| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* phyCORE-MPC5200B-IO (pcm032) board Device Tree Source |
| 4 |
* |
| 5 |
* Copyright (C) 2006-2009 Pengutronix |
| 6 |
* Sascha Hauer, Juergen Beisert, Wolfram Sang <[email protected]> |
| 7 |
*/ |
| 8 |
|
| 9 |
/include/ "mpc5200b.dtsi" |
| 10 |
|
| 11 |
&gpt0 { fsl,has-wdt; }; |
| 12 |
&gpt2 { gpio-controller; }; |
| 13 |
&gpt3 { gpio-controller; }; |
| 14 |
&gpt4 { gpio-controller; }; |
| 15 |
&gpt5 { gpio-controller; }; |
| 16 |
&gpt6 { gpio-controller; }; |
| 17 |
&gpt7 { gpio-controller; }; |
| 18 |
|
| 19 |
/ { |
| 20 |
model = "phytec,pcm032"; |
| 21 |
compatible = "phytec,pcm032"; |
| 22 |
|
| 23 |
memory@0 { |
| 24 |
reg = <0x00000000 0x08000000>; // 128MB |
| 25 |
}; |
| 26 |
|
| 27 |
soc5200@f0000000 { |
| 28 |
psc@2000 { /* PSC1 is ac97 */ |
| 29 |
compatible = "fsl,mpc5200b-psc-ac97","fsl,mpc5200-psc-ac97"; |
| 30 |
cell-index = <0>; |
| 31 |
}; |
| 32 |
|
| 33 |
/* PSC2 port is used by CAN1/2 */ |
| 34 |
psc@2200 { |
| 35 |
status = "disabled"; |
| 36 |
}; |
| 37 |
|
| 38 |
psc@2400 { /* PSC3 in UART mode */ |
| 39 |
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; |
| 40 |
}; |
| 41 |
|
| 42 |
/* PSC4 is ??? */ |
| 43 |
psc@2600 { |
| 44 |
status = "disabled"; |
| 45 |
}; |
| 46 |
|
| 47 |
/* PSC5 is ??? */ |
| 48 |
psc@2800 { |
| 49 |
status = "disabled"; |
| 50 |
}; |
| 51 |
|
| 52 |
psc@2c00 { /* PSC6 in UART mode */ |
| 53 |
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; |
| 54 |
}; |
| 55 |
|
| 56 |
ethernet@3000 { |
| 57 |
phy-handle = <&phy0>; |
| 58 |
}; |
| 59 |
|
| 60 |
mdio@3000 { |
| 61 |
phy0: ethernet-phy@0 { |
| 62 |
reg = <0>; |
| 63 |
}; |
| 64 |
}; |
| 65 |
|
| 66 |
i2c@3d40 { |
| 67 |
rtc@51 { |
| 68 |
compatible = "nxp,pcf8563"; |
| 69 |
reg = <0x51>; |
| 70 |
}; |
| 71 |
eeprom@52 { |
| 72 |
compatible = "catalyst,24c32", "atmel,24c32"; |
| 73 |
reg = <0x52>; |
| 74 |
pagesize = <32>; |
| 75 |
}; |
| 76 |
}; |
| 77 |
}; |
| 78 |
|
| 79 |
pci@f0000d00 { |
| 80 |
interrupt-map-mask = <0xf800 0 0 7>; |
| 81 |
interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot |
| 82 |
0xc000 0 0 2 &mpc5200_pic 1 1 3 |
| 83 |
0xc000 0 0 3 &mpc5200_pic 1 2 3 |
| 84 |
0xc000 0 0 4 &mpc5200_pic 1 3 3 |
| 85 |
|
| 86 |
0xc800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot |
| 87 |
0xc800 0 0 2 &mpc5200_pic 1 2 3 |
| 88 |
0xc800 0 0 3 &mpc5200_pic 1 3 3 |
| 89 |
0xc800 0 0 4 &mpc5200_pic 0 0 3>; |
| 90 |
ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000>, |
