| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Copyright (c) 2021 Rockchip Electronics Co., Ltd. |
| 4 |
*/ |
| 5 |
|
| 6 |
#include "rk3588-base.dtsi" |
| 7 |
#include "rk3588-extra-pinctrl.dtsi" |
| 8 |
|
| 9 |
/ { |
| 10 |
hdmi1_sound: hdmi1-sound { |
| 11 |
compatible = "simple-audio-card"; |
| 12 |
simple-audio-card,format = "i2s"; |
| 13 |
simple-audio-card,mclk-fs = <128>; |
| 14 |
simple-audio-card,name = "hdmi1"; |
| 15 |
status = "disabled"; |
| 16 |
|
| 17 |
simple-audio-card,codec { |
| 18 |
sound-dai = <&hdmi1>; |
| 19 |
}; |
| 20 |
|
| 21 |
simple-audio-card,cpu { |
| 22 |
sound-dai = <&i2s6_8ch>; |
| 23 |
}; |
| 24 |
}; |
| 25 |
|
| 26 |
reserved-memory { |
| 27 |
#address-cells = <2>; |
| 28 |
#size-cells = <2>; |
| 29 |
ranges; |
| 30 |
|
| 31 |
/* |
| 32 |
* The 4k HDMI capture controller works only with 32bit |
| 33 |
* phys addresses and doesn't support IOMMU. HDMI RX CMA |
| 34 |
* must be reserved below 4GB. |
| 35 |
* The size of 160MB was determined as follows: |
| 36 |
* (3840 * 2160 pixels) * (4 bytes/pixel) * (2 frames/buffer) / 10^6 = 66MB |
| 37 |
* To ensure sufficient support for practical use-cases, |
| 38 |
* we doubled the 66MB value. |
| 39 |
*/ |
| 40 |
hdmi_receiver_cma: hdmi-receiver-cma { |
| 41 |
compatible = "shared-dma-pool"; |
| 42 |
alloc-ranges = <0x0 0x0 0x0 0xffffffff>; |
| 43 |
size = <0x0 (160 * 0x100000)>; /* 160MiB */ |
| 44 |
alignment = <0x0 0x40000>; /* 64K */ |
| 45 |
no-map; |
| 46 |
status = "disabled"; |
| 47 |
}; |
| 48 |
}; |
| 49 |
|
| 50 |
usb_host1_xhci: usb@fc400000 { |
| 51 |
compatible = "rockchip,rk3588-dwc3", "snps,dwc3"; |
| 52 |
reg = <0x0 0xfc400000 0x0 0x400000>; |
| 53 |
interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH 0>; |
| 54 |
clocks = <&cru REF_CLK_USB3OTG1>, <&cru SUSPEND_CLK_USB3OTG1>, |
| 55 |
<&cru ACLK_USB3OTG1>; |
| 56 |
clock-names = "ref_clk", "suspend_clk", "bus_clk"; |
| 57 |
dr_mode = "otg"; |
| 58 |
phys = <&u2phy1_otg>, <&usbdp_phy1 PHY_TYPE_USB3>; |
| 59 |
phy-names = "usb2-phy", "usb3-phy"; |
| 60 |
phy_type = "utmi_wide"; |
| 61 |
power-domains = <&power RK3588_PD_USB>; |
| 62 |
resets = <&cru SRST_A_USB3OTG1>; |
| 63 |
snps,dis_enblslpm_quirk; |
| 64 |
snps,dis-u2-freeclk-exists-quirk; |
| 65 |
snps,dis-del-phy-power-chg-quirk; |
| 66 |
snps,dis-tx-ipgap-linecheck-quirk; |
| 67 |
status = "disabled"; |
| 68 |
}; |
| 69 |
|
| 70 |
pcie30_phy_grf: syscon@fd5b8000 { |
| 71 |
compatible = "rockchip,rk3588-pcie3-phy-grf", "syscon"; |
| 72 |
reg = <0x0 0xfd5b8000 0x0 0x10000>; |
| 73 |
}; |
| 74 |
|
| 75 |
pipe_phy1_grf: syscon@fd5c0000 { |
| 76 |
compatible = "rockchip,rk3588-pipe-phy-grf", "syscon"; |
| 77 |
reg = <0x0 0xfd5c0000 0x0 0x100>; |
| 78 |
}; |
| 79 |
|
| 80 |
usbdpphy1_grf: syscon@fd5cc000 { |
| 81 |
compatible = "rockchip,rk3588-usbdpphy-grf", "syscon"; |
| 82 |
reg = <0x0 0xfd5cc000 0x0 0x4000>; |
| 83 |
}; |
| 84 |
|
| 85 |
usb2phy1_grf: syscon@fd5d4000 { |
| 86 |
compatible = "rockchip,rk3588-usb2phy-grf", "syscon", "simple-mfd"; |
| 87 |
reg = <0x0 0xfd5d4000 0x0 0x4000>; |
| 88 |
#address-cells = <1>; |
| 89 |
#size-cells = <1>; |
| 90 |
|
| 91 |
u2phy1: usb2phy@4000 { |
| 92 |
compatible = "rockchip,rk3588-usb2phy"; |
| 93 |
reg = <0x4000 0x10>; |
| 94 |
#clock-cells = <0>; |
| 95 |
clocks = <&cru CLK_USB2PHY_HDPTXRXPHY_REF>; |
| 96 |
clock-names = "phyclk"; |
| 97 |
clock-output-names = "usb480m_phy1"; |
| 98 |
