| 1 |
Sat May 12 12:00 2001 Gerard Roudier ([email protected]) |
| 2 |
* version sym53c8xx-1.7.3c |
| 3 |
- Ensure LEDC bit in GPCNTL is cleared when reading the NVRAM. |
| 4 |
Fix sent by Stig Telfer <[email protected]>. |
| 5 |
- Backport from SYM-2 the work-around that allows to support |
| 6 |
hardware that fails PCI parity checking. |
| 7 |
- Check that we received at least 8 bytes of INQUIRY response |
| 8 |
for byte 7, that contains device capabilities, to be valid. |
| 9 |
- Define scsi_set_pci_device() as nil for kernel < 2.4.4. |
| 10 |
- + A couple of minor changes. |
| 11 |
|
| 12 |
Sat Apr 7 19:30 2001 Gerard Roudier ([email protected]) |
| 13 |
* version sym53c8xx-1.7.3b |
| 14 |
- Fix an unaligned LOAD from scripts (was used as dummy read). |
| 15 |
- In ncr_soft_reset(), only try to ABORT the current operation |
| 16 |
for chips that support SRUN bit in ISTAT1 and if SCRIPTS are |
| 17 |
currently running, as 896 and 1010 manuals suggest. |
| 18 |
- In the CCB abort path, do not assume that the CCB is currently |
| 19 |
queued to SCRIPTS. This is not always true, notably after a |
| 20 |
QUEUE FULL status or when using untagged commands. |
| 21 |
|
| 22 |
Sun Mar 4 18:30 2001 Gerard Roudier ([email protected]) |
| 23 |
* version sym53c8xx-1.7.3a |
| 24 |
- Fix an issue in the ncr_int_udc() (unexpected disconnect) |
| 25 |
handling. If the DSA didn't match a CCB, a bad write to |
| 26 |
memory could happen. |
| 27 |
|
| 28 |
Mon Feb 12 22:30 2001 Gerard Roudier ([email protected]) |
| 29 |
* version sym53c8xx-1.7.3 |
| 30 |
- Support for hppa. |
| 31 |
Tiny patch sent to me by Robert Hirst. |
| 32 |
- Tiny patch for ia64 sent to me by Pamela Delaney. |
| 33 |
|
| 34 |
Tue Feb 6 13:30 2001 Gerard Roudier ([email protected]) |
| 35 |
* version sym53c8xx-1.7.3-pre1 |
| 36 |
- Call pci_enable_device() as AC wants this to be done. |
| 37 |
- Get both the BAR cookies used by CPU and actual PCI BAR |
| 38 |
values used from SCRIPTS. Recent PCI chips are able to |
| 39 |
access themselves using internal cycles, but they compare |
| 40 |
BAR values to destination address to make decision. |
| 41 |
Earlier chips simply use PCI transactions to access IO |
| 42 |
registers from SCRIPTS. |
| 43 |
The bus_dvma_to_mem() interface that reverses the actual |
| 44 |
PCI BAR value from the BAR cookie is now useless. |
| 45 |
This point had been discussed at the list and the solution |
| 46 |
got approved by PCI code maintainer (Martin Mares). |
| 47 |
- Merge changes for linux-2.4 that declare the host template |
| 48 |
in the driver object also when the driver is statically |
| 49 |
linked with the kernel. |
| 50 |
- Increase SCSI message size up to 12 bytes, given that 8 |
| 51 |
bytes was not enough for the PPR message (fix). |
| 52 |
- Add field 'maxoffs_st' (max offset for ST data transfers). |
| 53 |
The C1010 supports offset 62 in DT mode but only 31 in |
| 54 |
ST mode, to 2 different values for the max SCSI offset |
| 55 |
are needed. Replace the obviously wrong masking of the |
| 56 |
offset against 0x1f for ST mode by a lowering to |
| 57 |
maxoffs_st of the SCSI offset in ST mode. |
| 58 |
- Refine a work-around for the C1010-66. Revision 1 does |
| 59 |
not requires extra cycles in DT DATA OUT phase. |
| 60 |
- Add a missing endian-ization (abrt_tbl.addr). |
| 61 |
- Minor clean-up in the np structure for fields accessed |
| 62 |
from SCRIPTS that requires special alignments. |
| 63 |
|
| 64 |
Sun Sep 24 21:30 2000 Gerard Roudier ([email protected]) |
| 65 |
* version sym53c8xx-1.7.2 |
| 66 |
- Remove the hack for PPC added in previous driver version. |
| 67 |
- Add FE_DAC feature bit to distinguish between 64 bit PCI |
| 68 |
addressing (FE_DAC) and 64 bit PCI interface (FE_64BIT). |
| 69 |
- Get rid of the boot command line "ultra:" argument. |
| 70 |
This parameter wasn't that clever since we can use "sync:" |
| 71 |
for Ultra/Ultra2 settings, and for Ultra3 we may want to |
| 72 |
pass PPR options (for now only DT clocking). |
| 73 |
- Add FE_VARCLK feature bit that indicates that SCSI clock |
| 74 |
frequency may vary depending on board design and thus, |
| 75 |
the driver should try to evaluate the SCSI clock. |
