Debian Codegraph @

scripts/dtc/include-prefixes/arm64/ti/k3-am625-beagleplay.dts

raw
1 // SPDX-License-Identifier: GPL-2.0-only OR MIT
2 /*
3 * https://beagleplay.org/
4 *
5 * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
6 * Copyright (C) 2022-2024 Robert Nelson, BeagleBoard.org Foundation
7 */
8
9 /dts-v1/;
10
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/gpio/gpio.h>
13 #include <dt-bindings/input/input.h>
14 #include "k3-am625.dtsi"
15
16 / {
17 compatible = "beagle,am625-beagleplay", "ti,am625";
18 model = "BeagleBoard.org BeaglePlay";
19
20 aliases {
21 ethernet0 = &cpsw_port1;
22 ethernet1 = &cpsw_port2;
23 gpio0 = &main_gpio0;
24 gpio1 = &main_gpio1;
25 gpio2 = &mcu_gpio0;
26 i2c0 = &main_i2c0;
27 i2c1 = &main_i2c1;
28 i2c2 = &main_i2c2;
29 i2c3 = &main_i2c3;
30 i2c4 = &wkup_i2c0;
31 i2c5 = &mcu_i2c0;
32 mmc0 = &sdhci0;
33 mmc1 = &sdhci1;
34 mmc2 = &sdhci2;
35 rtc0 = &rtc;
36 serial0 = &main_uart5;
37 serial1 = &main_uart6;
38 serial2 = &main_uart0;
39 usb0 = &usb0;
40 usb1 = &usb1;
41 };
42
43 chosen {
44 stdout-path = "serial2:115200n8";
45 };
46
47 memory@80000000 {
48 bootph-pre-ram;
49 device_type = "memory";
50 /* 2G RAM */
51 reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
52 };
53
54 reserved-memory {
55 #address-cells = <2>;
56 #size-cells = <2>;
57 ranges;
58
59 ramoops: ramoops@9ca00000 {
60 compatible = "ramoops";
61 reg = <0x00 0x9ca00000 0x00 0x00100000>;
62 record-size = <0x8000>;
63 console-size = <0x8000>;
64 ftrace-size = <0x00>;
65 pmsg-size = <0x8000>;
66 };
67
68 /* global cma region */
69 linux,cma {
70 compatible = "shared-dma-pool";
71 reusable;
72 size = <0x00 0x8000000>;
73 linux,cma-default;
74 };
75
76 secure_tfa_ddr: tfa@9e780000 {
77 reg = <0x00 0x9e780000 0x00 0x80000>;
78 no-map;
79 };
80
81 secure_ddr: optee@9e800000 {
82 reg = <0x00 0x9e800000 0x00 0x01800000>;
83 no-map;
84 };
85
86 wkup_r5fss0_core0_dma_memory_region: memory@9db00000 {
87 compatible = "shared-dma-pool";
88 reg = <0x00 0x9db00000 0x00 0xc00000>;
89 no-map;
90 };
91 };
92
93 sdio_pwrseq: sdio-pwrseq {
94 compatible = "mmc-pwrseq-simple";
95 pinctrl-names = "default";
96 pinctrl-0 = <&wifi_en_pins_default>;
97 /* Internal power on time(Figure 8-3) * 2 */
98 post-power-on-delay-ms = <10>;
99 /* Re-enable time(Figure 8-2) + 20uS */
100 power-off-delay-us = <80>;
101 reset-gpios = <&main_gpio0 38 GPIO_ACTIVE_LOW>;
102 };
103
104 vsys_5v0: regulator-1 {
105 bootph-all;
106 compatible = "regulator-fixed";
107 regulator-name = "vsys_5v0";
108 regulator-min-microvolt = <5000000>;
109 regulator-max-microvolt = <5000000>;
110 regulator-always-on;
111 regulator-boot-on;
112 };
113
114 vdd_3v3: regulator-2 {
115 /* output of TLV62595DMQR-U12 */
116 bootph-all;
117 compatible = "regulator-fixed";
118 regulator-name = "vdd_3v3";
119 regulator-min-microvolt = <3300000>;
120 regulator-max-microvolt = <3300000>;
121 vin-supply = <&vsys_5v0>;
122 regulator-always-on;
123 regulator-boot-on;
124 };
125
126 vdd_3v3_sd: regulator-4 {
127 /* output of TPS22918DBVR-U21 */
128 bootph-all;
129 pinctrl-names = "default";
130 pinctrl-0 = <&vdd_3v3_sd_pins_default>;
131
132 compatible = "regulator-fixed";
133 regulator-name = "vdd_3v3_sd";
134 regulator-min-microvolt = <3300000>;
135 regulator-max-microvolt = <3300000>;
136 enable-active-high;
137 regulator-always-on;
138 vin-supply = <&vdd_3v3>;
139 gpio = <&main_gpio1 19 GPIO_ACTIVE_HIGH>;
140 };
141
142 vdd_sd_dv: regulator-5 {
143 bootph-all;
144 compatible = "regulator-gpio";
145 regulator-name = "sd_hs200_switch";
