| 1 |
// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) |
| 2 |
/* |
| 3 |
* Copyright (C) STMicroelectronics 2023 - All Rights Reserved |
| 4 |
* Author: Alexandre Torgue <[email protected]> for STMicroelectronics. |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
|
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/leds/common.h> |
| 11 |
#include <dt-bindings/regulator/st,stm32mp25-regulator.h> |
| 12 |
#include "stm32mp257.dtsi" |
| 13 |
#include "stm32mp25xf.dtsi" |
| 14 |
#include "stm32mp25-pinctrl.dtsi" |
| 15 |
#include "stm32mp25xxai-pinctrl.dtsi" |
| 16 |
|
| 17 |
/ { |
| 18 |
model = "STMicroelectronics STM32MP257F-EV1 Evaluation Board"; |
| 19 |
compatible = "st,stm32mp257f-ev1", "st,stm32mp257"; |
| 20 |
|
| 21 |
aliases { |
| 22 |
ethernet0 = ðernet2; |
| 23 |
ethernet1 = ðernet1; |
| 24 |
serial0 = &usart2; |
| 25 |
serial1 = &usart6; |
| 26 |
}; |
| 27 |
|
| 28 |
chosen { |
| 29 |
stdout-path = "serial0:115200n8"; |
| 30 |
}; |
| 31 |
|
| 32 |
clocks { |
| 33 |
clk_ext_camera: clk-ext-camera { |
| 34 |
#clock-cells = <0>; |
| 35 |
compatible = "fixed-clock"; |
| 36 |
clock-frequency = <24000000>; |
| 37 |
}; |
| 38 |
|
| 39 |
pad_clk: pad-clk { |
| 40 |
#clock-cells = <0>; |
| 41 |
compatible = "fixed-clock"; |
| 42 |
clock-frequency = <100000000>; |
| 43 |
}; |
| 44 |
}; |
| 45 |
|
| 46 |
gpio-leds { |
| 47 |
compatible = "gpio-leds"; |
| 48 |
|
| 49 |
led_blue: led-blue { |
| 50 |
function = LED_FUNCTION_HEARTBEAT; |
| 51 |
color = <LED_COLOR_ID_BLUE>; |
| 52 |
gpios = <&gpioj 7 GPIO_ACTIVE_HIGH>; |
| 53 |
linux,default-trigger = "heartbeat"; |
| 54 |
default-state = "off"; |
| 55 |
}; |
| 56 |
|
| 57 |
led-green { |
| 58 |
color = <LED_COLOR_ID_GREEN>; |
| 59 |
gpios = <&gpiod 8 GPIO_ACTIVE_HIGH>; |
| 60 |
}; |
| 61 |
|
| 62 |
led-orange { |
| 63 |
color = <LED_COLOR_ID_ORANGE>; |
| 64 |
gpios = <&gpioj 6 GPIO_ACTIVE_HIGH>; |
| 65 |
}; |
| 66 |
}; |
| 67 |
|
| 68 |
ddr_channel: sdram-channel-0 { |
| 69 |
#address-cells = <1>; |
| 70 |
#size-cells = <0>; |
| 71 |
compatible = "jedec,ddr4-channel"; |
| 72 |
io-width = <32>; |
| 73 |
}; |
| 74 |
|
| 75 |
imx335_2v9: regulator-2v9 { |
| 76 |
compatible = "regulator-fixed"; |
| 77 |
regulator-name = "imx335-avdd"; |
| 78 |
regulator-min-microvolt = <2900000>; |
| 79 |
regulator-max-microvolt = <2900000>; |
| 80 |
regulator-always-on; |
| 81 |
}; |
| 82 |
|
| 83 |
imx335_1v8: regulator-1v8 { |
| 84 |
compatible = "regulator-fixed"; |
| 85 |
regulator-name = "imx335-ovdd"; |
| 86 |
