# ignore fan3 |
| 99 |
|
| 100 |
# In case a lm78 is used together with a lm75, the lm78 temp sensor will |
| 101 |
# generally show the M/B temperature while the lm75 temp sensor will show |
| 102 |
# the CPU temperature. |
| 103 |
# label temp1 "M/B Temp" |
| 104 |
|
| 105 |
# Uncomment the following line to enable beeps for all alarms on this chip |
| 106 |
# set beep_enable 1 |
| 107 |
|
| 108 |
|
| 109 |
|
| 110 |
chip "lm75-*" |
| 111 |
|
| 112 |
# Most boards don't need scaling. Following is for the Asus TX97-E. |
| 113 |
# compute temp1 @*2.0, @/2.0 |
| 114 |
|
| 115 |
# Examples for temperature limits |
| 116 |
# set temp1_max 70 |
| 117 |
# set temp1_max_hyst 65 |
| 118 |
|
| 119 |
# In case a lm75 is used together with a lm78, the lm78 temp sensor will |
| 120 |
# generally show the M/B temperature while the lm75 temp sensor will show |
| 121 |
# the CPU temperature. |
| 122 |
# label temp1 "CPU Temp" |
| 123 |
|
| 124 |
|
| 125 |
chip "sis5595-*" |
| 126 |
|
| 127 |
label in0 "VCore 1" |
| 128 |
label in1 "VCore 2" |
| 129 |
label in2 "+3.3V" |
| 130 |
label in3 "+5V" |
| 131 |
label in4 "+12V" |
| 132 |
|
| 133 |
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 134 |
compute in4 ((28/10)+1)*@ , @/((28/10)+1) |
| 135 |
|
| 136 |
# set in0_min 2.0 * 0.95 |
| 137 |
# set in0_max 2.0 * 1.05 |
| 138 |
# set in1_min 2.0 * 0.95 |
| 139 |
# set in1_max 2.0 * 1.05 |
| 140 |
# set in2_min 3.3 * 0.95 |
| 141 |
# set in2_max 3.3 * 1.05 |
| 142 |
# set in3_min 5.0 * 0.95 |
| 143 |
# set in3_max 5.0 * 1.05 |
| 144 |
# set in4_min 12 * 0.95 |
| 145 |
# set in4_max 12 * 1.05 |
| 146 |
|
| 147 |
# |
| 148 |
# SiS5595 temperature calculation |
| 149 |
# The driver currently includes a calculation due to the wide |
| 150 |
# variation in thermistor types on SiS5595 motherboards. |
| 151 |
# The driver currently has a calculation of t = (.83x + 52.12). |
| 152 |
# One user reports the correct formula of t = (.345x - 12). |
| 153 |
# So you want to put a compute line in sensors.conf that has |
| 154 |
# the inverse of the driver formula, and put your formula on top of it. |
| 155 |
# The inverse of the driver formula is x = (1.20t - 62.77) |
| 156 |
# So the final formula is newt = (.345(1.20t - 62.77)) - 12). |
| 157 |
# Put this in the sensors.conf file as |
| 158 |
# compute temp1 ((.345 * ((1.20 * @) - 62.77)) - 12), ... |
| 159 |
# where ... is the inverse function I leave to you. |
| 160 |
# |
| 161 |
# Look in your 'Vendor.ini' file to see which one is present |
| 162 |
# on your motherboard. Look for the line like: |
| 163 |
# [Temp1] |
| 164 |
# ThermistorType = NTC-10KC15-1608-1P |
| 165 |
# Fix up a 'compute' line to match your thermistor type. |
| 166 |
# Warning. You still don't have enough information to do this. |
| 167 |
# ThermistorType = NTC-10KC15-1608-1P (10K at 25C; Beta = 3435) |
| 168 |
# compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ... |
| 169 |
# ThermistorType = NTC-103KC15-1608-1P (??) |
| 170 |
# compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ... |
| 171 |
# ThermistorType = NTC-103AT-2 (10K at 25C; Beta = 3435) |
| 172 |
# compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ... |
| 173 |
# ThermistorType = NTC-103JT (10K at 25C; Beta = 3435) |
| 174 |
# compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ... |
| 175 |
|
| 176 |
# examples for sis5595 temperature limits; |
| 177 |
# set temp1_max 40 |
| 178 |
# set temp1_max_hyst 37 |
| 179 |
|
| 180 |
|
| 181 |
chip "w83782d-*" "w83627hf-*" |
| 182 |
|
| 183 |
# Same as above for w83781d except that in5 and in6 are computed differently. |
| 184 |
# Rather than an internal inverting op amp, the 82d/83s use standard positive |
| 185 |
# inputs and the negative voltages are level shifted by a 3.6V reference. |
| 186 |
# The math is convoluted, so we hope that your motherboard |
| 187 |
# uses the recommended resistor values. |
| 188 |
|
| 189 |
label in0 "VCore 1" |
| 190 |
label in1 "VCore 2" |
| 191 |
label in2 "+3.3V" |
| 192 |
label in3 "+5V" |
| 193 |
label in4 "+12V" |
| 194 |
label in5 "-12V" |
| 195 |
label in6 "-5V" |
| 196 |
label in7 "V5SB" |
| 197 |
label in8 "VBat" |
| 198 |
|
| 199 |
# Abit BP6 motherboard has a few differences. VCore1 and VCore2 are the core |
| 200 |
# voltages of the two processors. Vtt is memory bus termination resistors |
| 201 |
# voltage. |
| 202 |
# label in1 "Vtt" |
| 203 |
# label in8 "VCore2" |
| 204 |
|
| 205 |
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 206 |
compute in4 ((28/10)+1)*@ , @/((28/10)+1) |
| 207 |
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14 |
| 208 |
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14 |
| 209 |
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 210 |
|
| 211 |
# set limits to 5% for the critical voltages |
| 212 |
# set limits to 10% for the non-critical voltages |
| 213 |
# set limits to 20% for the battery voltage |
| 214 |
|
| 215 |
# set in0_min cpu0_vid*0.95 |
| 216 |
# set in0_max cpu0_vid*1.05 |
| 217 |
# set in1_min cpu0_vid*0.95 |
| 218 |
# set in1_max cpu0_vid*1.05 |
| 219 |
# set in2_min 3.3 * 0.95 |
| 220 |
# set in2_max 3.3 * 1.05 |
| 221 |
# set in3_min 5.0 * 0.95 |
| 222 |
# set in3_max 5.0 * 1.05 |
| 223 |
# set in4_min 12 * 0.90 |
| 224 |
# set in4_max 12 * 1.10 |
| 225 |
# set in5_max -12 * 0.90 |
| 226 |
# set in5_min -12 * 1.10 |
| 227 |
# set in6_max -5 * 0.95 |
| 228 |
# set in6_min -5 * 1.05 |
| 229 |
# set in7_min 5 * 0.95 |
| 230 |
# set in7_max 5 * 1.05 |
| 231 |
# set in8_min 3.0 * 0.80 |
| 232 |
# set in8_max 3.0 * 1.20 |
| 233 |
|
| 234 |
# set up sensor types (thermistor is default) |
| 235 |
# 1 = PII/Celeron Diode; 2 = 3904 transistor; |
| 236 |
# 3435 = thermistor with Beta = 3435 |
| 237 |
# If temperature changes very little, try 1 or 2. |
| 238 |
# set temp1_type 1 |
| 239 |
# set temp2_type 2 |
| 240 |
# set temp3_type 3435 |
| 241 |
|
| 242 |
# examples for temperature limits |
| 243 |
# set temp1_max 40 |
| 244 |
# set temp1_max_hyst 37 |
| 245 |
# set temp2_max 52 |
| 246 |
# set temp2_max_hyst 47 |
| 247 |
# set temp3_max 52 |
| 248 |
# set temp3_max_hyst 47 |
| 249 |
|
| 250 |
|
| 251 |
chip "w83783s-*" |
| 252 |
|
| 253 |
# Same as above for w83781d except that in5 and in6 are computed differently. |
| 254 |
# Rather than an internal inverting op amp, the 82d/83s use standard positive |
| 255 |
# inputs and the negative voltages are level shifted by a 3.6V reference. |
| 256 |
# The math is convoluted, so we hope that your motherboard |
| 257 |
# uses the recommended resistor values. |
| 258 |
|
| 259 |
label in0 "VCore 1" |
| 260 |
label in2 "+3.3V" |
| 261 |
label in3 "+5V" |
| 262 |
label in4 "+12V" |
| 263 |
label in5 "-12V" |
| 264 |
label in6 "-5V" |
| 265 |
|
| 266 |
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 267 |
compute in4 ((28/10)+1)*@ , @/((28/10)+1) |
| 268 |
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14 |
| 269 |
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14 |
| 270 |
|
| 271 |
# set limits to 5% for the critical voltages |
| 272 |
# set limits to 10% for the non-critical voltages |
| 273 |
# set limits to 20% for the battery voltage |
| 274 |
|
| 275 |
# set in0_min cpu0_vid*0.95 |
| 276 |
# set in0_max cpu0_vid*1.05 |
| 277 |
# set in2_min 3.3 * 0.95 |
| 278 |
# set in2_max 3.3 * 1.05 |
| 279 |
# set in3_min 5.0 * 0.95 |
| 280 |
# set in3_max 5.0 * 1.05 |
| 281 |
# set in4_min 12 * 0.90 |
| 282 |
# set in4_max 12 * 1.10 |
| 283 |
# set in5_max -12 * 0.90 |
| 284 |
# set in5_min -12 * 1.10 |
| 285 |
# set in6_max -5 * 0.95 |
| 286 |
# set in6_min -5 * 1.05 |
| 287 |
|
| 288 |
# set up sensor types (thermistor is default) |
| 289 |
# 1 = PII/Celeron Diode; 2 = 3904 transistor; |
| 290 |
# 3435 = thermistor with Beta = 3435 |
| 291 |
# If temperature changes very little, try 1 or 2. |
| 292 |
# set temp1_type 1 |
| 293 |
# set temp2_type 2 |
| 294 |
|
| 295 |
# examples for temperature limits |
| 296 |
# set temp1_max 40 |
| 297 |
# set temp1_max_hyst 37 |
| 298 |
# set temp2_max 52 |
| 299 |
# set temp2_max_hyst 47 |
| 300 |
|
| 301 |
|
| 302 |
chip "w83697hf-*" |
| 303 |
|
| 304 |
# Same as above for w83781d except that in5 and in6 are computed differently. |
| 305 |
# Rather than an internal inverting op amp, the 82d/83s use standard positive |
| 306 |
# inputs and the negative voltages are level shifted by a 3.6V reference. |
| 307 |
# The math is convoluted, so we hope that your motherboard |
| 308 |
# uses the recommended resistor values. |
| 309 |
|
| 310 |
# no in1 on this chip. |
| 311 |
|
| 312 |
label in0 "VCore" |
| 313 |
label in2 "+3.3V" |
| 314 |
label in3 "+5V" |
| 315 |
label in4 "+12V" |
| 316 |
label in5 "-12V" |
| 317 |
label in6 "-5V" |
| 318 |
label in7 "V5SB" |
| 319 |
label in8 "VBat" |
| 320 |
|
| 321 |
# Tyan Trinity S2495 KT400 has a few differences. Thanks to Eric Schumann |
| 322 |
# for proving this information. Same is true for Epox 8K3A and 8KHA+. |
| 323 |
# Thanks to Thomas Schorpp for additional feedback. |
| 324 |
# label in2 "VAgp" |
| 325 |
# label in5 "+3.3V" # aka. Vio |
| 326 |
# label in6 "Vdimm" |
| 327 |
# label in7 "VBat" |
| 328 |
# label in8 "V5SB" |
| 329 |
# |
| 330 |
# You'll also want to comment out the in5 and in6 compute lines right below, |
| 331 |
# and rename compute in7 to compute in8. |
| 332 |
|
| 333 |
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 334 |
