| 1 |
// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT) |
| 2 |
/* |
| 3 |
* Copyright (c) 2024 Cherry Embedded Solutions GmbH |
| 4 |
* |
| 5 |
* Device Tree Overlay for the Pre-ICT tester adapter for the Mezzanine |
| 6 |
* connector on RK3588 Jaguar. |
| 7 |
* |
| 8 |
* This adapter has a PCIe Gen2 x1 M.2 M-Key connector and two proprietary |
| 9 |
* camera connectors (each their own I2C bus, clock, reset and PWM lines as well |
| 10 |
* as 2-lane CSI). |
| 11 |
* |
| 12 |
* This adapter routes some GPIOs to power rails and loops together some other |
| 13 |
* GPIOs. |
| 14 |
* |
| 15 |
* This adapter is used during manufacturing for validating proper soldering of |
| 16 |
* the mezzanine connector. |
| 17 |
*/ |
| 18 |
|
| 19 |
/dts-v1/; |
| 20 |
/plugin/; |
| 21 |
|
| 22 |
#include <dt-bindings/gpio/gpio.h> |
| 23 |
#include <dt-bindings/pinctrl/rockchip.h> |
| 24 |
|
| 25 |
&{/} { |
| 26 |
pre_ict_tester_vcc_1v2: regulator-pre-ict-tester-vcc-1v2 { |
| 27 |
compatible = "regulator-fixed"; |
| 28 |
regulator-name = "pre_ict_tester_vcc_1v2"; |
| 29 |
regulator-always-on; |
| 30 |
regulator-boot-on; |
| 31 |
regulator-min-microvolt = <1200000>; |
| 32 |
regulator-max-microvolt = <1200000>; |
| 33 |
vin-supply = <&vcc_3v3_s3>; |
| 34 |
}; |
| 35 |
|
| 36 |
pre_ict_tester_vcc_2v8: regulator-pre-ict-tester-vcc-2v8 { |
| 37 |
compatible = "regulator-fixed"; |
| 38 |
regulator-name = "pre_ict_tester_vcc_2v8"; |
| 39 |
regulator-always-on; |
| 40 |
regulator-boot-on; |
| 41 |
regulator-min-microvolt = <2800000>; |
| 42 |
regulator-max-microvolt = <2800000>; |
| 43 |
vin-supply = <&vcc_3v3_s3>; |
| 44 |
}; |
| 45 |
}; |
| 46 |
|
| 47 |
&combphy0_ps { |
| 48 |
status = "okay"; |
| 49 |
}; |
| 50 |
|
| 51 |
&gpio3 { |
| 52 |
pinctrl-0 = <&pre_ict_pwr2gpio>; |
| 53 |
pinctrl-names = "default"; |
| 54 |
}; |
| 55 |
|
| 56 |
&pcie2x1l2 { |
| 57 |
pinctrl-names = "default"; |
| 58 |
pinctrl-0 = <&pcie2x1l2_perstn_m0>; |
| 59 |
reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>; /* PCIE20X1_2_PERSTN_M0 */ |
| 60 |
vpcie3v3-supply = <&vcc_3v3_s3>; |
| 61 |
status = "okay"; |
| 62 |
}; |
| 63 |
|
| 64 |
&pinctrl { |
| 65 |
pcie2x1l2 { |
| 66 |
pcie2x1l2_perstn_m0: pcie2x1l2-perstn-m0 { |
| 67 |
rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>; |
| 68 |
}; |
| 69 |
}; |
| 70 |
|
| 71 |
pre-ict-tester { |
| 72 |
pre_ict_pwr2gpio: pre-ict-pwr2gpio-pins { |
| 73 |
rockchip,pins = |
| 74 |
/* |
| 75 |
* GPIO3_A3 requires two power rails to be properly |
| 76 |
* routed to the mezzanine connector to report a proper |
| 77 |
* value: VCC_1V8_S0_1 and VCC_IN_2. It may report an |
| 78 |
* incorrect value if VCC_1V8_S0_1 isn't properly routed, |
| 79 |
* but GPIO3_C6 would catch this HW soldering issue. |
| 80 |
* If VCC_IN_2 is properly routed, GPIO3_A3 should be |
| 81 |
* LOW. The signal shall not read HIGH in the event |
| 82 |
* GPIO3_A3 isn't properly routed due to soldering |
| 83 |
* issue. Therefore, let's enforce a pull-up (which is |
| 84 |
* the SoC default for this pin). |
| 85 |
*/ |
| 86 |
<3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>, |
| 87 |
/* |
| 88 |
* GPIO3_A4 is directly routed to VCC_1V8_S0_2 power |
| 89 |
* rail. It should be HIGH if all is properly soldered. |
| 90 |
* To guarantee that, a pull-down is enforced (which is |
| 91 |
* the SoC default for this pin) so that LOW is read if |
| 92 |
* the loop doesn't exist on HW (soldering issue on |
| 93 |
* either signals). |
| 94 |
*/ |
| 95 |
<3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>, |
| 96 |
/* |
| 97 |
* GPIO3_B2 requires two power rails to be properly |
