| 1 |
/* |
| 2 |
* Device Tree Source for IBM Embedded PPC 476 Platform |
| 3 |
* |
| 4 |
* Copyright © 2011 Tony Breeds IBM Corporation |
| 5 |
* |
| 6 |
* This file is licensed under the terms of the GNU General Public |
| 7 |
* License version 2. This program is licensed "as is" without |
| 8 |
* any warranty of any kind, whether express or implied. |
| 9 |
*/ |
| 10 |
|
| 11 |
/dts-v1/; |
| 12 |
|
| 13 |
/memreserve/ 0x01f00000 0x00100000; // spin table |
| 14 |
|
| 15 |
/ { |
| 16 |
#address-cells = <2>; |
| 17 |
#size-cells = <2>; |
| 18 |
model = "ibm,currituck"; |
| 19 |
compatible = "ibm,currituck"; |
| 20 |
dcr-parent = <&{/cpus/cpu@0}>; |
| 21 |
|
| 22 |
aliases { |
| 23 |
serial0 = &UART0; |
| 24 |
}; |
| 25 |
|
| 26 |
cpus { |
| 27 |
#address-cells = <1>; |
| 28 |
#size-cells = <0>; |
| 29 |
|
| 30 |
cpu@0 { |
| 31 |
device_type = "cpu"; |
| 32 |
model = "PowerPC,476"; |
| 33 |
reg = <0>; |
| 34 |
clock-frequency = <1600000000>; // 1.6 GHz |
| 35 |
timebase-frequency = <100000000>; // 100Mhz |
| 36 |
i-cache-line-size = <32>; |
| 37 |
d-cache-line-size = <32>; |
| 38 |
i-cache-size = <32768>; |
| 39 |
d-cache-size = <32768>; |
| 40 |
dcr-controller; |
| 41 |
dcr-access-method = "native"; |
| 42 |
status = "okay"; |
| 43 |
}; |
| 44 |
cpu@1 { |
| 45 |
device_type = "cpu"; |
| 46 |
model = "PowerPC,476"; |
| 47 |
reg = <1>; |
| 48 |
clock-frequency = <1600000000>; // 1.6 GHz |
| 49 |
timebase-frequency = <100000000>; // 100Mhz |
| 50 |
i-cache-line-size = <32>; |
| 51 |
d-cache-line-size = <32>; |
| 52 |
i-cache-size = <32768>; |
| 53 |
d-cache-size = <32768>; |
| 54 |
dcr-controller; |
| 55 |
dcr-access-method = "native"; |
| 56 |
status = "disabled"; |
| 57 |
enable-method = "spin-table"; |
| 58 |
cpu-release-addr = <0x0 0x01f00000>; |
| 59 |
}; |
| 60 |
}; |
| 61 |
|
| 62 |
memory { |
| 63 |
device_type = "memory"; |
| 64 |
reg = <0x0 0x0 0x0 0x0>; // filled in by zImage |
| 65 |
}; |
| 66 |
|
| 67 |
MPIC: interrupt-controller { |
| 68 |
compatible = "chrp,open-pic"; |
| 69 |
interrupt-controller; |
| 70 |
dcr-reg = <0xffc00000 0x00040000>; |
| 71 |
#address-cells = <0>; |
| 72 |
#size-cells = <0>; |
| 73 |
#interrupt-cells = <2>; |
| 74 |
|
| 75 |
}; |
| 76 |
|
| 77 |
plb { |
| 78 |
compatible = "ibm,plb6"; |
| 79 |
#address-cells = <2>; |
| 80 |
#size-cells = <2>; |
| 81 |
ranges; |
| 82 |
clock-frequency = <200000000>; // 200Mhz |
| 83 |
|
| 84 |
POB0: opb { |
| 85 |
compatible = "ibm,opb-4xx", "ibm,opb"; |
| 86 |
#address-cells = <1>; |
| 87 |
#size-cells = <1>; |
| 88 |
/* Wish there was a nicer way of specifying a full |
| 89 |
* 32-bit range |
| 90 |
*/ |
| 91 |
ranges = <0x00000000 0x00000200 0x00000000 0x80000000 |
| 92 |
0x80000000 0x00000200 0x80000000 0x80000000>; |
| 93 |
clock-frequency = <100000000>; |
| 94 |
|
| 95 |
UART0: serial@10000000 { |
| 96 |
device_type = "serial"; |
| 97 |
compatible = "ns16750", "ns16550"; |
| 98 |
reg = <0x10000000 0x00000008>; |
| 99 |
