Debian Codegraph @

scripts/dtc/include-prefixes/arm64/xilinx/zynqmp-zcu102-revA.dts

raw
1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * dts file for Xilinx ZynqMP ZCU102 RevA
4 *
5 * (C) Copyright 2015 - 2022, Xilinx, Inc.
6 * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
7 *
8 * Michal Simek <[email protected]>
9 */
10
11 /dts-v1/;
12
13 #include "zynqmp.dtsi"
14 #include "zynqmp-clk-ccf.dtsi"
15 #include <dt-bindings/input/input.h>
16 #include <dt-bindings/gpio/gpio.h>
17 #include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
18 #include <dt-bindings/phy/phy.h>
19
20 / {
21 model = "ZynqMP ZCU102 RevA";
22 compatible = "xlnx,zynqmp-zcu102-revA", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
23
24 aliases {
25 ethernet0 = &gem3;
26 i2c0 = &i2c0;
27 i2c1 = &i2c1;
28 mmc0 = &sdhci1;
29 nvmem0 = &eeprom;
30 rtc0 = &rtc;
31 serial0 = &uart0;
32 serial1 = &uart1;
33 serial2 = &dcc;
34 spi0 = &qspi;
35 usb0 = &usb0;
36 };
37
38 chosen {
39 bootargs = "earlycon";
40 stdout-path = "serial0:115200n8";
41 };
42
43 memory@0 {
44 device_type = "memory";
45 reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
46 };
47
48 gpio-keys {
49 compatible = "gpio-keys";
50 autorepeat;
51 switch-19 {
52 label = "sw19";
53 gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
54 linux,code = <KEY_DOWN>;
55 wakeup-source;
56 autorepeat;
57 };
58 };
59
60 leds {
61 compatible = "gpio-leds";
62 heartbeat-led {
63 label = "heartbeat";
64 gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
65 linux,default-trigger = "heartbeat";
66 };
67 };
68
69 ina226-u76 {
70 compatible = "iio-hwmon";
71 io-channels = <&u76 0>, <&u76 1>, <&u76 2>, <&u76 3>;
72 };
73 ina226-u77 {
74 compatible = "iio-hwmon";
75 io-channels = <&u77 0>, <&u77 1>, <&u77 2>, <&u77 3>;
76 };
77 ina226-u78 {
78 compatible = "iio-hwmon";
79 io-channels = <&u78 0>, <&u78 1>, <&u78 2>, <&u78 3>;
80 };
81 ina226-u87 {
82 compatible = "iio-hwmon";
83 io-channels = <&u87 0>, <&u87 1>, <&u87 2>, <&u87 3>;
84 };
85 ina226-u85 {
86 compatible = "iio-hwmon";
87 io-channels = <&u85 0>, <&u85 1>, <&u85 2>, <&u85 3>;
88 };
89 ina226-u86 {
90 compatible = "iio-hwmon";
91 io-channels = <&u86 0>, <&u86 1>, <&u86 2>, <&u86 3>;
92 };
93 ina226-u93 {
94 compatible = "iio-hwmon";
95 io-channels = <&u93 0>, <&u93 1>, <&u93 2>, <&u93 3>;
96 };
97 ina226-u88 {
98 compatible = "iio-hwmon";
99 io-channels = <&u88 0>, <&u88 1>, <&u88 2>, <&u88 3>;
100 };
101 ina226-u15 {
102 compatible = "iio-hwmon";
103 io-channels = <&u15 0>, <&u15 1>, <&u15 2>, <&u15 3>;
104 };
105 ina226-u92 {
106 compatible = "iio-hwmon";
107 io-channels = <&u92 0>, <&u92 1>, <&u92 2>, <&u92 3>;
108 };
109 ina226-u79 {
110 compatible = "iio-hwmon";
111 io-channels = <&u79 0>, <&u79 1>, <&u79 2>, <&u79 3>;
112 };
113 ina226-u81 {
114 compatible = "iio-hwmon";
115 io-channels = <&u81 0>, <&u81 1>, <&u81 2>, <&u81 3>;
116 };
117 ina226-u80 {
118 compatible = "iio-hwmon";