| 76 |
- Simplify the way the driver determine the SCSI clock: |
| 77 |
ULTRA3 -> 160 MHz, ULTRA2 -> 80 MHz otherwise 40 MHz. |
| 78 |
Measure the SCSI clock frequency if FE_VARCLK is set. |
| 79 |
- Remove FE_CLK80 feature bit that got useless. |
| 80 |
- Add support for the SYM53C875A (Pamela Delaney). |
| 81 |
|
| 82 |
Wed Jul 26 23:30 2000 Gerard Roudier ([email protected]) |
| 83 |
* version sym53c8xx-1.7.1 |
| 84 |
- Provide OpenFirmware path through the proc FS on PPC. |
| 85 |
- Download of on-chip SRAM using memcpy_toio() doesn't work |
| 86 |
on PPC. Restore previous method (MEMORY MOVE from SCRIPTS). |
| 87 |
- Remove trailing argument #2 from a couple of #undefs. |
| 88 |
|
| 89 |
Sun Jul 09 16:30 2000 Gerard Roudier ([email protected]) |
| 90 |
* version sym53c8xx-1.7.0 |
| 91 |
- Remove the PROFILE C and SCRIPTS code. |
| 92 |
This facility was not this useful and thus was not longer |
| 93 |
desirable given the increasing complexity of the driver code. |
| 94 |
- Merges from FreeBSD sym-1.6.2 driver: |
| 95 |
* Clarify memory barriers needed by the driver for architectures |
| 96 |
that implement a weak memory ordering. |
| 97 |
* Simpler handling of illegal phases and data overrun from |
| 98 |
SCRIPTS. These errors are now immediately reported to |
| 99 |
the C code by an interrupt. |
| 100 |
* Sync the residual handling code with sym-1.6.2 and now |
| 101 |
report `resid' to user for linux version >= 2.3.99 |
| 102 |
- General cleanup: |
| 103 |
Move definitions for barriers and IO/MMIO operations to the |
| 104 |
sym53c8xx_defs.h header files. They are now shared by the |
| 105 |
both drivers. |
| 106 |
Remove unused options that claimed to optimize for the 896. |
| 107 |
If fact, they were not this clever. :) |
| 108 |
Use SCSI_NCR_IOMAPPED instead of NCR_IOMAPPED. |
| 109 |
Remove a couple of unused fields from data structures. |
| 110 |
|
| 111 |
Thu May 11 12:40 2000 Pam Delaney ([email protected]) |
| 112 |
* version sym53c8xx-1.6b |
| 113 |
- Merged version. |
| 114 |
|
| 115 |
Mon Apr 24 12:00 2000 Gerard Roudier ([email protected]) |
| 116 |
* version sym53c8xx-1.5m |
| 117 |
- Return value 1 (instead of 0) from the driver setup routine. |
| 118 |
- Do not enable PCI DAC cycles. This just broke support for |
| 119 |
SYM534C896 on sparc64. Problem fixed by David S. Miller. |
| 120 |
|
| 121 |
Fri Apr 14 9:00 2000 Pam Delaney ([email protected]) |
| 122 |
* version sym53c8xx-1.6b-9 |
| 123 |
- Added 53C1010_66 support. |
| 124 |
- Small fix to integrity checking code. |
| 125 |
- Removed requirement for integrity checking if want to run |
| 126 |
at ultra 3. |
| 127 |
|
| 128 |
Sat Apr 1 12:00 2000 Gerard Roudier ([email protected]) |
| 129 |
* version sym53c8xx-1.5l |
| 130 |
- Tiny change for __sparc__ appeared in 2.3.99-pre4.1 that |
| 131 |
applies to cache line size (? Probably from David S Miller). |
| 132 |
- Make sure no data transfer will happen for Scsi_Cmnd requests |
| 133 |
that supply SCSI_DATA_NONE direction (this avoids some BUG() |
| 134 |
statement in the PCI code when a data buffer is also supplied). |
| 135 |
|
| 136 |
Sat Mar 11 12:00 2000 Gerard Roudier ([email protected]) |
| 137 |
* version sym53c8xx-1.6b-5 |
| 138 |
- Test against expected data transfer direction from SCRIPTS. |
| 139 |
- Add support for the new dynamic dma mapping kernel interface. |
| 140 |
Requires Linux-2.3.47 (tested with pre-2.3.47-6). |
| 141 |
Many thanks to David S. Miller for his preliminary changes |
| 142 |
that have been useful guidelines. |
| 143 |
- Get data transfer direction from the scsi command structure |
| 144 |
(Scsi_Cmnd) with kernels that provide this information. |
| 145 |
|
| 146 |
Mon Mar 6 23:30 2000 Gerard Roudier ([email protected]) |
| 147 |
* version sym53c8xx-1.5k |
| 148 |
- Test against expected data transfer direction from SCRIPTS. |
| 149 |
- Revert the change in 'ncr_flush_done_cmds()' but unmap the |
| 150 |
scsi dma buffer prior to queueing the command to our done |
| 151 |
list. |
| 152 |
- Miscellaneous (minor) fixes in the code added in driver |
| 153 |
version 1.5j. |
| 154 |
|
| 155 |
Mon Feb 14 4:00 2000 Pam Delaney ([email protected]) |
| 156 |