146 pinctrl-names = "default";
147 pinctrl-0 = <&vdd_sd_dv_pins_default>;
148 regulator-min-microvolt = <1800000>;
149 regulator-max-microvolt = <3300000>;
150 regulator-boot-on;
151 vin-supply = <&ldo1_reg>;
152 gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
153 states = <1800000 0x0>,
154 <3300000 0x1>;
155 };
156
157 leds {
158 bootph-all;
159 compatible = "gpio-leds";
160
161 led-0 {
162 bootph-all;
163 gpios = <&main_gpio0 3 GPIO_ACTIVE_HIGH>;
164 linux,default-trigger = "heartbeat";
165 function = LED_FUNCTION_HEARTBEAT;
166 default-state = "off";
167 };
168
169 led-1 {
170 bootph-all;
171 gpios = <&main_gpio0 4 GPIO_ACTIVE_HIGH>;
172 linux,default-trigger = "disk-activity";
173 function = LED_FUNCTION_DISK_ACTIVITY;
174 default-state = "keep";
175 };
176
177 led-2 {
178 bootph-all;
179 gpios = <&main_gpio0 5 GPIO_ACTIVE_HIGH>;
180 function = LED_FUNCTION_CPU;
181 };
182
183 led-3 {
184 bootph-all;
185 gpios = <&main_gpio0 6 GPIO_ACTIVE_HIGH>;
186 function = LED_FUNCTION_LAN;
187 };
188
189 led-4 {
190 bootph-all;
191 gpios = <&main_gpio0 9 GPIO_ACTIVE_HIGH>;
192 function = LED_FUNCTION_WLAN;
193 };
194 };
195
196 gpio_keys: gpio-keys {
197 compatible = "gpio-keys";
198 autorepeat;
199 pinctrl-names = "default";
200 pinctrl-0 = <&usr_button_pins_default>;
201
202 usr: button-usr {
203 label = "User Key";
204 linux,code = <BTN_0>;
205 gpios = <&main_gpio0 18 GPIO_ACTIVE_LOW>;
206 };
207
208 };
209
210 hdmi0: connector-hdmi {
211 compatible = "hdmi-connector";
212 label = "hdmi";
213 type = "a";
214 port {
215 hdmi_connector_in: endpoint {
216 remote-endpoint = <&it66121_out>;
217 };
218 };
219 };
220
221 sound {
222 compatible = "simple-audio-card";
223 simple-audio-card,name = "it66121 HDMI";
224 simple-audio-card,format = "i2s";
225 simple-audio-card,bitclock-master = <&hdmi_dailink_master>;
226 simple-audio-card,frame-master = <&hdmi_dailink_master>;
227
228 hdmi_dailink_master: simple-audio-card,cpu {
229 sound-dai = <&mcasp1>;
230 system-clock-direction-out;
231 };
232
233 simple-audio-card,codec {
234 sound-dai = <&it66121>;
235 };
236 };
237
238 };
239
240 &main_pmx0 {
241 gpio0_pins_default: gpio0-default-pins {
242 bootph-all;
243 pinctrl-single,pins = <
244 AM62X_IOPAD(0x0004, PIN_INPUT, 7) /* (G25) OSPI0_LBCLKO.GPIO0_1 */
245 AM62X_IOPAD(0x0008, PIN_INPUT, 7) /* (J24) OSPI0_DQS.GPIO0_2 */
246 AM62X_IOPAD(0x000c, PIN_INPUT, 7) /* (E25) OSPI0_D0.GPIO0_3 */
247 AM62X_IOPAD(0x0010, PIN_INPUT, 7) /* (G24) OSPI0_D1.GPIO0_4 */
248 AM62X_IOPAD(0x0014, PIN_INPUT, 7) /* (F25) OSPI0_D2.GPIO0_5 */
249 AM62X_IOPAD(0x0018, PIN_INPUT, 7) /* (F24) OSPI0_D3.GPIO0_6 */
250 AM62X_IOPAD(0x0024, PIN_INPUT, 7) /* (H25) OSPI0_D6.GPIO0_9 */
251 AM62X_IOPAD(0x0028, PIN_INPUT, 7) /* (J22) OSPI0_D7.GPIO0_10 */
252 AM62X_IOPAD(0x002c, PIN_INPUT, 7) /* (F23) OSPI0_CSn0.GPIO0_11 */
253 AM62X_IOPAD(0x0030, PIN_INPUT, 7) /* (G21) OSPI0_CSn1.GPIO0_12 */
254 AM62X_IOPAD(0x0034, PIN_INPUT, 7) /* (H21) OSPI0_CSn2.GPIO0_13 */
255 AM62X_IOPAD(0x0038, PIN_INPUT, 7) /* (E24) OSPI0_CSn3.GPIO0_14 */
256 AM62X_IOPAD(0x00a4, PIN_INPUT, 7) /* (M22) GPMC0_DIR.GPIO0_40 */
257 AM62X_IOPAD(0x00ac, PIN_INPUT, 7) /* (L21) GPMC0_CSn1.GPIO0_42 */
258 >;
259 };
260
261 vdd_sd_dv_pins_default: vdd-sd-default-pins {
262 bootph-all;
263 pinctrl-single,pins = <
264 AM62X_IOPAD(0x0244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
265 >;
266 };
267
268 usr_button_pins_default: usr-button-default-pins {
269 pinctrl-single,pins = <
270 AM62X_IOPAD(0x0048, PIN_INPUT, 7) /* (N25) GPMC0_AD3.GPIO0_18 */