interrupts = <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH 0>; |
| 99 |
resets = <&cru SRST_OTGPHY_U3_1>, <&cru SRST_P_USB2PHY_U3_1_GRF0>; |
| 100 |
reset-names = "phy", "apb"; |
| 101 |
status = "disabled"; |
| 102 |
|
| 103 |
u2phy1_otg: otg-port { |
| 104 |
#phy-cells = <0>; |
| 105 |
status = "disabled"; |
| 106 |
}; |
| 107 |
}; |
| 108 |
}; |
| 109 |
|
| 110 |
hdptxphy1_grf: syscon@fd5e4000 { |
| 111 |
compatible = "rockchip,rk3588-hdptxphy-grf", "syscon"; |
| 112 |
reg = <0x0 0xfd5e4000 0x0 0x100>; |
| 113 |
}; |
| 114 |
|
| 115 |
spdif_tx5: spdif-tx@fddb8000 { |
| 116 |
compatible = "rockchip,rk3588-spdif", "rockchip,rk3568-spdif"; |
| 117 |
reg = <0x0 0xfddb8000 0x0 0x1000>; |
| 118 |
assigned-clock-parents = <&cru PLL_AUPLL>; |
| 119 |
assigned-clocks = <&cru CLK_SPDIF5_DP1_SRC>; |
| 120 |
clock-names = "mclk", "hclk"; |
| 121 |
clocks = <&cru MCLK_SPDIF5>, <&cru HCLK_SPDIF5_DP1>; |
| 122 |
dma-names = "tx"; |
| 123 |
dmas = <&dmac1 22>; |
| 124 |
interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH 0>; |
| 125 |
power-domains = <&power RK3588_PD_VO0>; |
| 126 |
#sound-dai-cells = <0>; |
| 127 |
status = "disabled"; |
| 128 |
}; |
| 129 |
|
| 130 |
i2s8_8ch: i2s@fddc8000 { |
| 131 |
compatible = "rockchip,rk3588-i2s-tdm"; |
| 132 |
reg = <0x0 0xfddc8000 0x0 0x1000>; |
| 133 |
interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH 0>; |
| 134 |
clocks = <&cru MCLK_I2S8_8CH_TX>, <&cru MCLK_I2S8_8CH_TX>, <&cru HCLK_I2S8_8CH>; |
| 135 |
clock-names = "mclk_tx", "mclk_rx", "hclk"; |
| 136 |
assigned-clocks = <&cru CLK_I2S8_8CH_TX_SRC>; |
| 137 |
assigned-clock-parents = <&cru PLL_AUPLL>; |
| 138 |
dmas = <&dmac2 22>; |
| 139 |
dma-names = "tx"; |
| 140 |
power-domains = <&power RK3588_PD_VO0>; |
| 141 |
resets = <&cru SRST_M_I2S8_8CH_TX>; |
| 142 |
reset-names = "tx-m"; |
| 143 |
#sound-dai-cells = <0>; |
| 144 |
status = "disabled"; |
| 145 |
}; |
| 146 |
|
| 147 |
spdif_tx4: spdif-tx@fdde8000 { |
| 148 |
compatible = "rockchip,rk3588-spdif", "rockchip,rk3568-spdif"; |
| 149 |
reg = <0x0 0xfdde8000 0x0 0x1000>; |
| 150 |
assigned-clock-parents = <&cru PLL_AUPLL>; |
| 151 |
assigned-clocks = <&cru CLK_SPDIF4_SRC>; |
| 152 |
clock-names = "mclk", "hclk"; |
| 153 |
clocks = <&cru MCLK_SPDIF4>, <&cru HCLK_SPDIF4>; |
| 154 |
dma-names = "tx"; |
| 155 |
dmas = <&dmac1 8>; |
| 156 |
interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH 0>; |
| 157 |
power-domains = <&power RK3588_PD_VO1>; |
| 158 |
#sound-dai-cells = <0>; |
| 159 |
status = "disabled"; |
| 160 |
}; |
| 161 |
|
| 162 |
i2s6_8ch: i2s@fddf4000 { |
| 163 |
compatible = "rockchip,rk3588-i2s-tdm"; |
| 164 |
reg = <0x0 0xfddf4000 0x0 0x1000>; |
| 165 |
interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH 0>; |
| 166 |
clocks = <&cru MCLK_I2S6_8CH_TX>, <&cru MCLK_I2S6_8CH_TX>, <&cru HCLK_I2S6_8CH>; |
| 167 |
clock-names = "mclk_tx", "mclk_rx", "hclk"; |
| 168 |
assigned-clocks = <&cru CLK_I2S6_8CH_TX_SRC>; |
| 169 |
assigned-clock-parents = <&cru PLL_AUPLL>; |
| 170 |
dmas = <&dmac2 4>; |
| 171 |
dma-names = "tx"; |
| 172 |
power-domains = <&power RK3588_PD_VO1>; |
| 173 |
resets = <&cru SRST_M_I2S6_8CH_TX>; |
| 174 |
reset-names = "tx-m"; |
| 175 |
#sound-dai-cells = <0>; |
| 176 |
status = "disabled"; |
| 177 |
}; |
| 178 |
|
| 179 |
i2s7_8ch: i2s@fddf8000 { |
| 180 |
compatible = "rockchip,rk3588-i2s-tdm"; |
| 181 |
reg = <0x0 0xfddf8000 0x0 0x1000>; |
| 182 |
interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH 0>; |
| 183 |
clocks = <&cru MCLK_I2S7_8CH_RX>, <&cru MCLK_I2S7_8CH_RX>, <&cru HCLK_I2S7_8CH>; |
| 184 |
clock-names = "mclk_tx", "mclk_rx", "hclk"; |
| 185 |
assigned-clocks = <&cru CLK_I2S7_8CH_RX_SRC>; |
| 186 |
assigned-clock-parents = <&cru PLL_AUPLL>; |
| 187 |
dmas = <&dmac2 21>; |
| 188 |
dma-names = "rx"; |
| 189 |
power-domains = <&power RK3588_PD_VO1>; |
| 190 |
resets = <&cru SRST_M_I2S7_8CH_RX>; |
| 191 |
reset-names = "rx-m"; |
| 192 |
#sound-dai-cells = <0>; |
| 193 |
status = "disabled"; |
| 194 |
}; |
| 195 |
|
| 196 |
i2s10_8ch: i2s@fde00000 { |
| 197 |
compatible = "rockchip,rk3588-i2s-tdm"; |
| 198 |
reg = <0x0 0xfde00000 0x0 0x1000>; |
| 199 |
interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH 0>; |
| 200 |
clocks = <&cru MCLK_I2S10_8CH_RX>, <&cru MCLK_I2S10_8CH_RX>, <&cru HCLK_I2S10_8CH>; |
| 201 |
clock-names = "mclk_tx", "mclk_rx", "hclk"; |
| 202 |
assigned-clocks = <&cru CLK_I2S10_8CH_RX_SRC>; |
| 203 |
assigned-clock-parents = <&cru PLL_AUPLL>; |
| 204 |
dmas = <&dmac2 24>; |
| 205 |
dma-names = "rx"; |
| 206 |
power-domains = <&power RK3588_PD_VO1>; |
| 207 |
resets = <&cru SRST_M_I2S10_8CH_RX>; |
| 208 |
reset-names = "rx-m"; |
| 209 |
#sound-dai-cells = <0>; |
| 210 |
status = "disabled"; |
| 211 |
}; |
| 212 |
|
| 213 |
dp1: dp@fde60000 { |
| 214 |
compatible = "rockchip,rk3588-dp"; |
| 215 |
reg = <0x0 0xfde60000 0x0 0x4000>; |
| 216 |
interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH 0>; |
| 217 |
assigned-clocks = <&cru CLK_AUX16M_1>; |
| 218 |
assigned-clock-rates = <16000000>; |
| 219 |
clocks = <&cru PCLK_DP1>, <&cru CLK_AUX16M_1>, |
| 220 |
<&cru CLK_DP1>, <&cru MCLK_I2S8_8CH_TX>, |
| 221 |
<&cru MCLK_SPDIF5_DP1>; |
| 222 |
clock-names = "apb", "aux", "hdcp", "i2s", "spdif"; |
| 223 |
phys = <&usbdp_phy1 PHY_TYPE_DP>; |
| 224 |
power-domains = <&power RK3588_PD_VO0>; |
| 225 |
resets = <&cru SRST_DP1>; |
| 226 |
#sound-dai-cells = <0>; |
| 227 |
status = "disabled"; |
| 228 |
|
| 229 |
ports { |
| 230 |
#address-cells = <1>; |
| 231 |
#size-cells = <0>; |
| 232 |
|
| 233 |
dp1_in: port@0 { |
| 234 |
reg = <0>; |
| 235 |
}; |
| 236 |
|
| 237 |
dp1_out: port@1 { |
| 238 |
reg = <1>; |
| 239 |
}; |
| 240 |
}; |
| 241 |
}; |
| 242 |
|
| 243 |
hdmi1: hdmi@fdea0000 { |
| 244 |
compatible = "rockchip,rk3588-dw-hdmi-qp"; |
| 245 |
reg = <0x0 0xfdea0000 0x0 0x20000>; |
| 246 |
clocks = <&cru PCLK_HDMITX1>, |
| 247 |
<&cru CLK_HDMITX1_EARC>, |
| 248 |
<&cru CLK_HDMITX1_REF>, |
| 249 |
<&cru MCLK_I2S6_8CH_TX>, |
| 250 |
<&cru CLK_HDMIHDP1>, |
| 251 |
<&cru HCLK_VO1>; |
| 252 |
clock-names = "pclk", "earc", "ref", "aud", "hdp", "hclk_vo1"; |
| 253 |
interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH 0>, |
| 254 |
<GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH 0>, |
| 255 |
<GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH 0>, |
| 256 |
<GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH 0>, |
| 257 |
<GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH 0>; |
| 258 |
interrupt-names = "avp", "cec", "earc", "main", "hpd"; |
| 259 |
phys = <&hdptxphy1>; |
| 260 |
pinctrl-names = "default"; |
| 261 |
pinctrl-0 = <&hdmim2_tx1_cec &hdmim0_tx1_hpd |
| 262 |
&hdmim1_tx1_scl &hdmim1_tx1_sda>; |
| 263 |
power-domains = <&power RK3588_PD_VO1>; |
| 264 |
resets = <&cru SRST_HDMITX1_REF>, <&cru SRST_HDMIHDP1>; |
| 265 |
reset-names = "ref", "hdp"; |
| 266 |
