| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* dts file for Xilinx ZynqMP SM-K26 rev2/1/B/A |
| 4 |
* |
| 5 |
* (C) Copyright 2020 - 2021, Xilinx, Inc. |
| 6 |
* (C) Copyright 2023 - 2024, Advanced Micro Devices, Inc. |
| 7 |
* |
| 8 |
* Michal Simek <[email protected]> |
| 9 |
*/ |
| 10 |
|
| 11 |
/dts-v1/; |
| 12 |
|
| 13 |
#include "zynqmp.dtsi" |
| 14 |
#include "zynqmp-clk-ccf.dtsi" |
| 15 |
#include <dt-bindings/input/input.h> |
| 16 |
#include <dt-bindings/gpio/gpio.h> |
| 17 |
#include <dt-bindings/phy/phy.h> |
| 18 |
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h> |
| 19 |
|
| 20 |
/ { |
| 21 |
model = "ZynqMP SM-K26 Rev2/1/B/A"; |
| 22 |
compatible = "xlnx,zynqmp-sm-k26-rev2", |
| 23 |
"xlnx,zynqmp-sm-k26-rev1", "xlnx,zynqmp-sm-k26-revB", |
| 24 |
"xlnx,zynqmp-sm-k26-revA", "xlnx,zynqmp-sm-k26", |
| 25 |
"xlnx,zynqmp"; |
| 26 |
|
| 27 |
aliases { |
| 28 |
i2c0 = &i2c0; |
| 29 |
i2c1 = &i2c1; |
| 30 |
mmc0 = &sdhci0; |
| 31 |
mmc1 = &sdhci1; |
| 32 |
nvmem0 = &eeprom; |
| 33 |
nvmem1 = &eeprom_cc; |
| 34 |
rtc0 = &rtc; |
| 35 |
serial0 = &uart0; |
| 36 |
serial1 = &uart1; |
| 37 |
serial2 = &dcc; |
| 38 |
spi0 = &qspi; |
| 39 |
spi1 = &spi0; |
| 40 |
spi2 = &spi1; |
| 41 |
usb0 = &usb0; |
| 42 |
usb1 = &usb1; |
| 43 |
}; |
| 44 |
|
| 45 |
chosen { |
| 46 |
bootargs = "earlycon"; |
| 47 |
stdout-path = "serial1:115200n8"; |
| 48 |
}; |
| 49 |
|
| 50 |
memory@0 { |
| 51 |
device_type = "memory"; /* 4GB */ |
| 52 |
reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>; |
| 53 |
}; |
| 54 |
|
| 55 |
reserved-memory { |
| 56 |
#address-cells = <2>; |
| 57 |
#size-cells = <2>; |
| 58 |
ranges; |
| 59 |
|
| 60 |
pmu_region: pmu@7ff00000 { |
| 61 |
reg = <0x0 0x7ff00000 0x0 0x100000>; |
| 62 |
no-map; |
| 63 |
}; |
| 64 |
}; |
| 65 |
|
| 66 |
gpio-keys { |
| 67 |
compatible = "gpio-keys"; |
| 68 |
autorepeat; |
| 69 |
key-fwuen { |
| 70 |
label = "fwuen"; |
| 71 |
gpios = <&gpio 12 GPIO_ACTIVE_LOW>; |
| 72 |
linux,code = <BTN_MISC>; |
| 73 |
wakeup-source; |
| 74 |
autorepeat; |
| 75 |
}; |
| 76 |
}; |
| 77 |
|
| 78 |
leds { |
| 79 |
compatible = "gpio-leds"; |
| 80 |
ds35-led { |
| 81 |
label = "heartbeat"; |
| 82 |
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; |
| 83 |
linux,default-trigger = "heartbeat"; |
| 84 |
}; |
| 85 |
|
| 86 |
ds36-led { |
| 87 |
label = "vbus_det"; |
| 88 |
gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; |
| 89 |
default-state = "on"; |
| 90 |
}; |
| 91 |
}; |
| 92 |
|
| 93 |
pwm_fan: pwm-fan { |
| 94 |
compatible = "pwm-fan"; |
| 95 |
status = "okay"; |
| 96 |
pwms = <&ttc0 2 40000 1>; |
| 97 |
}; |
| 98 |
}; |