271 >;
272 };
273
274 grove_pins_default: grove-default-pins {
275 pinctrl-single,pins = <
276 AM62X_IOPAD(0x01e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
277 AM62X_IOPAD(0x01ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
278 >;
279 };
280
281 local_i2c_pins_default: local-i2c-default-pins {
282 bootph-all;
283 pinctrl-single,pins = <
284 AM62X_IOPAD(0x01e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
285 AM62X_IOPAD(0x01e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
286 >;
287 };
288
289 i2c2_1v8_pins_default: i2c2-default-pins {
290 pinctrl-single,pins = <
291 AM62X_IOPAD(0x00b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */
292 AM62X_IOPAD(0x00b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */
293 >;
294 };
295
296 mdio0_pins_default: mdio0-default-pins {
297 pinctrl-single,pins = <
298 AM62X_IOPAD(0x0160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
299 AM62X_IOPAD(0x015c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
300 AM62X_IOPAD(0x003c, PIN_INPUT, 7) /* (M25) GPMC0_AD0.GPIO0_15 */
301 AM62X_IOPAD(0x018c, PIN_INPUT, 7) /* (AC21) RGMII2_RD2.GPIO1_5 */
302 >;
303 };
304
305 rgmii1_pins_default: rgmii1-default-pins {
306 pinctrl-single,pins = <
307 AM62X_IOPAD(0x014c, PIN_INPUT, 0) /* (AB17) RGMII1_RD0 */
308 AM62X_IOPAD(0x0150, PIN_INPUT, 0) /* (AC17) RGMII1_RD1 */
309 AM62X_IOPAD(0x0154, PIN_INPUT, 0) /* (AB16) RGMII1_RD2 */
310 AM62X_IOPAD(0x0158, PIN_INPUT, 0) /* (AA15) RGMII1_RD3 */
311 AM62X_IOPAD(0x0148, PIN_INPUT, 0) /* (AD17) RGMII1_RXC */
312 AM62X_IOPAD(0x0144, PIN_INPUT, 0) /* (AE17) RGMII1_RX_CTL */
313 AM62X_IOPAD(0x0134, PIN_OUTPUT, 0) /* (AE20) RGMII1_TD0 */
314 AM62X_IOPAD(0x0138, PIN_OUTPUT, 0) /* (AD20) RGMII1_TD1 */
315 AM62X_IOPAD(0x013c, PIN_OUTPUT, 0) /* (AE18) RGMII1_TD2 */
316 AM62X_IOPAD(0x0140, PIN_OUTPUT, 0) /* (AD18) RGMII1_TD3 */
317 AM62X_IOPAD(0x0130, PIN_OUTPUT, 0) /* (AE19) RGMII1_TXC */
318 AM62X_IOPAD(0x012c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */
319 >;
320 };
321
322 emmc_pins_default: emmc-default-pins {
323 bootph-all;
324 pinctrl-single,pins = <
325 AM62X_IOPAD(0x0220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
326 AM62X_IOPAD(0x0218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
327 AM62X_IOPAD(0x0214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
328 AM62X_IOPAD(0x0210, PIN_INPUT, 0) /* (AA1) MMC0_DAT1 */
329 AM62X_IOPAD(0x020c, PIN_INPUT, 0) /* (AA3) MMC0_DAT2 */
330 AM62X_IOPAD(0x0208, PIN_INPUT, 0) /* (Y4) MMC0_DAT3 */
331 AM62X_IOPAD(0x0204, PIN_INPUT, 0) /* (AB2) MMC0_DAT4 */
332 AM62X_IOPAD(0x0200, PIN_INPUT, 0) /* (AC1) MMC0_DAT5 */
333 AM62X_IOPAD(0x01fc, PIN_INPUT, 0) /* (AD2) MMC0_DAT6 */
334 AM62X_IOPAD(0x01f8, PIN_INPUT, 0) /* (AC2) MMC0_DAT7 */
335 >;
336 };
337
338 vdd_3v3_sd_pins_default: vdd-3v3-sd-default-pins {
339 bootph-all;
340 pinctrl-single,pins = <
341 AM62X_IOPAD(0x01c4, PIN_INPUT, 7) /* (B14) SPI0_D1_GPIO1_19 */
342 >;
343 };
344
345 sd_pins_default: sd-default-pins {
346 bootph-all;
347 pinctrl-single,pins = <
348 AM62X_IOPAD(0x023c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
349 AM62X_IOPAD(0x0234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
350 AM62X_IOPAD(0x0230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */
351 AM62X_IOPAD(0x022c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */
352 AM62X_IOPAD(0x0228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
353 AM62X_IOPAD(0x0224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