compute in4 ((28/10)+1)*@ , @/((28/10)+1) |
| 335 |
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14 |
| 336 |
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14 |
| 337 |
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 338 |
|
| 339 |
# 697HF does not have VID inputs so you MUST set your core |
| 340 |
# voltage limits below. Currently set for 1.8V core. |
| 341 |
# vvv |
| 342 |
|
| 343 |
# set in0_min 1.8 * 0.95 |
| 344 |
# set in0_max 1.8 * 1.05 |
| 345 |
|
| 346 |
# set in2_min 3.3 * 0.95 |
| 347 |
# set in2_max 3.3 * 1.05 |
| 348 |
# set in3_min 5.0 * 0.95 |
| 349 |
# set in3_max 5.0 * 1.05 |
| 350 |
# set in4_min 12 * 0.90 |
| 351 |
# set in4_max 12 * 1.10 |
| 352 |
# set in5_max -12 * 0.90 |
| 353 |
# set in5_min -12 * 1.10 |
| 354 |
# set in6_max -5 * 0.95 |
| 355 |
# set in6_min -5 * 1.05 |
| 356 |
# set in7_min 5 * 0.95 |
| 357 |
# set in7_max 5 * 1.05 |
| 358 |
# set in8_min 3.0 * 0.80 |
| 359 |
# set in8_max 3.0 * 1.20 |
| 360 |
|
| 361 |
# And for Tyan Trinity S2495 KT400 and Epox 8K3A and 8KHA+: |
| 362 |
# set in2_min 1.5 * 0.95 |
| 363 |
# set in2_max 1.5 * 1.05 |
| 364 |
# set in5_min 3.3 * 0.95 |
| 365 |
# set in5_max 3.3 * 1.05 |
| 366 |
# set in6_min 2.5 * 0.95 # 2.6 on Epox |
| 367 |
# set in6_max 2.5 * 1.05 # 2.6 on Epox |
| 368 |
# set in7_min 3.0 * 0.90 |
| 369 |
# set in7_max 3.0 * 1.10 |
| 370 |
# set in8_min 5 * 0.90 |
| 371 |
# set in8_max 5 * 1.10 |
| 372 |
|
| 373 |
# set up sensor types (thermistor is default) |
| 374 |
# 1 = PII/Celeron Diode; 2 = 3904 transistor; |
| 375 |
# 3435 = thermistor with Beta = 3435 |
| 376 |
# If temperature changes very little, try 1 or 2. |
| 377 |
# set temp1_type 1 |
| 378 |
# set temp2_type 2 |
| 379 |
# set temp3_type 3435 |
| 380 |
|
| 381 |
# examples for temperature limits |
| 382 |
# set temp1_max 40 |
| 383 |
# set temp1_max_hyst 37 |
| 384 |
# set temp2_max 52 |
| 385 |
# set temp2_max_hyst 47 |
| 386 |
|
| 387 |
|
| 388 |
chip "w83627thf-*" "w83637hf-*" |
| 389 |
|
| 390 |
# Rather than an internal inverting op amp, the 627thf uses standard positive |
| 391 |
# inputs and the negative voltages are level shifted by a 3.6V reference |
| 392 |
# (same as 82d/83s). |
| 393 |
# The math is convoluted, so we hope that your motherboard |
| 394 |
# uses the recommended resistor values. |
| 395 |
# Note that in1 (+12V) is the usual in4, and in4 (-12V) is the usual in5. |
| 396 |
# Data sheet is obviously wrong for in4, the usual formula should work. |
| 397 |
# No in5 nor in6. |
| 398 |
|
| 399 |
label in0 "VCore" |
| 400 |
label in1 "+12V" |
| 401 |
label in2 "+3.3V" |
| 402 |
label in3 "+5V" |
| 403 |
label in4 "-12V" |
| 404 |
label in7 "V5SB" |
| 405 |
label in8 "VBat" |
| 406 |
|
| 407 |
# Mori Hiroyuki reported to need this (P4P800) |
| 408 |
# compute in0 @/2, @*2 |
| 409 |
|
| 410 |
compute in1 ((28/10)+1)*@, @/((28/10)+1) |
| 411 |
compute in3 ((34/51)+1)*@, @/((34/51)+1) |
| 412 |
compute in4 (5.14*@)-14.91, (@+14.91)/5.14 |
| 413 |
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 414 |
|
| 415 |
# set limits to 5% for the critical voltages |
| 416 |
# set limits to 10% for the non-critical voltages |
| 417 |
# set limits to 20% for the battery voltage |
| 418 |
# if your vid is wrong, you'll need to adjust in0_min and in0_max |
| 419 |
|
| 420 |
# set in0_min cpu0_vid * 0.95 |
| 421 |
# set in0_max cpu0_vid * 1.05 |
| 422 |
# set in1_min 12 * 0.90 |
| 423 |
# set in1_max 12 * 1.10 |
| 424 |
# set in2_min 3.3 * 0.95 |
| 425 |
# set in2_max 3.3 * 1.05 |
| 426 |
# set in3_min 5.0 * 0.95 |
| 427 |
# set in3_max 5.0 * 1.05 |
| 428 |
# set in4_min -12 * 1.10 |
| 429 |
# set in4_max -12 * 0.90 |
| 430 |
# set in7_min 5 * 0.95 |
| 431 |
# set in7_max 5 * 1.05 |
| 432 |
# set in8_min 3.0 * 0.80 |
| 433 |
# set in8_max 3.0 * 1.20 |
| 434 |
|
| 435 |
# set up sensor types (thermistor is default) |
| 436 |
# 1 = PII/Celeron Diode; 2 = 3904 transistor; |
| 437 |
# 3435 = thermistor with Beta = 3435 |
| 438 |
# If temperature changes very little, try 1 or 2. |
| 439 |
# set temp1_type 1 |
| 440 |
# set temp2_type 2 |
| 441 |
# set temp3_type 3435 |
| 442 |
|
| 443 |
label temp1 "M/B Temp" |
| 444 |
label temp2 "CPU Temp" |
| 445 |
# ignore temp3 |
| 446 |
|
| 447 |
# examples for temperature limits |
| 448 |
# set temp1_max 40 |
| 449 |
# set temp1_max_hyst 37 |
| 450 |
# set temp2_max 52 |
| 451 |
# set temp2_max_hyst 47 |
| 452 |
# set temp3_max 52 |
| 453 |
# set temp3_max_hyst 47 |
| 454 |
|
| 455 |
# ignore fan1 |
| 456 |
label fan2 "CPU Fan" |
| 457 |
# ignore fan3 |
| 458 |
|
| 459 |
|
| 460 |
# Here are configurations for Winbond W83792AD/D chip. |
| 461 |
chip "w83792d-*" |
| 462 |
|
| 463 |
label in0 "VCoreA" |
| 464 |
label in1 "VCoreB" |
| 465 |
label in6 "5VCC" |
| 466 |
label in7 "5VSB" |
| 467 |
label in8 "VBAT" |
| 468 |
|
| 469 |
# set in0_min 1.4 |
| 470 |
# set in0_max 1.6 |
| 471 |
# set in1_min 1.4 |
| 472 |
# set in1_max 1.6 |
| 473 |
# set in2_min 3.2 |
| 474 |
# set in2_max 3.4 |
| 475 |
# set in3_min 3.1 |
| 476 |
# set in3_max 3.3 |
| 477 |
# set in4_min 1.4 |
| 478 |
# set in4_max 1.5 |
| 479 |
# set in5_min 2.6 |
| 480 |
# set in5_max 2.65 |
| 481 |
# set in6_min 5 * 0.95 |
| 482 |
# set in6_max 5 * 1.05 |
| 483 |
# set in7_min 5 * 0.95 |
| 484 |
# set in7_max 5 * 1.05 |
| 485 |
# set in8_min 3 * 0.95 |
| 486 |
# set in8_max 3 * 1.05 |
| 487 |
|
| 488 |
# fan1 adjustments examples |
| 489 |
|
| 490 |
# set fan1_div 4 |
| 491 |
# set fan1_min 1500 |
| 492 |
|
| 493 |
# temp2 limits examples |
| 494 |
|
| 495 |
# set temp2_max 42 |
| 496 |
# set temp2_max_hyst 37 |
| 497 |
|
| 498 |
# ignore examples |
| 499 |
|
| 500 |
# ignore fan7 |
| 501 |
# ignore temp3 |
| 502 |
|
| 503 |
|
| 504 |
# Here are configurations for Winbond W83793 chip. |
| 505 |
chip "w83793-*" |
| 506 |
|
| 507 |
label in0 "VCoreA" |
| 508 |
label in1 "VCoreB" |
| 509 |
label in2 "Vtt" |
| 510 |
label in5 "+3.3V" |
| 511 |
label in6 "+12V" |
| 512 |
label in7 "+5V" |
| 513 |
label in8 "5VSB" |
| 514 |
label in9 "VBAT" |
| 515 |
|
| 516 |
compute in6 12*@ , @/12 |
| 517 |
|
| 518 |
label temp1 "CPU1 Temp" |
| 519 |
label temp2 "CPU2 Temp" |
| 520 |
|
| 521 |
# fan1 adjustments examples |
| 522 |
|
| 523 |
# set fan1_min 1500 |
| 524 |
|
| 525 |
# temp2 limits examples |
| 526 |
|
| 527 |
# set temp2_max 45 |
| 528 |
# set temp2_max_hyst 40 |
| 529 |
|
| 530 |
# ignore examples |
| 531 |
|
| 532 |
# ignore fan7 |
| 533 |
# ignore temp3 |
| 534 |
|
| 535 |
|
| 536 |
chip "as99127f-*" |
| 537 |
|
| 538 |
# Asus won't release a datasheet so this is guesswork. |
| 539 |
# Thanks to Guntram Blohm, Jack, Ed Harrison, Artur Gawryszczak, |
| 540 |
# Victor G. Marimon and others for their feedback. |
| 541 |
|
| 542 |
# Dual power plane |
| 543 |
label in0 "VCore 1" |
| 544 |
label in1 "VCore 2" |
| 545 |
# Single power plane (A7V133, A7M266, CUV4X) |
| 546 |
# label in0 "VCore" |
| 547 |
# ignore in1 |
| 548 |
|
| 549 |
label in2 "+3.3V" |
| 550 |
label in3 "+5V" |
| 551 |
label in4 "+12V" |
| 552 |
# These last two may not make sense on all motherboards. |
| 553 |
label in5 "-12V" |
| 554 |
label in6 "-5V" |
| 555 |
|
| 556 |
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 557 |
compute in4 ((28/10)+1)*@ , @/((28/10)+1) |
| 558 |
# AS99127F rev.1 (same as w83781d) |
| 559 |
compute in5 -(240/60.4)*@ , -@/(240/60.4) |
| 560 |
compute in6 -(90.9/60.4)*@ , -@/(90.9/60.4) |
| 561 |
# AS99127F rev.2 (same as w83782d) |
| 562 |
# compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14 |
| 563 |
# compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14 |
| 564 |
|
| 565 |
# Depending on your motherboard, you may have to use any of two formulae |
| 566 |
# for temp2. Quoting Artur Gawryszczak (edited to reflect subsequent fixes |
| 567 |
# to the driver): |
| 568 |
# "I guess, that the formula "(@*15/43)+25, (@-25)*43/15" is correct |
| 569 |
# for those Asus motherboards, which get CPU temperature from internal |
| 570 |
# thermal diode (Pentium Coppermine, and above), while no formula is needed |
| 571 |
# for Athlon/Duron boards, which use a thermistor in the socket." |
| 572 |
# An alternative formula was then found and reported by Victor G. Marimon. |
| 573 |
|
| 574 |
# Asus A7V133, Asus A7M266 |
| 575 |
# No compute line is needed |
| 576 |
# Asus CUV4X, Asus A7V8X |
| 577 |
# compute temp2 (@*15/43)+25, (@-25)*43/15 |
| 578 |
# Asus CUSL2, Asus CUV266-DLS, Asus TUSL2-C |
| 579 |
# compute temp2 (@*30/43)+25, (@-25)*43/30 |
| 580 |
|
| 581 |
# See comments above if temp3 looks bad. What works for temp2 is likely |
| 582 |
# to work for temp3 for dual-CPU boards, such as the CUV4X-D. |
| 583 |
|
| 584 |
# Most Asus boards have temperatures settled like that: |
| 585 |
label temp1 "M/B Temp" |
| 586 |
label temp2 "CPU Temp" |
| 587 |
# However, some boards have them swapped (A7N8X Deluxe rev.2, |
| 588 |
# A7N8X-E Deluxe rev.2, CUV4X): |
| 589 |
# label temp1 "CPU Temp" |
| 590 |
# label temp2 "M/B Temp" |
| 591 |
|
| 592 |
# Most boards have no temp3 by default, except for dual-CPU boards. |
| 593 |
# label temp3 "CPU 2 Temp" |
| 594 |
# ignore temp3 |
| 595 |
|
| 596 |
# set limits to 5% for the critical voltages |
| 597 |
# set limits to 10% for the non-critical voltages |
| 598 |
# set limits to 20% for the battery voltage |
| 599 |
|
| 600 |
# set in0_min cpu0_vid*0.95 |
| 601 |
# set in0_max cpu0_vid*1.05 |
| 602 |
# set in1_min cpu0_vid*0.95 |
| 603 |
