Debian Codegraph @

scripts/dtc/include-prefixes/arm64/ti/k3-j7200-som-p0.dtsi

raw
1 // SPDX-License-Identifier: GPL-2.0-only OR MIT
2 /*
3 * Copyright (C) 2020-2024 Texas Instruments Incorporated - https://www.ti.com/
4 */
5
6 /dts-v1/;
7
8 #include <dt-bindings/gpio/gpio.h>
9
10 #include "k3-j7200.dtsi"
11
12 / {
13 memory@80000000 {
14 device_type = "memory";
15 bootph-all;
16 /* 4G RAM */
17 reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
18 <0x00000008 0x80000000 0x00000000 0x80000000>;
19 };
20
21 reserved_memory: reserved-memory {
22 #address-cells = <2>;
23 #size-cells = <2>;
24 ranges;
25
26 secure_ddr: optee@9e800000 {
27 reg = <0x00 0x9e800000 0x00 0x01800000>;
28 alignment = <0x1000>;
29 no-map;
30 };
31
32 mcu_r5fss0_core0_dma_memory_region: memory@a0000000 {
33 compatible = "shared-dma-pool";
34 reg = <0x00 0xa0000000 0x00 0x100000>;
35 no-map;
36 };
37
38 mcu_r5fss0_core0_memory_region: memory@a0100000 {
39 compatible = "shared-dma-pool";
40 reg = <0x00 0xa0100000 0x00 0xf00000>;
41 no-map;
42 };
43 };
44
45 mux0: mux-controller-0 {
46 compatible = "gpio-mux";
47 #mux-state-cells = <1>;
48 mux-gpios = <&exp_som 1 GPIO_ACTIVE_HIGH>;
49 };
50
51 mux1: mux-controller-1 {
52 compatible = "gpio-mux";
53 #mux-state-cells = <1>;
54 mux-gpios = <&exp_som 2 GPIO_ACTIVE_HIGH>;
55 };
56
57 transceiver0: can-phy0 {
58 /* standby pin has been grounded by default */
59 compatible = "ti,tcan1042";
60 #phy-cells = <0>;
61 max-bitrate = <5000000>;
62 };
63 };
64
65 &wkup_pmx0 {
66 mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-default-pins {
67 pinctrl-single,pins = <
68 J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 1) /* (B6) MCU_OSPI0_CLK.MCU_HYPERBUS0_CK */
69 J721E_WKUP_IOPAD(0x4, PIN_OUTPUT, 1) /* (C8) MCU_OSPI0_LBCLKO.MCU_HYPERBUS0_CKn */
70 J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 1) /* (D6) MCU_OSPI0_CSn0.MCU_HYPERBUS0_CSn0 */
71 J721E_WKUP_IOPAD(0x30, PIN_OUTPUT, 1) /* (D7) MCU_OSPI0_CSn1.MCU_HYPERBUS0_RESETn */
72 J721E_WKUP_IOPAD(0x8, PIN_INPUT, 1) /* (B7) MCU_OSPI0_DQS.MCU_HYPERBUS0_RWDS */
73 J721E_WKUP_IOPAD(0xc, PIN_INPUT, 1) /* (D8) MCU_OSPI0_D0.MCU_HYPERBUS0_DQ0 */
74 J721E_WKUP_IOPAD(0x10, PIN_INPUT, 1) /* (C7) MCU_OSPI0_D1.MCU_HYPERBUS0_DQ1 */
75 J721E_WKUP_IOPAD(0x14, PIN_INPUT, 1) /* (C5) MCU_OSPI0_D2.MCU_HYPERBUS0_DQ2 */
76 J721E_WKUP_IOPAD(0x18, PIN_INPUT, 1) /* (A5) MCU_OSPI0_D3.MCU_HYPERBUS0_DQ3 */
77 J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 1) /* (A6) MCU_OSPI0_D4.MCU_HYPERBUS0_DQ4 */
78 J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (B8) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */
79 J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
80 J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
81 >;
82 bootph-all;
83 };
84
85 mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
86 pinctrl-single,pins = <
87 J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
88 J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */
89 J721E_WKUP_IOPAD(0x000c, PIN_INPUT, 0) /* MCU_OSPI0_D0 */
90 J721E_WKUP_IOPAD(0x0010, PIN_INPUT, 0) /* MCU_OSPI0_D1 */
91 J721E_WKUP_IOPAD(0x0014, PIN_INPUT, 0) /* MCU_OSPI0_D2 */
92 J721E_WKUP_IOPAD(0x0018, PIN_INPUT, 0) /* MCU_OSPI0_D3 */
93 J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_OSPI0_D4 */
94 J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_OSPI0_D5 */
95 J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */
96 J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */
97 J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* MCU_OSPI0_DQS */
98 >;
99 bootph-all;
100 };
101 };
102
103 &wkup_pmx2 {
104 wkup_i2c0_pins_default: wkup-i2c0-default-pins {
105 pinctrl-single,pins = <
106 J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */
107 J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