354 AM62X_IOPAD(0x0240, PIN_INPUT, 7) /* (D17) MMC1_SDCD.GPIO1_48 */
355 >;
356 };
357
358 wifi_pins_default: wifi-default-pins {
359 pinctrl-single,pins = <
360 AM62X_IOPAD(0x0120, PIN_INPUT, 0) /* (C24) MMC2_CMD */
361 AM62X_IOPAD(0x0118, PIN_INPUT, 0) /* (D25) MMC2_CLK */
362 AM62X_IOPAD(0x0114, PIN_INPUT, 0) /* (B24) MMC2_DAT0 */
363 AM62X_IOPAD(0x0110, PIN_INPUT, 0) /* (C25) MMC2_DAT1 */
364 AM62X_IOPAD(0x010c, PIN_INPUT, 0) /* (E23) MMC2_DAT2 */
365 AM62X_IOPAD(0x0108, PIN_INPUT, 0) /* (D24) MMC2_DAT3 */
366 AM62X_IOPAD(0x0124, PIN_INPUT, 0) /* (A23) MMC2_SDCD */
367 AM62X_IOPAD(0x11c, PIN_INPUT, 0) /* (#N/A) MMC2_CLKB */
368 >;
369 };
370
371 wifi_en_pins_default: wifi-en-default-pins {
372 pinctrl-single,pins = <
373 AM62X_IOPAD(0x009c, PIN_OUTPUT, 7) /* (V25) GPMC0_WAIT1.GPIO0_38 */
374 >;
375 };
376
377 wifi_wlirq_pins_default: wifi-wlirq-default-pins {
378 pinctrl-single,pins = <
379 AM62X_IOPAD(0x00a8, PIN_INPUT, 7) /* (M21) GPMC0_CSn0.GPIO0_41 */
380 >;
381 };
382
383 spe_pins_default: spe-default-pins {
384 pinctrl-single,pins = <
385 AM62X_IOPAD(0x0168, PIN_INPUT, 1) /* (AE21) RGMII2_TXC.RMII2_CRS_DV */
386 AM62X_IOPAD(0x0180, PIN_INPUT, 1) /* (AD23) RGMII2_RXC.RMII2_REF_CLK */
387 AM62X_IOPAD(0x0184, PIN_INPUT, 1) /* (AE23) RGMII2_RD0.RMII2_RXD0 */
388 AM62X_IOPAD(0x0188, PIN_INPUT, 1) /* (AB20) RGMII2_RD1.RMII2_RXD1 */
389 AM62X_IOPAD(0x017c, PIN_INPUT, 1) /* (AD22) RGMII2_RX_CTL.RMII2_RX_ER */
390 AM62X_IOPAD(0x016c, PIN_INPUT, 1) /* (Y18) RGMII2_TD0.RMII2_TXD0 */
391 AM62X_IOPAD(0x0170, PIN_INPUT, 1) /* (AA18) RGMII2_TD1.RMII2_TXD1 */
392 AM62X_IOPAD(0x0164, PIN_INPUT, 1) /* (AA19) RGMII2_TX_CTL.RMII2_TX_EN */
393 AM62X_IOPAD(0x0190, PIN_INPUT, 7) /* (AE22) RGMII2_RD3.GPIO1_6 */
394 AM62X_IOPAD(0x01f0, PIN_OUTPUT, 5) /* (A18) EXT_REFCLK1.CLKOUT0 */
395 >;
396 };
397
398 mikrobus_i2c_pins_default: mikrobus-i2c-default-pins {
399 pinctrl-single,pins = <
400 AM62X_IOPAD(0x01d0, PIN_INPUT_PULLUP, 2) /* (A15) UART0_CTSn.I2C3_SCL */
401 AM62X_IOPAD(0x01d4, PIN_INPUT_PULLUP, 2) /* (B15) UART0_RTSn.I2C3_SDA */
402 >;
403 };
404
405 mikrobus_uart_pins_default: mikrobus-uart-default-pins {
406 pinctrl-single,pins = <
407 AM62X_IOPAD(0x01d8, PIN_INPUT, 1) /* (C15) MCAN0_TX.UART5_RXD */
408 AM62X_IOPAD(0x01dc, PIN_OUTPUT, 1) /* (E15) MCAN0_RX.UART5_TXD */
409 >;
410 };
411
412 mikrobus_spi_pins_default: mikrobus-spi-default-pins {
413 pinctrl-single,pins = <
414 AM62X_IOPAD(0x01b0, PIN_INPUT, 1) /* (A20) MCASP0_ACLKR.SPI2_CLK */
415 AM62X_IOPAD(0x01ac, PIN_INPUT, 1) /* (E19) MCASP0_AFSR.SPI2_CS0 */
416 AM62X_IOPAD(0x0194, PIN_INPUT, 1) /* (B19) MCASP0_AXR3.SPI2_D0 */
417 AM62X_IOPAD(0x0198, PIN_INPUT, 1) /* (A19) MCASP0_AXR2.SPI2_D1 */
418 >;
419 };
420
421 mikrobus_gpio_pins_default: mikrobus-gpio-default-pins {
422 bootph-all;
423 pinctrl-single,pins = <
424 AM62X_IOPAD(0x019c, PIN_INPUT, 7) /* (B18) MCASP0_AXR1.GPIO1_9 */
425 AM62X_IOPAD(0x01a0, PIN_INPUT, 7) /* (E18) MCASP0_AXR0.GPIO1_10 */
426 AM62X_IOPAD(0x01a8, PIN_INPUT, 7) /* (D20) MCASP0_AFSX.GPIO1_12 */
427 >;
428 };
429
430 mikrobus_pwm_pins_default: mikrobus-pwm-default-pins {
431 pinctrl-single,pins = <
432 AM62X_IOPAD(0x01a4, PIN_INPUT, 2) /* (B20) MCASP0_ACLKX.ECAP2_IN_APWM_OUT */
433 >;
434 };
435
436 main_uart0_pins_default: main-uart0-default-pins {
437 bootph-all;
438 pinctrl-single,pins = <
439 AM62X_IOPAD(0x01c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
440 AM62X_IOPAD(0x01cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
441 >;
442 };
443
444 wifi_debug_uart_pins_default: wifi-debug-uart-default-pins {