# set in1_max cpu0_vid*1.05 |
| 604 |
# set in2_min 3.3 * 0.95 |
| 605 |
# set in2_max 3.3 * 1.05 |
| 606 |
# set in3_min 5.0 * 0.95 |
| 607 |
# set in3_max 5.0 * 1.05 |
| 608 |
# set in4_min 12 * 0.90 |
| 609 |
# set in4_max 12 * 1.10 |
| 610 |
# set in5_min -12 * 0.90 |
| 611 |
# set in5_max -12 * 1.10 |
| 612 |
# set in6_min -5 * 0.95 |
| 613 |
# set in6_max -5 * 1.05 |
| 614 |
|
| 615 |
# examples for temperature limits |
| 616 |
# set temp1_max 40 |
| 617 |
# set temp1_max_hyst 37 |
| 618 |
# set temp2_max 52 |
| 619 |
# set temp2_max_hyst 47 |
| 620 |
# set temp3_max 52 |
| 621 |
# set temp3_max_hyst 47 |
| 622 |
|
| 623 |
|
| 624 |
chip "gl518sm-*" |
| 625 |
|
| 626 |
# IMPORTANT: in0, in1, and in2 values (+5, +3, and +12) CANNOT be read |
| 627 |
# |
| 628 |
# Factors and labels taken from GL518SM datasheet, they seem to give |
| 629 |
# reasonable values with EISCA connected Fan78 |
| 630 |
|
| 631 |
label in0 "+5V" |
| 632 |
label in1 "+3.3V" |
| 633 |
label in2 "+12V" |
| 634 |
label in3 "Vcore" |
| 635 |
|
| 636 |
# in2 depends on external resistors (4,7k and 15k assumed here) |
| 637 |
# in1 and in3 require no scaling |
| 638 |
|
| 639 |
compute in2 (197/47)*@ , @/(197/47) |
| 640 |
|
| 641 |
# set in0_min 4.8 |
| 642 |
# set in0_max 5.2 |
| 643 |
# set in1_min 3.20 |
| 644 |
# set in1_max 3.40 |
| 645 |
# set in2_min 11.0 |
| 646 |
# set in2_max 13.0 |
| 647 |
# set in3_min 2.10 |
| 648 |
# set in3_max 2.30 |
| 649 |
# set fan2_min 0 |
| 650 |
|
| 651 |
|
| 652 |
chip "gl520sm-*" |
| 653 |
|
| 654 |
# Factors and labels taken from GL520SM datasheet |
| 655 |
|
| 656 |
# The GL520SM has two application modes. In mode 1 it has two thermistor |
| 657 |
# inputs, in mode 2 it has only one and an extra (negative) voltage input. |
| 658 |
# The mode is supposed to be set properly by your BIOS so you should not |
| 659 |
# need to change it. Note that you have either temp2 or in4, not both. |
| 660 |
|
| 661 |
label in0 "+5V" |
| 662 |
label in1 "+3.3V" |
| 663 |
label in2 "+12V" |
| 664 |
label in3 "Vcore" |
| 665 |
label in4 "-12V" |
| 666 |
|
| 667 |
# in1 and in3 require no scaling |
| 668 |
# in2 depends on external resistors (4,7k and 15k assumed) |
| 669 |
|
| 670 |
# in4 = ((R1+R2)/R2)*@ - (R1/R2)*vdd |
| 671 |
# |
| 672 |
# -12 --| R1 |---t---| R2 |-- +5 |
| 673 |
# | |
| 674 |
# vin4 |
| 675 |
# |
| 676 |
|
| 677 |
compute in2 (197/47)*@ , @/(197/47) |
| 678 |
compute in4 (5*@)-(4*in0_input) , (@+4*in0_input)/5 |
| 679 |
|
| 680 |
# set in0_min 4.8 |
| 681 |
# set in0_max 5.2 |
| 682 |
# set in1_min 3.20 |
| 683 |
# set in1_max 3.40 |
| 684 |
# set in2_min 11.0 |
| 685 |
# set in2_max 13.0 |
| 686 |
# set in3_min 2.10 |
| 687 |
# set in3_max 2.30 |
| 688 |
|
| 689 |
|
| 690 |
chip "lm80-*" |
| 691 |
|
| 692 |
# The values below should be correct if you own a qdi BX (brilliant1) |
| 693 |
# mainboard. Many thanks go to Peter T. Breuer for helping us figure |
| 694 |
# out how to handle the LM80. |
| 695 |
|
| 696 |
# For positive voltages (in0..in4), two resistors are used, with the following |
| 697 |
# formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage) |
| 698 |
# R1 = R2 * (Vs/Vin - 1) |
| 699 |
# For negative voltages (in5, in6) two resistors are used, with the following |
| 700 |
# formula (R3,R4: resistor values, Vs: read voltage, Vin: pin voltage, |
| 701 |
# V5: +5V) |
| 702 |
# R3 = R4 * (Vs - Vin) / (Vin - V5) |
| 703 |
|
| 704 |
# Here are the official LM80 data sheet values. |
| 705 |
# Vs R1,R3 R2,R4 Vin |
| 706 |
# +2.5V 23.7 75 +1.9 |
| 707 |
# +3.3V 22.1 30 +1.9 |
| 708 |
# +5.0 24 14.7 +1.9 |
| 709 |
# +12.0 160 30.1 +1.9 |
| 710 |
# -12.0 160 35.7 +1.9 |
| 711 |
# -5.0 36 16.2 +1.9 |
| 712 |
|
| 713 |
# Now curiously enough, VCore is connected with (unknown) resistors, which |
| 714 |
# translate a +2.8V to +1.9V. So we use that in the computations below. |
| 715 |
|
| 716 |
label in0 "+5V" |
| 717 |
label in1 "VTT" |
| 718 |
label in2 "+3.3V" |
| 719 |
label in3 "+Vcore" |
| 720 |
label in4 "+12V" |
| 721 |
label in5 "-12V" |
| 722 |
label in6 "-5V" |
| 723 |
|
| 724 |
compute in0 (24/14.7 + 1) * @ , @ / (24/14.7 + 1) |
| 725 |
compute in2 (22.1/30 + 1) * @ , @ / (22.1/30 + 1) |
| 726 |
compute in3 (2.8/1.9) * @, @ * 1.9/2.8 |
| 727 |
compute in4 (160/30.1 + 1) * @, @ / (160/30.1 + 1) |
| 728 |
compute in5 (160/35.7)*(@ - in0_input) + @, (@ + in0_input * 160/35.7)/ (1 + 160/35.7) |
| 729 |
compute in6 (36/16.2)*(@ - in0_input) + @, (@ + in0_input * 36/16.2) / (1 + 36/16.2) |
| 730 |
|
| 731 |
# set in0_min 5 * 0.95 |
| 732 |
# set in0_max 5 * 1.05 |
| 733 |
# What is your VTT? It is probably not this value... |
| 734 |
# set in1_min 2*0.95 |
| 735 |
# set in1_max 2*1.05 |
| 736 |
# set in2_min 3.3 * 0.95 |
| 737 |
# set in2_max 3.3 * 1.05 |
| 738 |
# What is your VCore? It is probably not this value... |
| 739 |
# set in3_min 1.9 * 0.95 |
| 740 |
# set in3_max 1.9 * 1.05 |
| 741 |
# set in4_min 12 * 0.95 |
| 742 |
# set in4_max 12 * 1.05 |
| 743 |
# set in5_min -12 * 1.05 |
| 744 |
# set in5_max -12 * 0.95 |
| 745 |
# set in6_min -5 * 1.05 |
| 746 |
# set in6_max -5 * 0.95 |
| 747 |
|
| 748 |
# All 4 of these limits apply to the single temperature sensor. |
| 749 |
# "crit" may or may not do anything on your motherboard but it should |
| 750 |
# be set higher than the "max" thresholds. |
| 751 |
# set temp1_max 52 |
| 752 |
# set temp1_max_hyst 45 |
| 753 |
# set temp1_crit 62 |
| 754 |
# set temp1_crit_hyst 57 |
| 755 |
|
| 756 |
|
| 757 |
chip "via686a-*" |
| 758 |
|
| 759 |
# VIA is very specific about the voltage sensor inputs, and our labels |
| 760 |
# reflect what they say. Unfortunately, they are not at all specific about |
| 761 |
# how to convert any of the register values to real units. Fortunately, |
| 762 |
# Jonathan Yew and Alex van Kaam came through with some data for temp |
| 763 |
# conversion and formulae for voltage conversion. However, the conversions |
| 764 |
# should be regarded as our best guess - YMMV. |
| 765 |
|
| 766 |
# On the Tyan S1598, the 2.5V sensor reads 0 and is not displayed in the BIOS. |
| 767 |
# Linas Vepstas reports that this sensor shows nothing of |
| 768 |
# interest on the Abit KA7 (Athlon), and is also not displayed in the BIOS. |
| 769 |
# Likewise, Johannes Drechsel-Burkhard reports that this |
| 770 |
# sensor is unavailable in the BIOS of his MSI K7T Pro (Thunderbird). So, |
| 771 |
# if you have one of these boards you may want to uncomment the 'ignore in1' |
| 772 |
# line below. |
| 773 |
|
| 774 |
label in0 "CPU core" |
| 775 |
label in1 "+2.5V" |
| 776 |
#ignore in1 |
| 777 |
label in2 "I/O" |
| 778 |
label in3 "+5V" |
| 779 |
label in4 "+12V" |
| 780 |
|
| 781 |
label fan1 "CPU Fan" |
| 782 |
label fan2 "P/S Fan" |
| 783 |
|
| 784 |
# VIA suggests that temp3 is an internal temp sensor for the 686a. However, |
| 785 |
# on the Tyan S1598 as well as the Abit KA7 (Athalon), the absolute values |
| 786 |
# of the readings from that sensor are not valid. The readings do seem to |
| 787 |
# correlate with temp changes, but the conversion factor may be quite |
| 788 |
# different from temp1 & temp2 (as noted above, VIA has not provided |
| 789 |
# conversion info). So, you may wish to 'ignore temp3'. |
| 790 |
|
| 791 |
# Johannes Drechsel-Burkhard notes that on his MSI K7T Pro, |
| 792 |
# temp1 is the CPU temp and temp2 is the SYS temp. Hugo van der Merwe notes |
| 793 |
# the same for his Gigabyte GA-7DXC, Olivier Martin for his Gigabyte |
| 794 |
# GA-7ZM and Patrick Thomson for his Chaintech CT-5ATA. |
| 795 |
# Thomas Anglmaier notes: on Epox EP-7kxa temp2 is CPU and temp1 is SYS. |
| 796 |
|
| 797 |
label temp1 "SYS Temp" |
| 798 |
label temp2 "CPU Temp" |
| 799 |
label temp3 "SBr Temp" |
| 800 |
#ignore temp3 |
| 801 |
|
| 802 |
# Set your CPU core limits here if the BIOS did not. |
| 803 |
|
| 804 |
#set in0_min 1.70 * 0.95 |
| 805 |
#set in0_max 1.70 * 1.05 |
| 806 |
|
| 807 |
# Other voltage values are standard so we can enforce the limits. |
| 808 |
|
| 809 |
# set in1_min 2.5 * 0.95 |
| 810 |
# set in1_max 2.5 * 1.05 |
| 811 |
# set in2_min 3.3 * 0.95 |
| 812 |
# set in2_max 3.3 * 1.05 |
| 813 |
# set in3_min 5 * 0.9 |
| 814 |
# set in3_max 5 * 1.1 |
| 815 |
# set in4_min 12 * 0.9 |
| 816 |
# set in4_max 12 * 1.1 |
| 817 |
|
| 818 |
# Set your temp limits here. Remember, 'tempX_max' is the temp at which an |
| 819 |
# alarm is triggered, and 'tempX_max_hyst' is the temp at which an alarm turns off. |
| 820 |
# Setting tempX_max_hyst to a few degrees below the corresponding tempX_max |
| 821 |
# prevents an oscillation between alarm on and off states. This kind of |
| 822 |
# oscillation is known as hyteresis, thus the name. (You typically get the |
| 823 |
# most serious and troublesome hysteresis when a sensor triggers something to |
| 824 |
# reduce the temp, thus creating a negative feedback loop. Even without that, |
| 825 |
# we would still get some oscillation when the temp hovers around the limit |
| 826 |
# due to noise.) |
| 827 |
|
| 828 |
# set temp1_max 45 |
| 829 |
# set temp1_max_hyst 40 |
| 830 |
# set temp2_max 60 |
| 831 |
# set temp2_max_hyst 55 |
| 832 |
# set temp3_max 65 |
| 833 |
# set temp3_max_hyst 60 |
| 834 |
|
| 835 |
# You could set your fan limits too, but the defaults should be fine. |
| 836 |
|
| 837 |
#set fan1_min 5000 |
| 838 |
#set fan2_min 5000 |
| 839 |
|