119 io-channels = <&u80 0>, <&u80 1>, <&u80 2>, <&u80 3>;
120 };
121 ina226-u84 {
122 compatible = "iio-hwmon";
123 io-channels = <&u84 0>, <&u84 1>, <&u84 2>, <&u84 3>;
124 };
125 ina226-u16 {
126 compatible = "iio-hwmon";
127 io-channels = <&u16 0>, <&u16 1>, <&u16 2>, <&u16 3>;
128 };
129 ina226-u65 {
130 compatible = "iio-hwmon";
131 io-channels = <&u65 0>, <&u65 1>, <&u65 2>, <&u65 3>;
132 };
133 ina226-u74 {
134 compatible = "iio-hwmon";
135 io-channels = <&u74 0>, <&u74 1>, <&u74 2>, <&u74 3>;
136 };
137 ina226-u75 {
138 compatible = "iio-hwmon";
139 io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>;
140 };
141
142 /* 48MHz reference crystal */
143 ref48: ref48M {
144 compatible = "fixed-clock";
145 #clock-cells = <0>;
146 clock-frequency = <48000000>;
147 };
148
149 refhdmi: refhdmi {
150 compatible = "fixed-clock";
151 #clock-cells = <0>;
152 clock-frequency = <114285000>;
153 };
154
155 dpcon {
156 compatible = "dp-connector";
157 label = "P11";
158 type = "full-size";
159
160 port {
161 dpcon_in: endpoint {
162 remote-endpoint = <&dpsub_dp_out>;
163 };
164 };
165 };
166 };
167
168 &can1 {
169 status = "okay";
170 pinctrl-names = "default";
171 pinctrl-0 = <&pinctrl_can1_default>;
172 };
173
174 &dcc {
175 status = "okay";
176 };
177
178 &fpd_dma_chan1 {
179 status = "okay";
180 };
181
182 &fpd_dma_chan2 {
183 status = "okay";
184 };
185
186 &fpd_dma_chan3 {
187 status = "okay";
188 };
189
190 &fpd_dma_chan4 {
191 status = "okay";
192 };
193
194 &fpd_dma_chan5 {
195 status = "okay";
196 };
197
198 &fpd_dma_chan6 {
199 status = "okay";
200 };
201
202 &fpd_dma_chan7 {
203 status = "okay";
204 };
205
206 &fpd_dma_chan8 {
207 status = "okay";
208 };
209
210 &gem3 {
211 status = "okay";
212 phy-handle = <&phy0>;
213 phy-mode = "rgmii-id";
214 pinctrl-names = "default";
215 pinctrl-0 = <&pinctrl_gem3_default>;
216 mdio: mdio {
217 #address-cells = <1>;
218 #size-cells = <0>;
219 phy0: ethernet-phy@21 {
220 #phy-cells = <1>;
221 compatible = "ethernet-phy-id2000.a231";
222 reg = <21>;
223 ti,rx-internal-delay = <0x8>;
224 ti,tx-internal-delay = <0xa>;
225 ti,fifo-depth = <0x1>;
226 ti,dp83867-rxctrl-strap-quirk;
227 reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
228 };
229 };
230 };
231
232 &gpio {
233 status = "okay";
234 pinctrl-names = "default";
235 pinctrl-0 = <&pinctrl_gpio_default>;
236 };
237
238 &gpu {
239 status = "okay";
240 };
241
242 &i2c0 {
243 status = "okay";
244 clock-frequency = <400000>;
245 pinctrl-names = "default", "gpio";
246 pinctrl-0 = <&pinctrl_i2c0_default>;
247 pinctrl-1 = <&pinctrl_i2c0_gpio>;
248 scl-gpios = <&gpio 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
249 sda-gpios = <&gpio 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
250
251 tca6416_u97: gpio@20 {
252 compatible = "ti,tca6416";
253 reg = <0x20>;
254 gpio-controller; /* IRQ not connected */
255 #gpio-cells = <2>;