| 99 |
|
| 100 |
&modepin_gpio { |
| 101 |
label = "modepin"; |
| 102 |
}; |
| 103 |
|
| 104 |
&ttc0 { |
| 105 |
status = "okay"; |
| 106 |
#pwm-cells = <3>; |
| 107 |
}; |
| 108 |
|
| 109 |
&uart1 { /* MIO36/MIO37 */ |
| 110 |
status = "okay"; |
| 111 |
}; |
| 112 |
|
| 113 |
&pinctrl0 { |
| 114 |
status = "okay"; |
| 115 |
pinctrl_sdhci0_default: sdhci0-default { |
| 116 |
conf { |
| 117 |
groups = "sdio0_0_grp"; |
| 118 |
slew-rate = <SLEW_RATE_SLOW>; |
| 119 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 120 |
bias-disable; |
| 121 |
}; |
| 122 |
|
| 123 |
mux { |
| 124 |
groups = "sdio0_0_grp"; |
| 125 |
function = "sdio0"; |
| 126 |
}; |
| 127 |
}; |
| 128 |
}; |
| 129 |
|
| 130 |
&qspi { /* MIO 0-5 - U143 */ |
| 131 |
status = "okay"; |
| 132 |
spi_flash: flash@0 { /* MT25QU512A */ |
| 133 |
compatible = "jedec,spi-nor"; /* 64MB */ |
| 134 |
reg = <0>; |
| 135 |
spi-tx-bus-width = <4>; |
| 136 |
spi-rx-bus-width = <4>; |
| 137 |
spi-max-frequency = <40000000>; /* 40MHz */ |
| 138 |
|
| 139 |
partitions { |
| 140 |
compatible = "fixed-partitions"; |
| 141 |
#address-cells = <1>; |
| 142 |
#size-cells = <1>; |
| 143 |
|
| 144 |
partition@0 { |
| 145 |
label = "Image Selector"; |
| 146 |
reg = <0x0 0x80000>; /* 512KB */ |
| 147 |
read-only; |
| 148 |
lock; |
| 149 |
}; |
| 150 |
partition@80000 { |
| 151 |
label = "Image Selector Golden"; |
| 152 |
reg = <0x80000 0x80000>; /* 512KB */ |
| 153 |
read-only; |
| 154 |
lock; |
| 155 |
}; |
| 156 |
partition@100000 { |
| 157 |
label = "Persistent Register"; |
| 158 |
reg = <0x100000 0x20000>; /* 128KB */ |
| 159 |
}; |
| 160 |
partition@120000 { |
| 161 |
label = "Persistent Register Backup"; |
| 162 |
reg = <0x120000 0x20000>; /* 128KB */ |
| 163 |
}; |
| 164 |
partition@140000 { |
| 165 |
label = "Open_1"; |
| 166 |
reg = <0x140000 0xC0000>; /* 768KB */ |
| 167 |
}; |
| 168 |
partition@200000 { |
| 169 |
label = "Image A (FSBL, PMU, ATF, U-Boot)"; |
| 170 |
reg = <0x200000 0xD00000>; /* 13MB */ |
| 171 |
}; |
| 172 |
partition@f00000 { |
| 173 |
label = "ImgSel Image A Catch"; |
| 174 |
reg = <0xF00000 0x80000>; /* 512KB */ |
| 175 |
read-only; |
| 176 |
lock; |
| 177 |
}; |
| 178 |
partition@f80000 { |
| 179 |
label = "Image B (FSBL, PMU, ATF, U-Boot)"; |
| 180 |
reg = <0xF80000 0xD00000>; /* 13MB */ |
| 181 |
}; |
| 182 |
partition@1c80000 { |
| 183 |
label = "ImgSel Image B Catch"; |
| 184 |
reg = <0x1C80000 0x80000>; /* 512KB */ |
| 185 |
read-only; |
| 186 |
lock; |
| 187 |
}; |
| 188 |
partition@1d00000 { |
| 189 |
label = "Open_2"; |
| 190 |
reg = <0x1D00000 0x100000>; /* 1MB */ |
| 191 |
}; |
| 192 |
partition@1e00000 { |