| 840 |
|
| 841 |
chip "adm1025-*" "ne1619-*" |
| 842 |
|
| 843 |
# The ADM1025 has integrated scaling resistors, rather |
| 844 |
# than external resistors common to most sensor devices. |
| 845 |
# These apply to the 6 voltage inputs in0-in5 (+2.5V, VCore, |
| 846 |
# +3.3V, +5V, +12V, VCC). As the scaling is fixed inside |
| 847 |
# the chip for these inputs, it is fairly certain that the |
| 848 |
# motherboard connections match these labels, and that the |
| 849 |
# driver computations are correct. Therefore they do not need to |
| 850 |
# be overridden here. |
| 851 |
|
| 852 |
label in0 "+2.5V" |
| 853 |
label in1 "VCore" |
| 854 |
label in2 "+3.3V" |
| 855 |
label in3 "+5V" |
| 856 |
label in4 "+12V" |
| 857 |
label in5 "VCC" |
| 858 |
|
| 859 |
# Tolerate a 5% deviance for CPU power-supply |
| 860 |
# set in1_min cpu0_vid * 0.95 |
| 861 |
# set in1_max cpu0_vid * 1.05 |
| 862 |
# Tolerate a 10% deviance for other voltages |
| 863 |
# set in0_min 2.5 * 0.90 |
| 864 |
# set in0_max 2.5 * 1.10 |
| 865 |
# set in2_min 3.3 * 0.90 |
| 866 |
# set in2_max 3.3 * 1.10 |
| 867 |
# set in3_min 5.0 * 0.90 |
| 868 |
# set in3_max 5.0 * 1.10 |
| 869 |
# set in4_min 12 * 0.90 |
| 870 |
# set in4_max 12 * 1.10 |
| 871 |
# set in5_min 3.3 * 0.90 |
| 872 |
# set in5_max 3.3 * 1.10 |
| 873 |
|
| 874 |
# Depending on how your chipset is hardwired, you may or may not have |
| 875 |
# +12V readings (will show as 0.0V if you don't have it). |
| 876 |
# ignore in4 |
| 877 |
|
| 878 |
# VCC is the power-supply voltage of the ADM1025 chipset, generally |
| 879 |
# redundant with +3.3V so you may want to hide it. |
| 880 |
# ignore in5 |
| 881 |
|
| 882 |
# Temperatures |
| 883 |
label temp1 "CPU Temp" |
| 884 |
label temp2 "M/B Temp" |
| 885 |
# set temp1_min 10 |
| 886 |
# set temp1_max 60 |
| 887 |
# set temp2_min 10 |
| 888 |
# set temp2_max 45 |
| 889 |
|
| 890 |
|
| 891 |
chip "lm87-*" "adm1024-*" |
| 892 |
# |
| 893 |
# The LM87 has integrated scaling resistors, rather |
| 894 |
# than external resistors common to most sensor devices. |
| 895 |
# These apply to the first 6 voltage inputs in0-in5 |
| 896 |
# (+2.5, Vccp1, +3.3, +5, 12, +Vccp2). As the scaling is fixed inside |
| 897 |
# the chip for these inputs, it is fairly certain that the |
| 898 |
# motherboard connections match these labels, and that the |
| 899 |
# driver computations are correct. Therefore they do not need to |
| 900 |
# be overridden here. |
| 901 |
|
| 902 |
label in0 "+2.5V" |
| 903 |
label in1 "VCore" |
| 904 |
label in2 "+3.3V" |
| 905 |
label in3 "+5V" |
| 906 |
label in4 "+12V" |
| 907 |
# label in5 "VCore2" |
| 908 |
|
| 909 |
label fan1 "CPU Fan" |
| 910 |
# label fan2 "Case Fan" |
| 911 |
label temp1 "M/B Temp" |
| 912 |
label temp2 "CPU Temp" |
| 913 |
# label temp3 "AUX Temp" |
| 914 |
|
| 915 |
# set in1_min cpu0_vid * 0.95 |
| 916 |
# set in1_max cpu0_vid * 1.05 |
| 917 |
# set in2_min 3.3 * 0.92 |
| 918 |
# set in2_max 3.3 * 1.08 |
| 919 |
# set in3_min 5 * 0.92 |
| 920 |
# set in3_max 5 * 1.08 |
| 921 |
# set in4_min 12 * 0.90 |
| 922 |
# set in4_max 12 * 1.10 |
| 923 |
|
| 924 |
# These ones are mutually exclusive with temp3. If you have temp3, |
| 925 |
# comment out these lines as they will trigger errors on "sensors -s". |
| 926 |
# set in0_min 2.5 * 0.92 |
| 927 |
# set in0_max 2.5 * 1.08 |
| 928 |
# set in5_min cpu0_vid * 0.95 |
| 929 |
# set in5_max cpu0_vid * 1.05 |
| 930 |
|
| 931 |
# Increase fan clock dividers if your fans read 0 RPM while you know |
| 932 |
# they are connected and running. |
| 933 |
# set fan1_div 4 |
| 934 |
# set fan2_div 4 |
| 935 |
|
| 936 |
# set fan1_min 3000 |
| 937 |
# set fan2_min 3000 |
| 938 |
|
| 939 |
# set temp1_min 5 |
| 940 |
# set temp1_max 65 |
| 941 |
# set temp2_min 5 |
| 942 |
# set temp2_max 70 |
| 943 |
|
| 944 |
# Uncomment if you actually have temp3 (which means you don't have 2.5V |
| 945 |
# nor Vccp2, as they are mutually exclusive). |
| 946 |
# set temp3_min 5 |
| 947 |
# set temp3_max 70 |
| 948 |
|
| 949 |
# LM87 AIN1 and AIN2 Section |
| 950 |
# -12 and -5 may be reversed on your board, this is |
| 951 |
# just a guess, the datasheet gives no guidance. |
| 952 |
# label in6 "-12V" |
| 953 |
# label in7 "-5V" |
| 954 |
# compute in6 (7.50 * @) - 21.45 , (@ + 21.45) / 7.50 |
| 955 |
# compute in7 (4.05 * @) - 10.07 , (@ + 10.07) / 4.05 |
| 956 |
# set in6_min -12 * 0.95 |
| 957 |
# set in7_min -5 * 0.95 |
| 958 |
# set in6_max -12 * 1.05 |
| 959 |
# set in7_max -5 * 1.05 |
| 960 |
|
| 961 |
|
| 962 |
chip "it87-*" "it8712-*" |
| 963 |
|
| 964 |
# The values below have been tested on Asus CUSI, CUM motherboards. |
| 965 |
|
| 966 |
# Voltage monitors as advised in the It8705 data sheet |
| 967 |
|
| 968 |
label in0 "VCore 1" |
| 969 |
label in1 "VCore 2" |
| 970 |
label in2 "+3.3V" |
| 971 |
label in3 "+5V" |
| 972 |
label in4 "+12V" |
| 973 |
label in5 "-12V" |
| 974 |
label in6 "-5V" |
| 975 |
label in7 "Stdby" |
| 976 |
label in8 "VBat" |
| 977 |
|
| 978 |
# Incubus Saturnus reports that the IT87 chip on Asus A7V8X-X seems |
| 979 |
# to report the VCORE voltage approximately 0.05V higher than the board's |
| 980 |
# BIOS does. Although it doesn't make much sense physically, uncommenting |
| 981 |
# the next line should bring the readings in line with the BIOS' ones in |
| 982 |
# this case. |
| 983 |
# compute in0 -0.05+@ , @+0.05 |
| 984 |
|
| 985 |
# If 3.3V reads around 1.65V, uncomment the following line: |
| 986 |
# compute in2 2*@ , @/2 |
| 987 |
|
| 988 |
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 989 |
# A number of Gigabyte boards (GA-8IPE1000Pro, GA-8KNXP, GA-7N400-L) use |
| 990 |
# a different resistor combination for +5V: |
| 991 |
# compute in3 ((10/10)+1)*@ , @/((10/10)+1) |
| 992 |
|
| 993 |
compute in4 ((30/10) +1)*@ , @/((30/10) +1) |
| 994 |
# For this family of chips the negative voltage equation is different from |
| 995 |
# the lm78. The chip uses two external resistor for scaling but one is |
| 996 |
# tied to a positive reference voltage. See ITE8705/12 datasheet (SIS950 |
| 997 |
# data sheet is wrong) |
| 998 |
# Vs = (1 + Rin/Rf) * Vin - (Rin/Rf) * Vref. |
| 999 |
# Vref = 4.096 volts, Vin is voltage measured, Vs is actual voltage. |
| 1000 |
|
| 1001 |
# The next two are negative voltages (-12 and -5). |
| 1002 |
# The following formulas must be used. Unfortunately the datasheet |
| 1003 |
# does not give recommendations for Rin, Rf, but we can back into |
| 1004 |
# them based on a nominal +2V input to the chip, together with a 4.096V Vref. |
| 1005 |
# Formula: |
| 1006 |
# actual V = (Vmeasured * (1 + Rin/Rf)) - (Vref * (Rin/Rf)) |
| 1007 |
# For -12V input use Rin/Rf = 6.68 |
| 1008 |
# For -5V input use Rin/Rf = 3.33 |
| 1009 |
# Then you can convert the forumula to a standard form like: |
| 1010 |
compute in5 (7.67 * @) - 27.36 , (@ + 27.36) / 7.67 |
| 1011 |
compute in6 (4.33 * @) - 13.64 , (@ + 13.64) / 4.33 |
| 1012 |
# |
| 1013 |
# this much simpler version is reported to work for a |
| 1014 |
# Elite Group K7S5A board |
| 1015 |
# |
| 1016 |
# compute in5 -(36/10)*@, -@/(36/10) |
| 1017 |
# compute in6 -(56/10)*@, -@/(56/10) |
| 1018 |
# |
| 1019 |
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 1020 |
|
| 1021 |
# set in0_min 1.5 * 0.95 |
| 1022 |
# set in0_max 1.5 * 1.05 |
| 1023 |
# set in1_min 2.4 |
| 1024 |
# set in1_max 2.6 |
| 1025 |
# set in2_min 3.3 * 0.95 |
| 1026 |
# set in2_max 3.3 * 1.05 |
| 1027 |
# set in3_min 5.0 * 0.95 |
| 1028 |
# set in3_max 5.0 * 1.05 |
| 1029 |
# set in4_min 12 * 0.95 |
| 1030 |
# set in4_max 12 * 1.05 |
| 1031 |
# set in5_max -12 * 0.95 |
| 1032 |
# set in5_min -12 * 1.05 |
| 1033 |
# set in6_max -5 * 0.95 |
| 1034 |
# set in6_min -5 * 1.05 |
| 1035 |
# set in7_min 5 * 0.95 |
| 1036 |
# set in7_max 5 * 1.05 |
| 1037 |
#the chip does not support in8 min/max |
| 1038 |
|
| 1039 |
# Temperature |
| 1040 |
# |
| 1041 |
# Important - if your temperature readings are completely whacky |
| 1042 |
# you probably need to change the sensor type. |
| 1043 |
# Adujst and uncomment the appropriate lines below. |
| 1044 |
# |
| 1045 |
# 2 = thermistor; 3 = thermal diode; 0 = unused |
| 1046 |
# set temp1_type 3 |
| 1047 |
# set temp2_type 3 |
| 1048 |
# set temp3_type 3 |
| 1049 |
# If a given sensor isn't used, you will probably want to ignore it |
| 1050 |
# (see ignore statement right below). |
| 1051 |
|
| 1052 |
label temp1 "M/B Temp" |
| 1053 |
# set temp1_max 40 |
| 1054 |
# set temp1_min 15 |
| 1055 |
label temp2 "CPU Temp" |
| 1056 |
# set temp2_max 45 |
| 1057 |
# set temp2_min 15 |
| 1058 |
# ignore temp3 |
| 1059 |
# set temp3_max 45 |
| 1060 |
# set temp3_min 15 |
| 1061 |
|
| 1062 |
# The A7V8X-X has temperatures inverted, and needs a conversion for |
| 1063 |
# CPU temp. Thanks to Preben Randhol for the formula. |
| 1064 |
# label temp1 "CPU Temp" |
| 1065 |
# label temp2 "M/B Temp" |
| 1066 |
# compute temp1 (-15.096+1.4893*@), (@+15.096)/1.4893 |
| 1067 |
|
| 1068 |
# The A7V600 also has temperatures inverted, and needs a different |
| 1069 |
# conversion for CPU temp. Thanks to Dariusz Jaszkowski for the formula. |
| 1070 |
# label temp1 "CPU Temp" |
| 1071 |
# label temp2 "M/B Temp" |
| 1072 |
# compute temp1 (@+128)/3, (3*@-128) |
| 1073 |
|
| 1074 |
# Fans |
| 1075 |
# set fan1_min 0 |
| 1076 |
# set fan2_min 3000 |
| 1077 |
# ignore fan3 |
| 1078 |
# set fan3_min 3000 |
| 1079 |