virtual-reg = <0xe1000000>; |
| 100 |
clock-frequency = <1851851>; // PCIe refclk/MCGC0_CTL[UART] |
| 101 |
current-speed = <115200>; |
| 102 |
interrupt-parent = <&MPIC>; |
| 103 |
interrupts = <34 2>; |
| 104 |
}; |
| 105 |
|
| 106 |
FPGA0: fpga@50000000 { |
| 107 |
compatible = "ibm,currituck-fpga"; |
| 108 |
reg = <0x50000000 0x4>; |
| 109 |
}; |
| 110 |
|
| 111 |
IIC0: i2c@0 { |
| 112 |
compatible = "ibm,iic-currituck", "ibm,iic"; |
| 113 |
reg = <0x0 0x00000014>; |
| 114 |
interrupt-parent = <&MPIC>; |
| 115 |
interrupts = <79 2>; |
| 116 |
#address-cells = <1>; |
| 117 |
#size-cells = <0>; |
| 118 |
rtc@68 { |
| 119 |
compatible = "st,m41t80", "m41st85"; |
| 120 |
reg = <0x68>; |
| 121 |
}; |
| 122 |
}; |
| 123 |
}; |
| 124 |
|
| 125 |
PCIE0: pcie@10100000000 { // 4xGBIF1 |
| 126 |
device_type = "pci"; |
| 127 |
#interrupt-cells = <1>; |
| 128 |
#size-cells = <2>; |
| 129 |
#address-cells = <3>; |
| 130 |
compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex"; |
| 131 |
primary; |
| 132 |
port = <0x0>; /* port number */ |
| 133 |
reg = <0x00000101 0x00000000 0x0 0x10000000 /* Config space access */ |
| 134 |
0x00000100 0x00000000 0x0 0x00001000>; /* UTL Registers space access */ |
| 135 |
dcr-reg = <0x80 0x20>; |
| 136 |
|
| 137 |
// pci_space < pci_addr > < cpu_addr > < size > |
| 138 |
ranges = <0x02000000 0x00000000 0x80000000 0x00000110 0x80000000 0x0 0x80000000 |
| 139 |
0x01000000 0x0 0x0 0x00000140 0x0 0x0 0x00010000>; |
| 140 |
|
| 141 |
/* Inbound starting at 0 to memsize filled in by zImage */ |
| 142 |
dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x0>; |
| 143 |
|
| 144 |
/* This drives busses 0 to 0xf */ |
| 145 |
bus-range = <0x0 0xf>; |
| 146 |
|
| 147 |
/* Legacy interrupts (note the weird polarity, the bridge seems |
| 148 |
* to invert PCIe legacy interrupts). |
| 149 |
* We are de-swizzling here because the numbers are actually for |
| 150 |
* port of the root complex virtual P2P bridge. But I want |
| 151 |
* to avoid putting a node for it in the tree, so the numbers |
| 152 |
* below are basically de-swizzled numbers. |
| 153 |
* The real slot is on idsel 0, so the swizzling is 1:1 |
| 154 |
*/ |
| 155 |
interrupt-map-mask = <0x0 0x0 0x0 0x7>; |
| 156 |
interrupt-map = < |
| 157 |
0x0 0x0 0x0 0x1 &MPIC 46 0x2 /* int A */ |
| 158 |
0x0 0x0 0x0 0x2 &MPIC 47 0x2 /* int B */ |
| 159 |
0x0 0x0 0x0 0x3 &MPIC 48 0x2 /* int C */ |
| 160 |
0x0 0x0 0x0 0x4 &MPIC 49 0x2 /* int D */>; |
| 161 |
}; |
| 162 |
|
| 163 |
PCIE1: pcie@30100000000 { // 4xGBIF0 |
| 164 |
device_type = "pci"; |
| 165 |
#interrupt-cells = <1>; |
| 166 |
#size-cells = <2>; |
| 167 |
#address-cells = <3>; |
| 168 |
compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex"; |
| 169 |
primary; |
| 170 |
port = <0x1>; /* port number */ |
| 171 |
reg = <0x00000301 0x00000000 0x0 0x10000000 /* Config space access */ |
| 172 |
0x00000300 0x00000000 0x0 0x00001000>; /* UTL Registers space access */ |
| 173 |
dcr-reg = <0x60 0x20>; |
