| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* dts file for KV260 revA Carrier Card |
| 4 |
* |
| 5 |
* (C) Copyright 2020 - 2022, Xilinx, Inc. |
| 6 |
* (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. |
| 7 |
* |
| 8 |
* SD level shifter: |
| 9 |
* "A" - A01 board un-modified (NXP) |
| 10 |
* "Y" - A01 board modified with legacy interposer (Nexperia) |
| 11 |
* "Z" - A01 board modified with Diode interposer |
| 12 |
* |
| 13 |
* Michal Simek <[email protected]> |
| 14 |
*/ |
| 15 |
|
| 16 |
#include <dt-bindings/gpio/gpio.h> |
| 17 |
#include <dt-bindings/net/ti-dp83867.h> |
| 18 |
#include <dt-bindings/phy/phy.h> |
| 19 |
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h> |
| 20 |
|
| 21 |
/dts-v1/; |
| 22 |
/plugin/; |
| 23 |
|
| 24 |
&{/} { |
| 25 |
compatible = "xlnx,zynqmp-sk-kv260-revA", |
| 26 |
"xlnx,zynqmp-sk-kv260-revY", |
| 27 |
"xlnx,zynqmp-sk-kv260-revZ", |
| 28 |
"xlnx,zynqmp-sk-kv260", "xlnx,zynqmp"; |
| 29 |
model = "ZynqMP KV260 revA"; |
| 30 |
|
| 31 |
aliases { |
| 32 |
ethernet0 = "/axi/ethernet@ff0e0000"; /* &gem3 */ |
| 33 |
}; |
| 34 |
|
| 35 |
si5332_0: si5332-0 { /* u17 */ |
| 36 |
compatible = "fixed-clock"; |
| 37 |
#clock-cells = <0>; |
| 38 |
clock-frequency = <125000000>; |
| 39 |
}; |
| 40 |
|
| 41 |
si5332_1: si5332-1 { /* u17 */ |
| 42 |
compatible = "fixed-clock"; |
| 43 |
#clock-cells = <0>; |
| 44 |
clock-frequency = <25000000>; |
| 45 |
}; |
| 46 |
|
| 47 |
si5332_2: si5332-2 { /* u17 */ |
| 48 |
compatible = "fixed-clock"; |
| 49 |
#clock-cells = <0>; |
| 50 |
clock-frequency = <48000000>; |
| 51 |
}; |
| 52 |
|
| 53 |
si5332_3: si5332-3 { /* u17 */ |
| 54 |
compatible = "fixed-clock"; |
| 55 |
#clock-cells = <0>; |
| 56 |
clock-frequency = <24000000>; |
| 57 |
}; |
| 58 |
|
| 59 |
si5332_4: si5332-4 { /* u17 */ |
| 60 |
compatible = "fixed-clock"; |
| 61 |
#clock-cells = <0>; |
| 62 |
clock-frequency = <26000000>; |
| 63 |
}; |
| 64 |
|
| 65 |
si5332_5: si5332-5 { /* u17 */ |
| 66 |
compatible = "fixed-clock"; |
| 67 |
#clock-cells = <0>; |
| 68 |
clock-frequency = <27000000>; |
| 69 |
}; |
| 70 |
dpcon { |
| 71 |
compatible = "dp-connector"; |
| 72 |
label = "P11"; |
| 73 |
type = "full-size"; |
| 74 |
|
| 75 |
port { |
| 76 |
dpcon_in: endpoint { |
| 77 |
remote-endpoint = <&dpsub_dp_out>; |
| 78 |
}; |
| 79 |
}; |
| 80 |
}; |
| 81 |
}; |
| 82 |
|
| 83 |
&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */ |
| 84 |
#address-cells = <1>; |
| 85 |
#size-cells = <0>; |
| 86 |
pinctrl-names = "default", "gpio"; |
| 87 |
pinctrl-0 = <&pinctrl_i2c1_default>; |
| 88 |
pinctrl-1 = <&pinctrl_i2c1_gpio>; |
| 89 |
scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 90 |
sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 91 |
|
| 92 |
u14: ina260@40 { /* u14 */ |
| 93 |
compatible = "ti,ina260"; |
| 94 |
label = "ina260-u14"; |
| 95 |
reg = <0x40>; |
| 96 |
}; |
| 97 |