|
| 1080 |
|
| 1081 |
chip "it8716-*" |
| 1082 |
|
| 1083 |
# Voltages |
| 1084 |
|
| 1085 |
label in0 "VCore" |
| 1086 |
label in1 "VDDR" |
| 1087 |
label in2 "+3.3V" # VCC3 |
| 1088 |
label in3 "+5V" # VCC |
| 1089 |
label in4 "+12V" |
| 1090 |
# label in5 "-12V" |
| 1091 |
# label in6 "-5V" |
| 1092 |
label in7 "5VSB" # VCCH |
| 1093 |
label in8 "VBat" |
| 1094 |
|
| 1095 |
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 1096 |
compute in4 ((30/10)+1)*@ , @/((30/10)+1) |
| 1097 |
# compute in5 (1+232/56)*@ - 4.096*232/56 , (@ + 4.096*232/56)/(1+232/56) |
| 1098 |
# compute in6 (1+120/56)*@ - 4.096*120/56 , (@ + 4.096*120/56)/(1+120/56) |
| 1099 |
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1) |
| 1100 |
|
| 1101 |
# If vid (nominal CPU voltage) isn't correct, hardcode the correct value |
| 1102 |
# instead. |
| 1103 |
# set in0_min cpu0_vid * 0.95 |
| 1104 |
# set in0_max cpu0_vid * 1.05 |
| 1105 |
# set in1_min 1.8 * 0.95 |
| 1106 |
# set in1_max 1.8 * 1.05 |
| 1107 |
# set in2_min 3.3 * 0.95 |
| 1108 |
# set in2_max 3.3 * 1.05 |
| 1109 |
# set in3_min 5 * 0.95 |
| 1110 |
# set in3_max 5 * 1.05 |
| 1111 |
# set in4_min 12 * 0.95 |
| 1112 |
# set in4_max 12 * 1.05 |
| 1113 |
# set in5_max -12 * 0.95 |
| 1114 |
# set in5_min -12 * 1.05 |
| 1115 |
# set in6_max -5 * 0.95 |
| 1116 |
# set in6_min -5 * 1.05 |
| 1117 |
# set in7_min 5 * 0.95 |
| 1118 |
# set in7_max 5 * 1.05 |
| 1119 |
# The chip does not support in8 min/max |
| 1120 |
|
| 1121 |
# Temperatures |
| 1122 |
|
| 1123 |
# If you are lucky, the BIOS has set the proper sensor types for you. |
| 1124 |
# If your temperature readings are completely whacky you probably |
| 1125 |
# need to change the sensor types. Adujst and uncomment the |
| 1126 |
# appropriate lines below. |
| 1127 |
# |
| 1128 |
# 2 = thermistor; 3 = thermal diode; 0 = unused |
| 1129 |
# set temp1_type 3 |
| 1130 |
# set temp2_type 3 |
| 1131 |
# set temp3_type 3 |
| 1132 |
|
| 1133 |
# If a given sensor isn't used, you will probably want to ignore it |
| 1134 |
# as well (see ignore statement right below). |
| 1135 |
# The CPU sensor can be any of temp1, temp2 or temp3 - it's motherboard |
| 1136 |
# dependent. Same for the motherboard temperature. |
| 1137 |
|
| 1138 |
# label temp1 "CPU Temp" |
| 1139 |
# label temp2 "M/B Temp" |
| 1140 |
# ignore temp3 |
| 1141 |
|
| 1142 |
# set temp1_max 60 |
| 1143 |
# set temp1_min 10 |
| 1144 |
# set temp2_max 50 |
| 1145 |
# set temp2_min 10 |
| 1146 |
|
| 1147 |
# Fans |
| 1148 |
|
| 1149 |
# The CPU fan can be any of fan1, fan2 or fan3 - it's motherboard |
| 1150 |
# dependent. Same for the case fan. |
| 1151 |
|
| 1152 |
# label fan1 "CPU Fan" |
| 1153 |
# label fan2 "Case Fan" |
| 1154 |
# ignore fan3 |
| 1155 |
|
| 1156 |
# set fan1_min 2000 |
| 1157 |
# set fan2_min 2000 |
| 1158 |
|
| 1159 |
|
| 1160 |
chip "fscpos-*" |
| 1161 |
# Fujitsu-Siemens Poseidon chip |
| 1162 |
|
| 1163 |
# Temperature |
| 1164 |
|
| 1165 |
label temp1 "CPU Temp" |
| 1166 |
label temp2 "M/B Temp" |
| 1167 |
label temp3 "Aux Temp" |
| 1168 |
|
| 1169 |
# Fans |
| 1170 |
|
| 1171 |
# Voltage |
| 1172 |
|
| 1173 |
label in0 "+12V" |
| 1174 |
label in1 "+5V" |
| 1175 |
label in2 "Battery" |
| 1176 |
|
| 1177 |
|
| 1178 |
chip "fscscy-*" |
| 1179 |
# Fujitsu-Siemens Scylla chip |
| 1180 |
|
| 1181 |
# Temperature |
| 1182 |
|
| 1183 |
label temp1 "CPU0 Temp" |
| 1184 |
label temp2 "CPU1 Temp" |
| 1185 |
label temp3 "M/B Temp" |
| 1186 |
label temp4 "Aux Temp" |
| 1187 |
|
| 1188 |
# Fans |
| 1189 |
|
| 1190 |
label fan1 "CPU Fan" |
| 1191 |
label fan2 "CPU Fan" |
| 1192 |
|
| 1193 |
# Voltage |
| 1194 |
|
| 1195 |
label in0 "+12V" |
| 1196 |
label in1 "+5V" |
| 1197 |
label in2 "+3.3V" |
| 1198 |
|
| 1199 |
|
| 1200 |
chip "fscher-*" |
| 1201 |
# Fujitsu-Siemens Hermes chip |
| 1202 |
|
| 1203 |
# Temperature |
| 1204 |
label temp1 "CPU Temp" |
| 1205 |
label temp2 "M/B Temp" |
| 1206 |
label temp3 "Aux Temp" |
| 1207 |
|
| 1208 |
# Fans |
| 1209 |
label fan1 "PSU Fan" |
| 1210 |
label fan2 "CPU Fan" |
| 1211 |
label fan3 "Aux Fan" |
| 1212 |
|
| 1213 |
# Voltage |
| 1214 |
label in0 "+12V" |
| 1215 |
label in1 "+5V" |
| 1216 |
label in2 "Battery" |
| 1217 |
|
| 1218 |
# Uncomment the computes line below when using the old fscher driver, leave |
| 1219 |
# them commented when using the newer unified fschmd driver |
| 1220 |
# |
| 1221 |
# M R O O M R |
| 1222 |
# compute in0 (@ * (49 * 33) / 255) + (0 / 100), (@ - (0 / 100)) * 255 / (49 * 33) |
| 1223 |
# compute in1 (@ * (20 * 33) / 255) + (0 / 100), (@ - (0 / 100)) * 255 / (20 * 33) |
| 1224 |
# compute in2 (@ * (10 * 33) / 255) + (0 / 100), (@ - (0 / 100)) * 255 / (10 * 33) |
| 1225 |
|
| 1226 |
|
| 1227 |
chip "pcf8591-*" |
| 1228 |
# |
| 1229 |
# values for the Philips PCF8591 chip |
| 1230 |
# |
| 1231 |
# Analog inputs |
| 1232 |
|
| 1233 |
# You may discard ch2 and ch3 if you don't use them (depends on the input |
| 1234 |
# configuration) |
| 1235 |
# ignore in2 |
| 1236 |
# ignore in3 |
| 1237 |
|
| 1238 |
label in0 "Chan. 0" |
| 1239 |
label in1 "Chan. 1" |
| 1240 |
label in2 "Chan. 2" |
| 1241 |
label in3 "Chan. 3" |
| 1242 |
|
| 1243 |
# The driver assumes Vref = 2.56V and Agnd = 0V. If it doesn't match |
| 1244 |
# your hardware, you have to use compute lines. The example below is |
| 1245 |
# correct for Vref = 5.0V and Agnd = 0V. |
| 1246 |
# compute in0 (@ * 500 / 256), (@ * 256 / 500) |
| 1247 |
# compute in1 (@ * 500 / 256), (@ * 256 / 500) |
| 1248 |
# compute in2 (@ * 500 / 256), (@ * 256 / 500) |
| 1249 |
# compute in3 (@ * 500 / 256), (@ * 256 / 500) |
| 1250 |
|
| 1251 |
|
| 1252 |
chip "adm1021-*" "adm1023-*" "max1617-*" "max1617a-*" "thmc10-*" "lm84-*" "gl523sm-*" "mc1066-*" |
| 1253 |
|
| 1254 |
label temp1 "Board Temp" |
| 1255 |
label temp2 "CPU Temp" |
| 1256 |
# set temp1_min 40 |
| 1257 |
# set temp1_max 70 |
| 1258 |
# set temp2_min 40 |
| 1259 |
# set temp2_max 70 |
| 1260 |
|
| 1261 |
chip "lm83-*" |
| 1262 |
|
| 1263 |
label temp1 "M/B Temp" |
| 1264 |
label temp2 "D1 Temp" |
| 1265 |
label temp3 "CPU Temp" |
| 1266 |
label temp4 "D3 Temp" |
| 1267 |
|
| 1268 |
# ignore D1 and/or D3 readings if not used |
| 1269 |
# ignore temp2 |
| 1270 |
# ignore temp4 |
| 1271 |
|
| 1272 |
# change high limits to fit your needs |
| 1273 |
# set temp1_max 55 |
| 1274 |
# set temp2_max 60 |
| 1275 |
# set temp3_max 65 |
| 1276 |
# set temp4_max 60 |
| 1277 |
|
| 1278 |
# change critical limit to fit your needs |
| 1279 |
# only one limit for all four temperatures |
| 1280 |
# should be higher than each of the high limits above |
| 1281 |
# set temp3_crit 85 |
| 1282 |
|
| 1283 |
|
| 1284 |
chip "max1619-*" |
| 1285 |
|
| 1286 |
label temp1 "M/B Temp" |
| 1287 |
label temp2 "CPU Temp" |
| 1288 |
|
| 1289 |
# change high and low limits to fit your needs |
| 1290 |
# set temp2_min 10 |
| 1291 |
# set temp2_max 100 |
| 1292 |
|
| 1293 |
# change critical limit and hysteresis to fit your needs |
| 1294 |
# set temp2_crit 50 |
| 1295 |
# set temp2_crit_hyst 40 |
| 1296 |
|
| 1297 |
|
| 1298 |
chip "lm90-*" "adm1032-*" "lm86-*" "max6657-*" "adt7461-*" "max6680-*" "w83l771-*" |
| 1299 |
|
| 1300 |
label temp1 "M/B Temp" |
| 1301 |
label temp2 "CPU Temp" |
| 1302 |
|
| 1303 |
# change high and low limits to fit your needs |
| 1304 |
# set temp1_min 10 |
| 1305 |
# set temp1_max 55 |
| 1306 |
# set temp2_min 10 |
| 1307 |
# set temp2_max 66 |
| 1308 |
|
| 1309 |
# change critical limits to fit your needs |
| 1310 |
# should be higher than the corresponding high limit above |
| 1311 |
# set temp1_crit 75 |
| 1312 |
# set temp2_crit 85 |
| 1313 |
|
| 1314 |
# change the hysteresis values (to critical limits) to fit your needs |
| 1315 |
# note #1: hyst2 will be automatically set with the same delta |
| 1316 |
# note #2: the internal register, which stores a single, relative value |
| 1317 |
# for both channels, cannot hold values greater than 31, so the delta |
| 1318 |
# between critical temperatures and respective absolute hysteresis can |
| 1319 |
# never exceed this value |
| 1320 |
# set temp1_crit_hyst 70 |
| 1321 |
|
| 1322 |
chip "lm89-*" "lm99-*" |
| 1323 |
|
| 1324 |
label temp1 "G/C Temp" |
| 1325 |
label temp2 "GPU Temp" |
| 1326 |
|
| 1327 |
# note #1: the LM99 needs the compute statement below if you're running |
| 1328 |
# a kernel <= 2.6.27; since kernel 2.6.28 the offset is handled in the |
| 1329 |
# lm90 driver directly instead |
| 1330 |
# note #2: there is no way for us to differentiate between a LM89 and a |
| 1331 |
# LM99; you have to know what you have; the driver will assume a LM99, |
| 1332 |
# use the force_lm86 module parameter if you have a LM89 |
| 1333 |
# compute temp2 @+16, @-16 |
| 1334 |
|
| 1335 |
# change high and low limits to fit your needs |
| 1336 |
# set temp1_min 10 |
| 1337 |
# set temp1_max 90 |
| 1338 |
# set temp2_min 10 |
| 1339 |
# set temp2_max 100 |
| 1340 |
|
| 1341 |
# change critical limits to fit your needs |
| 1342 |
# should be higher than the corresponding high limit above |
| 1343 |
# set temp1_crit 100 |
| 1344 |
# set temp2_crit 110 |
| 1345 |
|
| 1346 |
# change the hysteresis values (to critical limits) to fit your needs |
| 1347 |
# note #1: hyst2 will be automatically set with the same delta |
| 1348 |
# note #2: the internal register, which stores a single, relative value |
| 1349 |
# for both channels, cannot hold values greater than 31, so the delta |
| 1350 |