* version sym53c8xx-pre-1.6b-2. |
| 157 |
- Updated the SCRIPTS error handling of the SWIDE |
| 158 |
condition - to remove any reads of the sbdl |
| 159 |
register. Changes needed because the 896 and 1010 |
| 160 |
chips will check parity in some special circumstances. |
| 161 |
This will cause a parity error interrupt if not in |
| 162 |
data phase. Changes based on those made in the |
| 163 |
FreeBSD driver version 1.3.2. |
| 164 |
|
| 165 |
Sun Feb 20 11:00 2000 Gerard Roudier ([email protected]) |
| 166 |
* version sym53c8xx-1.5j |
| 167 |
- Add support for the new dynamic dma mapping kernel interface. |
| 168 |
Requires Linux-2.3.47 (tested with pre-2.3.47-6). |
| 169 |
Many thanks to David S. Miller for his preliminary changes |
| 170 |
that have been useful guidelines, for having reviewed the |
| 171 |
code and having tested this driver version on Ultra-Sparc. |
| 172 |
- 2 tiny bugs fixed in the PCI wrapper that provides support |
| 173 |
for early kernels without pci device structure. |
| 174 |
- Get data transfer direction from the scsi command structure |
| 175 |
(Scsi_Cmnd) with kernels that provide this information. |
| 176 |
- Fix an old bug that only affected 896 rev. 1 when driver |
| 177 |
profile support option was set in kernel configuration. |
| 178 |
|
| 179 |
Fri Jan 14 14:00 2000 Pam Delaney ([email protected]) |
| 180 |
* version sym53c8xx-pre-1.6b-1. |
| 181 |
- Merge parallel driver series 1.61 and 1.5e |
| 182 |
|
| 183 |
Tue Jan 11 14:00 2000 Pam Delaney ([email protected]) |
| 184 |
* version sym53c8xx-1.61 |
| 185 |
- Added support for mounting disks on wide-narrow-wide |
| 186 |
scsi configurations. |
| 187 |
- Modified offset to be a maximum of 31 in ST mode, |
| 188 |
62 in DT mode. |
| 189 |
- Based off of 1.60 |
| 190 |
|
| 191 |
Mon Jan 10 10:00 2000 Pam Delaney ([email protected]) |
| 192 |
* version sym53c8xx-1.60 |
| 193 |
- Added capability to use the integrity checking code |
| 194 |
in the kernel (optional). |
| 195 |
- Added PPR negotiation. |
| 196 |
- Added support for 53C1010 Ultra 3 part. |
| 197 |
- Based off of 1.5f |
| 198 |
|
| 199 |
Sat Jan 8 22:00 2000 Gerard Roudier ([email protected]) |
| 200 |
* version sym53c8xx-1.5h |
| 201 |
- Add year 2000 copyright. |
| 202 |
- Display correctly bus signals when bus is detected wrong. |
| 203 |
- Some fix for Sparc from DSM that went directly to kernel tree. |
| 204 |
|
| 205 |
Mon Dec 6 22:00 1999 Gerard Roudier ([email protected]) |
| 206 |
* version sym53c8xx-1.5g |
| 207 |
- Change messages written by the driver at initialisation and |
| 208 |
through the /proc FS (rather cosmetic changes that consist in |
| 209 |
printing out the PCI bus number and PCI device/function). |
| 210 |
- Ensure the SCRIPTS processor is stopped while calibrating the |
| 211 |
SCSI clock (the initialisation code has been a bit reworked). |
| 212 |
Change moved to the FreeBSD sym_hipd driver). |
| 213 |
- Some fixes in the MODIFY_DP/IGN_RESIDUE code and residual |
| 214 |
calculation (moved from FreeBSD sym_hipd driver). |
| 215 |
- Add NVRAM support for Tekram boards that use 24C16 EEPROM. |
| 216 |
Code moved from the FreeBSD sym_hipd driver, since it has |
| 217 |
been that one that got this feature first. |
| 218 |
- Definitely disable overlapped PCI arbitration for all dual |
| 219 |
function chips, since I cannot make sure for what chip revisions |
| 220 |
it is actually safe. |
| 221 |
- Add support for the SYM53C1510D (also for ncr53c8xx). |
| 222 |
- Fix up properly the PCI latency timer when needed or asked for. |
| 223 |
- Get rid of the old PCI bios interface, but preserve kernel 2.0 |
| 224 |
compatibility from a simple wrapper. |
| 225 |
- Update the poor Tekram sync factor table. |
| 226 |
- Fix in a tiny 'printk' bug that may oops in case of extended |
| 227 |
errors (unrecovered parity error, data overrun, etc ...) |
| 228 |
(Sent by Pamela Delaney from LSILOGIC) |
| 229 |
- Remove the compilation condition about having to acquire the |
| 230 |
io_request_lock since it seems to be a definite feature now.:) |
| 231 |
- Change get_pages by GetPages since Linux >= 2.3.27 now wants |
| 232 |
get_pages to ever be used as a kernel symbol (from 2.3.27). |