regulator-min-microvolt = <1800000>; |
| 87 |
regulator-max-microvolt = <1800000>; |
| 88 |
regulator-always-on; |
| 89 |
}; |
| 90 |
|
| 91 |
imx335_1v2: regulator-1v2 { |
| 92 |
compatible = "regulator-fixed"; |
| 93 |
regulator-name = "imx335-dvdd"; |
| 94 |
regulator-min-microvolt = <1200000>; |
| 95 |
regulator-max-microvolt = <1200000>; |
| 96 |
regulator-always-on; |
| 97 |
}; |
| 98 |
|
| 99 |
memory@80000000 { |
| 100 |
device_type = "memory"; |
| 101 |
reg = <0x0 0x80000000 0x1 0x0>; |
| 102 |
}; |
| 103 |
|
| 104 |
options { |
| 105 |
u-boot { |
| 106 |
compatible = "u-boot,config"; |
| 107 |
boot-led = <&led_blue>; |
| 108 |
}; |
| 109 |
}; |
| 110 |
|
| 111 |
panel_lvds: display { |
| 112 |
compatible = "edt,etml0700z9ndha", "panel-lvds"; |
| 113 |
enable-gpios = <&gpiog 15 GPIO_ACTIVE_HIGH>; |
| 114 |
backlight = <&panel_lvds_backlight>; |
| 115 |
power-supply = <&scmi_v3v3>; |
| 116 |
width-mm = <156>; |
| 117 |
height-mm = <92>; |
| 118 |
data-mapping = "vesa-24"; |
| 119 |
status = "okay"; |
| 120 |
|
| 121 |
panel-timing { |
| 122 |
clock-frequency = <54000000>; |
| 123 |
hactive = <1024>; |
| 124 |
vactive = <600>; |
| 125 |
hfront-porch = <150>; |
| 126 |
hback-porch = <150>; |
| 127 |
hsync-len = <21>; |
| 128 |
vfront-porch = <24>; |
| 129 |
vback-porch = <24>; |
| 130 |
vsync-len = <21>; |
| 131 |
}; |
| 132 |
|
| 133 |
port { |
| 134 |
lvds_panel_in: endpoint { |
| 135 |
remote-endpoint = <&lvds_out0>; |
| 136 |
}; |
| 137 |
}; |
| 138 |
}; |
| 139 |
|
| 140 |
panel_lvds_backlight: backlight { |
| 141 |
compatible = "gpio-backlight"; |
| 142 |
gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>; |
| 143 |
default-on; |
| 144 |
status = "okay"; |
| 145 |
}; |
| 146 |
|
| 147 |
reserved-memory { |
| 148 |
#address-cells = <2>; |
| 149 |
#size-cells = <2>; |
| 150 |
ranges; |
| 151 |
|
| 152 |
fw@80000000 { |
| 153 |
compatible = "shared-dma-pool"; |
| 154 |
reg = <0x0 0x80000000 0x0 0x4000000>; |
| 155 |
no-map; |
| 156 |
}; |
| 157 |
|
| 158 |
mm_ospi1: mm-ospi@60000000 { |
| 159 |
reg = <0x0 0x60000000 0x0 0x10000000>; |
| 160 |
no-map; |
| 161 |
}; |
| 162 |
}; |
| 163 |
}; |
| 164 |
|
| 165 |
&arm_wdt { |
| 166 |
timeout-sec = <32>; |
| 167 |
status = "okay"; |
| 168 |
}; |
| 169 |
|
| 170 |
&combophy { |
| 171 |
clocks = <&rcc CK_BUS_USB3PCIEPHY>, <&rcc CK_KER_USB3PCIEPHY>, <&pad_clk>; |
| 172 |
clock-names = "apb", "ker", "pad"; |
| 173 |
status = "okay"; |
| 174 |
}; |
| 175 |
|
| 176 |
&csi { |
| 177 |
vdd-supply = <&scmi_vddcore>; |