# between critical temperatures and respective absolute hysteresis can |
| 1351 |
# never exceed this value |
| 1352 |
# set temp1_crit_hyst 105 |
| 1353 |
|
| 1354 |
|
| 1355 |
chip "lm63-*" |
| 1356 |
|
| 1357 |
label temp1 "M/B Temp" |
| 1358 |
label temp2 "CPU Temp" |
| 1359 |
label fan1 "CPU Fan" |
| 1360 |
|
| 1361 |
# Change limits to fit your needs. Note that temp2_crit is read-only. |
| 1362 |
# set temp1_max 50 |
| 1363 |
# set temp2_min 10 |
| 1364 |
# set temp2_max 70 |
| 1365 |
# set temp2_crit_hyst 75 |
| 1366 |
# set fan1_min 2000 |
| 1367 |
|
| 1368 |
|
| 1369 |
chip "vt1211-*" |
| 1370 |
|
| 1371 |
label in0 "+3.3V" |
| 1372 |
label in1 "+2.5V" |
| 1373 |
label in2 "VCore" |
| 1374 |
label in3 "+5V" |
| 1375 |
label in4 "+12V" |
| 1376 |
label in5 "+3.3V" |
| 1377 |
|
| 1378 |
label temp1 "CPU Temp" |
| 1379 |
label temp2 "Int Temp" |
| 1380 |
|
| 1381 |
label fan1 "Case Fan" |
| 1382 |
label fan2 "CPU Fan" |
| 1383 |
|
| 1384 |
# All voltage calculations have the form |
| 1385 |
# compute inX @ * (1 + R1 / R2), @ / (1 + R1 / R2) |
| 1386 |
# |
| 1387 |
# The following are the resistor values as recommended by VIA |
| 1388 |
# Voltage R1 R2 |
| 1389 |
# ------- ---- ---- |
| 1390 |
# VCore - - (no scaling) |
| 1391 |
# 3.3 6.8k 10k |
| 1392 |
# 2.5 2k 10k |
| 1393 |
# 5.0 14k 10k |
| 1394 |
# 12.0 47k 10k |
| 1395 |
# |
| 1396 |
# The VT1211 internal 3.3V (in5) is scaled by the driver and doesn't |
| 1397 |
# need to be adjusted here. VCore doesn't need scaling at all. |
| 1398 |
|
| 1399 |
compute in0 @ * (1 + 6.8 / 10), @ / (1 + 6.8 / 10) |
| 1400 |
compute in1 @ * (1 + 2 / 10), @ / (1 + 2 / 10) |
| 1401 |
compute in3 @ * (1 + 14 / 10), @ / (1 + 14 / 10) |
| 1402 |
compute in4 @ * (1 + 47 / 10), @ / (1 + 47 / 10) |
| 1403 |
|
| 1404 |
# set in0_min 3.3 * 0.95 |
| 1405 |
# set in0_max 3.3 * 1.05 |
| 1406 |
# set in1_min 2.5 * 0.95 |
| 1407 |
# set in1_max 2.5 * 1.05 |
| 1408 |
# If your vid is wrong, hardcode the CPU voltage (e.g. 1.4) |
| 1409 |
# set in2_min cpu0_vid * 0.97 |
| 1410 |
# set in2_max cpu0_vid * 1.03 |
| 1411 |
# set in3_min 5.0 * 0.95 |
| 1412 |
# set in3_max 5.0 * 1.05 |
| 1413 |
# set in4_min 12.0 * 0.90 |
| 1414 |
# set in4_max 12.0 * 1.10 |
| 1415 |
set in5_min 3.3 * 0.95 |
| 1416 |
set in5_max 3.3 * 1.05 |
| 1417 |
|
| 1418 |
# The temperature calculations are of the form |
| 1419 |
# compute tempX (@ - Offset) / Gain, (@ * Gain) + Offset |
| 1420 |
# |
| 1421 |
# The following are the gain and offset values as recommended by VIA |
| 1422 |
# Diode Type Gain Offset |
| 1423 |
# ---------- ---- ------ |
| 1424 |
# Intel CPU 0.9528 88.638 |
| 1425 |
# 0.9686 65.000 *) |
| 1426 |
# VIA C3 Ezra 0.9528 83.869 |
| 1427 |
# VIA C3 Ezra-T 0.9528 73.869 |
| 1428 |
# |
| 1429 |
# *) These are the values from the previous sensors.conf. I don't know |
| 1430 |
# where they came from or how they got derived. |
| 1431 |
# |
| 1432 |
# The VT1211 internal temperature (temp2) is scaled by the driver |
| 1433 |
# and doesn't need to be adjusted here. |
| 1434 |
|
| 1435 |
compute temp1 (@ - 73.869) / 0.9528, (@ * 0.9528) + 73.869 |
| 1436 |
|
| 1437 |
# The thermistor calculations are of the form |
| 1438 |
# compute tempX 1 / (1 / 298.15 - (` Vmax / @ - 1)) / B) - 273.15, \ |
| 1439 |
# Vmax / (1 + (^ (B / 298.15 - B / (273.15 + @)))) |
| 1440 |
# |
| 1441 |
# B is the thermistor beta value, Vmax is the reference voltage, '^' is the |
| 1442 |
# exp() operator and '`' is the ln() operator. |
| 1443 |
# Given B = 3435 and Vmax = 2.2V and assuming that the thermistor forms a |
| 1444 |
# resistor divider with a resistor equal to the thermistor's nominal value at |
| 1445 |
# 25 degrees C, the following compute lines can be used: |
| 1446 |
|
| 1447 |
compute temp3 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \ |
| 1448 |
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @)))) |
| 1449 |
compute temp4 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \ |
| 1450 |
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @)))) |
| 1451 |
compute temp5 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \ |
| 1452 |
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @)))) |
| 1453 |
compute temp6 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \ |
| 1454 |
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @)))) |
| 1455 |
compute temp7 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \ |
| 1456 |
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @)))) |
| 1457 |
|
| 1458 |
# set temp1_max 85 |
| 1459 |
# set temp1_max_hyst 80 |
| 1460 |
# set temp2_max 65 |
| 1461 |
# set temp2_max_hyst 60 |
| 1462 |
# set temp3_max 65 |
| 1463 |
# set temp3_max_hyst 60 |
| 1464 |
# set temp4_max 45 |
| 1465 |
# set temp4_max_hyst 40 |
| 1466 |
|
| 1467 |
# set fan1_min 3000 |
| 1468 |
# set fan2_min 3000 |
| 1469 |
|
| 1470 |
chip "vt8231-*" |
| 1471 |
|
| 1472 |
label in1 "+2.5V" |
| 1473 |
label in2 "VCore" |
| 1474 |
label in3 "+5V" |
| 1475 |
label in4 "+12V" |
| 1476 |
label in5 "+3.3V" |
| 1477 |
|
| 1478 |
label temp1 "CPU Temp" |
| 1479 |
label temp2 "M/B Temp" |
| 1480 |
|
| 1481 |
# Here are the resistor values as recommended by VIA: |
| 1482 |
# Voltage R1 R2 |
| 1483 |
# VCore no scaling |
| 1484 |
# 2.5 2k 10k |
| 1485 |
# 3.5 (3.3V ext.) 6.8k 10k |
| 1486 |
# 5.0 14k 10k |
| 1487 |
# 12.0 47k 10k |
| 1488 |
|
| 1489 |
# compute in0 @ * (1 + 6.8 / 10), @ / (1 + 6.8 / 10) |
| 1490 |
compute in1 @ * (1 + 2 / 10), @ / (1 + 2 / 10) |
| 1491 |
compute in3 @ * (1 + 14 / 10), @ / (1 + 14 / 10) |
| 1492 |
compute in4 @ * (1 + 47 / 10), @ / (1 + 47 / 10) |
| 1493 |
# in5 is scaled internally so scaling is done by the driver. |
| 1494 |
|
| 1495 |
# set in0_min 2.5 * 0.95 |
| 1496 |
# set in0_max 2.5 * 1.05 |
| 1497 |
# set in1_min 2.5 * 0.95 |
| 1498 |
# set in1_max 2.5 * 1.05 |
| 1499 |
# Replace "2.0" with your nominal CPU voltage for in2. |
| 1500 |
# set in2_min 2.0 * 0.95 |
| 1501 |
# set in2_max 2.0 * 1.05 |
| 1502 |
# set in3_min 5.0 * 0.95 |
| 1503 |
# set in3_max 5.0 * 1.05 |
| 1504 |
# set in4_min 12.0 * 0.95 |
| 1505 |
# set in4_max 12.0 * 1.05 |
| 1506 |
# set in5_min 3.3 * 0.95 |
| 1507 |
# set in5_max 3.3 * 1.05 |
| 1508 |
|
| 1509 |
# For Intel CPU: |
| 1510 |
compute temp1 (@ - 65) / 0.9686, (@ * 0.9686) + 65 |
| 1511 |
|
| 1512 |
# For VIA EPIA CPU (provided by Roger Lucas): |
| 1513 |
# compute temp1 (@ - 45) / 0.7809, (@ * 0.7809) + 45 |
| 1514 |
|
| 1515 |
# Thermistor calculations |
| 1516 |
# 3435 is the thermistor beta, 2.2 is the reference voltage. |
| 1517 |
# '^' is the e**x operator; '`' is the ln(x) operator |
| 1518 |
# This assumes that the thermistor forms a resistor divider with a resistor |
| 1519 |
# equal to its nominal value at 25 degrees C. |
| 1520 |
|
| 1521 |
compute temp2 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \ |
| 1522 |
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @)))) |
| 1523 |
compute temp3 1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \ |
| 1524 |
2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @)))) |
| 1525 |
|
| 1526 |
# set temp1_max 65 |
| 1527 |
# set temp1_max_hyst 60 |
| 1528 |
# set temp2_max 45 |
| 1529 |
# set temp2_max_hyst 40 |
| 1530 |
|
| 1531 |
# set fan1_min 3000 |
| 1532 |
# set fan2_min 3000 |
| 1533 |
|
| 1534 |
|
| 1535 |
chip "smsc47m1-*" |
| 1536 |
|
| 1537 |
# SMSC LPC47M10x, LPC47M13x, LPC47M14x and LPC47B27x chips |
| 1538 |
|
| 1539 |
# set fan1_min 3000 |
| 1540 |
# set fan2_min 3000 |
| 1541 |
|
| 1542 |
chip "smsc47m192-*" |
| 1543 |
|
| 1544 |
# Temperature and voltage input from SMSC LPC47M192 and LPC47M997 chips |
| 1545 |
# This example works on a Gigabyte K8U motherboard |
| 1546 |
# Voltages are scaled internally, no computations needed |
| 1547 |
|
| 1548 |
label in0 "+2.5V" |
| 1549 |
# set in0_min 2.5 * 0.95 |
| 1550 |
# set in0_max 2.5 * 1.05 |
| 1551 |
|
| 1552 |
label in1 "VCore" |
| 1553 |
# set in1_min cpu0_vid * 0.95 |
| 1554 |
# set in1_max cpu0_vid * 1.05 |
| 1555 |
|
| 1556 |
label in2 "+3.3V" |
| 1557 |
# set in2_min 3.3 * 0.95 |
| 1558 |
# set in2_max 3.3 * 1.05 |
| 1559 |
|
| 1560 |
label in3 "+5V" |
| 1561 |
# set in3_min 5.0 * 0.95 |
| 1562 |
# set in3_max 5.0 * 1.05 |
| 1563 |
|
| 1564 |
label in4 "+12V" |
| 1565 |
# set in4_min 12.0 * 0.95 |
| 1566 |
# set in4_max 12.0 * 1.05 |
| 1567 |
|
| 1568 |
label in5 "VCC" |
| 1569 |
# set in5_min 3.3 * 0.95 |
| 1570 |
# set in5_max 3.3 * 1.05 |
| 1571 |
|
| 1572 |
label in6 "+1.5V" |
| 1573 |
# set in6_min 1.5 * 0.95 |
| 1574 |
# set in6_max 1.5 * 1.05 |
| 1575 |
# ignore in6 |
| 1576 |
|
| 1577 |
label in7 "+1.8V" |
| 1578 |
# set in7_min 1.8 * 0.95 |
| 1579 |
# set in7_max 1.8 * 1.05 |
| 1580 |
# Haven't yet heard from any board that has 1.8V connected, so |
| 1581 |
# this might be more appropriate: |
| 1582 |
# ignore in7 |
| 1583 |
|
| 1584 |
label temp1 "Chip Temp" |
| 1585 |
# set temp1_min 0 |
| 1586 |
# set temp1_max 60 |
| 1587 |
|
| 1588 |
label temp2 "CPU Temp" |
| 1589 |
# set temp2_min 0 |
| 1590 |
# set temp2_max 60 |
| 1591 |
|
| 1592 |
label temp3 "Sys Temp" |
| 1593 |
# set temp3_min 0 |
| 1594 |
# set temp3_max 60 |
| 1595 |
|
| 1596 |
# |
| 1597 |
# This example was tested vs. Asus P4S333 |
| 1598 |
# |
| 1599 |
chip "asb100-*" |
| 1600 |
|
| 1601 |
label in0 "VCore 1" |
| 1602 |
#set in0_min cpu0_vid * 0.95 |
| 1603 |
#set in0_max cpu0_vid * 1.05 |