rockchip,grf = <&sys_grf>; |
| 267 |
rockchip,vo-grf = <&vo1_grf>; |
| 268 |
#sound-dai-cells = <0>; |
| 269 |
status = "disabled"; |
| 270 |
|
| 271 |
ports { |
| 272 |
#address-cells = <1>; |
| 273 |
#size-cells = <0>; |
| 274 |
|
| 275 |
hdmi1_in: port@0 { |
| 276 |
reg = <0>; |
| 277 |
}; |
| 278 |
|
| 279 |
hdmi1_out: port@1 { |
| 280 |
reg = <1>; |
| 281 |
}; |
| 282 |
}; |
| 283 |
}; |
| 284 |
|
| 285 |
edp1: edp@fded0000 { |
| 286 |
compatible = "rockchip,rk3588-edp"; |
| 287 |
reg = <0x0 0xfded0000 0x0 0x1000>; |
| 288 |
clocks = <&cru CLK_EDP1_24M>, <&cru PCLK_EDP1>; |
| 289 |
clock-names = "dp", "pclk"; |
| 290 |
interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH 0>; |
| 291 |
phys = <&hdptxphy1>; |
| 292 |
phy-names = "dp"; |
| 293 |
power-domains = <&power RK3588_PD_VO1>; |
| 294 |
resets = <&cru SRST_EDP1_24M>, <&cru SRST_P_EDP1>; |
| 295 |
reset-names = "dp", "apb"; |
| 296 |
rockchip,grf = <&vo1_grf>; |
| 297 |
status = "disabled"; |
| 298 |
|
| 299 |
ports { |
| 300 |
#address-cells = <1>; |
| 301 |
#size-cells = <0>; |
| 302 |
|
| 303 |
edp1_in: port@0 { |
| 304 |
reg = <0>; |
| 305 |
}; |
| 306 |
|
| 307 |
edp1_out: port@1 { |
| 308 |
reg = <1>; |
| 309 |
}; |
| 310 |
}; |
| 311 |
}; |
| 312 |
|
| 313 |
hdmi_receiver: hdmi_receiver@fdee0000 { |
| 314 |
compatible = "rockchip,rk3588-hdmirx-ctrler", "snps,dw-hdmi-rx"; |
| 315 |
reg = <0x0 0xfdee0000 0x0 0x6000>; |
| 316 |
interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH 0>, |
| 317 |
<GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH 0>, |
| 318 |
<GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH 0>; |
| 319 |
interrupt-names = "cec", "hdmi", "dma"; |
| 320 |
clocks = <&cru ACLK_HDMIRX>, |
| 321 |
<&cru CLK_HDMIRX_AUD>, |
| 322 |
<&cru CLK_CR_PARA>, |
| 323 |
<&cru PCLK_HDMIRX>, |
| 324 |
<&cru CLK_HDMIRX_REF>, |
| 325 |
<&cru PCLK_S_HDMIRX>, |
| 326 |
<&cru HCLK_VO1>; |
| 327 |
clock-names = "aclk", |
| 328 |
"audio", |
| 329 |
"cr_para", |
| 330 |
"pclk", |
| 331 |
"ref", |
| 332 |
"hclk_s_hdmirx", |
| 333 |
"hclk_vo1"; |
| 334 |
memory-region = <&hdmi_receiver_cma>; |
| 335 |
power-domains = <&power RK3588_PD_VO1>; |
| 336 |
resets = <&cru SRST_A_HDMIRX>, <&cru SRST_P_HDMIRX>, |
| 337 |
<&cru SRST_HDMIRX_REF>, <&cru SRST_A_HDMIRX_BIU>; |
| 338 |
reset-names = "axi", "apb", "ref", "biu"; |
| 339 |
rockchip,grf = <&sys_grf>; |
| 340 |
rockchip,vo1-grf = <&vo1_grf>; |
| 341 |
status = "disabled"; |
| 342 |
}; |
| 343 |
|
| 344 |
pcie3x4: pcie@fe150000 { |
| 345 |
compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie"; |
| 346 |
#address-cells = <3>; |
| 347 |
#size-cells = <2>; |
| 348 |
bus-range = <0x00 0x0f>; |
| 349 |
clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>, |
| 350 |
<&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>, |
| 351 |
<&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>; |
| 352 |
clock-names = "aclk_mst", "aclk_slv", |
| 353 |
"aclk_dbi", "pclk", |
| 354 |
"aux", "pipe"; |
| 355 |
device_type = "pci"; |
| 356 |
interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH 0>, |
| 357 |
<GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH 0>, |
| 358 |
<GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH 0>, |
| 359 |
<GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH 0>, |
| 360 |
<GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH 0>; |
| 361 |
interrupt-names = "sys", "pmc", "msg", "legacy", "err"; |
| 362 |