| 233 |
- proc_dir structure no longer needed for kernel >= 2.3.27. |
| 234 |
|
| 235 |
Sun Oct 3 19:00 1999 Gerard Roudier ([email protected]) |
| 236 |
* version sym53c8xx-1.5f |
| 237 |
- Change the way the driver checks the PCI clock frequency, so |
| 238 |
that overclocked PCI BUS up to 48 MHz will not be refused. |
| 239 |
The more the BUS is overclocked, the less the driver will |
| 240 |
guarantee that its measure of the SCSI clock is correct. |
| 241 |
- Backport some minor improvements of SCRIPTS from the sym_hipd |
| 242 |
driver. |
| 243 |
- Backport the code rewrite of the START QUEUE dequeuing (on |
| 244 |
bad scsi status received) from the sym_hipd driver. |
| 245 |
|
| 246 |
Sat Sep 11 11:00 1999 Gerard Roudier ([email protected]) |
| 247 |
* version sym53c8xx-1.5e |
| 248 |
- New linux-2.3.13 __setup scheme support added. |
| 249 |
- Cleanup of the extended error status handling: |
| 250 |
Use 1 bit per error type. |
| 251 |
- Also save the extended error status prior to auto-sense. |
| 252 |
- Add the FE_DIFF chip feature bit to indicate support of |
| 253 |
diff probing from GPIO3 (825/825A/876/875). |
| 254 |
- Remove the quirk handling that has been useless since day one. |
| 255 |
- Work-around PCI chips being reported twice on some platforms. |
| 256 |
- Add some redundant PCI reads in order to deal with common |
| 257 |
bridge misbehaviour regarding posted write flushing. |
| 258 |
- Add some other conditional code for people who have to deal |
| 259 |
with really broken bridges (they will have to edit a source |
| 260 |
file to try these options). |
| 261 |
- Handle correctly (hopefully) jiffies wrap-around. |
| 262 |
- Restore the entry used to detect 875 until revision 0xff. |
| 263 |
(I removed it inadvertently, it seems :) ) |
| 264 |
- Replace __initfunc() which is deprecated stuff by __init which |
| 265 |
is not yet so. ;-) |
| 266 |
- Rewrite the MESSAGE IN scripts more generic by using a MOVE |
| 267 |
table indirect. Extended messages of any size are accepted now. |
| 268 |
(Size is limited to 8 for now, but a constant is just to be |
| 269 |
increased if necessary) |
| 270 |
- Fix some bug in the fully untested MDP handling:) and share |
| 271 |
some code between MDP handling and residual calculation. |
| 272 |
- Calculate the data transfer residual as the 2's complement |
| 273 |
integer (A positive value in returned on data overrun, and |
| 274 |
a negative one on underrun). |
| 275 |
- Add support of some 'resource handling' for linux-2.3.13. |
| 276 |
Basically the BARs have been changed to something more complex |
| 277 |
in the pci_dev structure. |
| 278 |
- Remove some deprecated code. |
| 279 |
|
| 280 |
Sat Jun 5 11:00 1999 Gerard Roudier ([email protected]) |
| 281 |
* version sym53c8xx-1.5c |
| 282 |
- Do not negotiate on auto-sense if we are currently using 8 bit |
| 283 |
async transfer for the target. |
| 284 |
- Only check for SISL/RAID on i386 platforms. |
| 285 |
(A problem has been reported on PPC with that code). |
| 286 |
- On MSG REJECT for a negotiation, the driver attempted to restart |
| 287 |
the SCRIPT processor when this one was already running. |
| 288 |
|
| 289 |
Sat May 29 12:00 1999 Gerard Roudier ([email protected]) |
| 290 |
* version sym53c8xx-1.5b |
| 291 |
- Force negotiation prior auto-sense. |
| 292 |
This ensures that the driver will be able to grab the sense data |
| 293 |
from a device that has received a BUS DEVICE RESET message from |
| 294 |
another initiator. |
| 295 |
- Complete all disconnected CCBs for a logical UNIT if we are told |
| 296 |
about a UNIT ATTENTION for a RESET condition by this target. |
| 297 |
- Add the control command 'cleardev' that allows to send a ABORT |
| 298 |
message to a logical UNIT (for test purpose). |
| 299 |
|
| 300 |
Tue May 25 23:00 1999 Gerard Roudier ([email protected]) |
| 301 |
* version sym53c8xx-1.5a |
| 302 |
- Add support for task abort and bus device reset SCSI message |
| 303 |
and implement proper synchronisation with SCRIPTS to handle |
| 304 |
correctly task abortion without races. |
| 305 |
- Send an ABORT message (if untagged) or ABORT TAG message (if tagged) |
| 306 |
