| 1 |
// SPDX-License-Identifier: GPL-2.0-only OR MIT |
| 2 |
/* |
| 3 |
* Copyright (C) 2025 PHYTEC Messtechnik GmbH |
| 4 |
* Author: Dominik Haller <[email protected]> |
| 5 |
* |
| 6 |
* https://www.phytec.eu/en/produkte/system-on-modules/phycore-am68x-tda4x/ |
| 7 |
*/ |
| 8 |
|
| 9 |
/dts-v1/; |
| 10 |
|
| 11 |
#include <dt-bindings/gpio/gpio.h> |
| 12 |
#include <dt-bindings/net/ti-dp83867.h> |
| 13 |
#include "k3-j721s2.dtsi" |
| 14 |
|
| 15 |
/ { |
| 16 |
compatible = "phytec,am68-phycore-som", "ti,j721s2"; |
| 17 |
model = "PHYTEC phyCORE-AM68x"; |
| 18 |
|
| 19 |
aliases { |
| 20 |
ethernet1 = &main_cpsw_port1; |
| 21 |
mmc0 = &main_sdhci0; |
| 22 |
rtc0 = &i2c_som_rtc; |
| 23 |
}; |
| 24 |
|
| 25 |
memory@80000000 { |
| 26 |
device_type = "memory"; |
| 27 |
/* 4GB RAM */ |
| 28 |
reg = <0x00000000 0x80000000 0x00000000 0x80000000>, |
| 29 |
<0x00000008 0x80000000 0x00000000 0x80000000>; |
| 30 |
bootph-all; |
| 31 |
}; |
| 32 |
|
| 33 |
reserved_memory: reserved-memory { |
| 34 |
#address-cells = <2>; |
| 35 |
#size-cells = <2>; |
| 36 |
ranges; |
| 37 |
|
| 38 |
/* global cma region */ |
| 39 |
linux,cma { |
| 40 |
compatible = "shared-dma-pool"; |
| 41 |
reusable; |
| 42 |
size = <0x00 0x20000000>; |
| 43 |
linux,cma-default; |
| 44 |
}; |
| 45 |
|
| 46 |
secure_ddr: optee@9e800000 { |
| 47 |
reg = <0x00 0x9e800000 0x00 0x01800000>; |
| 48 |
alignment = <0x1000>; |
| 49 |
no-map; |
| 50 |
}; |
| 51 |
|
| 52 |
mcu_r5fss0_core0_dma_memory_region: memory@a0000000 { |
| 53 |
compatible = "shared-dma-pool"; |
| 54 |
reg = <0x00 0xa0000000 0x00 0x100000>; |
| 55 |
no-map; |
| 56 |
}; |
| 57 |
|
| 58 |
mcu_r5fss0_core0_memory_region: memory@a0100000 { |
| 59 |
compatible = "shared-dma-pool"; |
| 60 |
reg = <0x00 0xa0100000 0x00 0xf00000>; |
| 61 |
no-map; |
| 62 |
}; |
| 63 |
}; |
| 64 |
|
| 65 |
vdd_sd_dv: regulator-sd { |
| 66 |
/* Output of TLV71033 */ |
| 67 |
compatible = "regulator-gpio"; |
| 68 |
regulator-name = "VDD_SD_DV"; |
| 69 |
pinctrl-names = "default"; |
| 70 |
pinctrl-0 = <&vdd_sd_dv_pins_default>; |
| 71 |
regulator-min-microvolt = <1800000>; |
| 72 |
regulator-max-microvolt = <3300000>; |
| 73 |
regulator-boot-on; |
| 74 |
gpios = <&main_gpio0 1 GPIO_ACTIVE_HIGH>; |
| 75 |
states = <3300000 0x0>, |
| 76 |
<1800000 0x1>; |
| 77 |
}; |
| 78 |
}; |
| 79 |
|
| 80 |
&main_pmx0 { |
| 81 |
main_cpsw_mdio_pins_default: main-cpsw-mdio-default-pins { |
| 82 |
pinctrl-single,pins = < |
| 83 |
J721S2_IOPAD(0x0c0, PIN_OUTPUT, 6) /* (T28) MCASP1_AXR0.MDIO0_MDC */ |
| 84 |
J721S2_IOPAD(0x0bc, PIN_INPUT, 6) /* (V28) MCASP1_AFSX.MDIO0_MDIO */ |
| 85 |
>; |
| 86 |
}; |
| 87 |
|
| 88 |
main_i2c0_pins_default: main-i2c0-default-pins { |
| 89 |
pinctrl-single,pins = < |
| 90 |
J721S2_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AH25) I2C0_SCL */ |
| 91 |
J721S2_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AE24) I2C0_SDA */ |
| 92 |
>; |
| 93 |
}; |
| 94 |
|
| 95 |
rgmii1_pins_default: rgmii1-default-pins { |