#interrupt-cells = <1>; |
| 363 |
interrupt-map-mask = <0 0 0 7>; |
| 364 |
interrupt-map = <0 0 0 1 &pcie3x4_intc 0>, |
| 365 |
<0 0 0 2 &pcie3x4_intc 1>, |
| 366 |
<0 0 0 3 &pcie3x4_intc 2>, |
| 367 |
<0 0 0 4 &pcie3x4_intc 3>; |
| 368 |
linux,pci-domain = <0>; |
| 369 |
max-link-speed = <3>; |
| 370 |
msi-map = <0x0000 &its1 0x0000 0x1000>; |
| 371 |
iommu-map = <0x0000 &mmu600_pcie 0x0000 0x1000>; |
| 372 |
num-lanes = <4>; |
| 373 |
phys = <&pcie30phy>; |
| 374 |
phy-names = "pcie-phy"; |
| 375 |
power-domains = <&power RK3588_PD_PCIE>; |
| 376 |
ranges = <0x01000000 0x0 0xf0100000 0x0 0xf0100000 0x0 0x00100000>, |
| 377 |
<0x02000000 0x0 0xf0200000 0x0 0xf0200000 0x0 0x00e00000>, |
| 378 |
<0x03000000 0x9 0x00000000 0x9 0x00000000 0x0 0x40000000>; |
| 379 |
reg = <0xa 0x40000000 0x0 0x00400000>, |
| 380 |
<0x0 0xfe150000 0x0 0x00010000>, |
| 381 |
<0x0 0xf0000000 0x0 0x00100000>; |
| 382 |
reg-names = "dbi", "apb", "config"; |
| 383 |
resets = <&cru SRST_PCIE0_POWER_UP>, <&cru SRST_P_PCIE0>; |
| 384 |
reset-names = "pwr", "pipe"; |
| 385 |
status = "disabled"; |
| 386 |
|
| 387 |
pcie3x4_intc: legacy-interrupt-controller { |
| 388 |
interrupt-controller; |
| 389 |
#address-cells = <0>; |
| 390 |
#interrupt-cells = <1>; |
| 391 |
interrupt-parent = <&gic>; |
| 392 |
interrupts = <GIC_SPI 260 IRQ_TYPE_EDGE_RISING 0>; |
| 393 |
}; |
| 394 |
}; |
| 395 |
|
| 396 |
pcie3x4_ep: pcie-ep@fe150000 { |
| 397 |
compatible = "rockchip,rk3588-pcie-ep"; |
| 398 |
reg = <0xa 0x40000000 0x0 0x00100000>, |
| 399 |
<0xa 0x40100000 0x0 0x00100000>, |
| 400 |
<0x0 0xfe150000 0x0 0x00010000>, |
| 401 |
<0x9 0x00000000 0x0 0x40000000>, |
| 402 |
<0xa 0x40300000 0x0 0x00100000>; |
| 403 |
reg-names = "dbi", "dbi2", "apb", "addr_space", "atu"; |
| 404 |
clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>, |
| 405 |
<&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>, |
| 406 |
<&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>; |
| 407 |
clock-names = "aclk_mst", "aclk_slv", |
| 408 |
"aclk_dbi", "pclk", |
| 409 |
"aux", "pipe"; |
| 410 |
interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH 0>, |
| 411 |
<GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH 0>, |
| 412 |
<GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH 0>, |
| 413 |
<GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH 0>, |
| 414 |
<GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH 0>, |
| 415 |
<GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH 0>, |
| 416 |
<GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH 0>, |
| 417 |
<GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH 0>, |
| 418 |
<GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH 0>; |
| 419 |
interrupt-names = "sys", "pmc", "msg", "legacy", "err", |
| 420 |
"dma0", "dma1", "dma2", "dma3"; |
| 421 |
max-link-speed = <3>; |
| 422 |
num-lanes = <4>; |
| 423 |
phys = <&pcie30phy>; |
| 424 |
phy-names = "pcie-phy"; |
| 425 |
power-domains = <&power RK3588_PD_PCIE>; |
| 426 |
resets = <&cru SRST_PCIE0_POWER_UP>, <&cru SRST_P_PCIE0>; |
| 427 |
reset-names = "pwr", "pipe"; |
| 428 |
status = "disabled"; |
| 429 |
}; |
| 430 |
|
| 431 |
pcie3x2: pcie@fe160000 { |
| 432 |
compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie"; |
| 433 |
#address-cells = <3>; |
| 434 |
#size-cells = <2>; |
| 435 |
bus-range = <0x10 0x1f>; |
| 436 |
clocks = <&cru ACLK_PCIE_2L_MSTR>, <&cru ACLK_PCIE_2L_SLV>, |