445 pinctrl-single,pins = <
446 AM62X_IOPAD(0x001c, PIN_INPUT, 3) /* (J23) OSPI0_D4.UART6_RXD */
447 AM62X_IOPAD(0x0020, PIN_OUTPUT, 3) /* (J25) OSPI0_D5.UART6_TXD */
448 >;
449 };
450
451 usb1_pins_default: usb1-default-pins {
452 pinctrl-single,pins = <
453 AM62X_IOPAD(0x0258, PIN_INPUT, 0) /* (F18) USB1_DRVVBUS */
454 >;
455 };
456
457 pmic_irq_pins_default: pmic-irq-default-pins {
458 pinctrl-single,pins = <
459 AM62X_IOPAD(0x01f4, PIN_INPUT_PULLUP, 0) /* (D16) EXTINTn */
460 >;
461 };
462
463 hdmi_gpio_pins_default: hdmi-gpio-default-pins {
464 pinctrl-single,pins = <
465 AM62X_IOPAD(0x0094, PIN_INPUT_PULLUP | PIN_DEBOUNCE_CONF6, 7) /* (N20) GPMC0_BE1n.GPIO0_36 */
466 AM62X_IOPAD(0x0054, PIN_OUTPUT_PULLUP, 7) /* (P21) GPMC0_AD6.GPIO0_21 */
467 >;
468 };
469
470 mcasp_hdmi_pins_default: mcasp-hdmi-default-pins {
471 pinctrl-single,pins = <
472 AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0n_CLE.MCASP1_ACLKX */
473 AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
474 AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEn.MCASP1_AXR0 */
475 AM62X_IOPAD(0x0088, PIN_INPUT, 2) /* (L24) GPMC0_OEn_REn.MCASP1_AXR1 */
476 AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVn_ALE.MCASP1_AXR2 */
477 AM62X_IOPAD(0x007c, PIN_INPUT, 2) /* (P25) GPMC0_CLK.MCASP1_AXR3 */
478 >;
479 };
480
481 dss0_pins_default: dss0-default-pins {
482 pinctrl-single,pins = <
483 AM62X_IOPAD(0x0100, PIN_OUTPUT, 0) /* (AC25) VOUT0_VSYNC */
484 AM62X_IOPAD(0x00f8, PIN_OUTPUT, 0) /* (AB24) VOUT0_HSYNC */
485 AM62X_IOPAD(0x0104, PIN_OUTPUT, 0) /* (AC24) VOUT0_PCLK */
486 AM62X_IOPAD(0x00fc, PIN_OUTPUT, 0) /* (Y20) VOUT0_DE */
487 AM62X_IOPAD(0x00b8, PIN_OUTPUT, 0) /* (U22) VOUT0_DATA0 */
488 AM62X_IOPAD(0x00bc, PIN_OUTPUT, 0) /* (V24) VOUT0_DATA1 */
489 AM62X_IOPAD(0x00c0, PIN_OUTPUT, 0) /* (W25) VOUT0_DATA2 */
490 AM62X_IOPAD(0x00c4, PIN_OUTPUT, 0) /* (W24) VOUT0_DATA3 */
491 AM62X_IOPAD(0x00c8, PIN_OUTPUT, 0) /* (Y25) VOUT0_DATA4 */
492 AM62X_IOPAD(0x00cc, PIN_OUTPUT, 0) /* (Y24) VOUT0_DATA5 */
493 AM62X_IOPAD(0x00d0, PIN_OUTPUT, 0) /* (Y23) VOUT0_DATA6 */
494 AM62X_IOPAD(0x00d4, PIN_OUTPUT, 0) /* (AA25) VOUT0_DATA7 */
495 AM62X_IOPAD(0x00d8, PIN_OUTPUT, 0) /* (V21) VOUT0_DATA8 */
496 AM62X_IOPAD(0x00dc, PIN_OUTPUT, 0) /* (W21) VOUT0_DATA9 */
497 AM62X_IOPAD(0x00e0, PIN_OUTPUT, 0) /* (V20) VOUT0_DATA10 */
498 AM62X_IOPAD(0x00e4, PIN_OUTPUT, 0) /* (AA23) VOUT0_DATA11 */
499 AM62X_IOPAD(0x00e8, PIN_OUTPUT, 0) /* (AB25) VOUT0_DATA12 */
500 AM62X_IOPAD(0x00ec, PIN_OUTPUT, 0) /* (AA24) VOUT0_DATA13 */
501 AM62X_IOPAD(0x00f0, PIN_OUTPUT, 0) /* (Y22) VOUT0_DATA14 */
502 AM62X_IOPAD(0x00f4, PIN_OUTPUT, 0) /* (AA21) VOUT0_DATA15 */
503 AM62X_IOPAD(0x005c, PIN_OUTPUT, 1) /* (R24) GPMC0_AD8.VOUT0_DATA16 */
504 AM62X_IOPAD(0x0060, PIN_OUTPUT, 1) /* (R25) GPMC0_AD9.VOUT0_DATA17 */
505 AM62X_IOPAD(0x0064, PIN_OUTPUT, 1) /* (T25) GPMC0_AD10.VOUT0_DATA18 */
506 AM62X_IOPAD(0x0068, PIN_OUTPUT, 1) /* (R21) GPMC0_AD11.VOUT0_DATA19 */
507 AM62X_IOPAD(0x006c, PIN_OUTPUT, 1) /* (T22) GPMC0_AD12.VOUT0_DATA20 */
508 AM62X_IOPAD(0x0070, PIN_OUTPUT, 1) /* (T24) GPMC0_AD13.VOUT0_DATA21 */
509 AM62X_IOPAD(0x0074, PIN_OUTPUT, 1) /* (U25) GPMC0_AD14.VOUT0_DATA22 */
510 AM62X_IOPAD(0x0078, PIN_OUTPUT, 1) /* (U24) GPMC0_AD15.VOUT0_DATA23 */
511 >;
512 };
513 };
514
515 &mcu_pmx0 {
516 i2c_qwiic_pins_default: i2c-qwiic-default-pins {
517 pinctrl-single,pins = <
518 AM62X_MCU_IOPAD(0x0044, PIN_INPUT, 0) /* (A8) MCU_I2C0_SCL */
519 AM62X_MCU_IOPAD(0x0048, PIN_INPUT, 0) /* (D10) MCU_I2C0_SDA */
