| 1 |
// SPDX-License-Identifier: GPL-2.0+ |
| 2 |
/* |
| 3 |
* Turris 1.x Device Tree Source |
| 4 |
* |
| 5 |
* Copyright 2013 - 2022 CZ.NIC z.s.p.o. (http://www.nic.cz/) |
| 6 |
* |
| 7 |
* Pinout, Schematics and Altium hardware design files are open source |
| 8 |
* and available at: https://docs.turris.cz/hw/turris-1x/turris-1x/ |
| 9 |
*/ |
| 10 |
|
| 11 |
#include <dt-bindings/gpio/gpio.h> |
| 12 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 13 |
#include <dt-bindings/leds/common.h> |
| 14 |
/include/ "fsl/p2020si-pre.dtsi" |
| 15 |
|
| 16 |
/ { |
| 17 |
model = "Turris 1.x"; |
| 18 |
compatible = "cznic,turris1x"; |
| 19 |
|
| 20 |
aliases { |
| 21 |
ethernet0 = &enet0; |
| 22 |
ethernet1 = &enet1; |
| 23 |
ethernet2 = &enet2; |
| 24 |
serial0 = &serial0; |
| 25 |
serial1 = &serial1; |
| 26 |
pci0 = &pci0; |
| 27 |
pci1 = &pci1; |
| 28 |
pci2 = &pci2; |
| 29 |
spi0 = &spi0; |
| 30 |
}; |
| 31 |
|
| 32 |
memory { |
| 33 |
device_type = "memory"; |
| 34 |
}; |
| 35 |
|
| 36 |
soc: soc@ffe00000 { |
| 37 |
ranges = <0x0 0x0 0xffe00000 0x00100000>; |
| 38 |
|
| 39 |
i2c@3000 { |
| 40 |
/* PCA9557PW GPIO controller for boot config */ |
| 41 |
gpio-controller@18 { |
| 42 |
compatible = "nxp,pca9557"; |
| 43 |
label = "bootcfg"; |
| 44 |
reg = <0x18>; |
| 45 |
#gpio-cells = <2>; |
| 46 |
gpio-controller; |
| 47 |
polarity = <0x00>; |
| 48 |
}; |
| 49 |
|
| 50 |
/* STM32F030R8T6 MCU for power control */ |
| 51 |
power-control@2a { |
| 52 |
/* |
| 53 |
* Turris Power Control firmware runs on STM32F0 MCU. |
| 54 |
* This firmware is open source and available at: |
| 55 |
* https://gitlab.nic.cz/turris/hw/turris_power_control |
| 56 |
*/ |
| 57 |
reg = <0x2a>; |
| 58 |
}; |
| 59 |
|
| 60 |
/* DDR3 SPD/EEPROM PSWP instruction */ |
| 61 |
eeprom@32 { |
| 62 |
reg = <0x32>; |
| 63 |
}; |
| 64 |
|
| 65 |
/* SA56004ED temperature control */ |
| 66 |
temperature-sensor@4c { |
| 67 |
compatible = "nxp,sa56004"; |
| 68 |
reg = <0x4c>; |
| 69 |
interrupt-parent = <&gpio>; |
| 70 |
interrupts = <12 IRQ_TYPE_LEVEL_LOW>, /* GPIO12 - ALERT pin */ |
| 71 |
<13 IRQ_TYPE_LEVEL_LOW>; /* GPIO13 - CRIT pin */ |
| 72 |
#address-cells = <1>; |
| 73 |
#size-cells = <0>; |
| 74 |
|
| 75 |
/* Local temperature sensor (SA56004ED internal) */ |
| 76 |
channel@0 { |
| 77 |
reg = <0>; |
| 78 |
label = "board"; |
| 79 |
}; |
| 80 |
|
| 81 |
/* Remote temperature sensor (D+/D- connected to P2020 CPU Temperature Diode) */ |
| 82 |
channel@1 { |
| 83 |
reg = <1>; |
| 84 |
label = "cpu"; |
| 85 |
}; |
| 86 |
}; |
| 87 |
|
| 88 |
/* DDR3 SPD/EEPROM */ |
| 89 |
eeprom@52 { |