/* u27 - 0xe0 - STDP4320 DP/HDMI splitter */ |
| 98 |
}; |
| 99 |
|
| 100 |
/* DP/USB 3.0 and SATA */ |
| 101 |
&psgtr { |
| 102 |
status = "okay"; |
| 103 |
/* pcie, usb3, sata */ |
| 104 |
clocks = <&si5332_5>, <&si5332_4>, <&si5332_0>; |
| 105 |
clock-names = "ref0", "ref1", "ref2"; |
| 106 |
}; |
| 107 |
|
| 108 |
&sata { |
| 109 |
status = "okay"; |
| 110 |
/* SATA OOB timing settings */ |
| 111 |
ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; |
| 112 |
ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; |
| 113 |
ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; |
| 114 |
ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>; |
| 115 |
ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; |
| 116 |
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; |
| 117 |
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; |
| 118 |
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; |
| 119 |
phy-names = "sata-phy"; |
| 120 |
phys = <&psgtr 3 PHY_TYPE_SATA 1 2>; |
| 121 |
}; |
| 122 |
|
| 123 |
&zynqmp_dpsub { |
| 124 |
status = "okay"; |
| 125 |
phy-names = "dp-phy0", "dp-phy1"; |
| 126 |
phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>; |
| 127 |
assigned-clock-rates = <27000000>, <25000000>, <300000000>; |
| 128 |
}; |
| 129 |
|
| 130 |
&out_dp { |
| 131 |
dpsub_dp_out: endpoint { |
| 132 |
remote-endpoint = <&dpcon_in>; |
| 133 |
}; |
| 134 |
}; |
| 135 |
|
| 136 |
&zynqmp_dpdma { |
| 137 |
status = "okay"; |
| 138 |
assigned-clock-rates = <600000000>; |
| 139 |
}; |
| 140 |
|
| 141 |
&usb0 { |
| 142 |
status = "okay"; |
| 143 |
pinctrl-names = "default"; |
| 144 |
pinctrl-0 = <&pinctrl_usb0_default>; |
| 145 |
phy-names = "usb3-phy"; |
| 146 |
phys = <&psgtr 2 PHY_TYPE_USB3 0 1>; |
| 147 |
}; |
| 148 |
|
| 149 |
&dwc3_0 { |
| 150 |
status = "okay"; |
| 151 |
dr_mode = "host"; |
| 152 |
snps,usb3_lpm_capable; |
| 153 |
maximum-speed = "super-speed"; |
| 154 |
#address-cells = <1>; |
| 155 |
#size-cells = <0>; |
| 156 |
|
| 157 |
/* 2.0 hub on port 1 */ |
| 158 |
hub_2_0: hub@1 { |
| 159 |
compatible = "usb424,2744"; |
| 160 |
reg = <1>; |
| 161 |
peer-hub = <&hub_3_0>; |
| 162 |
reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>; |
| 163 |
}; |
| 164 |
|
| 165 |
/* 3.0 hub on port 2 */ |
| 166 |
hub_3_0: hub@2 { |
| 167 |
compatible = "usb424,5744"; |
| 168 |
reg = <2>; |
| 169 |
peer-hub = <&hub_2_0>; |
| 170 |
reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>; |
| 171 |
}; |
| 172 |
}; |
| 173 |
|
| 174 |
&sdhci1 { /* on CC with tuned parameters */ |
| 175 |
status = "okay"; |
| 176 |
pinctrl-names = "default"; |
| 177 |
pinctrl-0 = <&pinctrl_sdhci1_default>; |
| 178 |
/* |
| 179 |
* SD 3.0 requires level shifter and this property |
| 180 |
* should be removed if the board has level shifter and |
| 181 |
* need to work in UHS mode |
| 182 |
*/ |
| 183 |
no-1-8-v; |
| 184 |
disable-wp; |
| 185 |
xlnx,mio-bank = <1>; |