| 96 |
pinctrl-single,pins = < |
| 97 |
J721S2_IOPAD(0x0b8, PIN_INPUT, 6) /* (AA24) MCASP1_ACLKX.RGMII1_RD0 */ |
| 98 |
J721S2_IOPAD(0x0a0, PIN_INPUT, 6) /* (AB25) MCASP0_AXR12.RGMII1_RD1 */ |
| 99 |
J721S2_IOPAD(0x0a4, PIN_INPUT, 6) /* (T23) MCASP0_AXR13.RGMII1_RD2 */ |
| 100 |
J721S2_IOPAD(0x0a8, PIN_INPUT, 6) /* (U24) MCASP0_AXR14.RGMII1_RD3 */ |
| 101 |
J721S2_IOPAD(0x0b0, PIN_INPUT, 6) /* (AD26) MCASP1_AXR3.RGMII1_RXC */ |
| 102 |
J721S2_IOPAD(0x0ac, PIN_INPUT, 6) /* (AC25) MCASP0_AXR15.RGMII1_RX_CTL */ |
| 103 |
J721S2_IOPAD(0x08c, PIN_OUTPUT, 6) /* (T25) MCASP0_AXR7.RGMII1_TD0 */ |
| 104 |
J721S2_IOPAD(0x090, PIN_OUTPUT, 6) /* (W24) MCASP0_AXR8.RGMII1_TD1 */ |
| 105 |
J721S2_IOPAD(0x094, PIN_OUTPUT, 6) /* (AA25) MCASP0_AXR9.RGMII1_TD2 */ |
| 106 |
J721S2_IOPAD(0x098, PIN_OUTPUT, 6) /* (V25) MCASP0_AXR10.RGMII1_TD3 */ |
| 107 |
J721S2_IOPAD(0x0b4, PIN_OUTPUT, 6) /* (U25) MCASP1_AXR4.RGMII1_TXC */ |
| 108 |
J721S2_IOPAD(0x09c, PIN_OUTPUT, 6) /* (T24) MCASP0_AXR11.RGMII1_TX_CTL */ |
| 109 |
>; |
| 110 |
}; |
| 111 |
|
| 112 |
vdd_sd_dv_pins_default: vdd-sd-dv-default-pins { |
| 113 |
pinctrl-single,pins = < |
| 114 |
J721S2_IOPAD(0x004, PIN_OUTPUT, 7) /* (W25) MCAN12_TX.GPIO0_1 */ |
| 115 |
>; |
| 116 |
}; |
| 117 |
}; |
| 118 |
|
| 119 |
&wkup_pmx0 { |
| 120 |
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins { |
| 121 |
pinctrl-single,pins = < |
| 122 |
J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */ |
| 123 |
J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */ |
| 124 |
J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */ |
| 125 |
J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */ |
| 126 |
J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */ |
| 127 |
J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */ |
| 128 |
J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */ |
| 129 |
J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */ |
| 130 |
J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */ |
| 131 |
J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */ |
| 132 |
J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */ |
| 133 |
>; |
| 134 |
bootph-all; |
| 135 |
}; |
| 136 |
}; |
| 137 |
|
| 138 |
&wkup_pmx1 { |
| 139 |
pmic_irq_pins_default: pmic-irq-default-pins { |
| 140 |
pinctrl-single,pins = < |
| 141 |
J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 7) /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */ |
| 142 |
>; |
| 143 |
}; |
| 144 |
}; |
| 145 |
|
| 146 |
&wkup_pmx2 { |
| 147 |
wkup_i2c0_pins_default: wkup-i2c0-default-pins { |
| 148 |
pinctrl-single,pins = < |
| 149 |
J721S2_WKUP_IOPAD(0x098, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SCL */ |
| 150 |
J721S2_WKUP_IOPAD(0x09c, PIN_INPUT_PULLUP, 0) /* (H27) WKUP_I2C0_SDA */ |
| 151 |
>; |
| 152 |
bootph-all; |
| 153 |
}; |
| 154 |
}; |
| 155 |
|
| 156 |
&main_cpsw { |
| 157 |
pinctrl-names = "default"; |
| 158 |
pinctrl-0 = <&rgmii1_pins_default>; |
| 159 |
status = "okay"; |