108 >;
109 bootph-all;
110 };
111 };
112
113 &wkup_pmx3 {
114 pmic_irq_pins_default: pmic-irq-default-pins {
115 pinctrl-single,pins = <
116 J721E_WKUP_IOPAD(0x01c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
117 >;
118 };
119 };
120
121 &main_pmx0 {
122 main_i2c0_pins_default: main-i2c0-default-pins {
123 pinctrl-single,pins = <
124 J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
125 J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
126 >;
127 };
128
129 main_mcan0_pins_default: main-mcan0-default-pins {
130 pinctrl-single,pins = <
131 J721E_IOPAD(0x24, PIN_INPUT, 0) /* (V20) MCAN0_RX */
132 J721E_IOPAD(0x20, PIN_OUTPUT, 0) /* (V18) MCAN0_TX */
133 >;
134 };
135 };
136
137 &hbmc {
138 /* OSPI and HBMC are muxed inside FSS, Bootloader will enable
139 * appropriate node based on board detection
140 */
141 status = "disabled";
142 pinctrl-names = "default";
143 pinctrl-0 = <&mcu_fss0_hpb0_pins_default>;
144 ranges = <0x00 0x00 0x05 0x00000000 0x4000000>, /* 64MB Flash on CS0 */
145 <0x01 0x00 0x05 0x04000000 0x800000>; /* 8MB RAM on CS1 */
146
147 flash@0,0 {
148 compatible = "cypress,hyperflash", "cfi-flash";
149 reg = <0x00 0x00 0x4000000>;
150 bootph-all;
151
152 partitions {
153 compatible = "fixed-partitions";
154 #address-cells = <1>;
155 #size-cells = <1>;
156
157 partition@0 {
158 label = "hbmc.tiboot3";
159 reg = <0x0 0x100000>;
160 };
161
162 partition@100000 {
163 label = "hbmc.tispl";
164 reg = <0x100000 0x200000>;
165 };
166
167 partition@300000 {
168 label = "hbmc.u-boot";
169 reg = <0x300000 0x400000>;
170 };
171
172 partition@700000 {
173 label = "hbmc.env";
174 reg = <0x700000 0x40000>;
175 };
176
177 partition@800000 {
178 label = "hbmc.rootfs";
179 reg = <0x800000 0x3800000>;
180 };
181 };
182 };
183 };
184
185 &main_i2c0 {
186 pinctrl-names = "default";
187 pinctrl-0 = <&main_i2c0_pins_default>;
188 clock-frequency = <400000>;
189
190 exp_som: gpio@21 {
191 compatible = "ti,tca6408";
192 reg = <0x21>;
193 gpio-controller;
194 #gpio-cells = <2>;
195 gpio-line-names = "USB2.0_MUX_SEL", "CANUART_MUX1_SEL0",
196 "CANUART_MUX2_SEL0", "CANUART_MUX_SEL1",
197 "UART/LIN_MUX_SEL", "TRC_D17/AUDIO_REFCLK_SEL",
198 "GPIO_LIN_EN", "CAN_STB";
199 };
200 };
201
202 &wkup_i2c0 {
203 status = "okay";
204 pinctrl-names = "default";
205 pinctrl-0 = <&wkup_i2c0_pins_default>;
206 clock-frequency = <400000>;
207
208 eeprom@50 {
209 compatible = "atmel,24c256";
210 reg = <0x50>;
211 };
212
213 tps659414: pmic@48 {
214 compatible = "ti,tps6594-q1";
215 reg = <0x48>;
216 system-power-controller;
217 pinctrl-names = "default";
218 pinctrl-0 = <&pmic_irq_pins_default>;
219 interrupt-parent = <&wkup_gpio0>;
220 interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
221 gpio-controller;
222 #gpio-cells = <2>;
223 ti,primary-pmic;
224 buck1-supply = <&vsys_3v3>;
225 buck2-supply = <&vsys_3v3>;
226 buck3-supply = <&vsys_3v3>;
227 buck4-supply = <&vsys_3v3>;
228 buck5-supply = <&vsys_3v3>;
229 ldo1-supply = <&vsys_3v3>;
230 ldo2-supply = <&vsys_3v3>;
231 ldo3-supply = <&vsys_3v3>;
232 ldo4-supply = <&vsys_3v3>;
233
234 regulators {
235 bucka1: buck1 {
236 regulator-name = "vda_mcu_1v8";
237 regulator-min-microvolt = <1800000>;
238 regulator-max-microvolt = <1800000>;
239 regulator-boot-on;
240 regulator-always-on;
241 bootph-all;
242 };
243
244 bucka2: buck2 {
245 regulator-name = "vdd_mcuio_1v8";
246 regulator-min-microvolt = <1800000>;
247 regulator-max-microvolt = <1800000>;
248 regulator-boot-on;
249 regulator-always-on;
250 };
251
252 bucka3: buck3 {
253 regulator-name = "vdd_mcu_0v85";
254 regulator-min-microvolt = <850000>;
255 regulator-max-microvolt = <850000>;
256 regulator-boot-on;
257 regulator-always-on;
258 };
259
260 bucka4: buck4 {
261 regulator-name = "vdd_ddr_1v1";