| 90 |
compatible = "atmel,spd"; |
| 91 |
reg = <0x52>; |
| 92 |
}; |
| 93 |
|
| 94 |
/* MCP79402-I/ST Protected EEPROM */ |
| 95 |
eeprom@57 { |
| 96 |
reg = <0x57>; |
| 97 |
}; |
| 98 |
|
| 99 |
/* ATSHA204-TH-DA-T crypto module */ |
| 100 |
crypto@64 { |
| 101 |
compatible = "atmel,atsha204"; |
| 102 |
reg = <0x64>; |
| 103 |
}; |
| 104 |
|
| 105 |
/* IDT6V49205BNLGI clock generator */ |
| 106 |
clock-generator@69 { |
| 107 |
compatible = "idt,6v49205b"; |
| 108 |
reg = <0x69>; |
| 109 |
}; |
| 110 |
|
| 111 |
/* MCP79402-I/ST RTC */ |
| 112 |
rtc@6f { |
| 113 |
compatible = "microchip,mcp7940x"; |
| 114 |
reg = <0x6f>; |
| 115 |
interrupt-parent = <&gpio>; |
| 116 |
interrupts = <14 0>; /* GPIO14 - MFP pin */ |
| 117 |
}; |
| 118 |
}; |
| 119 |
|
| 120 |
/* SPI on connector P1 */ |
| 121 |
spi0: spi@7000 { |
| 122 |
}; |
| 123 |
|
| 124 |
gpio: gpio-controller@fc00 { |
| 125 |
#interrupt-cells = <2>; |
| 126 |
interrupt-controller; |
| 127 |
}; |
| 128 |
|
| 129 |
/* Connected to SMSC USB2412-DZK 2-Port USB 2.0 Hub Controller */ |
| 130 |
usb@22000 { |
| 131 |
phy_type = "ulpi"; |
| 132 |
dr_mode = "host"; |
| 133 |
}; |
| 134 |
|
| 135 |
enet0: ethernet@24000 { |
| 136 |
/* Connected to port 6 of QCA8337N-AL3C switch */ |
| 137 |
phy-connection-type = "rgmii-id"; |
| 138 |
|
| 139 |
fixed-link { |
| 140 |
speed = <1000>; |
| 141 |
full-duplex; |
| 142 |
}; |
| 143 |
}; |
| 144 |
|
| 145 |
mdio@24520 { |
| 146 |
/* KSZ9031RNXCA ethernet phy for WAN port */ |
| 147 |
phy: ethernet-phy@7 { |
| 148 |
interrupts = <3 1 0 0>; |
| 149 |
reg = <0x7>; |
| 150 |
}; |
| 151 |
|
| 152 |
/* QCA8337N-AL3C switch with integrated ethernet PHYs for LAN ports */ |
| 153 |
switch@10 { |
| 154 |
compatible = "qca,qca8337"; |
| 155 |
interrupts = <2 1 0 0>; |
| 156 |
reg = <0x10>; |
| 157 |
|
| 158 |
ports { |
| 159 |
#address-cells = <1>; |
| 160 |
#size-cells = <0>; |
| 161 |
|
| 162 |
port@0 { |
| 163 |
reg = <0>; |
| 164 |
label = "cpu"; |
| 165 |
ethernet = <&enet1>; |
| 166 |
phy-mode = "rgmii-id"; |
| 167 |
|
| 168 |
fixed-link { |
| 169 |
speed = <1000>; |
| 170 |
full-duplex; |
| 171 |
}; |
| 172 |
}; |
| 173 |
|
| 174 |
port@1 { |
| 175 |
reg = <1>; |
| 176 |
label = "lan5"; |
| 177 |
}; |
| 178 |
|
| 179 |
port@2 { |
| 180 |
reg = <2>; |
| 181 |
label = "lan4"; |
| 182 |
}; |
| 183 |
|
| 184 |
port@3 { |
| 185 |
reg = <3>; |
| 186 |
label = "lan3"; |
| 187 |
}; |
| 188 |
|
| 189 |
port@4 { |
| 190 |
reg = <4>; |
| 191 |
label = "lan2"; |
| 192 |
}; |
| 193 |
|
| 194 |
port@5 { |
| 195 |
reg = <5>; |
| 196 |
label = "lan1"; |
| 197 |
}; |
| 198 |
|
| 199 |