520 >;
521 };
522
523 gbe_pmx_obsclk: gbe-pmx-obsclk-default-pins {
524 pinctrl-single,pins = <
525 AM62X_MCU_IOPAD(0x0004, PIN_OUTPUT, 1) /* (B8) MCU_SPI0_CS1.MCU_OBSCLK0 */
526 >;
527 };
528
529 i2c_csi_pins_default: i2c-csi-default-pins {
530 pinctrl-single,pins = <
531 AM62X_MCU_IOPAD(0x004c, PIN_INPUT_PULLUP, 0) /* (B9) WKUP_I2C0_SCL */
532 AM62X_MCU_IOPAD(0x0050, PIN_INPUT_PULLUP, 0) /* (A9) WKUP_I2C0_SDA */
533 >;
534 };
535
536 wifi_32k_clk: mcu-clk-out-default-pins {
537 pinctrl-single,pins = <
538 AM62X_MCU_IOPAD(0x0084, PIN_OUTPUT, 0) /* (A12) WKUP_CLKOUT0 */
539 >;
540 };
541 };
542
543 &a53_opp_table {
544 /* Requires VDD_CORE to be at 0.85V */
545 opp-1400000000 {
546 opp-hz = /bits/ 64 <1400000000>;
547 opp-supported-hw = <0x01 0x0004>;
548 };
549 };
550
551 &wkup_i2c0 {
552 pinctrl-names = "default";
553 pinctrl-0 = <&i2c_csi_pins_default>;
554 clock-frequency = <400000>;
555 /* Enable with overlay for camera sensor */
556 };
557
558 &mcu_i2c0 {
559 pinctrl-names = "default";
560 pinctrl-0 = <&i2c_qwiic_pins_default>;
561 clock-frequency = <100000>;
562 status = "okay";
563 };
564
565 &usbss0 {
566 bootph-all;
567 ti,vbus-divider;
568 status = "okay";
569 };
570
571 &usb0 {
572 bootph-all;
573 dr_mode = "peripheral";
574 };
575
576 &usbss1 {
577 ti,vbus-divider;
578 status = "okay";
579 };
580
581 &usb1 {
582 dr_mode = "host";
583 pinctrl-names = "default";
584 pinctrl-0 = <&usb1_pins_default>;
585 };
586
587 &cpsw3g {
588 pinctrl-names = "default";
589 pinctrl-0 = <&rgmii1_pins_default>, <&spe_pins_default>,
590 <&gbe_pmx_obsclk>;
591 assigned-clocks = <&k3_clks 157 70>, <&k3_clks 157 20>;
592 assigned-clock-parents = <&k3_clks 157 72>, <&k3_clks 157 22>;
593 status = "okay";
594 };
595
596 &cpsw_port1 {
597 phy-mode = "rgmii-id";
598 phy-handle = <&cpsw3g_phy0>;
599 };
600
601 &cpsw_port2 {
602 phy-mode = "rmii";
603 phy-handle = <&cpsw3g_phy1>;
604 };
605
606 &cpsw3g_mdio {
607 status = "okay";
608 pinctrl-names = "default";
609 pinctrl-0 = <&mdio0_pins_default>;
610
611 cpsw3g_phy0: ethernet-phy@0 {
612 reg = <0>;
613 reset-gpios = <&main_gpio0 15 GPIO_ACTIVE_LOW>;
614 reset-assert-us = <10000>;
615 reset-deassert-us = <50000>;
616 };
617
618 cpsw3g_phy1: ethernet-phy@1 {
619 reg = <1>;
620 reset-gpios = <&main_gpio1 5 GPIO_ACTIVE_LOW>;
621 reset-assert-us = <25>;
622 reset-deassert-us = <35>;
623 };
624 };
625
626 &main_gpio0 {
627 bootph-all;
628 pinctrl-names = "default";
629 pinctrl-0 = <&gpio0_pins_default>;
630 gpio-line-names = "BL_EN_3V3", "SPE_PO_EN", "RTC_INT", /* 0-2 */
631 "USR0", "USR1", "USR2", "USR3", "", "", "USR4", /* 3-9 */
632 "EEPROM_WP", /* 10 */
633 "CSI2_CAMERA_GPIO1", "CSI2_CAMERA_GPIO2", /* 11-12 */
634 "CC1352P7_BOOT", "CC1352P7_RSTN", "GBE_RSTN", "", "", /* 13-17 */
635 "USR_BUTTON", "", "", "", "", "", "", "", "", /* 18-26 */
636 "", "", "", "", "", "", "", "", "", "HDMI_INT", /* 27-36 */
637 "", "VDD_WLAN_EN", "", "", "WL_IRQ", "GBE_INTN",/* 37-42 */
638 "", "", "", "", "", "", "", "", "", "", "", "", /* 43-54 */
639 "", "", "", "", "", "", "", "", "", "", "", "", /* 55-66 */
640 "", "", "", "", "", "", "", "", "", "", "", "", /* 67-78 */
641 "", "", "", "", "", "", /* 79-84 */
642 "BITBANG_MDIO_DATA", "BITBANG_MDIO_CLK", /* 85-86 */
643 "", "", "", "", ""; /* 87-91 */
644 };
645
646 &main_gpio1 {
647 bootph-all;
648 pinctrl-names = "default";
649 pinctrl-0 = <&mikrobus_gpio_pins_default>;
650 gpio-line-names = "", "", "", "", "", /* 0-4 */
651 "SPE_RSTN", "SPE_INTN", "MIKROBUS_GPIO1_7", /* 5-7 */
