| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Copyright (c) 2025 Cherry Embedded Solutions GmbH |
| 4 |
* |
| 5 |
* Device Tree Overlay for the Ethernet Switch adapter for the Mezzanine |
| 6 |
* connector on RK3588 Jaguar |
| 7 |
* (manual: https://embedded.cherry.de/jaguar-ethernet-switch-user-manual/) |
| 8 |
* |
| 9 |
* This adapter has a KSZ9896 Ethernet Switch with 4 1GbE Ethernet connectors, |
| 10 |
* two user controllable LEDs, and an M12 12-pin connector which exposes the |
| 11 |
* following signals: |
| 12 |
* - RS232/RS485 (max 250Kbps/500Kbps, RX pin1, TX pin2) |
| 13 |
* - two digital inputs (pin4 routed to GPIO3_C5 on SoC, pin5 to GPIO4_B4) |
| 14 |
* - two digital outputs (pin7 routed to GPIO3_D3 on SoC, pin8 to GPIO3_D1) |
| 15 |
* - two analog inputs (pin10 to channel1 of ADS1015, pin11 to channel2) |
| 16 |
* |
| 17 |
* RK3588 Jaguar can be powered entirely through the adapter via the M8 3-pin |
| 18 |
* connector (12-24V). |
| 19 |
*/ |
| 20 |
|
| 21 |
/dts-v1/; |
| 22 |
/plugin/; |
| 23 |
|
| 24 |
#include <dt-bindings/clock/rockchip,rk3588-cru.h> |
| 25 |
#include <dt-bindings/gpio/gpio.h> |
| 26 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 27 |
#include <dt-bindings/leds/common.h> |
| 28 |
#include <dt-bindings/pinctrl/rockchip.h> |
| 29 |
|
| 30 |
&{/} { |
| 31 |
aliases { |
| 32 |
ethernet1 = "/ethernet@fe1c0000"; |
| 33 |
}; |
| 34 |
|
| 35 |
mezzanine-leds { |
| 36 |
compatible = "gpio-leds"; |
| 37 |
pinctrl-names = "default"; |
| 38 |
pinctrl-0 = <&led_usr1_pin &led_usr2_pin>; |
| 39 |
|
| 40 |
led-1 { |
| 41 |
gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>; |
| 42 |
label = "USR1"; |
| 43 |
}; |
| 44 |
|
| 45 |
led-2 { |
| 46 |
gpios = <&gpio3 RK_PC4 GPIO_ACTIVE_HIGH>; |
| 47 |
label = "USR2"; |
| 48 |
}; |
| 49 |
}; |
| 50 |
}; |
| 51 |
|
| 52 |
&gmac1 { |
| 53 |
clock_in_out = "output"; |
| 54 |
phy-mode = "rgmii-id"; |
| 55 |
pinctrl-names = "default"; |
| 56 |
pinctrl-0 = <&gmac1_rx_bus2 |
| 57 |
&gmac1_tx_bus2 |
| 58 |
&gmac1_rgmii_clk |
| 59 |
&gmac1_rgmii_bus |
| 60 |
ð1_pins>; |
| 61 |
rx_delay = <0x0>; |
| 62 |
tx_delay = <0x0>; |
| 63 |
status = "okay"; |
| 64 |
|
| 65 |
fixed-link { |
| 66 |
speed = <1000>; |
| 67 |
full-duplex; |
| 68 |
}; |
| 69 |
}; |
| 70 |
|
| 71 |
&i2c1 { |
| 72 |
#address-cells = <1>; |
| 73 |
/* |
| 74 |
* ADS1015 can handle high-speed (HS) mode (up to 3.4MHz) on I2C bus, |
| 75 |
* but SoC can handle only up to 400kHz. |
| 76 |
*/ |
| 77 |
clock-frequency = <400000>; |
| 78 |
#size-cells = <0>; |
| 79 |
status = "okay"; |
| 80 |
|
| 81 |
adc@48 { |
| 82 |
compatible = "ti,ads1015"; |
| 83 |
reg = <0x48>; |
| 84 |
#address-cells = <1>; |
| 85 |
interrupt-parent = <&gpio3>; |
| 86 |
interrupts = <RK_PC7 IRQ_TYPE_EDGE_FALLING>; |
| 87 |
pinctrl-0 = <&adc_alert>; |
| 88 |
pinctrl-names = "default"; |
| 89 |