when the driver is told to abort a command that is disconnected and |
| 307 |
complete the command with appropriate error. |
| 308 |
If the aborted command is not yet started, remove it from the start |
| 309 |
queue and complete it with error. |
| 310 |
- Add the control command 'resetdev' that allows to send a BUS |
| 311 |
DEVICE RESET message to a target (for test purpose). |
| 312 |
- Clean-up some unused or useless code. |
| 313 |
|
| 314 |
Fri May 21 23:00 1999 Gerard Roudier ([email protected]) |
| 315 |
* version sym53c8xx-1.5 |
| 316 |
- Add support for CHMOV with Wide controllers. |
| 317 |
- Handling of the SWIDE (low byte residue at the end of a CHMOV |
| 318 |
in DATA IN phase with WIDE transfer when the byte count gets odd). |
| 319 |
- Handling of the IGNORE WIDE RESIDUE message. |
| 320 |
Handled from SCRIPTS as possible with some optimizations when both |
| 321 |
a wide device and the controller are odd at the same time (SWIDE |
| 322 |
present and IGNORE WIDE RESIDUE message on the BUS at the same time). |
| 323 |
- Check against data OVERRUN/UNDERRUN condition at the end of a data |
| 324 |
transfer, whatever a SWIDE is present (OVERRUN in DATA IN phase) |
| 325 |
or the SODL is full (UNDERRUN in DATA out phase). |
| 326 |
- Handling of the MODIFY DATA POINTER message. |
| 327 |
This one cannot be handled from SCRIPTS, but hopefully it will not |
| 328 |
happen very often. :) |
| 329 |
- Large rewrite of the SCSI MESSAGE handling. |
| 330 |
|
| 331 |
Sun May 9 11:00 1999 Gerard Roudier ([email protected]) |
| 332 |
* version sym53c8xx-1.4 |
| 333 |
- Support for IMMEDIATE ARBITRATION. |
| 334 |
See the README file for detailed information about this feature. |
| 335 |
Requires both a compile option and a boot option. |
| 336 |
- Minor SCRIPTS optimization in reselection pattern for LUN 0. |
| 337 |
- Simpler algorithm to deal with SCSI command starvation. |
| 338 |
Just use 2 tag counters in flip/flop and switch to the other |
| 339 |
one every 3 seconds. |
| 340 |
- Do some work in SCRIPTS after the SELECT instruction and prior |
| 341 |
to testing for a PHASE. SYMBIOS say this feature is working fine. |
| 342 |
(Btw, only problems with Toshiba 3401B had been reported). |
| 343 |
- Measure the PCI clock speed and do not attach controllers if |
| 344 |
result is greater than 37 MHz. Since the precision of the |
| 345 |
algorithm (from Stefan Esser) is better than 2%, this should |
| 346 |
be fine. |
| 347 |
- Fix the misdetection of SYM53C875E (was detected as a 876). |
| 348 |
- Fix the misdetection of SYM53C810 not A (was detected as a 810A). |
| 349 |
- Support for up to 256 TAGS per LUN (CMD_PER_LUN). |
| 350 |
Currently limited to 255 due to Linux limitation. :) |
| 351 |
- Support for up to 508 active commands (CAN_QUEUE). |
| 352 |
- Support for the 53C895A by Pamela Delaney <[email protected]> |
| 353 |
The 53C895A contains all of the features of the 896 but has only |
| 354 |
one channel and has a 32 bit PCI bus. It does 64 bit PCI addressing |
| 355 |
using dual cycle PCI data transfers. |
| 356 |
- Miscellaneous minor fixes. |
| 357 |
- Some additions to the README.ncr53c8xx file. |
| 358 |
|
| 359 |
Tue Apr 15 10:00 1999 Gerard Roudier ([email protected]) |
| 360 |
* version sym53c8xx-1.3e |
| 361 |
- Support for any number of LUNs (64) (SPI2-compliant). |
| 362 |
(Btw, this may only be ever useful under linux-2.2 ;-)) |
| 363 |
|
| 364 |
Sun Apr 11 10:00 1999 Gerard Roudier ([email protected]) |
| 365 |
* version sym53c8xx-1.3d |
| 366 |
- Add 'hostid:#id' boot option. This option allows to change the |
| 367 |
default SCSI id the driver uses for controllers. |
| 368 |
- Make SCRIPTS not use self-mastering for PCI. |
| 369 |
There were still 2 places the driver used this feature of the |
| 370 |
53C8XX family. |
| 371 |
- Move some data structures (nvram layouts and driver set-up) to |
| 372 |
the sym53c8xx_defs.h file. So, the both drivers will share them. |
| 373 |
- Set MAX LUNS to 16 (instead of 8). |
| 374 |
|
| 375 |
Sat Mar 20 21:00 1999 Gerard Roudier ([email protected]) |
| 376 |
* version sym53c8xx-1.3b |
| 377 |
- Add support for NCR PQS PDS. |
| 378 |
James Bottomley <[email protected]> |
