| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* dts file for Xilinx ZynqMP ZCU104 |
| 4 |
* |
| 5 |
* (C) Copyright 2017 - 2022, Xilinx, Inc. |
| 6 |
* (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. |
| 7 |
* |
| 8 |
* Michal Simek <[email protected]> |
| 9 |
*/ |
| 10 |
|
| 11 |
/dts-v1/; |
| 12 |
|
| 13 |
#include "zynqmp.dtsi" |
| 14 |
#include "zynqmp-clk-ccf.dtsi" |
| 15 |
#include <dt-bindings/gpio/gpio.h> |
| 16 |
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h> |
| 17 |
#include <dt-bindings/phy/phy.h> |
| 18 |
|
| 19 |
/ { |
| 20 |
model = "ZynqMP ZCU104 RevC"; |
| 21 |
compatible = "xlnx,zynqmp-zcu104-revC", "xlnx,zynqmp-zcu104", "xlnx,zynqmp"; |
| 22 |
|
| 23 |
aliases { |
| 24 |
ethernet0 = &gem3; |
| 25 |
i2c0 = &i2c1; |
| 26 |
mmc0 = &sdhci1; |
| 27 |
nvmem0 = &eeprom; |
| 28 |
rtc0 = &rtc; |
| 29 |
serial0 = &uart0; |
| 30 |
serial1 = &uart1; |
| 31 |
serial2 = &dcc; |
| 32 |
spi0 = &qspi; |
| 33 |
usb0 = &usb0; |
| 34 |
}; |
| 35 |
|
| 36 |
chosen { |
| 37 |
bootargs = "earlycon"; |
| 38 |
stdout-path = "serial0:115200n8"; |
| 39 |
}; |
| 40 |
|
| 41 |
memory@0 { |
| 42 |
device_type = "memory"; |
| 43 |
reg = <0x0 0x0 0x0 0x80000000>; |
| 44 |
}; |
| 45 |
|
| 46 |
ina226 { |
| 47 |
compatible = "iio-hwmon"; |
| 48 |
io-channels = <&u183 0>, <&u183 1>, <&u183 2>, <&u183 3>; |
| 49 |
}; |
| 50 |
|
| 51 |
clock_8t49n287_5: clk125 { |
| 52 |
compatible = "fixed-clock"; |
| 53 |
#clock-cells = <0>; |
| 54 |
clock-frequency = <125000000>; |
| 55 |
}; |
| 56 |
|
| 57 |
clock_8t49n287_2: clk26 { |
| 58 |
compatible = "fixed-clock"; |
| 59 |
#clock-cells = <0>; |
| 60 |
clock-frequency = <26000000>; |
| 61 |
}; |
| 62 |
|
| 63 |
clock_8t49n287_3: clk27 { |
| 64 |
compatible = "fixed-clock"; |
| 65 |
#clock-cells = <0>; |
| 66 |
clock-frequency = <27000000>; |
| 67 |
}; |
| 68 |
|
| 69 |
dpcon { |
| 70 |
compatible = "dp-connector"; |
| 71 |
label = "P11"; |
| 72 |
type = "full-size"; |
| 73 |
|
| 74 |
port { |
| 75 |
dpcon_in: endpoint { |
| 76 |
remote-endpoint = <&dpsub_dp_out>; |
| 77 |
}; |
| 78 |
}; |
| 79 |
}; |
| 80 |
}; |
| 81 |
|
| 82 |
&can1 { |
| 83 |
status = "okay"; |
| 84 |
pinctrl-names = "default"; |
| 85 |
pinctrl-0 = <&pinctrl_can1_default>; |
| 86 |
}; |
| 87 |
|
| 88 |
&dcc { |
| 89 |
status = "okay"; |
| 90 |
}; |
| 91 |
|
| 92 |
&fpd_dma_chan1 { |
| 93 |
status = "okay"; |
| 94 |
}; |
| 95 |
|
| 96 |
&fpd_dma_chan2 { |
| 97 |
status = "okay"; |
| 98 |
}; |
| 99 |
|
| 100 |
&fpd_dma_chan3 { |
| 101 |
status = "okay"; |
| 102 |
}; |
| 103 |
|
| 104 |
&fpd_dma_chan4 { |
| 105 |
status = "okay"; |
| 106 |
}; |
| 107 |
|
| 108 |
&fpd_dma_chan5 { |
| 109 |
status = "okay"; |
| 110 |
}; |
| 111 |
|
| 112 |
&fpd_dma_chan6 { |
| 113 |
status = "okay"; |
| 114 |
}; |
| 115 |
|
| 116 |
&fpd_dma_chan7 { |
| 117 |
status = "okay"; |
| 118 |
}; |
| 119 |
|
| 120 |
&fpd_dma_chan8 { |
| 121 |
status = "okay"; |
| 122 |
}; |
| 123 |
|
| 124 |
&gem3 { |
| 125 |