| 193 |
label = "Recovery Image"; |
| 194 |
reg = <0x1E00000 0x200000>; /* 2MB */ |
| 195 |
read-only; |
| 196 |
lock; |
| 197 |
}; |
| 198 |
partition@2000000 { |
| 199 |
label = "Recovery Image Backup"; |
| 200 |
reg = <0x2000000 0x200000>; /* 2MB */ |
| 201 |
read-only; |
| 202 |
lock; |
| 203 |
}; |
| 204 |
partition@2200000 { |
| 205 |
label = "U-Boot storage variables"; |
| 206 |
reg = <0x2200000 0x20000>; /* 128KB */ |
| 207 |
}; |
| 208 |
partition@2220000 { |
| 209 |
label = "U-Boot storage variables backup"; |
| 210 |
reg = <0x2220000 0x20000>; /* 128KB */ |
| 211 |
}; |
| 212 |
partition@2240000 { |
| 213 |
label = "SHA256"; |
| 214 |
reg = <0x2240000 0x40000>; /* 256B but 256KB sector */ |
| 215 |
read-only; |
| 216 |
lock; |
| 217 |
}; |
| 218 |
partition@2280000 { |
| 219 |
label = "Secure OS Storage"; |
| 220 |
reg = <0x2280000 0x20000>; /* 128KB */ |
| 221 |
}; |
| 222 |
partition@22a0000 { |
| 223 |
label = "User"; |
| 224 |
reg = <0x22a0000 0x1d60000>; /* 29.375 MB */ |
| 225 |
}; |
| 226 |
}; |
| 227 |
}; |
| 228 |
}; |
| 229 |
|
| 230 |
&sdhci0 { /* MIO13-23 - 16GB emmc MTFC16GAPALBH-IT - U133A */ |
| 231 |
status = "okay"; |
| 232 |
pinctrl-names = "default"; |
| 233 |
pinctrl-0 = <&pinctrl_sdhci0_default>; |
| 234 |
non-removable; |
| 235 |
disable-wp; |
| 236 |
no-sd; |
| 237 |
no-sdio; |
| 238 |
cap-mmc-hw-reset; |
| 239 |
bus-width = <8>; |
| 240 |
xlnx,mio-bank = <0>; |
| 241 |
assigned-clock-rates = <187498123>; |
| 242 |
}; |
| 243 |
|
| 244 |
&spi1 { /* MIO6, 9-11 */ |
| 245 |
status = "okay"; |
| 246 |
label = "TPM"; |
| 247 |
num-cs = <1>; |
| 248 |
tpm@0 { /* slm9670 - U144 */ |
| 249 |
compatible = "infineon,slb9670", "tcg,tpm_tis-spi"; |
| 250 |
reg = <0>; |
| 251 |
spi-max-frequency = <18500000>; |
| 252 |
}; |
| 253 |
}; |
| 254 |
|
| 255 |
&i2c1 { |
| 256 |
status = "okay"; |
| 257 |
bootph-all; |
| 258 |
clock-frequency = <400000>; |
| 259 |
scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 260 |
sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 261 |
|
| 262 |
eeprom: eeprom@50 { /* u46 - also at address 0x58 */ |
| 263 |
bootph-all; |
| 264 |
compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */ |
| 265 |
reg = <0x50>; |
| 266 |
/* WP pin EE_WP_EN connected to slg7x644092@68 */ |
| 267 |
}; |
| 268 |
|
| 269 |
eeprom_cc: eeprom@51 { /* required by spec - also at address 0x59 */ |
| 270 |
bootph-all; |
| 271 |
compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */ |
| 272 |
reg = <0x51>; |
| 273 |
}; |
| 274 |
|
| 275 |
/* da9062@30 - u170 - also at address 0x31 */ |
| 276 |
/* da9131@33 - u167 */ |
| 277 |