| 178 |
vdda18-supply = <&scmi_v1v8>; |
| 179 |
status = "okay"; |
| 180 |
ports { |
| 181 |
#address-cells = <1>; |
| 182 |
#size-cells = <0>; |
| 183 |
port@0 { |
| 184 |
reg = <0>; |
| 185 |
csi_sink: endpoint { |
| 186 |
remote-endpoint = <&imx335_ep>; |
| 187 |
data-lanes = <1 2>; |
| 188 |
bus-type = <4>; |
| 189 |
}; |
| 190 |
}; |
| 191 |
port@1 { |
| 192 |
reg = <1>; |
| 193 |
csi_source: endpoint { |
| 194 |
remote-endpoint = <&dcmipp_0>; |
| 195 |
}; |
| 196 |
}; |
| 197 |
}; |
| 198 |
}; |
| 199 |
|
| 200 |
&dcmipp { |
| 201 |
status = "okay"; |
| 202 |
port { |
| 203 |
dcmipp_0: endpoint { |
| 204 |
remote-endpoint = <&csi_source>; |
| 205 |
bus-type = <4>; |
| 206 |
}; |
| 207 |
}; |
| 208 |
}; |
| 209 |
|
| 210 |
ðernet1 { |
| 211 |
pinctrl-0 = <ð1_rgmii_pins_a ð1_mdio_pins_a>; |
| 212 |
pinctrl-1 = <ð1_rgmii_sleep_pins_a ð1_mdio_sleep_pins_a>; |
| 213 |
pinctrl-names = "default", "sleep"; |
| 214 |
phy-handle = <&phy1_eth1>; |
| 215 |
phy-mode = "rgmii-id"; |
| 216 |
st,ext-phyclk; |
| 217 |
status = "okay"; |
| 218 |
|
| 219 |
mdio { |
| 220 |
#address-cells = <1>; |
| 221 |
#size-cells = <0>; |
| 222 |
compatible = "snps,dwmac-mdio"; |
| 223 |
phy1_eth1: ethernet-phy@4 { |
| 224 |
compatible = "ethernet-phy-id001c.c916"; |
| 225 |
reg = <4>; |
| 226 |
reset-gpios = <&gpioj 9 GPIO_ACTIVE_LOW>; |
| 227 |
reset-assert-us = <10000>; |
| 228 |
reset-deassert-us = <80000>; |
| 229 |
}; |
| 230 |
}; |
| 231 |
}; |
| 232 |
|
| 233 |
ðernet2 { |
| 234 |
pinctrl-names = "default", "sleep"; |
| 235 |
pinctrl-0 = <ð2_rgmii_pins_a>; |
| 236 |
pinctrl-1 = <ð2_rgmii_sleep_pins_a>; |
| 237 |
max-speed = <1000>; |
| 238 |
phy-handle = <&phy0_eth2>; |
| 239 |
phy-mode = "rgmii-id"; |
| 240 |
status = "okay"; |
| 241 |
|
| 242 |
mdio { |
| 243 |
#address-cells = <1>; |
| 244 |
#size-cells = <0>; |
| 245 |
compatible = "snps,dwmac-mdio"; |
| 246 |
phy0_eth2: ethernet-phy@1 { |
| 247 |
compatible = "ethernet-phy-id001c.c916"; |
| 248 |
reg = <1>; |
| 249 |
reset-assert-us = <10000>; |
| 250 |
reset-deassert-us = <300>; |
| 251 |
reset-gpios = <&gpiog 6 GPIO_ACTIVE_LOW>; |
| 252 |
}; |
| 253 |
}; |
| 254 |
}; |
| 255 |
|
| 256 |
&i2c2 { |
| 257 |
pinctrl-names = "default", "sleep"; |
| 258 |
pinctrl-0 = <&i2c2_pins_a>; |
| 259 |
pinctrl-1 = <&i2c2_sleep_pins_a>; |
| 260 |
i2c-scl-rising-time-ns = <100>; |
| 261 |
i2c-scl-falling-time-ns = <13>; |
| 262 |
clock-frequency = <400000>; |
| 263 |
status = "okay"; |
| 264 |
|
| 265 |
imx335: camera@1a { |
| 266 |
compatible = "sony,imx335"; |