| 98 |
* routed to the mezzanine connector to report a proper |
| 99 |
* value: VCC_1V8_S0_1 and VCC_IN_1. It may report an |
| 100 |
* incorrect value if VCC_1V8_S0_1 isn't properly routed, |
| 101 |
* but GPIO3_C6 would catch this HW soldering issue. |
| 102 |
* If VCC_IN_1 is properly routed, GPIO3_B2 should be |
| 103 |
* LOW. This is an issue if GPIO3_B2 isn't properly |
| 104 |
* routed due to soldering issue, because GPIO3_B2 |
| 105 |
* default bias is pull-down therefore being LOW. So |
| 106 |
* the worst case scenario and the pass scenario expect |
| 107 |
* the same value. Make GPIO3_B2 a pull-up so that a |
| 108 |
* soldering issue on GPIO3_B2 reports HIGH but proper |
| 109 |
* soldering reports LOW. |
| 110 |
*/ |
| 111 |
<3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>, |
| 112 |
/* |
| 113 |
* GPIO3_C6 is directly routed to VCC_1V8_S0_1 power |
| 114 |
* rail. It should be HIGH if all is properly soldered. |
| 115 |
* This is an issue if GPIO3_C6 or VCC_1V8_S0_1 isn't |
| 116 |
* properly routed due to soldering issue, because |
| 117 |
* GPIO3_C6 default bias is pull-up therefore being HIGH |
| 118 |
* in all cases: |
| 119 |
* - GPIO3_C6 is floating (so HIGH) if GPIO3_C6 is not |
| 120 |
* routed properly, |
| 121 |
* - GPIO3_C6 is floating (so HIGH) if VCC_1V8_S0_1 is |
| 122 |
* not routed properly, |
| 123 |
* - GPIO3_C6 is HIGH if everything is proper, |
| 124 |
* Make GPIO3_C6 a pull-down so that a soldering issue |
| 125 |
* on GPIO3_C6 or VCC_1V8_S0_1 reports LOW but proper |
| 126 |
* soldering reports HIGH. |
| 127 |
*/ |
| 128 |
<3 RK_PC6 RK_FUNC_GPIO &pcfg_pull_down>, |
| 129 |
/* |
| 130 |
* GPIO3_D2 is routed to VCC_5V0_1 power rail through a |
| 131 |
* voltage divider on the adapter. |
| 132 |
* It should be HIGH if all is properly soldered. |
| 133 |
* To guarantee that, a pull-down is enforced (which is |
| 134 |
* the SoC default for this pin) so that LOW is read if |
| 135 |
* the loop doesn't exist on HW (soldering issue on |
| 136 |
* either signals). |
| 137 |
*/ |
| 138 |
<3 RK_PD2 RK_FUNC_GPIO &pcfg_pull_down>, |
| 139 |
/* |
| 140 |
* GPIO3_D3 is routed to VCC_5V0_2 power rail through a |
| 141 |
* voltage divider on the adapter. |
| 142 |
* It should be HIGH if all is properly soldered. |
| 143 |
* To guarantee that, a pull-down is enforced (which is |
| 144 |
* the SoC default for this pin) so that LOW is read if |
| 145 |
* the loop doesn't exist on HW (soldering issue on |
| 146 |
* either signals). |
| 147 |
*/ |
| 148 |
<3 RK_PD3 RK_FUNC_GPIO &pcfg_pull_down>, |
| 149 |
/* |
| 150 |
* GPIO3_D4 is routed to VCC_3V3_S3_1 power rail through |
| 151 |
* a voltage divider on the adapter. |
| 152 |
* It should be HIGH if all is properly soldered. |
| 153 |
* To guarantee that, a pull-down is enforced (which is |
| 154 |
* the SoC default for this pin) so that LOW is read if |
| 155 |
* the loop doesn't exist on HW (soldering issue on |
| 156 |
* either signals). |
| 157 |
*/ |
| 158 |
<3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_down>, |
| 159 |
/* |
| 160 |
* GPIO3_D5 is routed to VCC_3V3_S3_2 power rail through |
| 161 |
* a voltage divider on the adapter. |
| 162 |
* It should be HIGH if all is properly soldered. |
| 163 |
* To guarantee that, a pull-down is enforced (which is |
| 164 |
* the SoC default for this pin) so that LOW is read if |
| 165 |
* the loop doesn't exist on HW (soldering issue on |
| 166 |
* either signals). |
| 167 |
*/ |
| 168 |
<3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_down>; |
| 169 |
}; |
| 170 |
}; |
| 171 |
}; |