status = "okay"; |
| 126 |
phy-handle = <&phy0>; |
| 127 |
phy-mode = "rgmii-id"; |
| 128 |
pinctrl-names = "default"; |
| 129 |
pinctrl-0 = <&pinctrl_gem3_default>; |
| 130 |
mdio: mdio { |
| 131 |
#address-cells = <1>; |
| 132 |
#size-cells = <0>; |
| 133 |
phy0: ethernet-phy@c { |
| 134 |
#phy-cells = <1>; |
| 135 |
compatible = "ethernet-phy-id2000.a231"; |
| 136 |
reg = <0xc>; |
| 137 |
ti,rx-internal-delay = <0x8>; |
| 138 |
ti,tx-internal-delay = <0xa>; |
| 139 |
ti,fifo-depth = <0x1>; |
| 140 |
ti,dp83867-rxctrl-strap-quirk; |
| 141 |
reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; |
| 142 |
}; |
| 143 |
}; |
| 144 |
}; |
| 145 |
|
| 146 |
&gpio { |
| 147 |
status = "okay"; |
| 148 |
}; |
| 149 |
|
| 150 |
&gpu { |
| 151 |
status = "okay"; |
| 152 |
}; |
| 153 |
|
| 154 |
&i2c1 { |
| 155 |
status = "okay"; |
| 156 |
clock-frequency = <400000>; |
| 157 |
pinctrl-names = "default", "gpio"; |
| 158 |
pinctrl-0 = <&pinctrl_i2c1_default>; |
| 159 |
pinctrl-1 = <&pinctrl_i2c1_gpio>; |
| 160 |
scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 161 |
sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 162 |
|
| 163 |
tca6416_u97: gpio@20 { |
| 164 |
compatible = "ti,tca6416"; |
| 165 |
reg = <0x20>; |
| 166 |
gpio-controller; |
| 167 |
#gpio-cells = <2>; |
| 168 |
/* |
| 169 |
* IRQ not connected |
| 170 |
* Lines: |
| 171 |
* 0 - IRPS5401_ALERT_B |
| 172 |
* 1 - HDMI_8T49N241_INT_ALM |
| 173 |
* 2 - MAX6643_OT_B |
| 174 |
* 3 - MAX6643_FANFAIL_B |
| 175 |
* 5 - IIC_MUX_RESET_B |
| 176 |
* 6 - GEM3_EXP_RESET_B |
| 177 |
* 7 - FMC_LPC_PRSNT_M2C_B |
| 178 |
* 4, 10 - 17 - not connected |
| 179 |
*/ |
| 180 |
}; |
| 181 |
|
| 182 |
/* Another connection to this bus via PL i2c via PCA9306 - u45 */ |
| 183 |
i2c-mux@74 { /* u34 */ |
| 184 |
compatible = "nxp,pca9548"; |
| 185 |
#address-cells = <1>; |
| 186 |
#size-cells = <0>; |
| 187 |
reg = <0x74>; |
| 188 |
i2c@0 { |
| 189 |
#address-cells = <1>; |
| 190 |
#size-cells = <0>; |
| 191 |
reg = <0>; |
| 192 |
/* |
| 193 |
* IIC_EEPROM 1kB memory which uses 256B blocks |
| 194 |
* where every block has different address. |
| 195 |
* 0 - 256B address 0x54 |
| 196 |
* 256B - 512B address 0x55 |
| 197 |
* 512B - 768B address 0x56 |
| 198 |
* 768B - 1024B address 0x57 |
| 199 |
*/ |
| 200 |
eeprom: eeprom@54 { /* u23 */ |
| 201 |
compatible = "atmel,24c08"; |
| 202 |
reg = <0x54>; |
| 203 |
#address-cells = <1>; |
| 204 |
#size-cells = <1>; |
| 205 |
}; |
| 206 |
}; |
| 207 |
|
| 208 |
i2c@1 { |
| 209 |
#address-cells = <1>; |
| 210 |
#size-cells = <0>; |
| 211 |
reg = <1>; |
| 212 |
/* 8T49N287 - u182 */ |
| 213 |
}; |
| 214 |
|
| 215 |
i2c@2 { |
| 216 |
#address-cells = <1>; |
| 217 |
#size-cells = <0>; |
| 218 |
reg = <2>; |
| 219 |
irps5401_43: irps5401@43 { /* IRPS5401 - u175 */ |
| 220 |
compatible = "infineon,irps5401"; |
| 221 |
reg = <0x43>; /* pmbus / i2c 0x13 */ |
| 222 |
}; |
| 223 |
irps5401_44: irps5401@44 { /* IRPS5401 - u180 */ |