| 437 |
<&cru ACLK_PCIE_2L_DBI>, <&cru PCLK_PCIE_2L>, |
| 438 |
<&cru CLK_PCIE_AUX1>, <&cru CLK_PCIE2L_PIPE>; |
| 439 |
clock-names = "aclk_mst", "aclk_slv", |
| 440 |
"aclk_dbi", "pclk", |
| 441 |
"aux", "pipe"; |
| 442 |
device_type = "pci"; |
| 443 |
interrupts = <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH 0>, |
| 444 |
<GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH 0>, |
| 445 |
<GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH 0>, |
| 446 |
<GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH 0>, |
| 447 |
<GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH 0>; |
| 448 |
interrupt-names = "sys", "pmc", "msg", "legacy", "err"; |
| 449 |
#interrupt-cells = <1>; |
| 450 |
interrupt-map-mask = <0 0 0 7>; |
| 451 |
interrupt-map = <0 0 0 1 &pcie3x2_intc 0>, |
| 452 |
<0 0 0 2 &pcie3x2_intc 1>, |
| 453 |
<0 0 0 3 &pcie3x2_intc 2>, |
| 454 |
<0 0 0 4 &pcie3x2_intc 3>; |
| 455 |
linux,pci-domain = <1>; |
| 456 |
max-link-speed = <3>; |
| 457 |
msi-map = <0x1000 &its1 0x1000 0x1000>; |
| 458 |
iommu-map = <0x1000 &mmu600_pcie 0x1000 0x1000>; |
| 459 |
num-lanes = <2>; |
| 460 |
phys = <&pcie30phy>; |
| 461 |
phy-names = "pcie-phy"; |
| 462 |
power-domains = <&power RK3588_PD_PCIE>; |
| 463 |
ranges = <0x01000000 0x0 0xf1100000 0x0 0xf1100000 0x0 0x00100000>, |
| 464 |
<0x02000000 0x0 0xf1200000 0x0 0xf1200000 0x0 0x00e00000>, |
| 465 |
<0x03000000 0x9 0x40000000 0x9 0x40000000 0x0 0x40000000>; |
| 466 |
reg = <0xa 0x40400000 0x0 0x00400000>, |
| 467 |
<0x0 0xfe160000 0x0 0x00010000>, |
| 468 |
<0x0 0xf1000000 0x0 0x00100000>; |
| 469 |
reg-names = "dbi", "apb", "config"; |
| 470 |
resets = <&cru SRST_PCIE1_POWER_UP>, <&cru SRST_P_PCIE1>; |
| 471 |
reset-names = "pwr", "pipe"; |
| 472 |
status = "disabled"; |
| 473 |
|
| 474 |
pcie3x2_intc: legacy-interrupt-controller { |
| 475 |
interrupt-controller; |
| 476 |
#address-cells = <0>; |
| 477 |
#interrupt-cells = <1>; |
| 478 |
interrupt-parent = <&gic>; |
| 479 |
interrupts = <GIC_SPI 255 IRQ_TYPE_EDGE_RISING 0>; |
| 480 |
}; |
| 481 |
}; |
| 482 |
|
| 483 |
pcie2x1l0: pcie@fe170000 { |
| 484 |
compatible = "rockchip,rk3588-pcie", "rockchip,rk3568-pcie"; |
| 485 |
bus-range = <0x20 0x2f>; |
| 486 |
clocks = <&cru ACLK_PCIE_1L0_MSTR>, <&cru ACLK_PCIE_1L0_SLV>, |
| 487 |
<&cru ACLK_PCIE_1L0_DBI>, <&cru PCLK_PCIE_1L0>, |
| 488 |
<&cru CLK_PCIE_AUX2>, <&cru CLK_PCIE1L0_PIPE>; |
| 489 |
clock-names = "aclk_mst", "aclk_slv", |
| 490 |
"aclk_dbi", "pclk", |
| 491 |
"aux", "pipe"; |
| 492 |
device_type = "pci"; |
| 493 |
interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>, |
| 494 |
<GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH 0>, |
| 495 |
<GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH 0>, |
| 496 |
<GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH 0>, |
| 497 |
<GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH 0>; |
| 498 |
interrupt-names = "sys", "pmc", "msg", "legacy", "err"; |
| 499 |
#interrupt-cells = <1>; |
| 500 |
interrupt-map-mask = <0 0 0 7>; |
| 501 |
interrupt-map = <0 0 0 1 &pcie2x1l0_intc 0>, |
| 502 |
<0 0 0 2 &pcie2x1l0_intc 1>, |
| 503 |
<0 0 0 3 &pcie2x1l0_intc 2>, |
| 504 |
<0 0 0 4 &pcie2x1l0_intc 3>; |
| 505 |
linux,pci-domain = <2>; |
| 506 |
max-link-speed = <2>; |
| 507 |
msi-map = <0x2000 &its0 0x2000 0x1000>; |
| 508 |
iommu-map = <0x2000 &mmu600_pcie 0x2000 0x1000>; |
| 509 |
num-lanes = <1>; |
| 510 |