| 379 |
- Allow value 0 for host ID. |
| 380 |
- Support more than 8 controllers (> 40 in fact :-) ) |
| 381 |
- Add 'excl=#ioaddr' boot option: exclude controller. |
| 382 |
(Version 1.3a driver) |
| 383 |
|
| 384 |
Thu Mar 11 23:00 1999 Gerard Roudier ([email protected]) |
| 385 |
* version sym53c8xx-1.3 (8xx-896 driver bundle) |
| 386 |
- Equivalent changes as ncr53c8xx-3.2 due to the driver bundle. |
| 387 |
(See Changelog.ncr53c8xx) |
| 388 |
- Do a normal soft reset as first chip reset, since aborting current |
| 389 |
operation may raise an interrupt we are not able to handle since |
| 390 |
the interrupt handler is not yet established. |
| 391 |
|
| 392 |
Sat Mar 6 11:00 1999 Gerard Roudier ([email protected]) |
| 393 |
* version sym53c8xx-1.2b |
| 394 |
- Fix some oooold bug that hangs the bus if a device rejects a |
| 395 |
negotiation. Btw, the corresponding stuff also needed some cleanup |
| 396 |
and thus the change is a bit larger than it could have been. |
| 397 |
- Still some typo that made compilation fail for 64 bit (trivial fix). |
| 398 |
|
| 399 |
Sun Feb 21 20:00 1999 Gerard Roudier ([email protected]) |
| 400 |
* version sym53c8xx-1.2a |
| 401 |
- The rewrite of the interrupt handling broke the SBMC interrupt |
| 402 |
handling due to a 1 bit mask tiny error. Hopefully fixed. |
| 403 |
- If INQUIRY came from a scatter list, the driver looked into |
| 404 |
the scatterlist instead of the data.:) Since this should never |
| 405 |
happen, we just discard the data if use_sg is not zero. |
| 406 |
|
| 407 |
Fri Feb 12 23:00 1999 Gerard Roudier ([email protected]) |
| 408 |
* version sym53c8xx-1.2 |
| 409 |
- Major rewrite of the interrupt handling and recovery stuff for |
| 410 |
the support of non compliant SCSI removal, insertion and all |
| 411 |
kinds of screw-up that may happen on the SCSI BUS. |
| 412 |
Hopefully, the driver is now unbreakable or may-be, it is just |
| 413 |
quite broken. :-) |
| 414 |
Many thanks to Johnson Russel (Symbios) for having responded to |
| 415 |
my questions and for his interesting advices and comments about |
| 416 |
support of SCSI hot-plug. |
| 417 |
- Add 'recovery' option to driver set-up. |
| 418 |
- Negotiate SYNC data transfers with CCS devices. |
| 419 |
- Deal correctly with 64 bit PCI address registers on Linux 2.2. |
| 420 |
Pointed out by Leonard Zubkoff. |
| 421 |
|
| 422 |
Sun Jan 31 18:00 1999 Gerard Roudier ([email protected]) |
| 423 |
* version sym53c8xx-1.1a |
| 424 |
- Some 896 chip revisions (all for now :-)), may hang-up if the |
| 425 |
soft reset bit is set at the wrong time while SCRIPTS are running. |
| 426 |
We need to first abort the current SCRIPTS operation prior to |
| 427 |
resetting the chip. This fix has been sent to me by SYMBIOS/LSI |
| 428 |
and I just translated it into ncr53c8xx syntax. |
| 429 |
Must be considered 100 % trustable, unless I did some mistake |
| 430 |
when translating it. :-) |
| 431 |
|
| 432 |
Sun Jan 24 18:00 1999 Gerard Roudier ([email protected]) |
| 433 |
* version sym53c8xx-1.1 |
| 434 |
- Major rewrite of the SCSI parity error handling. |
| 435 |
The information contained in the data manuals is incomplete about |
| 436 |
this feature. |
| 437 |
I asked SYMBIOS about and got in reply the explanations that are |
| 438 |
_indeed_ missing in the data manuals. |
| 439 |
- Allow to tune request_irq() flags from the boot command line using |
| 440 |
ncr53c8xx=irqm:??, as follows: |
| 441 |
a) If bit 0x10 is set in irqm, SA_SHIRQ flag is not used. |
| 442 |
b) If bit 0x20 is set in irqm, SA_INTERRUPT flag is not used. |
| 443 |
By default the driver uses both SA_SHIRQ and SA_INTERRUPT. |
| 444 |
Option 'ncr53c8xx=irqm:0x20' may be used when an IRQ is shared by |
| 445 |
a 53C8XX adapter and a network board. |
| 446 |
- Fix for 64 bit PCI address register calculation. (Lance Robinson) |
| 447 |
- Fix for big-endian in phase mismatch handling. (Michal Jaegermann) |
| 448 |
|
| 449 |
Fri Jan 1 20:00 1999 Gerard Roudier ([email protected]) |
| 450 |
* version sym53c8xx-1.0a |
| 451 |
- Waiting list look-up didn't work for the first command of the list. |
| 452 |
Hopefully fixed, but tested on paper only. ;) |
| 453 |