| 267 |
reg = <0x1a>; |
| 268 |
clocks = <&clk_ext_camera>; |
| 269 |
avdd-supply = <&imx335_2v9>; |
| 270 |
ovdd-supply = <&imx335_1v8>; |
| 271 |
dvdd-supply = <&imx335_1v2>; |
| 272 |
reset-gpios = <&gpioi 7 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; |
| 273 |
|
| 274 |
port { |
| 275 |
imx335_ep: endpoint { |
| 276 |
remote-endpoint = <&csi_sink>; |
| 277 |
clock-lanes = <0>; |
| 278 |
data-lanes = <1 2>; |
| 279 |
link-frequencies = /bits/ 64 <594000000>; |
| 280 |
}; |
| 281 |
}; |
| 282 |
}; |
| 283 |
|
| 284 |
ili2511: ili2511@41 { |
| 285 |
compatible = "ilitek,ili251x"; |
| 286 |
reg = <0x41>; |
| 287 |
interrupt-parent = <&gpioi>; |
| 288 |
interrupts = <13 IRQ_TYPE_EDGE_FALLING>; |
| 289 |
reset-gpios = <&gpiog 14 GPIO_ACTIVE_LOW>; |
| 290 |
status = "okay"; |
| 291 |
}; |
| 292 |
}; |
| 293 |
|
| 294 |
&i2c8 { |
| 295 |
pinctrl-names = "default", "sleep"; |
| 296 |
pinctrl-0 = <&i2c8_pins_a>; |
| 297 |
pinctrl-1 = <&i2c8_sleep_pins_a>; |
| 298 |
i2c-scl-rising-time-ns = <57>; |
| 299 |
i2c-scl-falling-time-ns = <7>; |
| 300 |
clock-frequency = <400000>; |
| 301 |
status = "disabled"; |
| 302 |
}; |
| 303 |
|
| 304 |
&ommanager { |
| 305 |
memory-region = <&mm_ospi1>; |
| 306 |
memory-region-names = "ospi1"; |
| 307 |
pinctrl-0 = <&ospi_port1_clk_pins_a |
| 308 |
&ospi_port1_io03_pins_a |
| 309 |
&ospi_port1_cs0_pins_a>; |
| 310 |
pinctrl-1 = <&ospi_port1_clk_sleep_pins_a |
| 311 |
&ospi_port1_io03_sleep_pins_a |
| 312 |
&ospi_port1_cs0_sleep_pins_a>; |
| 313 |
pinctrl-names = "default", "sleep"; |
| 314 |
status = "okay"; |
| 315 |
|
| 316 |
spi@0 { |
| 317 |
#address-cells = <1>; |
| 318 |
#size-cells = <0>; |
| 319 |
memory-region = <&mm_ospi1>; |
| 320 |
status = "okay"; |
| 321 |
|
| 322 |
flash0: flash@0 { |
| 323 |
compatible = "jedec,spi-nor"; |
| 324 |
reg = <0>; |
| 325 |
spi-rx-bus-width = <4>; |
| 326 |
spi-tx-bus-width = <4>; |
| 327 |
spi-max-frequency = <50000000>; |
| 328 |
}; |
| 329 |
}; |
| 330 |
}; |
| 331 |
|
| 332 |
/* use LPTIMER with tick broadcast for suspend mode */ |
| 333 |
&lptimer3 { |
| 334 |
status = "okay"; |
| 335 |
timer { |
| 336 |
status = "okay"; |
| 337 |
}; |
| 338 |
}; |
| 339 |
|
| 340 |
<dc { |
| 341 |
status = "okay"; |
| 342 |
port { |
| 343 |
ltdc_ep0_out: endpoint { |
| 344 |
remote-endpoint = <&lvds_in>; |
| 345 |
}; |
| 346 |
}; |
| 347 |
}; |
| 348 |
|
| 349 |
&lvds { |
| 350 |
status = "okay"; |
| 351 |
ports { |
| 352 |
#address-cells = <1>; |
| 353 |
#size-cells = <0>; |
| 354 |