256 gpio-line-names = "PS_GTR_LAN_SEL0", "PS_GTR_LAN_SEL1", "PS_GTR_LAN_SEL2", "PS_GTR_LAN_SEL3",
257 "PCI_CLK_DIR_SEL", "IIC_MUX_RESET_B", "GEM3_EXP_RESET_B",
258 "", "", "", "", "", "", "", "", "";
259 gtr-sel0-hog {
260 gpio-hog;
261 gpios = <0 0>;
262 output-low; /* PCIE = 0, DP = 1 */
263 line-name = "sel0";
264 };
265 gtr-sel1-hog {
266 gpio-hog;
267 gpios = <1 0>;
268 output-high; /* PCIE = 0, DP = 1 */
269 line-name = "sel1";
270 };
271 gtr-sel2-hog {
272 gpio-hog;
273 gpios = <2 0>;
274 output-high; /* PCIE = 0, USB0 = 1 */
275 line-name = "sel2";
276 };
277 gtr-sel3-hog {
278 gpio-hog;
279 gpios = <3 0>;
280 output-high; /* PCIE = 0, SATA = 1 */
281 line-name = "sel3";
282 };
283 };
284
285 tca6416_u61: gpio@21 {
286 compatible = "ti,tca6416";
287 reg = <0x21>;
288 gpio-controller; /* IRQ not connected */
289 #gpio-cells = <2>;
290 gpio-line-names = "VCCPSPLL_EN", "MGTRAVCC_EN", "MGTRAVTT_EN", "VCCPSDDRPLL_EN", "MIO26_PMU_INPUT_LS",
291 "PL_PMBUS_ALERT", "PS_PMBUS_ALERT", "MAXIM_PMBUS_ALERT", "PL_DDR4_VTERM_EN",
292 "PL_DDR4_VPP_2V5_EN", "PS_DIMM_VDDQ_TO_PSVCCO_ON", "PS_DIMM_SUSPEND_EN",
293 "PS_DDR4_VTERM_EN", "PS_DDR4_VPP_2V5_EN", "", "";
294 };
295
296 i2c-mux@75 { /* u60 */
297 compatible = "nxp,pca9544";
298 #address-cells = <1>;
299 #size-cells = <0>;
300 reg = <0x75>;
301 i2c@0 {
302 #address-cells = <1>;
303 #size-cells = <0>;
304 reg = <0>;
305 /* PS_PMBUS */
306 u76: ina226@40 { /* u76 */
307 compatible = "ti,ina226";
308 #io-channel-cells = <1>;
309 label = "ina226-u76";
310 reg = <0x40>;
311 shunt-resistor = <5000>;
312 };
313 u77: ina226@41 { /* u77 */
314 compatible = "ti,ina226";
315 #io-channel-cells = <1>;
316 label = "ina226-u77";
317 reg = <0x41>;
318 shunt-resistor = <5000>;
319 };
320 u78: ina226@42 { /* u78 */
321 compatible = "ti,ina226";
322 #io-channel-cells = <1>;
323 label = "ina226-u78";
324 reg = <0x42>;
325 shunt-resistor = <5000>;
326 };
327 u87: ina226@43 { /* u87 */
328 compatible = "ti,ina226";
329 #io-channel-cells = <1>;
330 label = "ina226-u87";
331 reg = <0x43>;
332 shunt-resistor = <5000>;
333 };
334 u85: ina226@44 { /* u85 */
335 compatible = "ti,ina226";
336 #io-channel-cells = <1>;
337 label = "ina226-u85";
338 reg = <0x44>;
339 shunt-resistor = <5000>;
340 };
341 u86: ina226@45 { /* u86 */
342 compatible = "ti,ina226";
343 #io-channel-cells = <1>;
344 label = "ina226-u86";
345 reg = <0x45>;
346 shunt-resistor = <5000>;
347 };
348 u93: ina226@46 { /* u93 */
349 compatible = "ti,ina226";
350 #io-channel-cells = <1>;
351 label = "ina226-u93";
352 reg = <0x46>;
353 shunt-resistor = <5000>;
354 };
355 u88: ina226@47 { /* u88 */
356 compatible = "ti,ina226";
357 #io-channel-cells = <1>;
358 label = "ina226-u88";
359 reg = <0x47>;
360 shunt-resistor = <5000>;
361 };
362 u15: ina226@4a { /* u15 */
363 compatible = "ti,ina226";
364 #io-channel-cells = <1>;
365 label = "ina226-u15";
366 reg = <0x4a>;
367 shunt-resistor = <5000>;
368 };
369 u92: ina226@4b { /* u92 */