port@6 { |
| 200 |
reg = <6>; |
| 201 |
label = "cpu"; |
| 202 |
ethernet = <&enet0>; |
| 203 |
phy-mode = "rgmii-id"; |
| 204 |
|
| 205 |
fixed-link { |
| 206 |
speed = <1000>; |
| 207 |
full-duplex; |
| 208 |
}; |
| 209 |
}; |
| 210 |
}; |
| 211 |
}; |
| 212 |
}; |
| 213 |
|
| 214 |
ptp_clock@24e00 { |
| 215 |
fsl,tclk-period = <5>; |
| 216 |
fsl,tmr-prsc = <200>; |
| 217 |
fsl,tmr-add = <0xcccccccd>; |
| 218 |
fsl,tmr-fiper1 = <0x3b9ac9fb>; |
| 219 |
fsl,tmr-fiper2 = <0x0001869b>; |
| 220 |
fsl,max-adj = <249999999>; |
| 221 |
}; |
| 222 |
|
| 223 |
enet1: ethernet@25000 { |
| 224 |
/* Connected to port 0 of QCA8337N-AL3C switch */ |
| 225 |
phy-connection-type = "rgmii-id"; |
| 226 |
|
| 227 |
fixed-link { |
| 228 |
speed = <1000>; |
| 229 |
full-duplex; |
| 230 |
}; |
| 231 |
}; |
| 232 |
|
| 233 |
mdio@25520 { |
| 234 |
status = "disabled"; |
| 235 |
}; |
| 236 |
|
| 237 |
enet2: ethernet@26000 { |
| 238 |
/* Connected to KSZ9031RNXCA ethernet phy (WAN port) */ |
| 239 |
label = "wan"; |
| 240 |
phy-handle = <&phy>; |
| 241 |
phy-connection-type = "rgmii-id"; |
| 242 |
}; |
| 243 |
|
| 244 |
mdio@26520 { |
| 245 |
status = "disabled"; |
| 246 |
}; |
| 247 |
|
| 248 |
sdhc@2e000 { |
| 249 |
bus-width = <4>; |
| 250 |
cd-gpios = <&gpio 8 GPIO_ACTIVE_LOW>; |
| 251 |
}; |
| 252 |
}; |
| 253 |
|
| 254 |
lbc: localbus@ffe05000 { |
| 255 |
reg = <0 0xffe05000 0 0x1000>; |
| 256 |
|
| 257 |
ranges = <0x0 0x0 0x0 0xef000000 0x01000000>, /* NOR */ |
| 258 |
<0x1 0x0 0x0 0xff800000 0x00040000>, /* NAND */ |
| 259 |
<0x3 0x0 0x0 0xffa00000 0x00020000>; /* CPLD */ |
| 260 |
|
| 261 |
/* S29GL128P90TFIR10 NOR */ |
| 262 |
nor@0,0 { |
| 263 |
compatible = "cfi-flash"; |
| 264 |
reg = <0x0 0x0 0x01000000>; |
| 265 |
bank-width = <2>; |
| 266 |
device-width = <1>; |
| 267 |
|
| 268 |
partitions { |
| 269 |
compatible = "fixed-partitions"; |
| 270 |
#address-cells = <1>; |
| 271 |
#size-cells = <1>; |
| 272 |
|
| 273 |
partition@0 { |
| 274 |
/* 128 kB for Device Tree Blob */ |
| 275 |
reg = <0x00000000 0x00020000>; |
| 276 |
label = "dtb"; |
| 277 |
}; |
| 278 |
|
| 279 |
partition@20000 { |
| 280 |
/* 1.7 MB for Linux Kernel Image */ |
| 281 |
reg = <0x00020000 0x001a0000>; |
| 282 |
label = "kernel"; |
| 283 |
}; |
| 284 |
|
| 285 |
partition@1c0000 { |
| 286 |
/* 1.5 MB for Rescue JFFS2 Root File System */ |
| 287 |
reg = <0x001c0000 0x00180000>; |
| 288 |
label = "rescue"; |
| 289 |
}; |
| 290 |
|
| 291 |
partition@340000 { |
| 292 |
/* 11 MB for TAR.XZ Archive with Factory content of NAND Root File System */ |
| 293 |
reg = <0x00340000 0x00b00000>; |