- Remove the most part of PPC specific code for Linux-2.2. |
| 454 |
Thanks to Cort. |
| 455 |
- Some other minors changes. |
| 456 |
|
| 457 |
Sat Dec 19 21:00 1998 Gerard Roudier ([email protected]) |
| 458 |
* version sym53c8xx-1.0 |
| 459 |
- Define some new IO registers for the 896 (istat1, mbox0, mbox1) |
| 460 |
- Revamp slightly the Symbios NVRAM lay-out based on the excerpt of |
| 461 |
the header file I received from Symbios. |
| 462 |
- Check the PCI bus number for the boot order (Using a fast |
| 463 |
PCI controller behind a PCI-PCI bridge seems sub-optimal). |
| 464 |
- Disable overlapped PCI arbitration for the 896 revision 1. |
| 465 |
- Reduce a bit the number of IO register reads for phase mismatch |
| 466 |
by reading DWORDS at a time instead of BYTES. |
| 467 |
|
| 468 |
Thu Dec 3 24:00 1998 Gerard Roudier ([email protected]) |
| 469 |
* version pre-sym53c8xx-0.18 |
| 470 |
- I received this afternoon a 896 from SYMBIOS and started testing |
| 471 |
the driver with this beast. After having fixed 3 buglets, it worked |
| 472 |
with all features enabled including the phase mismatch handling |
| 473 |
from SCRIPTS. Since this feature is not yet tested enough, the |
| 474 |
boot option 'ncr53c8xx=specf:1' is still required to enable the |
| 475 |
driver to handle PM from SCRIPTS. |
| 476 |
|
| 477 |
Sun Nov 29 18:00 1998 Gerard Roudier ([email protected]) |
| 478 |
* version pre-sym53c8xx-0.17 |
| 479 |
- The SISL RAID change requires now remap_pci_mem() stuff to be |
| 480 |
compiled for __i386__ when normal IOs are used. |
| 481 |
- The PCI memory read from SCRIPTS that should ensure ordering |
| 482 |
was in fact misplaced. BTW, this may explain why broken PCI |
| 483 |
device drivers regarding ordering are working so well. ;-) |
| 484 |
- Rewrite ncr53c8xx_setup (boot command line options) since the |
| 485 |
binary code was a bit too bloated in my opinion. |
| 486 |
- Make the code simpler in the wakeup_done routine. |
| 487 |
|
| 488 |
Tue Nov 24 23:00 1998 Gerard Roudier ([email protected]) |
| 489 |
* version pre-sym53c8xx-0.16 |
| 490 |
- Add SCSI_NCR_OPTIMIZE_896_1 compile option and 'optim' boot option. |
| 491 |
When set, the driver unconditionally assumes that the interrupt |
| 492 |
handler is called for command completion, then clears INTF, scans |
| 493 |
the done queue and returns if some completed CCB is found. If no |
| 494 |
completed CCB are found, interrupt handling will proceed normally. |
| 495 |
With a 896 that handles MA from SCRIPTS, this can be a great win, |
| 496 |
since the driver will never performs PCI read transactions, but |
| 497 |
only PCI write transactions that may be posted. |
| 498 |
If the driver haven't to also raise the SIGP this would be perfect. |
| 499 |
Even with this penalty, I think that this will work great. |
| 500 |
Obviously this optimization makes sense only if the IRQ is not |
| 501 |
shared with another device. |
| 502 |
- Still a buglet in the tags initial settings that needed to be fixed. |
| 503 |
It was not possible to disable TGQ at system startup for devices |
| 504 |
that claim TGQ support. The driver used at least 2 for the queue |
| 505 |
depth but didn't keep track of user settings for tags depth lower |
| 506 |
than 2. |
| 507 |
|
| 508 |
Thu Nov 19 23:00 1998 Gerard Roudier ([email protected]) |
| 509 |
* version pre-sym53c8xx-0.15 |
| 510 |
- Add support for hardware LED control of the 896. |
| 511 |
- Ignore chips that are driven by SISL RAID (DAC 960). |
| 512 |
Change sent by Leonard Zubkoff and slightly reworked. |
| 513 |
- Prevent 810A rev 11 and 860 rev 1 from using cache line based |
| 514 |
transactions since those early chip revisions may use such on |
| 515 |
LOAD/STORE instructions (work-around). |
| 516 |
- Remove some useless and bloat code from the pci init stuff. |
| 517 |
- Do not use the readX()/writeX() kernel functions for __i386__, |
| 518 |
since they perform useless masking operations in order to deal |
| 519 |
with broken driver in 2.1.X kernel. |
| 520 |
|
| 521 |
Wed Nov 11 10:00 1998 Gerard Roudier ([email protected]) |
| 522 |
* version pre-sym53c8xx-0.14 |
| 523 |
- The driver was unhappy when configured with default_tags > MAX_TAGS |