370 compatible = "ti,ina226";
371 #io-channel-cells = <1>;
372 label = "ina226-u92";
373 reg = <0x4b>;
374 shunt-resistor = <5000>;
375 };
376 };
377 i2c@1 {
378 #address-cells = <1>;
379 #size-cells = <0>;
380 reg = <1>;
381 /* PL_PMBUS */
382 u79: ina226@40 { /* u79 */
383 compatible = "ti,ina226";
384 #io-channel-cells = <1>;
385 label = "ina226-u79";
386 reg = <0x40>;
387 shunt-resistor = <2000>;
388 };
389 u81: ina226@41 { /* u81 */
390 compatible = "ti,ina226";
391 #io-channel-cells = <1>;
392 label = "ina226-u81";
393 reg = <0x41>;
394 shunt-resistor = <5000>;
395 };
396 u80: ina226@42 { /* u80 */
397 compatible = "ti,ina226";
398 #io-channel-cells = <1>;
399 label = "ina226-u80";
400 reg = <0x42>;
401 shunt-resistor = <5000>;
402 };
403 u84: ina226@43 { /* u84 */
404 compatible = "ti,ina226";
405 #io-channel-cells = <1>;
406 label = "ina226-u84";
407 reg = <0x43>;
408 shunt-resistor = <5000>;
409 };
410 u16: ina226@44 { /* u16 */
411 compatible = "ti,ina226";
412 #io-channel-cells = <1>;
413 label = "ina226-u16";
414 reg = <0x44>;
415 shunt-resistor = <5000>;
416 };
417 u65: ina226@45 { /* u65 */
418 compatible = "ti,ina226";
419 #io-channel-cells = <1>;
420 label = "ina226-u65";
421 reg = <0x45>;
422 shunt-resistor = <5000>;
423 };
424 u74: ina226@46 { /* u74 */
425 compatible = "ti,ina226";
426 #io-channel-cells = <1>;
427 label = "ina226-u74";
428 reg = <0x46>;
429 shunt-resistor = <5000>;
430 };
431 u75: ina226@47 { /* u75 */
432 compatible = "ti,ina226";
433 #io-channel-cells = <1>;
434 label = "ina226-u75";
435 reg = <0x47>;
436 shunt-resistor = <5000>;
437 };
438 };
439 i2c@2 {
440 #address-cells = <1>;
441 #size-cells = <0>;
442 reg = <2>;
443 /* MAXIM_PMBUS - 00 */
444 max15301@a { /* u46 */
445 compatible = "maxim,max15301";
446 reg = <0xa>;
447 };
448 max15303@b { /* u4 */
449 compatible = "maxim,max15303";
450 reg = <0xb>;
451 };
452 max15303@10 { /* u13 */
453 compatible = "maxim,max15303";
454 reg = <0x10>;
455 };
456 max15301@13 { /* u47 */
457 compatible = "maxim,max15301";
458 reg = <0x13>;
459 };
460 max15303@14 { /* u7 */
461 compatible = "maxim,max15303";
462 reg = <0x14>;
463 };
464 max15303@15 { /* u6 */
465 compatible = "maxim,max15303";
466 reg = <0x15>;
467 };
468 max15303@16 { /* u10 */
469 compatible = "maxim,max15303";
470 reg = <0x16>;
471 };
472 max15303@17 { /* u9 */
473 compatible = "maxim,max15303";
474 reg = <0x17>;
475 };
476 max15301@18 { /* u63 */
477 compatible = "maxim,max15301";
478 reg = <0x18>;
479 };
480 max15303@1a { /* u49 */
481 compatible = "maxim,max15303";
482 reg = <0x1a>;
483 };
484 max15303@1d { /* u18 */
485 compatible = "maxim,max15303";
486 reg = <0x1d>;
487 };
488 max15303@20 { /* u8 */
489 compatible = "maxim,max15303";
490 status = "disabled"; /* unreachable */
491 reg = <0x20>;
492 };
493 max20751@72 { /* u95 */
494 compatible = "maxim,max20751";
495 reg = <0x72>;
496 };
497 max20751@73 { /* u96 */
498 compatible = "maxim,max20751";