da9131: pmic@33 { |
| 278 |
compatible = "dlg,da9131"; |
| 279 |
reg = <0x33>; |
| 280 |
regulators { |
| 281 |
da9131_buck1: buck1 { |
| 282 |
regulator-name = "da9131_buck1"; |
| 283 |
regulator-boot-on; |
| 284 |
regulator-always-on; |
| 285 |
}; |
| 286 |
da9131_buck2: buck2 { |
| 287 |
regulator-name = "da9131_buck2"; |
| 288 |
regulator-boot-on; |
| 289 |
regulator-always-on; |
| 290 |
}; |
| 291 |
}; |
| 292 |
}; |
| 293 |
|
| 294 |
/* da9130@32 - u166 */ |
| 295 |
da9130: pmic@32 { |
| 296 |
compatible = "dlg,da9130"; |
| 297 |
reg = <0x32>; |
| 298 |
regulators { |
| 299 |
da9130_buck1: buck1 { |
| 300 |
regulator-name = "da9130_buck1"; |
| 301 |
regulator-boot-on; |
| 302 |
regulator-always-on; |
| 303 |
}; |
| 304 |
}; |
| 305 |
}; |
| 306 |
|
| 307 |
/* slg7x644091@70 - u168 NOT accessible due to address conflict with stdp4320 */ |
| 308 |
/* |
| 309 |
* stdp4320 - u27 FW has below two issues to be fixed in next board revision. |
| 310 |
* Device acknowledging to addresses 0x5C, 0x5D, 0x70, 0x72, 0x76. |
| 311 |
* Address conflict with slg7x644091@70 making both the devices NOT accessible. |
| 312 |
* With the FW fix, stdp4320 should respond to address 0x73 only. |
| 313 |
*/ |
| 314 |
/* slg7x644092@68 - u169 */ |
| 315 |
/* Also connected via JA1C as C23/C24 */ |
| 316 |
}; |
| 317 |
|
| 318 |
&gpio { |
| 319 |
status = "okay"; |
| 320 |
gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */ |
| 321 |
"QSPI_CS_B", "SPI_CLK", "LED1", "LED2", "SPI_CS_B", /* 5 - 9 */ |
| 322 |
"SPI_MISO", "SPI_MOSI", "FWUEN", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */ |
| 323 |
"EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */ |
| 324 |
"EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST", "I2C1_SCL", /* 20 - 24 */ |
| 325 |
"I2C1_SDA", "", "", "", "", /* 25 - 29 */ |
| 326 |
"", "", "", "", "", /* 30 - 34 */ |
| 327 |
"", "", "", "", "", /* 35 - 39 */ |
| 328 |
"", "", "", "", "", /* 40 - 44 */ |
| 329 |
"", "", "", "", "", /* 45 - 49 */ |
| 330 |
"", "", "", "", "", /* 50 - 54 */ |
| 331 |
"", "", "", "", "", /* 55 - 59 */ |
| 332 |
"", "", "", "", "", /* 60 - 64 */ |
| 333 |
"", "", "", "", "", /* 65 - 69 */ |
| 334 |
"", "", "", "", "", /* 70 - 74 */ |
| 335 |
"", "", "", /* 75 - 77, MIO end and EMIO start */ |
| 336 |
"", "", /* 78 - 79 */ |
| 337 |
"", "", "", "", "", /* 80 - 84 */ |
| 338 |
"", "", "", "", "", /* 85 - 89 */ |
| 339 |
"", "", "", "", "", /* 90 - 94 */ |
| 340 |
"", "", "", "", "", /* 95 - 99 */ |
| 341 |
"", "", "", "", "", /* 100 - 104 */ |
| 342 |
"", "", "", "", "", /* 105 - 109 */ |
| 343 |
"", "", "", "", "", /* 110 - 114 */ |
| 344 |