| 1604 |
|
| 1605 |
label in1 "VCore 2" |
| 1606 |
ignore in1 |
| 1607 |
#set in1_min cpu0_vid * 0.95 |
| 1608 |
#set in1_max cpu0_vid * 1.05 |
| 1609 |
|
| 1610 |
label in2 "+3.3V" |
| 1611 |
#set in2_min 3.3 * 0.95 |
| 1612 |
#set in2_max 3.3 * 1.05 |
| 1613 |
|
| 1614 |
label in3 "+5V" |
| 1615 |
compute in3 1.68 * @ , @ / 1.68 |
| 1616 |
#set in3_min 5.0 * 0.95 |
| 1617 |
#set in3_max 5.0 * 1.05 |
| 1618 |
|
| 1619 |
label in4 "+12V" |
| 1620 |
compute in4 3.8 * @ , @ / 3.8 |
| 1621 |
#set in4_min 12 * 0.90 |
| 1622 |
#set in4_max 12 * 1.10 |
| 1623 |
|
| 1624 |
label in5 "-12V (reserved)" |
| 1625 |
#ignore in5 |
| 1626 |
compute in5 -@ * 3.97 , -@ / 3.97 |
| 1627 |
#set in5_max -12 * 0.90 |
| 1628 |
#set in5_min -12 * 1.10 |
| 1629 |
|
| 1630 |
label in6 "-5V (reserved)" |
| 1631 |
#ignore in6 |
| 1632 |
compute in6 -@ * 1.666 , -@ / 1.666 |
| 1633 |
#set in6_max -5 * 0.95 |
| 1634 |
#set in6_min -5 * 1.05 |
| 1635 |
|
| 1636 |
label temp1 "M/B Temp" |
| 1637 |
#set temp1_max 45 |
| 1638 |
#set temp1_max_hyst 40 |
| 1639 |
|
| 1640 |
label temp2 "CPU Temp (Intel)" |
| 1641 |
#ignore temp2 |
| 1642 |
#set temp2_max 60 |
| 1643 |
#set temp2_max_hyst 50 |
| 1644 |
|
| 1645 |
# PWRTMP connector on P4S333, for external sensor |
| 1646 |
label temp3 "Power Temp" |
| 1647 |
#ignore temp3 |
| 1648 |
#set temp3_max 45 |
| 1649 |
#set temp3_max_hyst 40 |
| 1650 |
|
| 1651 |
|
| 1652 |
# Used for Athlon diode, ignore for P4S333 |
| 1653 |
label temp4 "CPU Temp (AMD)" |
| 1654 |
#set temp4_max 60 |
| 1655 |
#set temp4_max_hyst 50 |
| 1656 |
#ignore temp4 |
| 1657 |
|
| 1658 |
label fan1 "CPU Fan" |
| 1659 |
#set fan1_div 4 |
| 1660 |
#set fan1_min 2000 |
| 1661 |
|
| 1662 |
label fan2 "Chassis Fan" |
| 1663 |
#set fan2_div 2 |
| 1664 |
#set fan2_min 4000 |
| 1665 |
|
| 1666 |
label fan3 "Power Fan" |
| 1667 |
#set fan3_div 2 |
| 1668 |
#set fan3_min 4000 |
| 1669 |
|
| 1670 |
# |
| 1671 |
# Sample configuration for the Intel S845WD1-E |
| 1672 |
# courtesy of Marcus Schopen |
| 1673 |
# |
| 1674 |
chip "lm85-*" "lm85b-*" "lm85c-*" "adm1027-*" "adt7463-*" "adt7468-*" "emc6d100-*" "emc6d102-*" |
| 1675 |
|
| 1676 |
# Voltage inputs |
| 1677 |
# Depending on the hardware setup, the ADT7463 and ADT7468 may not have in4. |
| 1678 |
label in0 "V1.5" # AGP on Intel S845WD1-E |
| 1679 |
label in1 "VCore" |
| 1680 |
label in2 "V3.3" |
| 1681 |
label in3 "V5" |
| 1682 |
label in4 "V12" |
| 1683 |
|
| 1684 |
# Temperature inputs |
| 1685 |
label temp1 "CPU Temp" |
| 1686 |
label temp2 "Board Temp" |
| 1687 |
label temp3 "Remote Temp" |
| 1688 |
|
| 1689 |
# Fan inputs |
| 1690 |
label fan1 "CPU Fan" |
| 1691 |
|
| 1692 |
# Voltage scaling is done on-chip. No 'compute' directive |
| 1693 |
# should be necessary. If in0 has external scaling set |
| 1694 |
# it here. |
| 1695 |
|
| 1696 |
# compute in0 @ * 2.5, @ / 2.5 |
| 1697 |
|
| 1698 |
# Adjust fans speeds for actual pulses per rev |
| 1699 |
# compute fan1 @ * 2, @ / 2 # 1 pulse per rev |
| 1700 |
# compute fan2 @ / 2, @ * 2 # 4 pulse per rev |
| 1701 |
|
| 1702 |
# Ignore fans you (or your motherboard) don't have |
| 1703 |
# ignore fan2 |
| 1704 |
# ignore fan3 |
| 1705 |
# ignore fan4 |
| 1706 |
|
| 1707 |
# Set voltage limits |
| 1708 |
# set in0_min 1.5 * 0.95 |
| 1709 |
# set in0_max 1.5 * 1.05 |
| 1710 |
# set in1_min cpu0_vid * 0.95 |
| 1711 |
# set in1_max cpu0_vid * 1.05 |
| 1712 |
# set in2_min 3.3 * 0.95 |
| 1713 |
# set in2_max 3.3 * 1.05 |
| 1714 |
# set in3_min 5.0 * 0.95 |
| 1715 |
# set in3_max 5.0 * 1.05 |
| 1716 |
# set in4_min 12 * 0.95 |
| 1717 |
# set in4_max 12 * 1.05 |
| 1718 |
|
| 1719 |
# Set Fan limits |
| 1720 |
# set fan1_min 4000 |
| 1721 |
|
| 1722 |
# Set Temp Limits |
| 1723 |
# set temp1_min 10 |
| 1724 |
# set temp1_max 50 |
| 1725 |
# set temp2_min 10 |
| 1726 |
# set temp2_max 35 |
| 1727 |
# set temp3_min 10 |
| 1728 |
# set temp3_max 35 |
| 1729 |
|
| 1730 |
chip "pc87365-*" "pc87366-*" |
| 1731 |
|
| 1732 |
# Voltage inputs |
| 1733 |
|
| 1734 |
label in7 "Vsb" |
| 1735 |
label in8 "Vdd" |
| 1736 |
label in9 "Vbat" |
| 1737 |
label in10 "AVdd" |
| 1738 |
|
| 1739 |
compute in7 @*2, @/2 |
| 1740 |
compute in8 @*2, @/2 |
| 1741 |
compute in10 @*2, @/2 |
| 1742 |
|
| 1743 |
# These are the operating conditions as recommended by National |
| 1744 |
# Semiconductor |
| 1745 |
set in7_min 3.0 |
| 1746 |
set in7_max 3.6 |
| 1747 |
set in8_min 3.0 |
| 1748 |
set in8_max 3.6 |
| 1749 |
# set in9_min 2.4 |
| 1750 |
# set in9_max 3.6 |
| 1751 |
set in10_min 3.0 |
| 1752 |
set in10_max 3.6 |
| 1753 |
|
| 1754 |
# Temperature inputs |
| 1755 |
|
| 1756 |
label temp1 "CPU0 Temp" |
| 1757 |
label temp2 "CPU1 Temp" |
| 1758 |
label temp3 "S-IO Temp" |
| 1759 |
|
| 1760 |
# set temp1_min 0 |
| 1761 |
# set temp1_max 70 |
| 1762 |
# set temp1_crit 85 |
| 1763 |
# set temp2_min 0 |
| 1764 |
# set temp2_max 70 |
| 1765 |
# set temp2_crit 85 |
| 1766 |
# set temp3_min 0 |
| 1767 |
# set temp3_max 70 |
| 1768 |
# set temp3_crit 85 |
| 1769 |
|
| 1770 |
# Thermistors |
| 1771 |
# On some systems, thermistors are used instead of thermal diodes. |
| 1772 |
# Note that these are the same pins used differently, so you really |
| 1773 |
# can't have them all on a given system. |
| 1774 |
# ignore temp1 |
| 1775 |
# ignore temp2 |
| 1776 |
ignore temp4 |
| 1777 |
ignore temp5 |
| 1778 |
ignore temp6 |
| 1779 |
|
| 1780 |
# 3435 is the thermistor beta. |
| 1781 |
# This assumes that the thermistor forms a resistor divider with a resistor |
| 1782 |
# equal to its nominal value at 25 degres Celsius. If not, change the values. |
| 1783 |
# We also assume that you have a working in10 (which is forcibly enabled by |
| 1784 |
# default). If not, use 3.3 instead, but you lose accuracy. |
| 1785 |
|
| 1786 |
compute temp4 3435 / (` (1 / (1 - @ / in10_input) - 1) + 3435 / 298.15) - 273.15, \ |
| 1787 |
in10_input * (1 - 1 / (1 + (^ (3435 / (273.15 + @) - 3435 / 298.15)))) |
| 1788 |
compute temp5 3435 / (` (1 / (1 - @ / in10_input) - 1) + 3435 / 298.15) - 273.15, \ |
| 1789 |
in10_input * (1 - 1 / (1 + (^ (3435 / (273.15 + @) - 3435 / 298.15)))) |
| 1790 |
compute temp6 3435 / (` (1 / (1 - @ / in10_input) - 1) + 3435 / 298.15) - 273.15, \ |
| 1791 |
in10_input * (1 - 1 / (1 + (^ (3435 / (273.15 + @) - 3435 / 298.15)))) |
| 1792 |
|
| 1793 |
# set temp4_min 0 |
| 1794 |
# set temp4_max 70 |
| 1795 |
# set temp4_crit 85 |
| 1796 |
# set temp5_min 0 |
| 1797 |
# set temp5_max 70 |
| 1798 |
# set temp5_crit 85 |
| 1799 |
# set temp6_min 0 |
| 1800 |
# set temp6_max 70 |
| 1801 |
# set temp6_crit 85 |
| 1802 |
|
| 1803 |
# Fan inputs |
| 1804 |
|
| 1805 |
# Ignore fans you don't have |
| 1806 |
# ignore fan2 |
| 1807 |
# ignore fan3 |
| 1808 |
|
| 1809 |
# set fan1_min 2000 |
| 1810 |
# set fan2_min 2000 |
| 1811 |
# set fan3_min 2000 |
| 1812 |
|
| 1813 |
|
| 1814 |
chip "adm1030-*" |
| 1815 |
|
| 1816 |
label temp1 "SYS Temp" |
| 1817 |
label temp2 "CPU Temp" |
| 1818 |
|
| 1819 |
# set temp1_max 60 |
| 1820 |
# set temp2_max 70 |
| 1821 |
# set temp1_crit 85 |
| 1822 |
# set temp2_crit 85 |
| 1823 |
|
| 1824 |
label fan1 "CPU Fan" |
| 1825 |
|
| 1826 |
# set fan1_min 2000 |
| 1827 |
|
| 1828 |
|
| 1829 |
chip "adm1031-*" |
| 1830 |
|
| 1831 |
label temp1 "SYS Temp" |
| 1832 |
label temp2 "CPU Temp" |
| 1833 |
label temp3 "AUX Temp" |
| 1834 |
|
| 1835 |
# set temp1_max 60 |
| 1836 |
# set temp2_max 70 |
| 1837 |
# set temp3_max 70 |
| 1838 |
# set temp1_crit 85 |
| 1839 |
# set temp2_crit 85 |
| 1840 |
# set temp3_crit 85 |
| 1841 |
|
| 1842 |
label fan1 "CPU Fan" |
| 1843 |
label fan2 "Case Fan" |
| 1844 |
|
| 1845 |
# set fan1_min 2000 |
| 1846 |
# set fan2_min 2000 |
| 1847 |
|
| 1848 |
|
| 1849 |
chip "w83l785ts-*" |
| 1850 |
|
| 1851 |
label temp1 "CPU Diode" |
| 1852 |
|
| 1853 |
chip "lm92-*" |
| 1854 |
|
| 1855 |
label temp1 "CPU Temp" |
| 1856 |
|
| 1857 |
# Change limits as you see fit |
| 1858 |
# set temp1_min 14 |
| 1859 |
# set temp1_max 60 |
| 1860 |
# set temp1_crit 72 |
| 1861 |
# Hysteresis is computed from critical limit |
| 1862 |
# The same relative hysteresis is used for all of low, high |
| 1863 |
# and critical limits. |
| 1864 |
# set temp1_crit_hyst 70 |
| 1865 |
|
| 1866 |
|
| 1867 |
# Winbond W83627EHF configuration originally contributed by Leon Moonen |
| 1868 |
# This is for an Asus P5P800, voltages for A8V-E SE. |
| 1869 |
chip "w83627ehf-*" "w83627dhg-*" |
| 1870 |
|
| 1871 |
label in0 "VCore" |
| 1872 |
label in1 "+12V" |
| 1873 |
label in2 "AVCC" |
| 1874 |
label in3 "3VCC" |
| 1875 |
label in6 "+5V" |
| 1876 |
label in7 "VSB" |
| 1877 |
label in8 "VBAT" |
| 1878 |
|
| 1879 |
# +12V is in1 and +5V is in6 as recommended by datasheet |
| 1880 |
compute in1 @*(1+(56/10)), @/(1+(56/10)) |
| 1881 |
compute in6 @*(1+(22/10)), @/(1+(22/10)) |
| 1882 |
# set in1_min 12.0*0.9 |
| 1883 |
# set in1_max 12.0*1.1 |
| 1884 |
# set in6_min 5.0*0.95 |
| 1885 |
# set in6_max 5.0*1.05 |
| 1886 |
|
| 1887 |
# Set the 3.3V |
| 1888 |
# set in2_min 3.3*0.95 |
| 1889 |
# set in2_max 3.3*1.05 |
| 1890 |
# set in3_min 3.3*0.95 |
| 1891 |
# set in3_max 3.3*1.05 |
| 1892 |
# set in7_min 3.3*0.95 |
| 1893 |
# set in7_max 3.3*1.05 |
| 1894 |
# set in8_min 3.3*0.95 |
| 1895 |
# set in8_max 3.3*1.05 |
| 1896 |
|
| 1897 |
# Fans |
| 1898 |
label fan1 "Case Fan" |
| 1899 |
label fan2 "CPU Fan" |
| 1900 |
label fan3 "Aux Fan" |
| 1901 |
# ignore fan3 |
| 1902 |
# ignore fan4 |
| 1903 |