| 174 |
|
| 175 |
ranges = <0x02000000 0x00000000 0x80000000 0x00000310 0x80000000 0x0 0x80000000 |
| 176 |
0x01000000 0x0 0x0 0x00000340 0x0 0x0 0x00010000>; |
| 177 |
|
| 178 |
/* Inbound starting at 0 to memsize filled in by zImage */ |
| 179 |
dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x0>; |
| 180 |
|
| 181 |
/* This drives busses 0 to 0xf */ |
| 182 |
bus-range = <0x0 0xf>; |
| 183 |
|
| 184 |
/* Legacy interrupts (note the weird polarity, the bridge seems |
| 185 |
* to invert PCIe legacy interrupts). |
| 186 |
* We are de-swizzling here because the numbers are actually for |
| 187 |
* port of the root complex virtual P2P bridge. But I want |
| 188 |
* to avoid putting a node for it in the tree, so the numbers |
| 189 |
* below are basically de-swizzled numbers. |
| 190 |
* The real slot is on idsel 0, so the swizzling is 1:1 |
| 191 |
*/ |
| 192 |
interrupt-map-mask = <0x0 0x0 0x0 0x7>; |
| 193 |
interrupt-map = < |
| 194 |
0x0 0x0 0x0 0x1 &MPIC 38 0x2 /* int A */ |
| 195 |
0x0 0x0 0x0 0x2 &MPIC 39 0x2 /* int B */ |
| 196 |
0x0 0x0 0x0 0x3 &MPIC 40 0x2 /* int C */ |
| 197 |
0x0 0x0 0x0 0x4 &MPIC 41 0x2 /* int D */>; |
| 198 |
}; |
| 199 |
|
| 200 |
PCIE2: pcie@38100000000 { // 2xGBIF0 |
| 201 |
device_type = "pci"; |
| 202 |
#interrupt-cells = <1>; |
| 203 |
#size-cells = <2>; |
| 204 |
#address-cells = <3>; |
| 205 |
compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex"; |
| 206 |
primary; |
| 207 |
port = <0x2>; /* port number */ |
| 208 |
reg = <0x00000381 0x00000000 0x0 0x10000000 /* Config space access */ |
| 209 |
0x00000380 0x00000000 0x0 0x00001000>; /* UTL Registers space access */ |
| 210 |
dcr-reg = <0xA0 0x20>; |
| 211 |
|
| 212 |
ranges = <0x02000000 0x00000000 0x80000000 0x00000390 0x80000000 0x0 0x80000000 |
| 213 |
0x01000000 0x0 0x0 0x000003C0 0x0 0x0 0x00010000>; |
| 214 |
|
| 215 |
/* Inbound starting at 0 to memsize filled in by zImage */ |
| 216 |
dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x0>; |
| 217 |
|
| 218 |
/* This drives busses 0 to 0xf */ |
| 219 |
bus-range = <0x0 0xf>; |
| 220 |
|
| 221 |
/* Legacy interrupts (note the weird polarity, the bridge seems |
| 222 |
* to invert PCIe legacy interrupts). |
| 223 |
* We are de-swizzling here because the numbers are actually for |
| 224 |
* port of the root complex virtual P2P bridge. But I want |
| 225 |
* to avoid putting a node for it in the tree, so the numbers |
| 226 |
* below are basically de-swizzled numbers. |
| 227 |
* The real slot is on idsel 0, so the swizzling is 1:1 |
| 228 |
*/ |
| 229 |
interrupt-map-mask = <0x0 0x0 0x0 0x7>; |
| 230 |
interrupt-map = < |
| 231 |
0x0 0x0 0x0 0x1 &MPIC 54 0x2 /* int A */ |
| 232 |
0x0 0x0 0x0 0x2 &MPIC 55 0x2 /* int B */ |
| 233 |
0x0 0x0 0x0 0x3 &MPIC 56 0x2 /* int C */ |
| 234 |
0x0 0x0 0x0 0x4 &MPIC 57 0x2 /* int D */>; |
| 235 |
}; |
| 236 |
|
| 237 |
}; |
| 238 |
|
| 239 |
chosen { |
| 240 |
stdout-path = &UART0; |
| 241 |
}; |
| 242 |
}; |