| 524 |
Hopefully doubly-fixed. |
| 525 |
- Set PCI_PARITY in PCI_COMMAND register in not set (PCI fix-up). |
| 526 |
- Print out some message if phase mismatch is handled from SCRIPTS. |
| 527 |
|
| 528 |
Sun Nov 1 14H00 1998 Gerard Roudier ([email protected]) |
| 529 |
* version pre-sym53c8xx-0.13 |
| 530 |
- Some rewrite of the device detection code. This code had been |
| 531 |
patched too much and needed to be face-lifted a bit. |
| 532 |
Remove all platform dependent fix-ups that was not needed or |
| 533 |
conflicted with some other driver code as work-arounds. |
| 534 |
Reread the NVRAM before the calling of ncr_attach(). This spares |
| 535 |
stack space and so allows to handle more boards. |
| 536 |
Handle 64 bit base addresses under linux-2.0.X. |
| 537 |
Set MASTER bit in PCI COMMAND register if not set. |
| 538 |
|
| 539 |
Wed Oct 30 22H00 1998 Gerard Roudier ([email protected]) |
| 540 |
* version pre-sym53c8xx-0.12 |
| 541 |
- Damned! I just broke the driver for Alpha by leaving a stale |
| 542 |
instruction in the source code. Hopefully fixed. |
| 543 |
- Do not set PFEN when it is useless. Doing so we are sure that BOF |
| 544 |
will be active, since the manual appears to be very unclear on what |
| 545 |
feature is actually used by the chip when both PFEN and BOF are |
| 546 |
set. |
| 547 |
|
| 548 |
Sat Oct 24 16H00 1998 Gerard Roudier ([email protected]) |
| 549 |
* version pre-sym53c8xx-0.11 |
| 550 |
- LOAD/STORE instructions were miscompiled for register offsets |
| 551 |
beyond 0x7f. This broke accesses to 896' new registers. |
| 552 |
- Disable by default Phase Mismatch handling from SCRIPTS, since |
| 553 |
current 896 rev.1 seems not to operate safely with the driver |
| 554 |
when this feature is enabled (and above LOAD/STORE fix applied). |
| 555 |
I will change the default to 'enabled' when this problem will be |
| 556 |
solved. |
| 557 |
Using boot option 'ncr53c8xx=specf:1' enables this feature. |
| 558 |
- Implement a work-around (DEL 472 - ITEM 5) that should allow the |
| 559 |
driver to safely enable hardware phase mismatch with 896 rev. 1. |
| 560 |
|
| 561 |
Tue Oct 20 22H00 1998 Gerard Roudier ([email protected]) |
| 562 |
* version pre-sym53c8xx-0.10 |
| 563 |
- Add the 53c876 description to the chip table. This is only useful |
| 564 |
for printing the right name of the controller. |
| 565 |
- Add additional checking of INQUIRY data: |
| 566 |
Check INQUIRY data received length is at least 7. Byte 7 of |
| 567 |
inquiry data contains device features bits and the driver might |
| 568 |
be confused by garbage. Also check peripheral qualifier. |
| 569 |
- Use a 1,3,5,...MAXTAGS*2+1 tag numbering. Previous driver could |
| 570 |
use any tag number from 1 to 253 and some non conformant devices |
| 571 |
might have problems with large tag numbers. |
| 572 |
- Use NAME53C and NAME53C8XX for chip name prefix chip family name. |
| 573 |
Just give a try using "sym53c" and "sym53c8xx" instead of "ncr53c" |
| 574 |
and "ncr53c8xx". :-) |
| 575 |
|
| 576 |
Sun Oct 11 17H00 1998 Gerard Roudier ([email protected]) |
| 577 |
* version pre-sym53c8xx-0.9 |
| 578 |
- DEL-441 Item 2 work-around for the 53c876 rev <= 5 (0x15). |
| 579 |
- Break ncr_scatter() into 2 functions in order to guarantee best |
| 580 |
possible code optimization for the case we get a scatter list. |
| 581 |
- Add the code intended to support up to 1 tera-byte for 64 bit systems. |
| 582 |
It is probably too early, but I wanted to complete the thing. |
| 583 |
|
| 584 |
Sat Oct 3 14H00 1998 Gerard Roudier ([email protected]) |
| 585 |
* version pre-sym53c8xx-0.8 |
| 586 |
- Do some testing with io_mapped and fix what needed to be so. |
| 587 |
- Wait for SCSI selection to complete or time-out immediately after |
| 588 |
the chip won arbitration, since executing SCRIPTS while the SCSI |
| 589 |
core is performing SCSI selection breaks the selection procedure |
| 590 |
at least for some chip revisions. |
| 591 |
- Interrupt the SCRIPTS if a device does not go to MSG OUT phase after |
| 592 |
having been selected with ATN. Such a situation is not recoverable, |
| 593 |
better to fail when we are stuck. |