| 1 |
# SPDX-License-Identifier: GPL-2.0-only |
| 2 |
|
| 3 |
config SND_HDA |
| 4 |
tristate |
| 5 |
select SND_PCM |
| 6 |
select SND_VMASTER |
| 7 |
select SND_JACK |
| 8 |
select SND_HDA_CORE |
| 9 |
|
| 10 |
if SND_HDA |
| 11 |
|
| 12 |
config SND_HDA_HWDEP |
| 13 |
bool "Build hwdep interface for HD-audio driver" |
| 14 |
select SND_HWDEP |
| 15 |
help |
| 16 |
Say Y here to build a hwdep interface for HD-audio driver. |
| 17 |
This interface can be used for out-of-band communication |
| 18 |
with codecs for debugging purposes. |
| 19 |
|
| 20 |
config SND_HDA_RECONFIG |
| 21 |
bool "Allow dynamic codec reconfiguration" |
| 22 |
help |
| 23 |
Say Y here to enable the HD-audio codec re-configuration feature. |
| 24 |
It allows user to clear the whole codec configuration, change the |
| 25 |
codec setup, add extra verbs, and re-configure the codec dynamically. |
| 26 |
|
| 27 |
Note that this item alone doesn't provide the sysfs interface, but |
| 28 |
enables the feature just for the patch loader below. |
| 29 |
If you need the traditional sysfs entries for the manual interaction, |
| 30 |
turn on CONFIG_SND_HDA_HWDEP as well. |
| 31 |
|
| 32 |
config SND_HDA_INPUT_BEEP |
| 33 |
bool "Support digital beep via input layer" |
| 34 |
depends on INPUT=y || INPUT=SND_HDA |
| 35 |
help |
| 36 |
Say Y here to build a digital beep interface for HD-audio |
| 37 |
driver. This interface is used to generate digital beeps. |
| 38 |
|
| 39 |
config SND_HDA_INPUT_BEEP_MODE |
| 40 |
int "Digital beep registration mode (0=off, 1=on)" |
| 41 |
depends on SND_HDA_INPUT_BEEP=y |
| 42 |
default "1" |
| 43 |
range 0 1 |
| 44 |
help |
| 45 |
Set 0 to disable the digital beep interface for HD-audio by default. |
| 46 |
Set 1 to always enable the digital beep interface for HD-audio by |
| 47 |
default. |
| 48 |
|
| 49 |
config SND_HDA_PATCH_LOADER |
| 50 |
bool "Support initialization patch loading for HD-audio" |
| 51 |
select FW_LOADER |
| 52 |
select SND_HDA_RECONFIG |
| 53 |
help |
| 54 |
Say Y here to allow the HD-audio driver to load a pseudo |
| 55 |
firmware file ("patch") for overriding the BIOS setup at |
| 56 |
start up. The "patch" file can be specified via patch module |
| 57 |
option, such as patch=hda-init. |
| 58 |
|
| 59 |
config SND_HDA_POWER_SAVE_DEFAULT |
| 60 |
int "Default time-out for HD-audio power-save mode" |
| 61 |
depends on PM |
| 62 |
default 0 |
| 63 |
help |
| 64 |
The default time-out value in seconds for HD-audio automatic |
| 65 |
power-save mode. 0 means to disable the power-save mode. |
| 66 |
|
| 67 |
config SND_HDA_CTL_DEV_ID |
| 68 |
bool "Use the device identifier field for controls" |
| 69 |
depends on SND_HDA_INTEL |
| 70 |
help |
| 71 |
Say Y to use the device identifier field for (mixer) |
| 72 |
controls (old behaviour until this option is available). |
| 73 |
|
| 74 |
When enabled, the multiple HDA codecs may set the device |
| 75 |
field in control (mixer) element identifiers. The use |
| 76 |
of this field is not recommended and defined for mixer controls. |
| 77 |
|
| 78 |
The old behaviour (Y) is obsolete and will be removed. Consider |
| 79 |
to not enable this option. |
| 80 |
|
| 81 |
config SND_HDA_PREALLOC_SIZE |
| 82 |
int "Pre-allocated buffer size for HD-audio driver" |
| 83 |
range 0 32768 |
| 84 |
default 0 if SND_DMA_SGBUF |
| 85 |
default 64 if !SND_DMA_SGBUF |
| 86 |
help |
| 87 |
Specifies the default pre-allocated buffer-size in kB for the |
| 88 |
HD-audio driver. A larger buffer (e.g. 2048) is preferred |
| 89 |
for systems using PulseAudio. The default 64 is chosen just |
| 90 |
for compatibility reasons. |
| 91 |
On x86 systems, the default is zero as S/G allocation works |
| 92 |
and no preallocation is needed in most cases. |
| 93 |
|
| 94 |
Note that the pre-allocation size can be changed dynamically |
| 95 |
via a proc file (/proc/asound/card*/pcm*/sub*/prealloc), too. |
| 96 |
|
| 97 |
endif |