"", "", "", "", "", /* 115 - 119 */ |
| 345 |
"", "", "", "", "", /* 120 - 124 */ |
| 346 |
"", "", "", "", "", /* 125 - 129 */ |
| 347 |
"", "", "", "", "", /* 130 - 134 */ |
| 348 |
"", "", "", "", "", /* 135 - 139 */ |
| 349 |
"", "", "", "", "", /* 140 - 144 */ |
| 350 |
"", "", "", "", "", /* 145 - 149 */ |
| 351 |
"", "", "", "", "", /* 150 - 154 */ |
| 352 |
"", "", "", "", "", /* 155 - 159 */ |
| 353 |
"", "", "", "", "", /* 160 - 164 */ |
| 354 |
"", "", "", "", "", /* 165 - 169 */ |
| 355 |
"", "", "", ""; /* 170 - 173 */ |
| 356 |
}; |
| 357 |
|
| 358 |
&ams_ps { |
| 359 |
status = "okay"; |
| 360 |
}; |
| 361 |
|
| 362 |
&ams_pl { |
| 363 |
status = "okay"; |
| 364 |
}; |
| 365 |
|
| 366 |
&zynqmp_dpsub { |
| 367 |
status = "okay"; |
| 368 |
}; |
| 369 |
|
| 370 |
&rtc { |
| 371 |
status = "okay"; |
| 372 |
}; |
| 373 |
|
| 374 |
&lpd_dma_chan1 { |
| 375 |
status = "okay"; |
| 376 |
}; |
| 377 |
|
| 378 |
&lpd_dma_chan2 { |
| 379 |
status = "okay"; |
| 380 |
}; |
| 381 |
|
| 382 |
&lpd_dma_chan3 { |
| 383 |
status = "okay"; |
| 384 |
}; |
| 385 |
|
| 386 |
&lpd_dma_chan4 { |
| 387 |
status = "okay"; |
| 388 |
}; |
| 389 |
|
| 390 |
&lpd_dma_chan5 { |
| 391 |
status = "okay"; |
| 392 |
}; |
| 393 |
|
| 394 |
&lpd_dma_chan6 { |
| 395 |
status = "okay"; |
| 396 |
}; |
| 397 |
|
| 398 |
&lpd_dma_chan7 { |
| 399 |
status = "okay"; |
| 400 |
}; |
| 401 |
|
| 402 |
&lpd_dma_chan8 { |
| 403 |
status = "okay"; |
| 404 |
}; |
| 405 |
|
| 406 |
&fpd_dma_chan1 { |
| 407 |
status = "okay"; |
| 408 |
}; |
| 409 |
|
| 410 |
&fpd_dma_chan2 { |
| 411 |
status = "okay"; |
| 412 |
}; |
| 413 |
|
| 414 |
&fpd_dma_chan3 { |
| 415 |
status = "okay"; |
| 416 |
}; |
| 417 |
|
| 418 |
&fpd_dma_chan4 { |
| 419 |
status = "okay"; |
| 420 |
}; |
| 421 |
|
| 422 |
&fpd_dma_chan5 { |
| 423 |
status = "okay"; |
| 424 |
}; |
| 425 |
|
| 426 |
&fpd_dma_chan6 { |
| 427 |
status = "okay"; |
| 428 |
}; |
| 429 |
|
| 430 |
&fpd_dma_chan7 { |
| 431 |
status = "okay"; |
| 432 |
}; |
| 433 |
|
| 434 |
&fpd_dma_chan8 { |
| 435 |
status = "okay"; |
| 436 |
}; |
| 437 |
|
| 438 |
&gpu { |
| 439 |
status = "okay"; |
| 440 |
}; |
| 441 |
|
| 442 |
&lpd_watchdog { |
| 443 |
status = "okay"; |
| 444 |
}; |
| 445 |
|
| 446 |
&watchdog0 { |
| 447 |
status = "okay"; |
| 448 |
}; |
| 449 |
|
| 450 |
&cpu_opp_table { |
| 451 |
opp00 { |
| 452 |
opp-hz = /bits/ 64 <1333333333>; |
| 453 |
}; |
| 454 |
opp01 { |
| 455 |
opp-hz = /bits/ 64 <666666666>; |
| 456 |
}; |
| 457 |
opp02 { |
| 458 |
opp-hz = /bits/ 64 <444444444>; |
| 459 |
}; |
| 460 |
opp03 { |
| 461 |
opp-hz = /bits/ 64 <333333333>; |
| 462 |
}; |
| 463 |
}; |