| 160 |
}; |
| 161 |
|
| 162 |
&main_cpsw_mdio { |
| 163 |
pinctrl-names = "default"; |
| 164 |
pinctrl-0 = <&main_cpsw_mdio_pins_default>; |
| 165 |
status = "okay"; |
| 166 |
|
| 167 |
phy1: ethernet-phy@0 { |
| 168 |
reg = <0>; |
| 169 |
ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; |
| 170 |
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; |
| 171 |
ti,min-output-impedance; |
| 172 |
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; |
| 173 |
}; |
| 174 |
}; |
| 175 |
|
| 176 |
&main_cpsw_port1 { |
| 177 |
phy-handle = <&phy1>; |
| 178 |
phy-mode = "rgmii-id"; |
| 179 |
status = "okay"; |
| 180 |
}; |
| 181 |
|
| 182 |
&main_i2c0 { |
| 183 |
pinctrl-names = "default"; |
| 184 |
pinctrl-0 = <&main_i2c0_pins_default>; |
| 185 |
|
| 186 |
temperature-sensor@48 { |
| 187 |
compatible = "ti,tmp102"; |
| 188 |
reg = <0x48>; |
| 189 |
}; |
| 190 |
|
| 191 |
temperature-sensor@49 { |
| 192 |
compatible = "ti,tmp102"; |
| 193 |
reg = <0x49>; |
| 194 |
}; |
| 195 |
|
| 196 |
i2c_som_rtc: rtc@52 { |
| 197 |
compatible = "microcrystal,rv3028"; |
| 198 |
reg = <0x52>; |
| 199 |
}; |
| 200 |
}; |
| 201 |
|
| 202 |
&main_gpio0 { |
| 203 |
status = "okay"; |
| 204 |
}; |
| 205 |
|
| 206 |
/* eMMC */ |
| 207 |
&main_sdhci0 { |
| 208 |
non-removable; |
| 209 |
ti,driver-strength-ohm = <50>; |
| 210 |
bootph-all; |
| 211 |
status = "okay"; |
| 212 |
}; |
| 213 |
|
| 214 |
/* SD card */ |
| 215 |
&main_sdhci1 { |
| 216 |
vqmmc-supply = <&vdd_sd_dv>; |
| 217 |
bootph-all; |
| 218 |
}; |
| 219 |
|
| 220 |
&ospi0 { |
| 221 |
pinctrl-names = "default"; |
| 222 |
pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; |
| 223 |
status = "okay"; |
| 224 |
|
| 225 |
serial_flash: flash@0 { |
| 226 |
compatible = "jedec,spi-nor"; |
| 227 |
reg = <0x0>; |
| 228 |
spi-tx-bus-width = <8>; |
| 229 |
spi-rx-bus-width = <8>; |
| 230 |
spi-max-frequency = <25000000>; |
| 231 |
cdns,tshsl-ns = <60>; |
| 232 |
cdns,tsd2d-ns = <60>; |
| 233 |
cdns,tchsh-ns = <60>; |
| 234 |
cdns,tslch-ns = <60>; |
| 235 |
cdns,read-delay = <2>; |
| 236 |
bootph-all; |
| 237 |
}; |
| 238 |
}; |
| 239 |
|
| 240 |
&wkup_gpio0 { |
| 241 |
status = "okay"; |
| 242 |
}; |
| 243 |
|
| 244 |
&wkup_i2c0 { |
| 245 |
pinctrl-names = "default"; |
| 246 |
pinctrl-0 = <&wkup_i2c0_pins_default>; |
| 247 |
clock-frequency = <400000>; |
| 248 |
status = "okay"; |
| 249 |
|
| 250 |
vdd_cpu_avs: regulator@40 { |
| 251 |
compatible = "ti,tps62873"; |
| 252 |
reg = <0x40>; |
| 253 |
regulator-name = "VDD_CPU_AVS"; |
| 254 |
regulator-min-microvolt = <600000>; |
| 255 |
regulator-max-microvolt = <900000>; |
| 256 |
regulator-boot-on; |
| 257 |
regulator-always-on; |
| 258 |
bootph-pre-ram; |
| 259 |
}; |
| 260 |
|
| 261 |
pmic: pmic@48 { |
| 262 |
compatible = "ti,tps6594-q1"; |
| 263 |
reg = <0x48>; |
| 264 |
system-power-controller; |
| 265 |
pinctrl-names = "default"; |
| 266 |
pinctrl-0 = <&pmic_irq_pins_default>; |
| 267 |
interrupt-parent = <&wkup_gpio0>; |
| 268 |