652 "MIKROBUS_GPIO1_8", "MIKROBUS_GPIO1_9", /* 8-9 */
653 "MIKROBUS_GPIO1_10", "MIKROBUS_GPIO1_11", /* 10-11 */
654 "MIKROBUS_GPIO1_12", "MIKROBUS_W1_GPIO0", /* 12-13 */
655 "MIKROBUS_GPIO1_14", /* 14 */
656 "", "", "", "", "VDD_3V3_SD", "", "", /* 15-21 */
657 "MIKROBUS_GPIO1_22", "MIKROBUS_GPIO1_23", /* 22-23 */
658 "MIKROBUS_GPIO1_24", "MIKROBUS_GPIO1_25", /* 24-25 */
659 "", "", "", "", "", "", "", "", "", "", "", "", /* 26-37 */
660 "", "", "", "", "", "", "", "", "", "", /* 38-47 */
661 "SD_CD", "SD_VOLT_SEL", "", ""; /* 48-51 */
662 };
663
664 &main_i2c0 {
665 bootph-all;
666 pinctrl-names = "default";
667 pinctrl-0 = <&local_i2c_pins_default>;
668 clock-frequency = <400000>;
669 status = "okay";
670
671 eeprom@50 {
672 compatible = "atmel,24c32";
673 reg = <0x50>;
674 };
675
676 rtc: rtc@68 {
677 compatible = "ti,bq32000";
678 reg = <0x68>;
679 interrupt-parent = <&main_gpio0>;
680 interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
681 };
682
683 tps65219: pmic@30 {
684 bootph-all;
685 compatible = "ti,tps65219";
686 reg = <0x30>;
687 buck1-supply = <&vsys_5v0>;
688 buck2-supply = <&vsys_5v0>;
689 buck3-supply = <&vsys_5v0>;
690 ldo1-supply = <&vdd_3v3>;
691 ldo2-supply = <&buck2_reg>;
692 ldo3-supply = <&vdd_3v3>;
693 ldo4-supply = <&vdd_3v3>;
694
695 pinctrl-names = "default";
696 pinctrl-0 = <&pmic_irq_pins_default>;
697 interrupt-parent = <&gic500>;
698 interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
699 interrupt-controller;
700 #interrupt-cells = <1>;
701
702 system-power-controller;
703 ti,power-button;
704
705 regulators {
706 buck1_reg: buck1 {
707 regulator-name = "VDD_CORE";
708 regulator-min-microvolt = <850000>;
709 regulator-max-microvolt = <850000>;
710 regulator-boot-on;
711 regulator-always-on;
712 };
713
714 buck2_reg: buck2 {
715 regulator-name = "VDD_1V8";
716 regulator-min-microvolt = <1800000>;
717 regulator-max-microvolt = <1800000>;
718 regulator-boot-on;
719 regulator-always-on;
720 };
721
722 buck3_reg: buck3 {
723 regulator-name = "VDD_1V2";
724 regulator-min-microvolt = <1200000>;
725 regulator-max-microvolt = <1200000>;
726 regulator-boot-on;
727 regulator-always-on;
728 };
729
730 ldo1_reg: ldo1 {
731 /*
732 * Regulator is left as is unused, vdd_sd
733 * is controlled via GPIO with bypass config
734 * as per the NVM configuration
735 */
736 regulator-name = "VDD_SD_3V3";
737 regulator-min-microvolt = <3300000>;
738 regulator-max-microvolt = <3300000>;
739 regulator-allow-bypass;
740 regulator-boot-on;
741 regulator-always-on;
742 };
743
744 ldo2_reg: ldo2 {
745 regulator-name = "VDDA_0V85";
746 regulator-min-microvolt = <850000>;
747 regulator-max-microvolt = <850000>;
748 regulator-boot-on;
749 regulator-always-on;
750 };
751
752 ldo3_reg: ldo3 {
753 regulator-name = "VDDA_1V8";
754 regulator-min-microvolt = <1800000>;
755 regulator-max-microvolt = <1800000>;
756 regulator-boot-on;
757 regulator-always-on;
758 };
759
760 ldo4_reg: ldo4 {
761 regulator-name = "VDD_2V5";
762 regulator-min-microvolt = <2500000>;
763 regulator-max-microvolt = <2500000>;
764 regulator-boot-on;
765 regulator-always-on;
766 };
767 };
768 };
769 };
770
771 &main_i2c1 {
772 pinctrl-names = "default";
773 pinctrl-0 = <&grove_pins_default>;
774 clock-frequency = <100000>;
775 status = "okay";
776 };
777
778 &main_i2c2 {
779 pinctrl-names = "default";
780 pinctrl-0 = <&i2c2_1v8_pins_default>;
781 clock-frequency = <100000>;
782 status = "okay";
783
784 it66121: bridge-hdmi@4c {
785 compatible = "ite,it66121";
786 reg = <0x4c>;
787 pinctrl-names = "default";
