Debian Codegraph @

scripts/dtc/include-prefixes/arm64/xilinx/zynqmp-zcu104-revA.dts

raw
1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * dts file for Xilinx ZynqMP ZCU104
4 *
5 * (C) Copyright 2017 - 2022, Xilinx, Inc.
6 * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
7 *
8 * Michal Simek <[email protected]>
9 */
10
11 /dts-v1/;
12
13 #include "zynqmp.dtsi"
14 #include "zynqmp-clk-ccf.dtsi"
15 #include <dt-bindings/gpio/gpio.h>
16 #include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
17 #include <dt-bindings/phy/phy.h>
18
19 / {
20 model = "ZynqMP ZCU104 RevA";
21 compatible = "xlnx,zynqmp-zcu104-revA", "xlnx,zynqmp-zcu104", "xlnx,zynqmp";
22
23 aliases {
24 ethernet0 = &gem3;
25 i2c0 = &i2c1;
26 mmc0 = &sdhci1;
27 nvmem0 = &eeprom;
28 rtc0 = &rtc;
29 serial0 = &uart0;
30 serial1 = &uart1;
31 serial2 = &dcc;
32 spi0 = &qspi;
33 usb0 = &usb0;
34 };
35
36 chosen {
37 bootargs = "earlycon";
38 stdout-path = "serial0:115200n8";
39 };
40
41 memory@0 {
42 device_type = "memory";
43 reg = <0x0 0x0 0x0 0x80000000>;
44 };
45
46 clock_8t49n287_5: clk125 {
47 compatible = "fixed-clock";
48 #clock-cells = <0>;
49 clock-frequency = <125000000>;
50 };
51
52 clock_8t49n287_2: clk26 {
53 compatible = "fixed-clock";
54 #clock-cells = <0>;
55 clock-frequency = <26000000>;
56 };
57
58 clock_8t49n287_3: clk27 {
59 compatible = "fixed-clock";
60 #clock-cells = <0>;
61 clock-frequency = <27000000>;
62 };
63
64 dpcon {
65 compatible = "dp-connector";
66 label = "P11";
67 type = "full-size";
68
69 port {
70 dpcon_in: endpoint {
71 remote-endpoint = <&dpsub_dp_out>;
72 };
73 };
74 };
75 };
76
77 &can1 {
78 status = "okay";
79 pinctrl-names = "default";
80 pinctrl-0 = <&pinctrl_can1_default>;
81 };
82
83 &dcc {
84 status = "okay";
85 };
86
87 &fpd_dma_chan1 {
88 status = "okay";
89 };
90
91 &fpd_dma_chan2 {
92 status = "okay";
93 };
94
95 &fpd_dma_chan3 {
96 status = "okay";
97 };
98
99 &fpd_dma_chan4 {
100 status = "okay";
101 };
102
103 &fpd_dma_chan5 {
104 status = "okay";
105 };
106
107 &fpd_dma_chan6 {
108 status = "okay";
109 };
110
111 &fpd_dma_chan7 {
112 status = "okay";
113 };
114
115 &fpd_dma_chan8 {
116 status = "okay";
117 };
118
119 &gem3 {
120 status = "okay";
121 phy-handle = <&phy0>;
122 phy-mode = "rgmii-id";
123 pinctrl-names = "default";
124 pinctrl-0 = <&pinctrl_gem3_default>;
125 mdio: mdio {
126 #address-cells = <1>;
127 #size-cells = <0>;
128 phy0: ethernet-phy@c {
129 #phy-cells = <1>;
130 compatible = "ethernet-phy-id2000.a231";
131 reg = <0xc>;
132 ti,rx-internal-delay = <0x8>;
133 ti,tx-internal-delay = <0xa>;
134 ti,fifo-depth = <0x1>;
135 ti,dp83867-rxctrl-strap-quirk;
136 reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
137 };
138 };
139 };
140
141 &gpio {
142 status = "okay";
143 };
144
145 &gpu {
146 status = "okay";
147 };
148
149 &i2c1 {
150 status = "okay";
151 clock-frequency = <400000>;
152 pinctrl-names = "default", "gpio";
153 pinctrl-0 = <&pinctrl_i2c1_default>;
154 pinctrl-1 = <&pinctrl_i2c1_gpio>;
155 scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
156 sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
157
158 /* Another connection to this bus via PL i2c via PCA9306 - u45 */
159 i2c-mux@74 { /* u34 */
160 compatible = "nxp,pca9548";
161 #address-cells = <1>;
162 #size-cells = <0>;
163 reg = <0x74>;
164 i2c@0 {
165 #address-cells = <1>;
166 #size-cells = <0>;
167 reg = <0>;
168 /*
169 * IIC_EEPROM 1kB memory which uses 256B blocks
170 * where every block has different address.