| 294 |
label = "factory"; |
| 295 |
}; |
| 296 |
|
| 297 |
partition@e40000 { |
| 298 |
/* 768 kB for Certificates JFFS2 File System */ |
| 299 |
reg = <0x00e40000 0x000c0000>; |
| 300 |
label = "certificates"; |
| 301 |
}; |
| 302 |
|
| 303 |
/* free unused space 0x00f00000-0x00f20000 */ |
| 304 |
|
| 305 |
partition@f20000 { |
| 306 |
/* 128 kB for U-Boot Environment Variables */ |
| 307 |
reg = <0x00f20000 0x00020000>; |
| 308 |
label = "u-boot-env"; |
| 309 |
}; |
| 310 |
|
| 311 |
partition@f40000 { |
| 312 |
/* 768 kB for U-Boot Bootloader Image */ |
| 313 |
reg = <0x00f40000 0x000c0000>; |
| 314 |
label = "u-boot"; |
| 315 |
}; |
| 316 |
}; |
| 317 |
}; |
| 318 |
|
| 319 |
/* MT29F2G08ABAEAWP:E NAND */ |
| 320 |
nand@1,0 { |
| 321 |
compatible = "fsl,p2020-fcm-nand", "fsl,elbc-fcm-nand"; |
| 322 |
reg = <0x1 0x0 0x00040000>; |
| 323 |
nand-ecc-mode = "soft"; |
| 324 |
nand-ecc-algo = "bch"; |
| 325 |
|
| 326 |
partitions { |
| 327 |
compatible = "fixed-partitions"; |
| 328 |
#address-cells = <1>; |
| 329 |
#size-cells = <1>; |
| 330 |
|
| 331 |
partition@0 { |
| 332 |
/* 256 MB for UBI with one volume: UBIFS Root File System */ |
| 333 |
reg = <0x00000000 0x10000000>; |
| 334 |
label = "rootfs"; |
| 335 |
}; |
| 336 |
}; |
| 337 |
}; |
| 338 |
|
| 339 |
/* LCMXO1200C-3FTN256C FPGA */ |
| 340 |
cpld@3,0 { |
| 341 |
/* |
| 342 |
* Turris CPLD firmware which runs on this Lattice FPGA, |
| 343 |
* is extended version of P1021RDB-PC CPLD v4.1 firmware. |
| 344 |
* It is backward compatible with its original version |
| 345 |
* and the only extension is support for Turris LEDs. |
| 346 |
* Turris CPLD firmware is open source and available at: |
| 347 |
* https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPLD.v |
| 348 |
*/ |
| 349 |
compatible = "cznic,turris1x-cpld", "fsl,p1021rdb-pc-cpld", "simple-bus", "syscon"; |
| 350 |
reg = <0x3 0x0 0x30>; |
| 351 |
#address-cells = <1>; |
| 352 |
#size-cells = <1>; |
| 353 |
ranges = <0x0 0x3 0x0 0x00020000>; |
| 354 |
|
| 355 |
/* MAX6370KA+T watchdog */ |
| 356 |
watchdog@2 { |
| 357 |
/* |
| 358 |
* CPLD firmware maps SET0, SET1 and SET2 |
| 359 |
* input logic of MAX6370KA+T chip to CPLD |
| 360 |
* memory space at byte offset 0x2. WDI |
| 361 |
* input logic is outside of the CPLD and |
| 362 |
* connected via external GPIO. |
| 363 |
*/ |
| 364 |
compatible = "maxim,max6370"; |
| 365 |
reg = <0x02 0x01>; |
| 366 |
gpios = <&gpio 11 GPIO_ACTIVE_LOW>; |
| 367 |
}; |
| 368 |
|
| 369 |
reboot@d { |
| 370 |
/* |
| 371 |
* CPLD firmware which manages system reset and |
| 372 |