788 pinctrl-0 = <&hdmi_gpio_pins_default>;
789 vcn33-supply = <&vdd_3v3>;
790 vcn18-supply = <&buck2_reg>;
791 vrf12-supply = <&buck3_reg>;
792 reset-gpios = <&main_gpio0 21 GPIO_ACTIVE_LOW>;
793 interrupt-parent = <&main_gpio0>;
794 interrupts = <36 IRQ_TYPE_EDGE_FALLING>;
795 #sound-dai-cells = <0>;
796
797 ports {
798 #address-cells = <1>;
799 #size-cells = <0>;
800
801 port@0 {
802 reg = <0>;
803
804 it66121_in: endpoint {
805 bus-width = <24>;
806 remote-endpoint = <&dpi1_out>;
807 };
808 };
809
810 port@1 {
811 reg = <1>;
812
813 it66121_out: endpoint {
814 remote-endpoint = <&hdmi_connector_in>;
815 };
816 };
817 };
818 };
819 };
820
821 &main_i2c3 {
822 pinctrl-names = "default";
823 pinctrl-0 = <&mikrobus_i2c_pins_default>;
824 clock-frequency = <400000>;
825 status = "okay";
826 };
827
828 &main_spi2 {
829 pinctrl-names = "default";
830 pinctrl-0 = <&mikrobus_spi_pins_default>;
831 status = "okay";
832 };
833
834 &sdhci0 {
835 bootph-all;
836 non-removable;
837 pinctrl-names = "default";
838 pinctrl-0 = <&emmc_pins_default>;
839 status = "okay";
840 };
841
842 &sdhci1 {
843 /* SD/MMC */
844 bootph-all;
845 pinctrl-names = "default";
846 pinctrl-0 = <&sd_pins_default>;
847
848 vmmc-supply = <&vdd_3v3_sd>;
849 vqmmc-supply = <&vdd_sd_dv>;
850 disable-wp;
851 cd-gpios = <&main_gpio1 48 GPIO_ACTIVE_LOW>;
852 cd-debounce-delay-ms = <100>;
853 ti,fails-without-test-cd;
854 status = "okay";
855 };
856
857 &sdhci2 {
858 pinctrl-names = "default";
859 pinctrl-0 = <&wifi_pins_default>, <&wifi_32k_clk>;
860 non-removable;
861 ti,fails-without-test-cd;
862 cap-power-off-card;
863 keep-power-in-suspend;
864 mmc-pwrseq = <&sdio_pwrseq>;
865 assigned-clocks = <&k3_clks 157 158>;
866 assigned-clock-parents = <&k3_clks 157 160>;
867 #address-cells = <1>;
868 #size-cells = <0>;
869 status = "okay";
870
871 wlcore: wlcore@2 {
872 compatible = "ti,wl1807";
873 reg = <2>;
874 pinctrl-names = "default";
875 pinctrl-0 = <&wifi_wlirq_pins_default>;
876 interrupt-parent = <&main_gpio0>;
877 interrupts = <41 IRQ_TYPE_EDGE_FALLING>;
878 };
879 };
880
881 &main_uart0 {
882 bootph-all;
883 pinctrl-names = "default";
884 pinctrl-0 = <&main_uart0_pins_default>;
885 status = "okay";
886 };
887
888 &main_uart1 {
889 /* Main UART1 is used by TIFS firmware */
890 status = "reserved";
891 };
892
893 &main_uart5 {
894 pinctrl-names = "default";
895 pinctrl-0 = <&mikrobus_uart_pins_default>;
896 status = "okay";
897 };
898
899 &main_uart6 {
900 pinctrl-names = "default";
901 pinctrl-0 = <&wifi_debug_uart_pins_default>;
902 status = "okay";
903
904 mcu {
905 compatible = "ti,cc1352p7";
906 bootloader-backdoor-gpios = <&main_gpio0 13 GPIO_ACTIVE_HIGH>;
907 reset-gpios = <&main_gpio0 14 GPIO_ACTIVE_HIGH>;
908 vdds-supply = <&vdd_3v3>;
909 };
910 };
911
912 &dss {
913 status = "okay";
914 pinctrl-names = "default";
915 pinctrl-0 = <&dss0_pins_default>;
916 };
917
918 &dss_ports {
919 /* VP2: DPI Output */
920 port@1 {
921 reg = <1>;
922
923 dpi1_out: endpoint {
924 remote-endpoint = <&it66121_in>;
925 };
926 };
927 };
928
929 &mcasp1 {
930 status = "okay";
931 #sound-dai-cells = <0>;
932 pinctrl-names = "default";
933 pinctrl-0 = <&mcasp_hdmi_pins_default>;
934 auxclk-fs-ratio = <2177>;
935 op-mode = <0>; /* MCASP_IIS_MODE */
936 tdm-slots = <2>;
937 serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
938 1 0 0 0
939 0 0 0 0
940 0 0 0 0
941 0 0 0 0
942 >;
943 };
944
945 &ecap2 {
946 status = "okay";
947 pinctrl-names = "default";
948 pinctrl-0 = <&mikrobus_pwm_pins_default>;
949 };