| 186 |
assigned-clock-rates = <187498123>; |
| 187 |
bus-width = <4>; |
| 188 |
}; |
| 189 |
|
| 190 |
&gem3 { |
| 191 |
status = "okay"; |
| 192 |
pinctrl-names = "default"; |
| 193 |
pinctrl-0 = <&pinctrl_gem3_default>; |
| 194 |
phy-handle = <&phy0>; |
| 195 |
phy-mode = "rgmii-id"; |
| 196 |
assigned-clock-rates = <250000000>; |
| 197 |
|
| 198 |
mdio: mdio { |
| 199 |
#address-cells = <1>; |
| 200 |
#size-cells = <0>; |
| 201 |
|
| 202 |
phy0: ethernet-phy@1 { |
| 203 |
#phy-cells = <1>; |
| 204 |
reg = <1>; |
| 205 |
compatible = "ethernet-phy-id2000.a231"; |
| 206 |
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; |
| 207 |
ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; |
| 208 |
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; |
| 209 |
ti,dp83867-rxctrl-strap-quirk; |
| 210 |
reset-assert-us = <100>; |
| 211 |
reset-deassert-us = <280>; |
| 212 |
reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>; |
| 213 |
}; |
| 214 |
}; |
| 215 |
}; |
| 216 |
|
| 217 |
&pinctrl0 { |
| 218 |
status = "okay"; |
| 219 |
|
| 220 |
pinctrl_gpio0_default: gpio0-default { |
| 221 |
conf { |
| 222 |
groups = "gpio0_38_grp"; |
| 223 |
bias-pull-up; |
| 224 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 225 |
}; |
| 226 |
|
| 227 |
mux { |
| 228 |
groups = "gpio0_38_grp"; |
| 229 |
function = "gpio0"; |
| 230 |
}; |
| 231 |
|
| 232 |
conf-tx { |
| 233 |
pins = "MIO38"; |
| 234 |
bias-disable; |
| 235 |
output-enable; |
| 236 |
}; |
| 237 |
}; |
| 238 |
|
| 239 |
pinctrl_uart1_default: uart1-default { |
| 240 |
conf { |
| 241 |
groups = "uart1_9_grp"; |
| 242 |
slew-rate = <SLEW_RATE_SLOW>; |
| 243 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 244 |
drive-strength = <12>; |
| 245 |
}; |
| 246 |
|
| 247 |
conf-rx { |
| 248 |
pins = "MIO37"; |
| 249 |
bias-high-impedance; |
| 250 |
}; |
| 251 |
|
| 252 |
conf-tx { |
| 253 |
pins = "MIO36"; |
| 254 |
bias-disable; |
| 255 |
output-enable; |
| 256 |
}; |
| 257 |
|
| 258 |
mux { |
| 259 |
groups = "uart1_9_grp"; |
| 260 |
function = "uart1"; |
| 261 |
}; |
| 262 |
}; |
| 263 |
|
| 264 |
pinctrl_i2c1_default: i2c1-default { |
| 265 |
conf { |
| 266 |
groups = "i2c1_6_grp"; |
| 267 |
bias-pull-up; |
| 268 |
slew-rate = <SLEW_RATE_SLOW>; |
| 269 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 270 |
}; |
| 271 |
|
| 272 |
mux { |
| 273 |
groups = "i2c1_6_grp"; |
| 274 |
function = "i2c1"; |
| 275 |
}; |
| 276 |
}; |
| 277 |
|
| 278 |
pinctrl_i2c1_gpio: i2c1-gpio-grp { |
| 279 |
conf { |
| 280 |
groups = "gpio0_24_grp", "gpio0_25_grp"; |
| 281 |
slew-rate = <SLEW_RATE_SLOW>; |
| 282 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 283 |
}; |
| 284 |
|
| 285 |
mux { |
| 286 |
groups = "gpio0_24_grp", "gpio0_25_grp"; |
| 287 |
function = "gpio0"; |
| 288 |
}; |
| 289 |
}; |
| 290 |
|
| 291 |
pinctrl_gem3_default: gem3-default { |
| 292 |
conf { |
| 293 |
groups = "ethernet3_0_grp"; |