# set fan1_min 1200 |
| 1904 |
# set fan2_min 1700 |
| 1905 |
|
| 1906 |
# Temperatures |
| 1907 |
label temp1 "Sys Temp" |
| 1908 |
label temp2 "CPU Temp" |
| 1909 |
label temp3 "AUX Temp" |
| 1910 |
|
| 1911 |
# ignore temp3 |
| 1912 |
# set temp1_max 45 |
| 1913 |
# set temp1_max_hyst 40 |
| 1914 |
# set temp2_max 45 |
| 1915 |
# set temp2_max_hyst 40 |
| 1916 |
|
| 1917 |
|
| 1918 |
# Fintek F71805F/FG configuration |
| 1919 |
# This is the recommended wiring and resistor values from the F71805F/FG |
| 1920 |
# datasheet. Your motherboard manufacturer may or may not have followed |
| 1921 |
# these. |
| 1922 |
chip "f71805f-*" "f71872f-*" |
| 1923 |
# Voltages |
| 1924 |
label in0 "+3.3V" |
| 1925 |
label in1 "Vtt1.2V" |
| 1926 |
label in2 "Vram" |
| 1927 |
label in3 "Vchip" |
| 1928 |
label in4 "+5V" |
| 1929 |
label in5 "+12V" |
| 1930 |
label in6 "Vcc1.5V" |
| 1931 |
label in7 "Vcore" |
| 1932 |
label in8 "5VSB" |
| 1933 |
|
| 1934 |
# in0 is scaled internally |
| 1935 |
compute in2 @*(1+100/100), @/(1+100/100) |
| 1936 |
compute in3 @*(1+100/47), @/(1+100/47) |
| 1937 |
compute in4 @*(1+200/47), @/(1+200/47) |
| 1938 |
compute in5 @*(1+200/20), @/(1+200/20) |
| 1939 |
compute in8 @*(1+200/47), @/(1+200/47) |
| 1940 |
|
| 1941 |
# in0 is the chip's own VCC. |
| 1942 |
set in0_min 3.0 |
| 1943 |
set in0_max 3.6 |
| 1944 |
|
| 1945 |
#set in1_min 1.2 * 0.95 |
| 1946 |
#set in1_max 1.2 * 1.05 |
| 1947 |
#set in2_min 2.5 * 0.95 |
| 1948 |
#set in2_max 2.6 * 1.05 |
| 1949 |
#set in3_min 3.3 * 0.95 |
| 1950 |
#set in3_max 3.3 * 1.05 |
| 1951 |
#set in4_min 5.0 * 0.95 |
| 1952 |
#set in4_max 5.0 * 1.05 |
| 1953 |
#set in5_min 12.0 * 0.95 |
| 1954 |
#set in5_max 12.0 * 1.05 |
| 1955 |
#set in6_min 1.5 * 0.95 |
| 1956 |
#set in6_max 1.5 * 1.05 |
| 1957 |
# in7 nominal value depends on the CPU model |
| 1958 |
#set in7_min 1.4 * 0.95 |
| 1959 |
#set in7_max 1.4 * 1.05 |
| 1960 |
#set in8_min 5.0 * 0.95 |
| 1961 |
#set in8_max 5.0 * 1.05 |
| 1962 |
|
| 1963 |
# Fans |
| 1964 |
label fan1 "CPU Fan" |
| 1965 |
label fan2 "Sys Fan" |
| 1966 |
label fan3 "Aux Fan" |
| 1967 |
|
| 1968 |
#set fan1_min 2100 |
| 1969 |
#set fan2_min 1400 |
| 1970 |
#set fan3_min 1400 |
| 1971 |
|
| 1972 |
# Temperatures |
| 1973 |
label temp1 "CPU Temp" |
| 1974 |
label temp2 "Sys Temp" |
| 1975 |
label temp3 "Aux Temp" |
| 1976 |
|
| 1977 |
#set temp1_max 60 |
| 1978 |
#set temp1_max_hyst 58 |
| 1979 |
#set temp2_max 50 |
| 1980 |
#set temp2_max_hyst 48 |
| 1981 |
#set temp3_max 50 |
| 1982 |
#set temp3_max_hyst 48 |
| 1983 |
|
| 1984 |
|
| 1985 |
# Abit Uguru sensor part configuration. |
| 1986 |
# The Abit Uguru is relatively straight forward to configure. |
| 1987 |
# label statements: |
| 1988 |
# The voltage (in) temp and fan sensors are usually in the same order as listed |
| 1989 |
# in the BIOS, but not always! |
| 1990 |
# compute statements: |
| 1991 |
# The temp and fan sensors don't need any compute statements. Most voltage |
| 1992 |
# inputs are directly connected to the IC and thus don't need an compute line |
| 1993 |
# because the 0-3494 mV voltage given by the kernel driver is correct. The sen- |
| 1994 |
# sors for higher voltages however are connect through a divider and measure |
| 1995 |
# ranges of: 0-4361mV, 0-6248mV or 0-14510mV. Thus the measured voltages must |
| 1996 |
# be multiplied by resp. 1.248, 1.788 or 4.153. 3.3 volt sources use the 1.248 |
| 1997 |
# mutiplier, 5 volt the 1.788 and 12 volt the 4.153. |
| 1998 |
# set statements: |
| 1999 |
# The Abit BIOS sets reasonable treshholds and allows changing them, thus |
| 2000 |
# set statements may be omitted. The abituguru kernel driver does support |
| 2001 |
# them if you want to add them. |
| 2002 |
# |
| 2003 |
# The configuration below is for the Kv8Pro and AV8 this is the default as this |
| 2004 |
# driver is developed and tested on a Kv8Pro. |
| 2005 |
# Configurations for many other Abit boards can be found at: |
| 2006 |
# https://github.com/lm-sensors/lm-sensors/tree/master/configs/Abit |
| 2007 |
# If your motherboard isn't listed there and you create a configuration for it |
| 2008 |
# please add it there. |
| 2009 |
|
| 2010 |
chip "abituguru-*" |
| 2011 |
|
| 2012 |
label in0 "CPU Core Voltage" |
| 2013 |
label in1 "DDR Voltage" |
| 2014 |
label in2 "DDR VTT Voltage" |
| 2015 |
label in3 "NB Voltage" |
| 2016 |
label in4 "SB Voltage" |
| 2017 |
label in5 "HyperTransport Voltage" |
| 2018 |
label in6 "AGP VDDQ Voltage" |
| 2019 |
label in7 "ATX +5V" |
| 2020 |
compute in7 @*1.788 , @/1.788 |
| 2021 |
label in8 "ATX +3.3V" |
| 2022 |
compute in8 @*1.248 , @/1.248 |
| 2023 |
label in9 "Standby Voltage (+5V)" |
| 2024 |
compute in9 @*1.788 , @/1.788 |
| 2025 |
label in10 "3VDual Voltage" |
| 2026 |
compute in10 @*1.248 , @/1.248 |
| 2027 |
|
| 2028 |
label temp1 "CPU Temperature" |
| 2029 |
label temp2 "SYS Temperature" |
| 2030 |
label temp3 "PWM Temperature" |
| 2031 |
ignore temp4 |
| 2032 |
ignore temp5 |
| 2033 |
ignore temp6 |
| 2034 |
ignore temp7 |
| 2035 |
|
| 2036 |
label fan1 "CPU FAN Speed" |
| 2037 |
label fan2 "NB FAN Speed" |
| 2038 |
label fan3 "SYS FAN Speed" |
| 2039 |
label fan4 "AUX1 FAN Speed" |
| 2040 |
label fan5 "AUX2 FAN Speed" |
| 2041 |
ignore fan6 |
| 2042 |
|
| 2043 |
chip "k8temp-*" |
| 2044 |
|
| 2045 |
label temp1 "Core0 Temp" |
| 2046 |
label temp2 "Core0 Temp" |
| 2047 |
label temp3 "Core1 Temp" |
| 2048 |
label temp4 "Core1 Temp" |
| 2049 |
|
| 2050 |
|
| 2051 |
# |
| 2052 |
# Sample configuration for the SMSC DME1737 and ASUS A8000 |
| 2053 |
# |
| 2054 |
chip "dme1737-*" |
| 2055 |
|
| 2056 |
# Voltage inputs |
| 2057 |
label in0 "V5stby" |
| 2058 |
label in1 "Vccp" |
| 2059 |
label in2 "V3.3" |
| 2060 |
label in3 "V5" |
| 2061 |
label in4 "V12" |
| 2062 |
label in5 "V3.3stby" |
| 2063 |
label in6 "Vbat" |
| 2064 |
|
| 2065 |
# Temperature inputs |
| 2066 |
label temp1 "RD1 Temp" |
| 2067 |
label temp2 "Int Temp" |
| 2068 |
label temp3 "CPU Temp" |
| 2069 |
|
| 2070 |
# Fan inputs |
| 2071 |
label fan1 "CPU Fan" |
| 2072 |
|
| 2073 |
# Set voltage limits |
| 2074 |
# set in0_min 5.0 * 0.95 |
| 2075 |
# set in0_max 5.0 * 1.05 |
| 2076 |
# set in1_min 1.4 * 0.95 |
| 2077 |
# set in1_max 1.4 * 1.05 |
| 2078 |
# set in2_min 3.3 * 0.95 |
| 2079 |
# set in2_max 3.3 * 1.05 |
| 2080 |
# set in3_min 5.0 * 0.95 |
| 2081 |
# set in3_max 5.0 * 1.05 |
| 2082 |
# set in4_min 12.0 * 0.95 |
| 2083 |
# set in4_max 12.0 * 1.05 |
| 2084 |
# set in5_min 3.3 * 0.95 |
| 2085 |
# set in5_max 3.3 * 1.05 |
| 2086 |
# set in6_min 3.0 * 0.95 |
| 2087 |
# set in6_max 3.0 * 1.05 |
| 2088 |
|
| 2089 |
# Set Temp Limits |
| 2090 |
# set temp1_min 10 |
| 2091 |
# set temp1_max 75 |
| 2092 |
# set temp2_min 10 |
| 2093 |
# set temp2_max 75 |
| 2094 |
# set temp3_min 10 |
| 2095 |
# set temp3_max 75 |
| 2096 |
|
| 2097 |
# Set Fan limits |
| 2098 |
# set fan1_min 1000 |
| 2099 |
# set fan2_min 1000 |
| 2100 |
# set fan3_min 1000 |
| 2101 |
# set fan4_min 1000 |
| 2102 |
# set fan5_min 1000 |
| 2103 |
# set fan6_min 1000 |
| 2104 |
|
| 2105 |
|
| 2106 |
# |
| 2107 |
# sample configuration for the Fintek f71882fg and f71883fg |
| 2108 |
# |
| 2109 |
# The configuration below is for the Epox EP-9U1697 GLI board, which has a |
| 2110 |
# Fintek f71883fg relabeled as Epox ep1308, this is the default config as this |
| 2111 |
# driver is developed and tested on an Epox EP-9U1697 GLI board. |
| 2112 |
# |
| 2113 |
# Premade configurations for other boards can be found at: |
| 2114 |
# https://github.com/lm-sensors/lm-sensors/tree/master/configs |
| 2115 |
# If your motherboard isn't listed there and you create a configuration for it |
| 2116 |
# please add it there. |
| 2117 |
# |
| 2118 |
chip "f71882fg-*" |
| 2119 |
|
| 2120 |
# Temperature |
| 2121 |
label temp1 "CPU" |
| 2122 |
label temp2 "System" |
| 2123 |
ignore temp3 |
| 2124 |
|
| 2125 |
# Fans |
| 2126 |
label fan1 "CPU" |
| 2127 |
label fan2 "System" |
| 2128 |
label fan3 "Power" |
| 2129 |
label fan4 "Aux" |
| 2130 |
|
| 2131 |
# Voltage |
| 2132 |
label in0 "3.3V" |
| 2133 |
label in1 "Vcore" |
| 2134 |
label in2 "Vdimm" |
| 2135 |
label in3 "Vchip" |
| 2136 |
label in4 "+5V" |
| 2137 |
label in5 "12V" |
| 2138 |
label in6 "5VSB" |
| 2139 |
label in7 "3VSB" |
| 2140 |
label in8 "Battery" |
| 2141 |
|
| 2142 |
# never change the in0, in7 and in8 compute, these are hardwired in the chip! |
| 2143 |
compute in0 (@ * 2), (@ / 2) |
| 2144 |
compute in2 (@ * 2), (@ / 2) |
| 2145 |
compute in3 (@ * 2), (@ / 2) |
| 2146 |
compute in4 (@ * 5.25), (@ / 5.25) |
| 2147 |
compute in5 (@ * 12.83), (@ / 12.83) |
| 2148 |
compute in6 (@ * 5.25), (@ / 5.25) |
| 2149 |
compute in7 (@ * 2), (@ / 2) |
| 2150 |
compute in8 (@ * 2), (@ / 2) |
| 2151 |
|
| 2152 |
|
| 2153 |
chip "adm1022-*" "thmc50-*" |
| 2154 |
|
| 2155 |
label temp1 "M/B Temp" |
| 2156 |
# Single CPU setup |
| 2157 |
label temp2 "CPU Temp" |
| 2158 |
|
| 2159 |
# Dual CPU setup (ADM1022 only) |
| 2160 |
#label temp2 "CPU0 Temp" |
| 2161 |
#label temp3 "CPU1 Temp" |
| 2162 |
|
| 2163 |
# Asus/Fintek F8000 |
| 2164 |
chip "f8000-*" |
| 2165 |
|
| 2166 |
# All 3 voltages are internal, but scaling is not done by the driver |
| 2167 |
# so we do it here |
| 2168 |
compute in0 @*2, @/2 |
| 2169 |
compute in1 @*2, @/2 |
| 2170 |
compute in2 @*2, @/2 |
| 2171 |
|
| 2172 |
label in0 "+3.3V" |
| 2173 |
label in1 "3VSB" |
| 2174 |
label in2 "Vbat" |