interrupts = <39 IRQ_TYPE_EDGE_FALLING>; |
| 269 |
gpio-controller; |
| 270 |
#gpio-cells = <2>; |
| 271 |
buck12-supply = <&vcc_3v3>; |
| 272 |
buck3-supply = <&vcc_3v3>; |
| 273 |
buck4-supply = <&vcc_3v3>; |
| 274 |
buck5-supply = <&vcc_3v3>; |
| 275 |
ldo1-supply = <&vcc_3v3>; |
| 276 |
ldo2-supply = <&vcc_3v3>; |
| 277 |
ldo3-supply = <&vcc_3v3>; |
| 278 |
ldo4-supply = <&vcc_3v3>; |
| 279 |
ti,primary-pmic; |
| 280 |
|
| 281 |
regulators { |
| 282 |
bucka12: buck12 { |
| 283 |
regulator-name = "VDD_DDR_1V1"; |
| 284 |
regulator-min-microvolt = <1100000>; |
| 285 |
regulator-max-microvolt = <1100000>; |
| 286 |
regulator-boot-on; |
| 287 |
regulator-always-on; |
| 288 |
bootph-all; |
| 289 |
}; |
| 290 |
|
| 291 |
bucka3: buck3 { |
| 292 |
regulator-name = "VDD_RAM_0V85"; |
| 293 |
regulator-min-microvolt = <850000>; |
| 294 |
regulator-max-microvolt = <850000>; |
| 295 |
regulator-boot-on; |
| 296 |
regulator-always-on; |
| 297 |
bootph-all; |
| 298 |
}; |
| 299 |
|
| 300 |
bucka4: buck4 { |
| 301 |
regulator-name = "VDD_IO_1V8"; |
| 302 |
regulator-min-microvolt = <1800000>; |
| 303 |
regulator-max-microvolt = <1800000>; |
| 304 |
regulator-boot-on; |
| 305 |
regulator-always-on; |
| 306 |
bootph-all; |
| 307 |
}; |
| 308 |
|
| 309 |
bucka5: buck5 { |
| 310 |
regulator-name = "VDD_MCU_0V85"; |
| 311 |
regulator-min-microvolt = <850000>; |
| 312 |
regulator-max-microvolt = <850000>; |
| 313 |
regulator-boot-on; |
| 314 |
regulator-always-on; |
| 315 |
bootph-all; |
| 316 |
}; |
| 317 |
|
| 318 |
ldoa1: ldo1 { |
| 319 |
regulator-name = "VDD_MCUIO_1V8"; |
| 320 |
regulator-min-microvolt = <1800000>; |
| 321 |
regulator-max-microvolt = <1800000>; |
| 322 |
regulator-boot-on; |
| 323 |
regulator-always-on; |
| 324 |
bootph-all; |
| 325 |
}; |
| 326 |
|
| 327 |
ldoa2: ldo2 { |
| 328 |
regulator-name = "VDD_MCUIO_3V3"; |
| 329 |
regulator-min-microvolt = <3300000>; |
| 330 |
regulator-max-microvolt = <3300000>; |
| 331 |
regulator-boot-on; |
| 332 |
regulator-always-on; |
| 333 |
bootph-all; |
| 334 |
}; |
| 335 |
|
| 336 |
ldoa3: ldo3 { |
| 337 |
regulator-name = "VDDA_DLL_0V8"; |
| 338 |
regulator-min-microvolt = <800000>; |
| 339 |
regulator-max-microvolt = <800000>; |
| 340 |
regulator-boot-on; |
| 341 |
regulator-always-on; |
| 342 |
bootph-all; |
| 343 |
}; |
| 344 |
|
| 345 |
ldoa4: ldo4 { |
| 346 |
regulator-name = "VDDA_MCU_1V8"; |
| 347 |
regulator-min-microvolt = <1800000>; |
| 348 |
regulator-max-microvolt = <1800000>; |
| 349 |
regulator-boot-on; |
| 350 |
regulator-always-on; |
| 351 |
bootph-all; |
| 352 |
}; |
| 353 |
}; |
| 354 |
}; |
| 355 |
|
| 356 |
eeprom@50 { |
| 357 |
compatible = "atmel,24c32"; |
| 358 |
reg = <0x50>; |
| 359 |
pagesize = <32>; |
| 360 |
bootph-all; |
| 361 |
}; |
| 362 |
|
| 363 |
som_eeprom_opt: eeprom@51 { |
| 364 |
compatible = "atmel,24c32"; |
| 365 |
reg = <0x51>; |
| 366 |
pagesize = <32>; |
| 367 |
}; |
| 368 |
}; |
| 369 |
|
| 370 |
#include "k3-j721s2-ti-ipc-firmware.dtsi" |