| 224 |
compatible = "infineon,irps5401"; |
| 225 |
reg = <0x44>; /* pmbus / i2c 0x14 */ |
| 226 |
}; |
| 227 |
}; |
| 228 |
|
| 229 |
i2c@3 { |
| 230 |
#address-cells = <1>; |
| 231 |
#size-cells = <0>; |
| 232 |
reg = <3>; |
| 233 |
u183: ina226@40 { /* u183 */ |
| 234 |
compatible = "ti,ina226"; |
| 235 |
#io-channel-cells = <1>; |
| 236 |
reg = <0x40>; |
| 237 |
shunt-resistor = <5000>; |
| 238 |
}; |
| 239 |
}; |
| 240 |
|
| 241 |
i2c@5 { |
| 242 |
#address-cells = <1>; |
| 243 |
#size-cells = <0>; |
| 244 |
reg = <5>; |
| 245 |
}; |
| 246 |
|
| 247 |
i2c@7 { |
| 248 |
#address-cells = <1>; |
| 249 |
#size-cells = <0>; |
| 250 |
reg = <7>; |
| 251 |
}; |
| 252 |
|
| 253 |
/* 4, 6 not connected */ |
| 254 |
}; |
| 255 |
}; |
| 256 |
|
| 257 |
&pinctrl0 { |
| 258 |
status = "okay"; |
| 259 |
|
| 260 |
pinctrl_can1_default: can1-default { |
| 261 |
mux { |
| 262 |
function = "can1"; |
| 263 |
groups = "can1_6_grp"; |
| 264 |
}; |
| 265 |
|
| 266 |
conf { |
| 267 |
groups = "can1_6_grp"; |
| 268 |
slew-rate = <SLEW_RATE_SLOW>; |
| 269 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 270 |
drive-strength = <12>; |
| 271 |
}; |
| 272 |
|
| 273 |
conf-rx { |
| 274 |
pins = "MIO25"; |
| 275 |
bias-high-impedance; |
| 276 |
}; |
| 277 |
|
| 278 |
conf-tx { |
| 279 |
pins = "MIO24"; |
| 280 |
bias-disable; |
| 281 |
}; |
| 282 |
}; |
| 283 |
|
| 284 |
pinctrl_i2c1_default: i2c1-default { |
| 285 |
mux { |
| 286 |
groups = "i2c1_4_grp"; |
| 287 |
function = "i2c1"; |
| 288 |
}; |
| 289 |
|
| 290 |
conf { |
| 291 |
groups = "i2c1_4_grp"; |
| 292 |
bias-pull-up; |
| 293 |
slew-rate = <SLEW_RATE_SLOW>; |
| 294 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 295 |
drive-strength = <12>; |
| 296 |
}; |
| 297 |
}; |
| 298 |
|
| 299 |
pinctrl_i2c1_gpio: i2c1-gpio-grp { |
| 300 |
mux { |
| 301 |
groups = "gpio0_16_grp", "gpio0_17_grp"; |
| 302 |
function = "gpio0"; |
| 303 |
}; |
| 304 |
|
| 305 |
conf { |
| 306 |
groups = "gpio0_16_grp", "gpio0_17_grp"; |
| 307 |
slew-rate = <SLEW_RATE_SLOW>; |
| 308 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 309 |
drive-strength = <12>; |
| 310 |
}; |
| 311 |
}; |
| 312 |
|
| 313 |
pinctrl_gem3_default: gem3-default { |
| 314 |
mux { |
| 315 |
function = "ethernet3"; |
| 316 |
groups = "ethernet3_0_grp"; |
| 317 |
}; |
| 318 |
|
| 319 |
conf { |
| 320 |
groups = "ethernet3_0_grp"; |
| 321 |
slew-rate = <SLEW_RATE_SLOW>; |
| 322 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 323 |
drive-strength = <12>; |
| 324 |
}; |
| 325 |
|
| 326 |
conf-rx { |
| 327 |
pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74", |
| 328 |
"MIO75"; |
| 329 |
bias-high-impedance; |
| 330 |
low-power-disable; |
| 331 |
}; |
| 332 |
|
| 333 |
conf-tx { |
| 334 |
pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68", |
| 335 |
"MIO69"; |
| 336 |
bias-disable; |
| 337 |
low-power-enable; |
| 338 |
}; |
| 339 |
|
| 340 |
mux-mdio { |
| 341 |
function = "mdio3"; |
| 342 |