499 reg = <0x73>;
500 };
501 };
502 /* Bus 3 is not connected */
503 };
504 };
505
506 &i2c1 {
507 status = "okay";
508 clock-frequency = <400000>;
509 pinctrl-names = "default", "gpio";
510 pinctrl-0 = <&pinctrl_i2c1_default>;
511 pinctrl-1 = <&pinctrl_i2c1_gpio>;
512 scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
513 sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
514
515 /* PL i2c via PCA9306 - u45 */
516 i2c-mux@74 { /* u34 */
517 compatible = "nxp,pca9548";
518 #address-cells = <1>;
519 #size-cells = <0>;
520 reg = <0x74>;
521 i2c@0 {
522 #address-cells = <1>;
523 #size-cells = <0>;
524 reg = <0>;
525 /*
526 * IIC_EEPROM 1kB memory which uses 256B blocks
527 * where every block has different address.
528 * 0 - 256B address 0x54
529 * 256B - 512B address 0x55
530 * 512B - 768B address 0x56
531 * 768B - 1024B address 0x57
532 */
533 eeprom: eeprom@54 { /* u23 */
534 compatible = "atmel,24c08";
535 reg = <0x54>;
536 };
537 };
538 i2c@1 {
539 #address-cells = <1>;
540 #size-cells = <0>;
541 reg = <1>;
542 si5341: clock-generator@36 { /* SI5341 - u69 */
543 compatible = "silabs,si5341";
544 reg = <0x36>;
545 #clock-cells = <2>;
546 #address-cells = <1>;
547 #size-cells = <0>;
548 clocks = <&ref48>;
549 clock-names = "xtal";
550 clock-output-names = "si5341";
551
552 si5341_0: out@0 {
553 /* refclk0 for PS-GT, used for DP */
554 reg = <0>;
555 always-on;
556 };
557 si5341_2: out@2 {
558 /* refclk2 for PS-GT, used for USB3 */
559 reg = <2>;
560 always-on;
561 };
562 si5341_3: out@3 {
563 /* refclk3 for PS-GT, used for SATA */
564 reg = <3>;
565 always-on;
566 };
567 si5341_4: out@4 {
568 /* refclk4 for PS-GT, used for PCIE slot */
569 reg = <4>;
570 always-on;
571 };
572 si5341_5: out@5 {
573 /* refclk5 for PS-GT, used for PCIE */
574 reg = <5>;
575 always-on;
576 };
577 si5341_6: out@6 {
578 /* refclk6 PL CLK125 */
579 reg = <6>;
580 always-on;
581 };
582 si5341_7: out@7 {
583 /* refclk7 PL CLK74 */
584 reg = <7>;
585 always-on;
586 };
587 si5341_9: out@9 {
588 /* refclk9 used for PS_REF_CLK 33.3 MHz */
589 reg = <9>;
590 always-on;
591 };
592 };
593 };
594 i2c@2 {
595 #address-cells = <1>;
596 #size-cells = <0>;
597 reg = <2>;
598 si570_1: clock-generator@5d { /* USER SI570 - u42 */
599 #clock-cells = <0>;
600 compatible = "silabs,si570";
601 reg = <0x5d>;
602 temperature-stability = <50>;
603 factory-fout = <300000000>;
604 clock-frequency = <300000000>;
605 clock-output-names = "si570_user";
606 };
607 };
608 i2c@3 {
609 #address-cells = <1>;
610 #size-cells = <0>;
611 reg = <3>;
612 si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */
613 #clock-cells = <0>;
614 compatible = "silabs,si570";
615 reg = <0x5d>;
616 temperature-stability = <50>; /* copy from zc702 */
617 factory-fout = <156250000>;
618 clock-frequency = <156250000>;
619 clock-output-names = "si570_mgt";
620 };
621 };
622 i2c@4 {
623 #address-cells = <1>;
624 #size-cells = <0>;