|
| 355 |
port@0 { |
| 356 |
reg = <0>; |
| 357 |
lvds_in: endpoint { |
| 358 |
remote-endpoint = <<dc_ep0_out>; |
| 359 |
}; |
| 360 |
}; |
| 361 |
|
| 362 |
port@1 { |
| 363 |
reg = <1>; |
| 364 |
lvds_out0: endpoint { |
| 365 |
remote-endpoint = <&lvds_panel_in>; |
| 366 |
}; |
| 367 |
}; |
| 368 |
}; |
| 369 |
}; |
| 370 |
|
| 371 |
&pcie_ep { |
| 372 |
pinctrl-names = "default", "init"; |
| 373 |
pinctrl-0 = <&pcie_pins_a>; |
| 374 |
pinctrl-1 = <&pcie_init_pins_a>; |
| 375 |
reset-gpios = <&gpioj 8 GPIO_ACTIVE_LOW>; |
| 376 |
status = "disabled"; |
| 377 |
}; |
| 378 |
|
| 379 |
&pcie_rc { |
| 380 |
pinctrl-names = "default", "init", "sleep"; |
| 381 |
pinctrl-0 = <&pcie_pins_a>; |
| 382 |
pinctrl-1 = <&pcie_init_pins_a>; |
| 383 |
pinctrl-2 = <&pcie_sleep_pins_a>; |
| 384 |
status = "okay"; |
| 385 |
|
| 386 |
pcie@0,0 { |
| 387 |
reset-gpios = <&gpioj 8 GPIO_ACTIVE_LOW>; |
| 388 |
wake-gpios = <&gpioh 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| 389 |
}; |
| 390 |
}; |
| 391 |
|
| 392 |
&rtc { |
| 393 |
status = "okay"; |
| 394 |
}; |
| 395 |
|
| 396 |
&scmi_regu { |
| 397 |
scmi_vddio1: regulator@0 { |
| 398 |
regulator-min-microvolt = <1800000>; |
| 399 |
regulator-max-microvolt = <3300000>; |
| 400 |
}; |
| 401 |
scmi_vddcore: regulator@11 { |
| 402 |
reg = <VOLTD_SCMI_STPMIC2_BUCK2>; |
| 403 |
regulator-name = "vddcore"; |
| 404 |
}; |
| 405 |
scmi_v1v8: regulator@14 { |
| 406 |
reg = <VOLTD_SCMI_STPMIC2_BUCK5>; |
| 407 |
regulator-name = "v1v8"; |
| 408 |
}; |
| 409 |
scmi_v3v3: regulator@16 { |
| 410 |
reg = <VOLTD_SCMI_STPMIC2_BUCK7>; |
| 411 |
regulator-name = "v3v3"; |
| 412 |
}; |
| 413 |
scmi_vdd_emmc: regulator@18 { |
| 414 |
reg = <VOLTD_SCMI_STPMIC2_LDO2>; |
| 415 |
regulator-name = "vdd_emmc"; |
| 416 |
}; |
| 417 |
scmi_vdd3v3_usb: regulator@20 { |
| 418 |
reg = <VOLTD_SCMI_STPMIC2_LDO4>; |
| 419 |
regulator-name = "vdd3v3_usb"; |
| 420 |
}; |
| 421 |
scmi_vdd_sdcard: regulator@23 { |
| 422 |
reg = <VOLTD_SCMI_STPMIC2_LDO7>; |
| 423 |
regulator-name = "vdd_sdcard"; |
| 424 |
}; |
| 425 |
}; |
| 426 |
|
| 427 |
&sdmmc1 { |
| 428 |
pinctrl-names = "default", "opendrain", "sleep"; |
| 429 |
pinctrl-0 = <&sdmmc1_b4_pins_a>; |
| 430 |
pinctrl-1 = <&sdmmc1_b4_od_pins_a>; |
| 431 |
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; |
| 432 |
cd-gpios = <&gpiod 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| 433 |
disable-wp; |
| 434 |
st,neg-edge; |
| 435 |
bus-width = <4>; |
| 436 |
vmmc-supply = <&scmi_vdd_sdcard>; |
| 437 |