groups = "mdio3_0_grp"; |
| 343 |
}; |
| 344 |
|
| 345 |
conf-mdio { |
| 346 |
groups = "mdio3_0_grp"; |
| 347 |
slew-rate = <SLEW_RATE_SLOW>; |
| 348 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 349 |
bias-disable; |
| 350 |
}; |
| 351 |
}; |
| 352 |
|
| 353 |
pinctrl_sdhci1_default: sdhci1-default { |
| 354 |
mux { |
| 355 |
groups = "sdio1_0_grp"; |
| 356 |
function = "sdio1"; |
| 357 |
}; |
| 358 |
|
| 359 |
conf { |
| 360 |
groups = "sdio1_0_grp"; |
| 361 |
slew-rate = <SLEW_RATE_SLOW>; |
| 362 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 363 |
bias-disable; |
| 364 |
drive-strength = <12>; |
| 365 |
}; |
| 366 |
|
| 367 |
mux-cd { |
| 368 |
groups = "sdio1_cd_0_grp"; |
| 369 |
function = "sdio1_cd"; |
| 370 |
}; |
| 371 |
|
| 372 |
conf-cd { |
| 373 |
groups = "sdio1_cd_0_grp"; |
| 374 |
bias-high-impedance; |
| 375 |
bias-pull-up; |
| 376 |
slew-rate = <SLEW_RATE_SLOW>; |
| 377 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 378 |
}; |
| 379 |
}; |
| 380 |
|
| 381 |
pinctrl_uart0_default: uart0-default { |
| 382 |
mux { |
| 383 |
groups = "uart0_4_grp"; |
| 384 |
function = "uart0"; |
| 385 |
}; |
| 386 |
|
| 387 |
conf { |
| 388 |
groups = "uart0_4_grp"; |
| 389 |
slew-rate = <SLEW_RATE_SLOW>; |
| 390 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 391 |
drive-strength = <12>; |
| 392 |
}; |
| 393 |
|
| 394 |
conf-rx { |
| 395 |
pins = "MIO18"; |
| 396 |
bias-high-impedance; |
| 397 |
}; |
| 398 |
|
| 399 |
conf-tx { |
| 400 |
pins = "MIO19"; |
| 401 |
bias-disable; |
| 402 |
}; |
| 403 |
}; |
| 404 |
|
| 405 |
pinctrl_uart1_default: uart1-default { |
| 406 |
mux { |
| 407 |
groups = "uart1_5_grp"; |
| 408 |
function = "uart1"; |
| 409 |
}; |
| 410 |
|
| 411 |
conf { |
| 412 |
groups = "uart1_5_grp"; |
| 413 |
slew-rate = <SLEW_RATE_SLOW>; |
| 414 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 415 |
drive-strength = <12>; |
| 416 |
}; |
| 417 |
|
| 418 |
conf-rx { |
| 419 |
pins = "MIO21"; |
| 420 |
bias-high-impedance; |
| 421 |
}; |
| 422 |
|
| 423 |
conf-tx { |
| 424 |
pins = "MIO20"; |
| 425 |
bias-disable; |
| 426 |
}; |
| 427 |
}; |
| 428 |
|
| 429 |
pinctrl_usb0_default: usb0-default { |
| 430 |
mux { |
| 431 |
groups = "usb0_0_grp"; |
| 432 |
function = "usb0"; |
| 433 |
}; |
| 434 |
|
| 435 |
conf { |
| 436 |
groups = "usb0_0_grp"; |
| 437 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 438 |
}; |
| 439 |
|
| 440 |
conf-rx { |
| 441 |
pins = "MIO52", "MIO53", "MIO55"; |
| 442 |
bias-high-impedance; |
| 443 |
drive-strength = <12>; |
| 444 |
slew-rate = <SLEW_RATE_FAST>; |
| 445 |
}; |
| 446 |
|
| 447 |
conf-tx { |
| 448 |
pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", |
| 449 |
"MIO60", "MIO61", "MIO62", "MIO63"; |
| 450 |
bias-disable; |
| 451 |
drive-strength = <4>; |
| 452 |
slew-rate = <SLEW_RATE_SLOW>; |
| 453 |
}; |
| 454 |
}; |
| 455 |
}; |
| 456 |
|
| 457 |
&psgtr { |
| 458 |
status = "okay"; |
| 459 |
/* nc, sata, usb3, dp */ |