phys = <&combphy1_ps PHY_TYPE_PCIE>; |
| 511 |
phy-names = "pcie-phy"; |
| 512 |
power-domains = <&power RK3588_PD_PCIE>; |
| 513 |
ranges = <0x01000000 0x0 0xf2100000 0x0 0xf2100000 0x0 0x00100000>, |
| 514 |
<0x02000000 0x0 0xf2200000 0x0 0xf2200000 0x0 0x00e00000>, |
| 515 |
<0x03000000 0x9 0x80000000 0x9 0x80000000 0x0 0x40000000>; |
| 516 |
reg = <0xa 0x40800000 0x0 0x00400000>, |
| 517 |
<0x0 0xfe170000 0x0 0x00010000>, |
| 518 |
<0x0 0xf2000000 0x0 0x00100000>; |
| 519 |
reg-names = "dbi", "apb", "config"; |
| 520 |
resets = <&cru SRST_PCIE2_POWER_UP>, <&cru SRST_P_PCIE2>; |
| 521 |
reset-names = "pwr", "pipe"; |
| 522 |
#address-cells = <3>; |
| 523 |
#size-cells = <2>; |
| 524 |
status = "disabled"; |
| 525 |
|
| 526 |
pcie2x1l0_intc: legacy-interrupt-controller { |
| 527 |
interrupt-controller; |
| 528 |
#address-cells = <0>; |
| 529 |
#interrupt-cells = <1>; |
| 530 |
interrupt-parent = <&gic>; |
| 531 |
interrupts = <GIC_SPI 240 IRQ_TYPE_EDGE_RISING 0>; |
| 532 |
}; |
| 533 |
}; |
| 534 |
|
| 535 |
gmac0: ethernet@fe1b0000 { |
| 536 |
compatible = "rockchip,rk3588-gmac", "snps,dwmac-4.20a"; |
| 537 |
reg = <0x0 0xfe1b0000 0x0 0x10000>; |
| 538 |
interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH 0>, |
| 539 |
<GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH 0>; |
| 540 |
interrupt-names = "macirq", "eth_wake_irq"; |
| 541 |
clocks = <&cru CLK_GMAC_125M>, <&cru CLK_GMAC_50M>, |
| 542 |
<&cru PCLK_GMAC0>, <&cru ACLK_GMAC0>, |
| 543 |
<&cru CLK_GMAC0_PTP_REF>; |
| 544 |
clock-names = "stmmaceth", "clk_mac_ref", |
| 545 |
"pclk_mac", "aclk_mac", |
| 546 |
"ptp_ref"; |
| 547 |
power-domains = <&power RK3588_PD_GMAC>; |
| 548 |
resets = <&cru SRST_A_GMAC0>; |
| 549 |
reset-names = "stmmaceth"; |
| 550 |
rockchip,grf = <&sys_grf>; |
| 551 |
rockchip,php-grf = <&php_grf>; |
| 552 |
snps,axi-config = <&gmac0_stmmac_axi_setup>; |
| 553 |
snps,mixed-burst; |
| 554 |
snps,mtl-rx-config = <&gmac0_mtl_rx_setup>; |
| 555 |
snps,mtl-tx-config = <&gmac0_mtl_tx_setup>; |
| 556 |
snps,tso; |
| 557 |
status = "disabled"; |
| 558 |
|
| 559 |
mdio0: mdio { |
| 560 |
compatible = "snps,dwmac-mdio"; |
| 561 |
#address-cells = <0x1>; |
| 562 |
#size-cells = <0x0>; |
| 563 |
}; |
| 564 |
|
| 565 |
gmac0_stmmac_axi_setup: stmmac-axi-config { |
| 566 |
snps,blen = <0 0 0 0 16 8 4>; |
| 567 |
snps,wr_osr_lmt = <4>; |
| 568 |
snps,rd_osr_lmt = <8>; |
| 569 |
}; |
| 570 |
|
| 571 |
gmac0_mtl_rx_setup: rx-queues-config { |
| 572 |
snps,rx-queues-to-use = <2>; |
| 573 |
queue0 {}; |
| 574 |
queue1 {}; |
| 575 |
}; |
| 576 |
|
| 577 |
gmac0_mtl_tx_setup: tx-queues-config { |
| 578 |
snps,tx-queues-to-use = <2>; |
| 579 |
queue0 {}; |
| 580 |
queue1 {}; |
| 581 |
}; |
| 582 |
}; |
| 583 |
|
| 584 |
sata1: sata@fe220000 { |
| 585 |
compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci"; |
| 586 |
reg = <0 0xfe220000 0 0x1000>; |
| 587 |
interrupts = <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH 0>; |
| 588 |
clocks = <&cru ACLK_SATA1>, <&cru CLK_PMALIVE1>, |
| 589 |
<&cru CLK_RXOOB1>, <&cru CLK_PIPEPHY1_REF>, |
| 590 |
<&cru CLK_PIPEPHY1_PIPE_ASIC_G>; |
| 591 |
clock-names = "sata", "pmalive", "rxoob", "ref", "asic"; |
| 592 |
ports-implemented = <0x1>; |
| 593 |
#address-cells = <1>; |
| 594 |
#size-cells = <0>; |
| 595 |
status = "disabled"; |
| 596 |
|
| 597 |
sata-port@0 { |
| 598 |
reg = <0>; |
| 599 |
hba-port-cap = <HBA_PORT_FBSCP>; |
| 600 |