vqmmc-supply = <&scmi_vddio1>; |
| 438 |
status = "okay"; |
| 439 |
}; |
| 440 |
|
| 441 |
&spi3 { |
| 442 |
pinctrl-names = "default", "sleep"; |
| 443 |
pinctrl-0 = <&spi3_pins_a>; |
| 444 |
pinctrl-1 = <&spi3_sleep_pins_a>; |
| 445 |
status = "disabled"; |
| 446 |
}; |
| 447 |
|
| 448 |
&spi8 { |
| 449 |
pinctrl-names = "default", "sleep"; |
| 450 |
pinctrl-0 = <&spi8_pins_a>; |
| 451 |
pinctrl-1 = <&spi8_sleep_pins_a>; |
| 452 |
status = "disabled"; |
| 453 |
}; |
| 454 |
|
| 455 |
&timers3 { |
| 456 |
status = "disabled"; |
| 457 |
counter { |
| 458 |
status = "okay"; |
| 459 |
}; |
| 460 |
pwm { |
| 461 |
pinctrl-0 = <&pwm3_pins_a>; |
| 462 |
pinctrl-1 = <&pwm3_sleep_pins_a>; |
| 463 |
pinctrl-names = "default", "sleep"; |
| 464 |
status = "okay"; |
| 465 |
}; |
| 466 |
timer@2 { |
| 467 |
status = "okay"; |
| 468 |
}; |
| 469 |
}; |
| 470 |
|
| 471 |
&timers8 { |
| 472 |
status = "disabled"; |
| 473 |
counter { |
| 474 |
status = "okay"; |
| 475 |
}; |
| 476 |
pwm { |
| 477 |
pinctrl-0 = <&pwm8_pins_a>; |
| 478 |
pinctrl-1 = <&pwm8_sleep_pins_a>; |
| 479 |
pinctrl-names = "default", "sleep"; |
| 480 |
status = "okay"; |
| 481 |
}; |
| 482 |
timer@7 { |
| 483 |
status = "okay"; |
| 484 |
}; |
| 485 |
}; |
| 486 |
|
| 487 |
&timers10 { |
| 488 |
status = "disabled"; |
| 489 |
counter { |
| 490 |
pinctrl-0 = <&tim10_counter_pins_a>; |
| 491 |
pinctrl-1 = <&tim10_counter_sleep_pins_a>; |
| 492 |
pinctrl-names = "default", "sleep"; |
| 493 |
status = "okay"; |
| 494 |
}; |
| 495 |
}; |
| 496 |
|
| 497 |
&timers12 { |
| 498 |
status = "disabled"; |
| 499 |
counter { |
| 500 |
status = "okay"; |
| 501 |
}; |
| 502 |
pwm { |
| 503 |
pinctrl-0 = <&pwm12_pins_a>; |
| 504 |
pinctrl-1 = <&pwm12_sleep_pins_a>; |
| 505 |
pinctrl-names = "default", "sleep"; |
| 506 |
status = "okay"; |
| 507 |
}; |
| 508 |
timer@11 { |
| 509 |
status = "okay"; |
| 510 |
}; |
| 511 |
}; |
| 512 |
|
| 513 |
&usart2 { |
| 514 |
pinctrl-names = "default", "idle", "sleep"; |
| 515 |
pinctrl-0 = <&usart2_pins_a>; |
| 516 |
pinctrl-1 = <&usart2_idle_pins_a>; |
| 517 |
pinctrl-2 = <&usart2_sleep_pins_a>; |
| 518 |
/delete-property/dmas; |
| 519 |
/delete-property/dma-names; |
| 520 |
status = "okay"; |
| 521 |
}; |
| 522 |
|
| 523 |
&usart6 { |
| 524 |
pinctrl-names = "default", "idle", "sleep"; |
| 525 |
pinctrl-0 = <&usart6_pins_a>; |
| 526 |
pinctrl-1 = <&usart6_idle_pins_a>; |
| 527 |
pinctrl-2 = <&usart6_sleep_pins_a>; |
| 528 |
uart-has-rtscts; |
| 529 |
status = "disabled"; |
| 530 |
}; |