| 91 |
<0x02000000 0 0xa0000000 0xa0000000 0 0x10000000>, |
| 92 |
<0x01000000 0 0x00000000 0xb0000000 0 0x01000000>; |
| 93 |
}; |
| 94 |
|
| 95 |
localbus { |
| 96 |
ranges = <0 0 0xfe000000 0x02000000 |
| 97 |
1 0 0xfc000000 0x02000000 |
| 98 |
2 0 0xfbe00000 0x00200000 |
| 99 |
3 0 0xf9e00000 0x02000000 |
| 100 |
4 0 0xf7e00000 0x02000000 |
| 101 |
5 0 0xe6000000 0x02000000 |
| 102 |
6 0 0xe8000000 0x02000000 |
| 103 |
7 0 0xea000000 0x02000000>; |
| 104 |
|
| 105 |
flash@0,0 { |
| 106 |
compatible = "cfi-flash"; |
| 107 |
reg = <0 0 0x02000000>; |
| 108 |
bank-width = <4>; |
| 109 |
#size-cells = <1>; |
| 110 |
#address-cells = <1>; |
| 111 |
|
| 112 |
partition@0 { |
| 113 |
label = "ubootl"; |
| 114 |
reg = <0x00000000 0x00040000>; |
| 115 |
}; |
| 116 |
partition@40000 { |
| 117 |
label = "kernel"; |
| 118 |
reg = <0x00040000 0x001c0000>; |
| 119 |
}; |
| 120 |
partition@200000 { |
| 121 |
label = "jffs2"; |
| 122 |
reg = <0x00200000 0x01d00000>; |
| 123 |
}; |
| 124 |
partition@1f00000 { |
| 125 |
label = "uboot"; |
| 126 |
reg = <0x01f00000 0x00040000>; |
| 127 |
}; |
| 128 |
partition@1f40000 { |
| 129 |
label = "env"; |
| 130 |
reg = <0x01f40000 0x00040000>; |
| 131 |
}; |
| 132 |
partition@1f80000 { |
| 133 |
label = "oftree"; |
| 134 |
reg = <0x01f80000 0x00040000>; |
| 135 |
}; |
| 136 |
partition@1fc0000 { |
| 137 |
label = "space"; |
| 138 |
reg = <0x01fc0000 0x00040000>; |
| 139 |
}; |
| 140 |
}; |
| 141 |
|
| 142 |
sram@2,0 { |
| 143 |
compatible = "mtd-ram"; |
| 144 |
reg = <2 0 0x00200000>; |
| 145 |
bank-width = <2>; |
| 146 |
}; |
| 147 |
|
| 148 |
/* |
| 149 |
* example snippets for FPGA |
| 150 |
* |
| 151 |
* fpga@3,0 { |
| 152 |
* compatible = "fpga_driver"; |
| 153 |
* reg = <3 0 0x02000000>; |
| 154 |
* bank-width = <4>; |
| 155 |
* }; |
| 156 |
* |
| 157 |
* fpga@4,0 { |
| 158 |
* compatible = "fpga_driver"; |
| 159 |
* reg = <4 0 0x02000000>; |
| 160 |
* bank-width = <4>; |
| 161 |
* }; |
| 162 |
*/ |
| 163 |
|
| 164 |
/* |
| 165 |
* example snippets for free chipselects |
| 166 |
* |
| 167 |
* device@5,0 { |
| 168 |
* compatible = "custom_driver"; |
| 169 |
* reg = <5 0 0x02000000>; |
| 170 |
* }; |
| 171 |
* |
| 172 |
* device@6,0 { |
| 173 |
* compatible = "custom_driver"; |
| 174 |
* reg = <6 0 0x02000000>; |
| 175 |
* }; |
| 176 |
* |
| 177 |
* device@7,0 { |
| 178 |
* compatible = "custom_driver"; |
| 179 |
* reg = <7 0 0x02000000>; |
| 180 |
* }; |
| 181 |
*/ |
| 182 |
}; |
| 183 |
}; |