625 reg = <4>;
626 /* SI5328 - u20 */
627 };
628 /* 5 - 7 unconnected */
629 };
630
631 i2c-mux@75 {
632 compatible = "nxp,pca9548"; /* u135 */
633 #address-cells = <1>;
634 #size-cells = <0>;
635 reg = <0x75>;
636
637 i2c@0 {
638 #address-cells = <1>;
639 #size-cells = <0>;
640 reg = <0>;
641 /* HPC0_IIC */
642 };
643 i2c@1 {
644 #address-cells = <1>;
645 #size-cells = <0>;
646 reg = <1>;
647 /* HPC1_IIC */
648 };
649 i2c@2 {
650 #address-cells = <1>;
651 #size-cells = <0>;
652 reg = <2>;
653 /* SYSMON */
654 };
655 i2c@3 {
656 #address-cells = <1>;
657 #size-cells = <0>;
658 reg = <3>;
659 /* DDR4 SODIMM */
660 };
661 i2c@4 {
662 #address-cells = <1>;
663 #size-cells = <0>;
664 reg = <4>;
665 /* SEP 3 */
666 };
667 i2c@5 {
668 #address-cells = <1>;
669 #size-cells = <0>;
670 reg = <5>;
671 /* SEP 2 */
672 };
673 i2c@6 {
674 #address-cells = <1>;
675 #size-cells = <0>;
676 reg = <6>;
677 /* SEP 1 */
678 };
679 i2c@7 {
680 #address-cells = <1>;
681 #size-cells = <0>;
682 reg = <7>;
683 /* SEP 0 */
684 };
685 };
686 };
687
688 &pinctrl0 {
689 status = "okay";
690 pinctrl_i2c0_default: i2c0-default {
691 mux {
692 groups = "i2c0_3_grp";
693 function = "i2c0";
694 };
695
696 conf {
697 groups = "i2c0_3_grp";
698 bias-pull-up;
699 slew-rate = <SLEW_RATE_SLOW>;
700 power-source = <IO_STANDARD_LVCMOS18>;
701 };
702 };
703
704 pinctrl_i2c0_gpio: i2c0-gpio-grp {
705 mux {
706 groups = "gpio0_14_grp", "gpio0_15_grp";
707 function = "gpio0";
708 };
709
710 conf {
711 groups = "gpio0_14_grp", "gpio0_15_grp";
712 slew-rate = <SLEW_RATE_SLOW>;
713 power-source = <IO_STANDARD_LVCMOS18>;
714 };
715 };
716
717 pinctrl_i2c1_default: i2c1-default {
718 mux {
719 groups = "i2c1_4_grp";
720 function = "i2c1";
721 };
722
723 conf {
724 groups = "i2c1_4_grp";
725 bias-pull-up;
726 slew-rate = <SLEW_RATE_SLOW>;
727 power-source = <IO_STANDARD_LVCMOS18>;
728 };
729 };
730
731 pinctrl_i2c1_gpio: i2c1-gpio-grp {
732 mux {
733 groups = "gpio0_16_grp", "gpio0_17_grp";
734 function = "gpio0";
735 };
736
737 conf {
738 groups = "gpio0_16_grp", "gpio0_17_grp";
739 slew-rate = <SLEW_RATE_SLOW>;
740 power-source = <IO_STANDARD_LVCMOS18>;
741 };
742 };
743
744 pinctrl_uart0_default: uart0-default {
745 mux {
746 groups = "uart0_4_grp";
747 function = "uart0";
748 };
749
750 conf {
751 groups = "uart0_4_grp";
752 slew-rate = <SLEW_RATE_SLOW>;
753 power-source = <IO_STANDARD_LVCMOS18>;
754 };
755
756 conf-rx {
757 pins = "MIO18";
758 bias-high-impedance;
759 };
760
761 conf-tx {
762 pins = "MIO19";
763 bias-disable;
764 };
765 };
766
767 pinctrl_uart1_default: uart1-default {
768 mux {
769 groups = "uart1_5_grp";
770 function = "uart1";
771 };
772
773 conf {
774 groups = "uart1_5_grp";
775 slew-rate = <SLEW_RATE_SLOW>;
776 power-source = <IO_STANDARD_LVCMOS18>;
777 };
778
779 conf-rx {
780 pins = "MIO21";
781 bias-high-impedance;
782 };
783
784 conf-tx {
785 pins = "MIO20";
786 bias-disable;
787 };
788 };
789