#io-channel-cells = <1>; |
| 90 |
#size-cells = <0>; |
| 91 |
|
| 92 |
channel@1 { |
| 93 |
reg = <5>; /* Single-ended between AIN1 and GND */ |
| 94 |
ti,datarate = <0>; |
| 95 |
ti,gain = <5>; |
| 96 |
}; |
| 97 |
|
| 98 |
channel@2 { |
| 99 |
reg = <6>; /* Single-ended between AIN2 and GND */ |
| 100 |
ti,datarate = <0>; |
| 101 |
ti,gain = <5>; |
| 102 |
}; |
| 103 |
}; |
| 104 |
|
| 105 |
switch@5f { |
| 106 |
compatible = "microchip,ksz9896"; |
| 107 |
reg = <0x5f>; |
| 108 |
interrupt-parent = <&gpio3>; |
| 109 |
interrupts = <RK_PB7 IRQ_TYPE_EDGE_FALLING>; /* ETH_INTRP_N */ |
| 110 |
pinctrl-0 = <ð_reset_n ð_intrp_n>; |
| 111 |
pinctrl-names = "default"; |
| 112 |
reset-gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_LOW>; /* ETH_RESET */ |
| 113 |
microchip,synclko-disable; /* CLKO_25_125 only routed to TP1 */ |
| 114 |
|
| 115 |
ethernet-ports { |
| 116 |
#address-cells = <1>; |
| 117 |
#size-cells = <0>; |
| 118 |
|
| 119 |
lan1: port@0 { |
| 120 |
reg = <0>; |
| 121 |
label = "ETH1"; |
| 122 |
}; |
| 123 |
|
| 124 |
lan2: port@1 { |
| 125 |
reg = <1>; |
| 126 |
label = "ETH2"; |
| 127 |
}; |
| 128 |
|
| 129 |
lan3: port@2 { |
| 130 |
reg = <2>; |
| 131 |
label = "ETH3"; |
| 132 |
}; |
| 133 |
|
| 134 |
lan4: port@3 { |
| 135 |
reg = <3>; |
| 136 |
label = "ETH4"; |
| 137 |
}; |
| 138 |
|
| 139 |
port@5 { |
| 140 |
reg = <5>; |
| 141 |
ethernet = <&gmac1>; |
| 142 |
label = "CPU"; |
| 143 |
phy-mode = "rgmii-id"; |
| 144 |
rx-internal-delay-ps = <2000>; |
| 145 |
tx-internal-delay-ps = <2000>; |
| 146 |
|
| 147 |
fixed-link { |
| 148 |
speed = <1000>; |
| 149 |
full-duplex; |
| 150 |
}; |
| 151 |
}; |
| 152 |
}; |
| 153 |
}; |
| 154 |
}; |
| 155 |
|
| 156 |
&pinctrl { |
| 157 |
adc { |
| 158 |
adc_alert: adc-alert-irq { |
| 159 |
rockchip,pins = |
| 160 |
<3 RK_PC7 RK_FUNC_GPIO &pcfg_pull_up>; |
| 161 |
}; |
| 162 |
}; |
| 163 |
|
| 164 |
ethernet { |
| 165 |
eth_intrp_n: eth-intrp-n { |
| 166 |
rockchip,pins = |
| 167 |
<3 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>; |
| 168 |
}; |
| 169 |
|
| 170 |
eth_reset_n: eth-reset-n { |
| 171 |
rockchip,pins = |
| 172 |
<3 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>; |
| 173 |
}; |
| 174 |
}; |
| 175 |
|
| 176 |
leds { |
| 177 |
led_usr1_pin: led-usr1-pin { |
| 178 |
rockchip,pins = |
| 179 |
<1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>; |
| 180 |
}; |
| 181 |
|
| 182 |
led_usr2_pin: led-usr2-pin { |
| 183 |
rockchip,pins = |
| 184 |
<3 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>; |
| 185 |
}; |
| 186 |
}; |
| 187 |
}; |
| 188 |
|
| 189 |
&uart9 { |
| 190 |
/* GPIO3_D0/EN_RS485_MODE for switching between RS232 and RS485 */ |
| 191 |
pinctrl-0 = <&uart9m2_xfer &uart9m2_rtsn>; |
| 192 |
pinctrl-names = "default"; |
| 193 |
linux,rs485-enabled-at-boot-time; |
| 194 |
status = "okay"; |
| 195 |
}; |