phys = <&combphy1_ps PHY_TYPE_SATA>; |
| 601 |
phy-names = "sata-phy"; |
| 602 |
snps,rx-ts-max = <32>; |
| 603 |
snps,tx-ts-max = <32>; |
| 604 |
}; |
| 605 |
}; |
| 606 |
|
| 607 |
hdptxphy1: phy@fed70000 { |
| 608 |
compatible = "rockchip,rk3588-hdptx-phy"; |
| 609 |
reg = <0x0 0xfed70000 0x0 0x2000>; |
| 610 |
clocks = <&cru CLK_USB2PHY_HDPTXRXPHY_REF>, <&cru PCLK_HDPTX1>; |
| 611 |
clock-names = "ref", "apb"; |
| 612 |
#clock-cells = <0>; |
| 613 |
#phy-cells = <0>; |
| 614 |
resets = <&cru SRST_HDPTX1>, <&cru SRST_P_HDPTX1>, |
| 615 |
<&cru SRST_HDPTX1_INIT>, <&cru SRST_HDPTX1_CMN>, |
| 616 |
<&cru SRST_HDPTX1_LANE>, <&cru SRST_HDPTX1_ROPLL>, |
| 617 |
<&cru SRST_HDPTX1_LCPLL>; |
| 618 |
reset-names = "phy", "apb", "init", "cmn", "lane", "ropll", |
| 619 |
"lcpll"; |
| 620 |
rockchip,grf = <&hdptxphy1_grf>; |
| 621 |
status = "disabled"; |
| 622 |
}; |
| 623 |
|
| 624 |
usbdp_phy1: phy@fed90000 { |
| 625 |
compatible = "rockchip,rk3588-usbdp-phy"; |
| 626 |
reg = <0x0 0xfed90000 0x0 0x10000>; |
| 627 |
#phy-cells = <1>; |
| 628 |
clocks = <&cru CLK_USBDPPHY_MIPIDCPPHY_REF>, |
| 629 |
<&cru CLK_USBDP_PHY1_IMMORTAL>, |
| 630 |
<&cru PCLK_USBDPPHY1>, |
| 631 |
<&u2phy1>; |
| 632 |
clock-names = "refclk", "immortal", "pclk", "utmi"; |
| 633 |
resets = <&cru SRST_USBDP_COMBO_PHY1_INIT>, |
| 634 |
<&cru SRST_USBDP_COMBO_PHY1_CMN>, |
| 635 |
<&cru SRST_USBDP_COMBO_PHY1_LANE>, |
| 636 |
<&cru SRST_USBDP_COMBO_PHY1_PCS>, |
| 637 |
<&cru SRST_P_USBDPPHY1>; |
| 638 |
reset-names = "init", "cmn", "lane", "pcs_apb", "pma_apb"; |
| 639 |
rockchip,u2phy-grf = <&usb2phy1_grf>; |
| 640 |
rockchip,usb-grf = <&usb_grf>; |
| 641 |
rockchip,usbdpphy-grf = <&usbdpphy1_grf>; |
| 642 |
rockchip,vo-grf = <&vo0_grf>; |
| 643 |
status = "disabled"; |
| 644 |
}; |
| 645 |
|
| 646 |
combphy1_ps: phy@fee10000 { |
| 647 |
compatible = "rockchip,rk3588-naneng-combphy"; |
| 648 |
reg = <0x0 0xfee10000 0x0 0x100>; |
| 649 |
clocks = <&cru CLK_REF_PIPE_PHY1>, <&cru PCLK_PCIE_COMBO_PIPE_PHY1>, |
| 650 |
<&cru PCLK_PHP_ROOT>; |
| 651 |
clock-names = "ref", "apb", "pipe"; |
| 652 |
assigned-clocks = <&cru CLK_REF_PIPE_PHY1>; |
| 653 |
assigned-clock-rates = <100000000>; |
| 654 |
#phy-cells = <1>; |
| 655 |
resets = <&cru SRST_REF_PIPE_PHY1>, <&cru SRST_P_PCIE2_PHY1>; |
| 656 |
reset-names = "phy", "apb"; |
| 657 |
rockchip,pipe-grf = <&php_grf>; |
| 658 |
rockchip,pipe-phy-grf = <&pipe_phy1_grf>; |
| 659 |
status = "disabled"; |
| 660 |
}; |
| 661 |
|
| 662 |
pcie30phy: phy@fee80000 { |
| 663 |
compatible = "rockchip,rk3588-pcie3-phy"; |
| 664 |
reg = <0x0 0xfee80000 0x0 0x20000>; |
| 665 |
#phy-cells = <0>; |
| 666 |
clocks = <&cru PCLK_PCIE_COMBO_PIPE_PHY>; |
| 667 |
clock-names = "pclk"; |
| 668 |
resets = <&cru SRST_PCIE30_PHY>; |
| 669 |
reset-names = "phy"; |
| 670 |
rockchip,pipe-grf = <&php_grf>; |
| 671 |
rockchip,phy-grf = <&pcie30_phy_grf>; |
| 672 |
status = "disabled"; |
| 673 |
}; |
| 674 |
}; |
| 675 |
|
| 676 |
&vop { |
| 677 |
clocks = <&cru ACLK_VOP>, |
| 678 |
<&cru HCLK_VOP>, |
| 679 |
<&cru DCLK_VOP0>, |
| 680 |
<&cru DCLK_VOP1>, |
| 681 |
<&cru DCLK_VOP2>, |
| 682 |
<&cru DCLK_VOP3>, |
| 683 |
<&cru PCLK_VOP_ROOT>, |
| 684 |
<&hdptxphy0>, |
| 685 |
<&hdptxphy1>; |
| 686 |
clock-names = "aclk", |
| 687 |
"hclk", |
| 688 |
"dclk_vp0", |
| 689 |
"dclk_vp1", |
| 690 |
"dclk_vp2", |
| 691 |
"dclk_vp3", |
| 692 |
"pclk_vop", |
| 693 |
"pll_hdmiphy0", |
| 694 |
"pll_hdmiphy1"; |
| 695 |
}; |