790 pinctrl_usb0_default: usb0-default {
791 mux {
792 groups = "usb0_0_grp";
793 function = "usb0";
794 };
795
796 conf {
797 groups = "usb0_0_grp";
798 power-source = <IO_STANDARD_LVCMOS18>;
799 };
800
801 conf-rx {
802 pins = "MIO52", "MIO53", "MIO55";
803 bias-high-impedance;
804 drive-strength = <12>;
805 slew-rate = <SLEW_RATE_FAST>;
806 };
807
808 conf-tx {
809 pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
810 "MIO60", "MIO61", "MIO62", "MIO63";
811 bias-disable;
812 drive-strength = <4>;
813 slew-rate = <SLEW_RATE_SLOW>;
814 };
815 };
816
817 pinctrl_gem3_default: gem3-default {
818 mux {
819 function = "ethernet3";
820 groups = "ethernet3_0_grp";
821 };
822
823 conf {
824 groups = "ethernet3_0_grp";
825 slew-rate = <SLEW_RATE_SLOW>;
826 power-source = <IO_STANDARD_LVCMOS18>;
827 };
828
829 conf-rx {
830 pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
831 "MIO75";
832 bias-high-impedance;
833 low-power-disable;
834 };
835
836 conf-tx {
837 pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
838 "MIO69";
839 bias-disable;
840 low-power-enable;
841 };
842
843 mux-mdio {
844 function = "mdio3";
845 groups = "mdio3_0_grp";
846 };
847
848 conf-mdio {
849 groups = "mdio3_0_grp";
850 slew-rate = <SLEW_RATE_SLOW>;
851 power-source = <IO_STANDARD_LVCMOS18>;
852 bias-disable;
853 };
854 };
855
856 pinctrl_can1_default: can1-default {
857 mux {
858 function = "can1";
859 groups = "can1_6_grp";
860 };
861
862 conf {
863 groups = "can1_6_grp";
864 slew-rate = <SLEW_RATE_SLOW>;
865 power-source = <IO_STANDARD_LVCMOS18>;
866 };
867
868 conf-rx {
869 pins = "MIO25";
870 bias-high-impedance;
871 };
872
873 conf-tx {
874 pins = "MIO24";
875 bias-disable;
876 };
877 };
878
879 pinctrl_sdhci1_default: sdhci1-default {
880 mux {
881 groups = "sdio1_0_grp";
882 function = "sdio1";
883 };
884
885 conf {
886 groups = "sdio1_0_grp";
887 slew-rate = <SLEW_RATE_SLOW>;
888 power-source = <IO_STANDARD_LVCMOS18>;
889 bias-disable;
890 };
891
892 mux-cd {
893 groups = "sdio1_cd_0_grp";
894 function = "sdio1_cd";
895 };
896
897 conf-cd {
898 groups = "sdio1_cd_0_grp";
899 bias-high-impedance;
900 bias-pull-up;
901 slew-rate = <SLEW_RATE_SLOW>;
902 power-source = <IO_STANDARD_LVCMOS18>;
903 };
904
905 mux-wp {
906 groups = "sdio1_wp_0_grp";
907 function = "sdio1_wp";
908 };
909
910 conf-wp {
911 groups = "sdio1_wp_0_grp";
912 bias-high-impedance;
913 bias-pull-up;
914 slew-rate = <SLEW_RATE_SLOW>;
915 power-source = <IO_STANDARD_LVCMOS18>;
916 };
917 };
918
919 pinctrl_gpio_default: gpio-default {
920 mux-sw {
921 function = "gpio0";
922 groups = "gpio0_22_grp", "gpio0_23_grp";
923 };
924
925 conf-sw {
926 groups = "gpio0_22_grp", "gpio0_23_grp";
927 slew-rate = <SLEW_RATE_SLOW>;
928 power-source = <IO_STANDARD_LVCMOS18>;
929 };
930
931 mux-msp {
932 function = "gpio0";
933 groups = "gpio0_13_grp", "gpio0_38_grp";
934 };
935
936 conf-msp {
937 groups = "gpio0_13_grp", "gpio0_38_grp";