* watchdog registers has bugs. It does not |
| 373 |
* autoclear system reset register after change |
| 374 |
* and watchdog ignores reset line on immediate |
| 375 |
* succeeding reset cycle triggered by watchdog. |
| 376 |
* These bugs have to be workarounded in U-Boot |
| 377 |
* bootloader. So use system reset via syscon as |
| 378 |
* a last resort because older U-Boot versions |
| 379 |
* do not have workaround for watchdog. |
| 380 |
* |
| 381 |
* Reset method via rstcr's global-utilities |
| 382 |
* (the preferred one) has priority level 128, |
| 383 |
* watchdog has priority level 0 and default |
| 384 |
* syscon-reboot priority level is 192. |
| 385 |
* |
| 386 |
* So define syscon-reboot with custom priority |
| 387 |
* level 64 (between rstcr and watchdog) because |
| 388 |
* rstcr should stay as default preferred reset |
| 389 |
* method and reset via watchdog is more broken |
| 390 |
* than system reset via syscon. |
| 391 |
*/ |
| 392 |
compatible = "syscon-reboot"; |
| 393 |
reg = <0x0d 0x01>; |
| 394 |
offset = <0x0d>; |
| 395 |
mask = <0x01>; |
| 396 |
value = <0x01>; |
| 397 |
priority = <64>; |
| 398 |
}; |
| 399 |
|
| 400 |
led-controller@13 { |
| 401 |
/* |
| 402 |
* LEDs are controlled by CPLD firmware. |
| 403 |
* All five LAN LEDs share common RGB settings |
| 404 |
* and so it is not possible to set different |
| 405 |
* colors on different LAN ports. |
| 406 |
*/ |
| 407 |
compatible = "cznic,turris1x-leds"; |
| 408 |
reg = <0x13 0x1d>; |
| 409 |
#address-cells = <1>; |
| 410 |
#size-cells = <0>; |
| 411 |
|
| 412 |
multi-led@0 { |
| 413 |
reg = <0x0>; |
| 414 |
color = <LED_COLOR_ID_RGB>; |
| 415 |
function = LED_FUNCTION_WAN; |
| 416 |
}; |
| 417 |
|
| 418 |
multi-led@1 { |
| 419 |
reg = <0x1>; |
| 420 |
color = <LED_COLOR_ID_RGB>; |
| 421 |
function = LED_FUNCTION_LAN; |
| 422 |
function-enumerator = <5>; |
| 423 |
}; |
| 424 |
|
| 425 |
multi-led@2 { |
| 426 |
reg = <0x2>; |
| 427 |
color = <LED_COLOR_ID_RGB>; |
| 428 |
function = LED_FUNCTION_LAN; |
| 429 |
function-enumerator = <4>; |
| 430 |
}; |
| 431 |
|
| 432 |
multi-led@3 { |
| 433 |
reg = <0x3>; |
| 434 |
color = <LED_COLOR_ID_RGB>; |
| 435 |
function = LED_FUNCTION_LAN; |
| 436 |
function-enumerator = <3>; |
| 437 |
}; |
| 438 |
|
| 439 |
multi-led@4 { |
| 440 |
reg = <0x4>; |
| 441 |
color = <LED_COLOR_ID_RGB>; |
| 442 |
function = LED_FUNCTION_LAN; |
| 443 |
function-enumerator = <2>; |
| 444 |
}; |
| 445 |
|
| 446 |
multi-led@5 { |
| 447 |
reg = <0x5>; |
| 448 |
color = <LED_COLOR_ID_RGB>; |
| 449 |
function = LED_FUNCTION_LAN; |
| 450 |
function-enumerator = <1>; |
| 451 |