262 regulator-min-microvolt = <1100000>;
263 regulator-max-microvolt = <1100000>;
264 regulator-boot-on;
265 regulator-always-on;
266 };
267
268 bucka5: buck5 {
269 regulator-name = "vdd_phyio_1v8";
270 regulator-min-microvolt = <1800000>;
271 regulator-max-microvolt = <1800000>;
272 regulator-boot-on;
273 regulator-always-on;
274 };
275
276 ldoa1: ldo1 {
277 regulator-name = "vdd1_lpddr4_1v8";
278 regulator-min-microvolt = <1800000>;
279 regulator-max-microvolt = <1800000>;
280 regulator-boot-on;
281 regulator-always-on;
282 };
283
284 ldoa2: ldo2 {
285 regulator-name = "vda_dll_0v8";
286 regulator-min-microvolt = <800000>;
287 regulator-max-microvolt = <800000>;
288 regulator-boot-on;
289 regulator-always-on;
290 };
291
292 ldoa3: ldo3 {
293 regulator-name = "vdd_wk_0v8";
294 regulator-min-microvolt = <800000>;
295 regulator-max-microvolt = <800000>;
296 regulator-boot-on;
297 regulator-always-on;
298 };
299
300 ldoa4: ldo4 {
301 regulator-name = "vda_pll_1v8";
302 regulator-min-microvolt = <1800000>;
303 regulator-max-microvolt = <1800000>;
304 regulator-boot-on;
305 regulator-always-on;
306 };
307 };
308 };
309
310 lp876441: pmic@4c {
311 compatible = "ti,lp8764-q1";
312 reg = <0x4c>;
313 system-power-controller;
314 interrupt-parent = <&wkup_gpio0>;
315 interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
316 gpio-controller;
317 #gpio-cells = <2>;
318 buck1-supply = <&vsys_3v3>;
319 buck2-supply = <&vsys_3v3>;
320 buck3-supply = <&vsys_3v3>;
321 buck4-supply = <&vsys_3v3>;
322
323 regulators: regulators {
324 buckb1: buck1 {
325 regulator-name = "vdd_cpu_avs";
326 regulator-min-microvolt = <600000>;
327 regulator-max-microvolt = <900000>;
328 regulator-always-on;
329 regulator-boot-on;
330 bootph-pre-ram;
331 };
332
333 buckb2: buck2 {
334 regulator-name = "vdd_ram_0v85";
335 regulator-min-microvolt = <850000>;
336 regulator-max-microvolt = <850000>;
337 regulator-boot-on;
338 regulator-always-on;
339 };
340
341 buckb3: buck3 {
342 regulator-name = "vdd_core_0v85";
343 regulator-min-microvolt = <850000>;
344 regulator-max-microvolt = <850000>;
345 regulator-boot-on;
346 regulator-always-on;
347 };
348
349 buckb4: buck4 {
350 regulator-name = "vdd_io_1v8";
351 regulator-min-microvolt = <1800000>;
352 regulator-max-microvolt = <1800000>;
353 regulator-boot-on;
354 regulator-always-on;
355 };
356 };
357 };
358 };
359
360 &ospi0 {
361 status = "okay";
362 pinctrl-names = "default";
363 pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
364
365 flash@0 {
366 compatible = "jedec,spi-nor";
367 reg = <0x0>;
368 spi-tx-bus-width = <8>;
369 spi-rx-bus-width = <8>;
370 spi-max-frequency = <25000000>;
371 cdns,tshsl-ns = <60>;
372 cdns,tsd2d-ns = <60>;
373 cdns,tchsh-ns = <60>;
374 cdns,tslch-ns = <60>;
375 cdns,read-delay = <4>;
376
377 partitions {
378 compatible = "fixed-partitions";
379 #address-cells = <1>;
380 #size-cells = <1>;
381
382 partition@0 {
383 label = "ospi.tiboot3";
384 reg = <0x0 0x100000>;
385 };
386
387 partition@100000 {
388 label = "ospi.tispl";
389 reg = <0x100000 0x200000>;
390 };
391
392 partition@300000 {
393 label = "ospi.u-boot";
394 reg = <0x300000 0x400000>;
395 };
396
397 partition@700000 {
398 label = "ospi.env";
399 reg = <0x700000 0x40000>;
400 };
401
402 partition@740000 {
403 label = "ospi.env.backup";
404 reg = <0x740000 0x40000>;
405 };
406
407 partition@800000 {
408 label = "ospi.rootfs";
409 reg = <0x800000 0x37c0000>;
410 };
411
412 partition@3fc0000 {
413 label = "ospi.phypattern";
414 reg = <0x3fc0000 0x40000>;
415 bootph-all;
416 };
417 };
418 };
419 };
420
421 &main_mcan0 {
422 status = "okay";
423 pinctrl-0 = <&main_mcan0_pins_default>;
424 pinctrl-names = "default";
425 phys = <&transceiver0>;
426 };
427
428 #include "k3-j7200-ti-ipc-firmware.dtsi"