171 * 0 - 256B address 0x54
172 * 256B - 512B address 0x55
173 * 512B - 768B address 0x56
174 * 768B - 1024B address 0x57
175 */
176 eeprom: eeprom@54 { /* u23 */
177 compatible = "atmel,24c08";
178 reg = <0x54>;
179 #address-cells = <1>;
180 #size-cells = <1>;
181 };
182 };
183
184 i2c@1 {
185 #address-cells = <1>;
186 #size-cells = <0>;
187 reg = <1>;
188 /* 8T49N287 - u182 */
189 };
190
191 i2c@2 {
192 #address-cells = <1>;
193 #size-cells = <0>;
194 reg = <2>;
195 irps5401_43: irps5401@43 { /* IRPS5401 - u175 */
196 compatible = "infineon,irps5401";
197 reg = <0x43>; /* pmbus / i2c 0x13 */
198 };
199 irps5401_44: irps5401@44 { /* IRPS5401 - u180 */
200 compatible = "infineon,irps5401";
201 reg = <0x44>; /* pmbus / i2c 0x14 */
202 };
203 };
204
205 i2c@4 {
206 #address-cells = <1>;
207 #size-cells = <0>;
208 reg = <4>;
209 tca6416_u97: gpio@20 {
210 compatible = "ti,tca6416";
211 reg = <0x20>;
212 gpio-controller;
213 #gpio-cells = <2>;
214 /*
215 * IRQ not connected
216 * Lines:
217 * 0 - IRPS5401_ALERT_B
218 * 1 - HDMI_8T49N241_INT_ALM
219 * 2 - MAX6643_OT_B
220 * 3 - MAX6643_FANFAIL_B
221 * 5 - IIC_MUX_RESET_B
222 * 6 - GEM3_EXP_RESET_B
223 * 7 - FMC_LPC_PRSNT_M2C_B
224 * 4, 10 - 17 - not connected
225 */
226 };
227 };
228
229 i2c@5 {
230 #address-cells = <1>;
231 #size-cells = <0>;
232 reg = <5>;
233 };
234
235 i2c@7 {
236 #address-cells = <1>;
237 #size-cells = <0>;
238 reg = <7>;
239 };
240
241 /* 3, 6 not connected */
242 };
243 };
244
245 &pinctrl0 {
246 status = "okay";
247
248 pinctrl_can1_default: can1-default {
249 mux {
250 function = "can1";
251 groups = "can1_6_grp";
252 };
253
254 conf {
255 groups = "can1_6_grp";
256 slew-rate = <SLEW_RATE_SLOW>;
257 power-source = <IO_STANDARD_LVCMOS18>;
258 drive-strength = <12>;
259 };
260
261 conf-rx {
262 pins = "MIO25";
263 bias-high-impedance;
264 };
265
266 conf-tx {
267 pins = "MIO24";
268 bias-disable;
269 };
270 };
271
272 pinctrl_i2c1_default: i2c1-default {
273 mux {
274 groups = "i2c1_4_grp";
275 function = "i2c1";
276 };
277
278 conf {
279 groups = "i2c1_4_grp";
280 bias-pull-up;
281 slew-rate = <SLEW_RATE_SLOW>;
282 power-source = <IO_STANDARD_LVCMOS18>;
283 drive-strength = <12>;
284 };
285 };
286
287 pinctrl_i2c1_gpio: i2c1-gpio-grp {
288 mux {
289 groups = "gpio0_16_grp", "gpio0_17_grp";
290 function = "gpio0";
291 };
292
293 conf {
294 groups = "gpio0_16_grp", "gpio0_17_grp";
295 slew-rate = <SLEW_RATE_SLOW>;
296 power-source = <IO_STANDARD_LVCMOS18>;
297 drive-strength = <12>;
298 };
299 };
300
301 pinctrl_gem3_default: gem3-default {
302 mux {
303 function = "ethernet3";
304 groups = "ethernet3_0_grp";
305 };
306
307 conf {
308 groups = "ethernet3_0_grp";
309 slew-rate = <SLEW_RATE_SLOW>;
310 power-source = <IO_STANDARD_LVCMOS18>;
311 drive-strength = <12>;
312 };
313
314 conf-rx {
315 pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
316 "MIO75";
317 bias-high-impedance;
318 low-power-disable;
319 };
320
321 conf-tx {
322 pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
323 "MIO69";
324 bias-disable;
325 low-power-enable;
326 };
327
328 mux-mdio {
329 function = "mdio3";
330 groups = "mdio3_0_grp";
331 };
332
333 conf-mdio {
334 groups = "mdio3_0_grp";
335 slew-rate = <SLEW_RATE_SLOW>;
336 power-source = <IO_STANDARD_LVCMOS18>;
337 bias-disable;
338 };
339 };
340
341 pinctrl_sdhci1_default: sdhci1-default {
342 mux {
343 groups = "sdio1_0_grp";
344 function = "sdio1";
345 };
346
347 conf {
348 groups = "sdio1_0_grp";
349 slew-rate = <SLEW_RATE_SLOW>;
350 power-source = <IO_STANDARD_LVCMOS18>;
351 bias-disable;
352 drive-strength = <12>;
353 };
354
355 mux-cd {
356 groups = "sdio1_cd_0_grp";
357 function = "sdio1_cd";
358 };
359
360 conf-cd {
361 groups = "sdio1_cd_0_grp";
362 bias-high-impedance;
363 bias-pull-up;
364 slew-rate = <SLEW_RATE_SLOW>;
365 power-source = <IO_STANDARD_LVCMOS18>;