}; |
| 452 |
|
| 453 |
multi-led@6 { |
| 454 |
reg = <0x6>; |
| 455 |
color = <LED_COLOR_ID_RGB>; |
| 456 |
function = LED_FUNCTION_WLAN; |
| 457 |
}; |
| 458 |
|
| 459 |
multi-led@7 { |
| 460 |
reg = <0x7>; |
| 461 |
color = <LED_COLOR_ID_RGB>; |
| 462 |
function = LED_FUNCTION_POWER; |
| 463 |
}; |
| 464 |
}; |
| 465 |
}; |
| 466 |
}; |
| 467 |
|
| 468 |
pci2: pcie@ffe08000 { |
| 469 |
/* |
| 470 |
* PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller. |
| 471 |
* This xHCI controller is available only on Turris 1.1 boards. |
| 472 |
* Turris 1.0 boards have nothing connected to this PCIe bus, |
| 473 |
* so system would see only PCIe Root Port of this PCIe Root |
| 474 |
* Complex. TUSB7340RKM xHCI controller has four SuperSpeed |
| 475 |
* channels. Channel 0 is connected to the front USB 3.0 port, |
| 476 |
* channel 1 (but only USB 2.0 subset) to USB 2.0 pins on mPCIe |
| 477 |
* slot 1 (CN5), channels 2 and 3 to connector P600. |
| 478 |
* |
| 479 |
* P2020 PCIe Root Port does not use PCIe MEM and xHCI controller |
| 480 |
* uses 64kB + 8kB of PCIe MEM. No PCIe IO is used or required. |
| 481 |
* So allocate 128kB of PCIe MEM for this PCIe bus. |
| 482 |
*/ |
| 483 |
reg = <0 0xffe08000 0 0x1000>; |
| 484 |
ranges = <0x02000000 0x0 0xc0000000 0 0xc0000000 0x0 0x00020000>, /* MEM */ |
| 485 |
<0x01000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>; /* IO */ |
| 486 |
|
| 487 |
pcie@0 { |
| 488 |
ranges; |
| 489 |
}; |
| 490 |
}; |
| 491 |
|
| 492 |
pci1: pcie@ffe09000 { |
| 493 |
/* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */ |
| 494 |
reg = <0 0xffe09000 0 0x1000>; |
| 495 |
ranges = <0x02000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000>, /* MEM */ |
| 496 |
<0x01000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>; /* IO */ |
| 497 |
|
| 498 |
pcie@0 { |
| 499 |
ranges; |
| 500 |
}; |
| 501 |
}; |
| 502 |
|
| 503 |
pci0: pcie@ffe0a000 { |
| 504 |
/* |
| 505 |
* PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card. |
| 506 |
* Turris 1.1 boards have in this mPCIe slot additional USB 2.0 |
| 507 |
* pins via channel 1 of TUSB7340RKM xHCI controller and also |
| 508 |
* additional SIM card slot, both for USB-based WWAN cards. |
| 509 |
*/ |
| 510 |
reg = <0 0xffe0a000 0 0x1000>; |
| 511 |
ranges = <0x02000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000>, /* MEM */ |
| 512 |
<0x01000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>; /* IO */ |
| 513 |
|
| 514 |
pcie@0 { |
| 515 |
ranges; |
| 516 |
}; |
| 517 |
}; |
| 518 |
}; |
| 519 |
|
| 520 |
/include/ "fsl/p2020si-post.dtsi" |