| 294 |
slew-rate = <SLEW_RATE_SLOW>; |
| 295 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 296 |
}; |
| 297 |
|
| 298 |
conf-rx { |
| 299 |
pins = "MIO70", "MIO72", "MIO74"; |
| 300 |
bias-high-impedance; |
| 301 |
low-power-disable; |
| 302 |
}; |
| 303 |
|
| 304 |
conf-bootstrap { |
| 305 |
pins = "MIO71", "MIO73", "MIO75"; |
| 306 |
bias-disable; |
| 307 |
output-enable; |
| 308 |
low-power-disable; |
| 309 |
}; |
| 310 |
|
| 311 |
conf-tx { |
| 312 |
pins = "MIO64", "MIO65", "MIO66", |
| 313 |
"MIO67", "MIO68", "MIO69"; |
| 314 |
bias-disable; |
| 315 |
output-enable; |
| 316 |
low-power-enable; |
| 317 |
}; |
| 318 |
|
| 319 |
conf-mdio { |
| 320 |
groups = "mdio3_0_grp"; |
| 321 |
slew-rate = <SLEW_RATE_SLOW>; |
| 322 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 323 |
bias-disable; |
| 324 |
output-enable; |
| 325 |
}; |
| 326 |
|
| 327 |
mux-mdio { |
| 328 |
function = "mdio3"; |
| 329 |
groups = "mdio3_0_grp"; |
| 330 |
}; |
| 331 |
|
| 332 |
mux { |
| 333 |
function = "ethernet3"; |
| 334 |
groups = "ethernet3_0_grp"; |
| 335 |
}; |
| 336 |
}; |
| 337 |
|
| 338 |
pinctrl_usb0_default: usb0-default { |
| 339 |
conf { |
| 340 |
groups = "usb0_0_grp"; |
| 341 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 342 |
}; |
| 343 |
|
| 344 |
conf-rx { |
| 345 |
pins = "MIO52", "MIO53", "MIO55"; |
| 346 |
bias-high-impedance; |
| 347 |
drive-strength = <12>; |
| 348 |
slew-rate = <SLEW_RATE_FAST>; |
| 349 |
}; |
| 350 |
|
| 351 |
conf-tx { |
| 352 |
pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", |
| 353 |
"MIO60", "MIO61", "MIO62", "MIO63"; |
| 354 |
bias-disable; |
| 355 |
output-enable; |
| 356 |
drive-strength = <4>; |
| 357 |
slew-rate = <SLEW_RATE_SLOW>; |
| 358 |
}; |
| 359 |
|
| 360 |
mux { |
| 361 |
groups = "usb0_0_grp"; |
| 362 |
function = "usb0"; |
| 363 |
}; |
| 364 |
}; |
| 365 |
|
| 366 |
pinctrl_sdhci1_default: sdhci1-default { |
| 367 |
conf { |
| 368 |
groups = "sdio1_0_grp"; |
| 369 |
slew-rate = <SLEW_RATE_SLOW>; |
| 370 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 371 |
bias-disable; |
| 372 |
output-enable; |
| 373 |
}; |
| 374 |
|
| 375 |
conf-cd { |
| 376 |
groups = "sdio1_cd_0_grp"; |
| 377 |
bias-high-impedance; |
| 378 |
bias-pull-up; |
| 379 |
slew-rate = <SLEW_RATE_SLOW>; |
| 380 |
power-source = <IO_STANDARD_LVCMOS18>; |
| 381 |
}; |
| 382 |
|
| 383 |
mux-cd { |
| 384 |
groups = "sdio1_cd_0_grp"; |
| 385 |
function = "sdio1_cd"; |
| 386 |
}; |
| 387 |
|
| 388 |
mux { |
| 389 |
groups = "sdio1_0_grp"; |
| 390 |
function = "sdio1"; |
| 391 |
}; |
| 392 |
}; |
| 393 |
}; |
| 394 |
|
| 395 |
&gpio { |
| 396 |
status = "okay"; |
| 397 |
pinctrl-names = "default"; |
| 398 |
pinctrl-0 = <&pinctrl_gpio0_default>; |
| 399 |
}; |
| 400 |
|
| 401 |
&uart1 { |
| 402 |
status = "okay"; |
| 403 |
pinctrl-names = "default"; |
| 404 |
pinctrl-0 = <&pinctrl_uart1_default>; |
| 405 |
}; |