938 slew-rate = <SLEW_RATE_SLOW>;
939 power-source = <IO_STANDARD_LVCMOS18>;
940 };
941
942 conf-pull-up {
943 pins = "MIO22", "MIO23";
944 bias-pull-up;
945 };
946
947 conf-pull-none {
948 pins = "MIO13", "MIO38";
949 bias-disable;
950 };
951 };
952 };
953
954 &pcie {
955 status = "okay";
956 phys = <&psgtr 0 PHY_TYPE_PCIE 0 0>;
957 };
958
959 &psgtr {
960 status = "okay";
961 /* pcie, sata, usb3, dp */
962 clocks = <&si5341 0 5>, <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
963 clock-names = "ref0", "ref1", "ref2", "ref3";
964 };
965
966 &qspi {
967 status = "okay";
968 flash@0 {
969 compatible = "m25p80", "jedec,spi-nor"; /* 16MB + 16MB */
970 #address-cells = <1>;
971 #size-cells = <1>;
972 reg = <0x0>;
973 spi-tx-bus-width = <4>;
974 spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
975 spi-max-frequency = <108000000>; /* Based on DC1 spec */
976 };
977 };
978
979 &rtc {
980 status = "okay";
981 };
982
983 &sata {
984 status = "okay";
985 /* SATA OOB timing settings */
986 ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
987 ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
988 ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
989 ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
990 ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
991 ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
992 ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
993 ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
994 phy-names = "sata-phy";
995 phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
996 };
997
998 /* SD1 with level shifter */
999 &sdhci1 {
1000 status = "okay";
1001 /*
1002 * 1.0 revision has level shifter and this property should be
1003 * removed for supporting UHS mode
1004 */
1005 no-1-8-v;
1006 pinctrl-names = "default";
1007 pinctrl-0 = <&pinctrl_sdhci1_default>;
1008 xlnx,mio-bank = <1>;
1009 };
1010
1011 &uart0 {
1012 status = "okay";
1013 pinctrl-names = "default";
1014 pinctrl-0 = <&pinctrl_uart0_default>;
1015 };
1016
1017 &uart1 {
1018 status = "okay";
1019 pinctrl-names = "default";
1020 pinctrl-0 = <&pinctrl_uart1_default>;
1021 };
1022
1023 /* ULPI SMSC USB3320 */
1024 &usb0 {
1025 status = "okay";
1026 pinctrl-names = "default";
1027 pinctrl-0 = <&pinctrl_usb0_default>;
1028 phy-names = "usb3-phy";
1029 phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
1030 };
1031
1032 &dwc3_0 {
1033 status = "okay";
1034 dr_mode = "host";
1035 snps,usb3_lpm_capable;
1036 maximum-speed = "super-speed";
1037 };
1038
1039 &watchdog0 {
1040 status = "okay";
1041 };
1042
1043 &ams_ps {
1044 status = "okay";
1045 };
1046
1047 &ams_pl {
1048 status = "okay";
1049 };
1050
1051 &zynqmp_dpdma {
1052 status = "okay";
1053 };
1054
1055 &zynqmp_dpsub {
1056 status = "okay";
1057 phy-names = "dp-phy0";
1058 phys = <&psgtr 1 PHY_TYPE_DP 0 3>;
1059 };
1060
1061 &out_dp {
1062 dpsub_dp_out: endpoint {
1063 remote-endpoint = <&dpcon_in>;
1064 };
1065 };