366 };
367 };
368
369 pinctrl_uart0_default: uart0-default {
370 mux {
371 groups = "uart0_4_grp";
372 function = "uart0";
373 };
374
375 conf {
376 groups = "uart0_4_grp";
377 slew-rate = <SLEW_RATE_SLOW>;
378 power-source = <IO_STANDARD_LVCMOS18>;
379 drive-strength = <12>;
380 };
381
382 conf-rx {
383 pins = "MIO18";
384 bias-high-impedance;
385 };
386
387 conf-tx {
388 pins = "MIO19";
389 bias-disable;
390 };
391 };
392
393 pinctrl_uart1_default: uart1-default {
394 mux {
395 groups = "uart1_5_grp";
396 function = "uart1";
397 };
398
399 conf {
400 groups = "uart1_5_grp";
401 slew-rate = <SLEW_RATE_SLOW>;
402 power-source = <IO_STANDARD_LVCMOS18>;
403 drive-strength = <12>;
404 };
405
406 conf-rx {
407 pins = "MIO21";
408 bias-high-impedance;
409 };
410
411 conf-tx {
412 pins = "MIO20";
413 bias-disable;
414 };
415 };
416
417 pinctrl_usb0_default: usb0-default {
418 mux {
419 groups = "usb0_0_grp";
420 function = "usb0";
421 };
422
423 conf {
424 groups = "usb0_0_grp";
425 power-source = <IO_STANDARD_LVCMOS18>;
426 };
427
428 conf-rx {
429 pins = "MIO52", "MIO53", "MIO55";
430 bias-high-impedance;
431 drive-strength = <12>;
432 slew-rate = <SLEW_RATE_FAST>;
433 };
434
435 conf-tx {
436 pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
437 "MIO60", "MIO61", "MIO62", "MIO63";
438 bias-disable;
439 drive-strength = <4>;
440 slew-rate = <SLEW_RATE_SLOW>;
441 };
442 };
443 };
444
445 &psgtr {
446 status = "okay";
447 /* nc, sata, usb3, dp */
448 clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
449 clock-names = "ref1", "ref2", "ref3";
450 };
451
452 &qspi {
453 status = "okay";
454 flash@0 {
455 compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */
456 #address-cells = <1>;
457 #size-cells = <1>;
458 reg = <0x0>;
459 spi-tx-bus-width = <4>;
460 spi-rx-bus-width = <4>;
461 spi-max-frequency = <108000000>; /* Based on DC1 spec */
462 };
463 };
464
465 &rtc {
466 status = "okay";
467 };
468
469 &sata {
470 status = "okay";
471 /* SATA OOB timing settings */
472 ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
473 ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
474 ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
475 ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
476 ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
477 ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
478 ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
479 ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
480 phy-names = "sata-phy";
481 phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
482 };
483
484 /* SD1 with level shifter */
485 &sdhci1 {
486 status = "okay";
487 no-1-8-v;
488 pinctrl-names = "default";
489 pinctrl-0 = <&pinctrl_sdhci1_default>;
490 xlnx,mio-bank = <1>;
491 disable-wp;
492 };
493
494 &uart0 {
495 status = "okay";
496 pinctrl-names = "default";
497 pinctrl-0 = <&pinctrl_uart0_default>;
498 };
499
500 &uart1 {
501 status = "okay";
502 pinctrl-names = "default";
503 pinctrl-0 = <&pinctrl_uart1_default>;
504 };
505
506 /* ULPI SMSC USB3320 */
507 &usb0 {
508 status = "okay";
509 pinctrl-names = "default";
510 pinctrl-0 = <&pinctrl_usb0_default>;
511 phy-names = "usb3-phy";
512 phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
513 };
514
515 &dwc3_0 {
516 status = "okay";
517 dr_mode = "host";
518 snps,usb3_lpm_capable;
519 maximum-speed = "super-speed";
520 };
521
522 &watchdog0 {
523 status = "okay";
524 };
525
526 &ams_ps {
527 status = "okay";
528 };
529
530 &ams_pl {
531 status = "okay";
532 };
533
534 &zynqmp_dpdma {
535 status = "okay";
536 };
537
538 &zynqmp_dpsub {
539 status = "okay";
540 phy-names = "dp-phy0", "dp-phy1";
541 phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
542 <&psgtr 0 PHY_TYPE_DP 1 3>;
543 };
544
545 &out_dp {
546 dpsub_dp_out: endpoint {
547 remote-endpoint = <&dpcon_in>;
548 };
549 };