| 460 |
clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>; |
| 461 |
clock-names = "ref1", "ref2", "ref3"; |
| 462 |
}; |
| 463 |
|
| 464 |
&qspi { |
| 465 |
status = "okay"; |
| 466 |
flash@0 { |
| 467 |
compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */ |
| 468 |
#address-cells = <1>; |
| 469 |
#size-cells = <1>; |
| 470 |
reg = <0x0>; |
| 471 |
spi-tx-bus-width = <4>; |
| 472 |
spi-rx-bus-width = <4>; |
| 473 |
spi-max-frequency = <108000000>; /* Based on DC1 spec */ |
| 474 |
}; |
| 475 |
}; |
| 476 |
|
| 477 |
&rtc { |
| 478 |
status = "okay"; |
| 479 |
}; |
| 480 |
|
| 481 |
&sata { |
| 482 |
status = "okay"; |
| 483 |
/* SATA OOB timing settings */ |
| 484 |
ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; |
| 485 |
ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; |
| 486 |
ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; |
| 487 |
ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>; |
| 488 |
ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; |
| 489 |
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; |
| 490 |
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; |
| 491 |
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; |
| 492 |
phy-names = "sata-phy"; |
| 493 |
phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; |
| 494 |
}; |
| 495 |
|
| 496 |
/* SD1 with level shifter */ |
| 497 |
&sdhci1 { |
| 498 |
status = "okay"; |
| 499 |
no-1-8-v; |
| 500 |
pinctrl-names = "default"; |
| 501 |
pinctrl-0 = <&pinctrl_sdhci1_default>; |
| 502 |
xlnx,mio-bank = <1>; |
| 503 |
disable-wp; |
| 504 |
}; |
| 505 |
|
| 506 |
&uart0 { |
| 507 |
status = "okay"; |
| 508 |
pinctrl-names = "default"; |
| 509 |
pinctrl-0 = <&pinctrl_uart0_default>; |
| 510 |
}; |
| 511 |
|
| 512 |
&uart1 { |
| 513 |
status = "okay"; |
| 514 |
pinctrl-names = "default"; |
| 515 |
pinctrl-0 = <&pinctrl_uart1_default>; |
| 516 |
}; |
| 517 |
|
| 518 |
/* ULPI SMSC USB3320 */ |
| 519 |
&usb0 { |
| 520 |
status = "okay"; |
| 521 |
pinctrl-names = "default"; |
| 522 |
pinctrl-0 = <&pinctrl_usb0_default>; |
| 523 |
phy-names = "usb3-phy"; |
| 524 |
phys = <&psgtr 2 PHY_TYPE_USB3 0 2>; |
| 525 |
}; |
| 526 |
|
| 527 |
&dwc3_0 { |
| 528 |
status = "okay"; |
| 529 |
dr_mode = "host"; |
| 530 |
snps,usb3_lpm_capable; |
| 531 |
maximum-speed = "super-speed"; |
| 532 |
}; |
| 533 |
|
| 534 |
&watchdog0 { |
| 535 |
status = "okay"; |
| 536 |
}; |
| 537 |
|
| 538 |
&ams_ps { |
| 539 |
status = "okay"; |
| 540 |
}; |
| 541 |
|
| 542 |
&ams_pl { |
| 543 |
status = "okay"; |
| 544 |
}; |
| 545 |
|
| 546 |
&zynqmp_dpdma { |
| 547 |
status = "okay"; |
| 548 |
}; |
| 549 |
|
| 550 |
&zynqmp_dpsub { |
| 551 |
status = "okay"; |
| 552 |
phy-names = "dp-phy0", "dp-phy1"; |
| 553 |
phys = <&psgtr 1 PHY_TYPE_DP 0 3>, |
| 554 |
<&psgtr 0 PHY_TYPE_DP 1 3>; |
| 555 |
}; |
| 556 |
|
| 557 |
&out_dp { |
| 558 |
dpsub_dp_out: endpoint { |
| 559 |
remote-endpoint = <&dpcon_in>; |
| 560 |
}; |
| 561 |
}; |